EN DE User Manual Dishwasher Benutzerinformation Geschirrspüler 2 22 FAVORIT 66705 VI1P
www.aeg.com CONTENTS 1. SAFETY INFORMATION...........................................................................................3 2. SAFETY INSTRUCTIONS.......................................................................................... 4 3. PRODUCT DESCRIPTION........................................................................................ 5 4. CONTROL PANEL.....................................................................................................6 5. PROGRAMMES.............
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com • • • • • • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
ENGLISH WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is completed.
www.aeg.com 5 6 7 8 9 Rating plate Salt container Air vent Rinse aid dispenser Detergent dispenser 10 Lower basket 11 Upper basket 12 Cutlery drawer 3.1 Beam-on-Floor • When the appliance has a malfunction, the red light flashes. The Beam-on-Floor is a light that shows on the kitchen floor below the appliance door. The Beam-on-Floor goes off when the appliance is deactivated. • When the programme starts, a red light comes on and stays on for all the duration of the programme.
ENGLISH 7 5.
www.aeg.com Programme 1) Water (l) Energy (kWh) Duration (min) P2 7 - 14 0.6 - 1.4 40 - 150 P3 12.5 - 14.5 1.4 - 1.6 154 - 164 P4 12 - 14 0.7 - 0.9 75 - 85 P5 10 0.9 30 P6 9 - 10 1.0 - 1.2 219 - 229 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes For all the necessary information for test performance, send an email to: info.
ENGLISH The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water 9 in your area. It is important to set the right level of the water softener to assure good washing results. Water hardness German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.
www.aeg.com How to set the rinse aid level 2. Press . The appliance must be in programme selection mode. • The indicators off. 1. To enter the user mode, press and continues to • The indicator flash. • The display shows the current hold simultaneously and until , , and the indicators start to flash and the display is blank. 2. Press . • The indicators off. , and go • The indicator continues to flash. • The display shows the current setting: e.g. = level 4.
ENGLISH 11 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you have selected non compatible options, the appliance will automatically deactivate one or more of them. Only the indicators of the options still active will stay on. 7.1 XtraDry Activate this option when you want to boost the drying performance.
www.aeg.com inside the appliance. Do not use detergent and do not load the baskets. When you start a programme, the appliance can take up to 5 minutes to recharge the resin in the water softener. It seems that the appliance is not working. The washing phase starts only after this procedure is completed. The procedure will be repeated periodically. 8.1 The salt container Water and salt can come out from the salt container when you fill it. Risk of corrosion.
ENGLISH 13 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil. 9.1 Using the detergent A B C CAUTION! Only use detergent specifically designed for dishwashers.
www.aeg.com Opening the door while the appliance operates Press and hold RESET until the appliance is in programme selection mode. If you open the door while a programme is running, the appliance stops. It may affect the energy consumption and the programme duration. When you close the door, the appliance continues from the point of interruption. Cancelling the programme If the door is opened for more than 30 seconds during the drying phase, the running programme will end.
ENGLISH 10.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5.
www.aeg.com C B A 1. Turn the filter (B) counterclockwise and remove it. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 4. Wash the filters.
ENGLISH 11.2 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. 17 4. To engage again the spray arm to the basket, press the spray arm upwards in the direction indicated by the lower arrow and simultaneously turn it counterclockwise until it locks into place. Clogged holes can cause unsatisfactory washing results. 1. Pull out the upper basket. 2.
www.aeg.com With some problems, the display shows an alarm code. to contact an Authorised Service Centre. The majority of problems that can occur can be solved without the need Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The program does not start. • Make sure that the appliance door is closed.
ENGLISH 19 Problem and alarm code Possible cause and solution Small leak from the appliance door. • The appliance is not level. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if applicable). The appliance door is difficult to close. • The appliance is not level. Loosen or tighten the adjustable feet (if applicable). • Parts of the tableware are protruding from the baskets.
www.aeg.com Problem Possible cause and solution There are stains and dry water drops on glasses and dishes. • The released quantity of rinse aid is not sufficient. Adjust the rinse aid level to a higher level. • The quality of the rinse aid can be the cause. The dishes are wet. • For the best drying performance activate the option XtraDry. • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty.
ENGLISH 21 13. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818-898 / 550 Electrical connection 1) Voltage (V) 200 - 240 Frequency (Hz) 50 / 60 bar (minimum and maximum) 0.5 - 8 MPa (minimum and maximum) 0.05 - 0.8 Capacity Place settings 15 Power consumption Left-on mode (W) 0.99 Power consumption Off-mode (W) 0.10 Water supply pressure 1) Refer to the rating plate for other values. 14. ENVIRONMENT CONCERNS Recycle the materials with the symbol .
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.......................................................................... 23 2. SICHERHEITSANWEISUNGEN.............................................................................. 24 3. GERÄTEBESCHREIBUNG.......................................................................................26 4. BEDIENFELD........................................................................................................... 27 5. PROGRAMME.................
DEUTSCH 1. 23 SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.
www.aeg.com • • • • • • • • Beachten Sie, dass die Höchstzahl an Maßgedecken 15 beträgt. Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, seinem autorisierten Kundenservice oder einer gleichermaßen qualifizierten Person ausgetauscht werden, um Gefahrenquellen zu vermeiden. Stellen Sie Messer und Besteck mit scharfen Spitzen mit der Spitze nach unten in den Besteckkorb oder legen Sie sie waagerecht in das Gerät.
DEUTSCH • Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. • Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen. • Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose. Stellen Sie sicher, dass der Netzstecker nach der Montage noch zugänglich ist.
www.aeg.com 3. GERÄTEBESCHREIBUNG 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Oberster Sprüharm Oberer Sprüharm Unterer Sprüharm Filter Typenschild Salzbehälter Lüftungsschlitze 3.1 Beam-on-Floor Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Küchenboden projiziert wird. • Nach dem Start des Programms leuchtet der rote Lichtstrahl auf und bleibt während der gesamten Programmdauer eingeschaltet.
DEUTSCH 27 4. BEDIENFELD 1 1 2 3 4 5 2 3 Taste „Ein/Aus“ Display Taste Delay Taste Program Taste ExtraHygiene 4 6 7 8 9 5 6 7 8 9 Taste TimeSaver Taste XtraDry Taste RESET Kontrolllampen 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe Programmende. Kontrolllampe XtraDry. Kontrolllampe Salz. Sie erlischt während des Programmbetriebs. Kontrolllampe Klarspülmittel. Sie erlischt während des Programmbetriebs. 5.
www.aeg.
DEUTSCH Programm 1) Wasser (l) Energieverbrauch (kWh) Dauer (Min.) P4 12 - 14 0.7 - 0.9 75 - 85 P5 10 0.9 30 P6 9 - 10 1.0 - 1.2 219 - 229 29 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Informationen für Prüfinstitute Möchten Sie Informationen zum Leistungstest erhalten, schicken Sie eine E-Mail an: info.test@dishwasher-production.
www.aeg.com Wasserhärte Deutsche Wasserhärtegrade (°dH) Französische Wasserhärtegrade (°fH) mmol/l Clarke Was- Einstellung für den serhärteWasserenthärter grade 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.
DEUTSCH Ausschalten des KlarspülmittelDosierers Werkseitige Einstellung: Stufe 4. Einstellen der Klarspülmittelstufe Das Gerät muss sich im Programmwahlmodus befinden. Das Gerät muss sich im Programmwahlmodus befinden. 1. Halten Sie zum Aufrufen des Benutzermodus gleichzeitig 1. Halten Sie zum Aufrufen des Benutzermodus gleichzeitig und gedrückt, bis die Kontrolllampen , , und blinken und das Display nichts anzeigt. 2. Drücken Sie . • Die Kontrolllampen , 31 und erlöschen.
www.aeg.com • Die Kontrolllampen , und erlöschen. • Die Kontrolllampe blinkt weiter. • Im Display wird die aktuelle 3. Drücken Sie Einstellung. zum Ändern der = Signalton ist eingeschaltet. 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. Einstellung angezeigt: = Signalton ist ausgeschaltet. 7. OPTIONEN Sie müssen die gewünschten Optionen vor dem Programmstart einschalten. Es ist nicht möglich, Optionen während eines laufenden Programms einoder auszuschalten.
DEUTSCH Ist die Option nicht mit dem Programm kombinierbar, leuchtet die entsprechende Kontrolllampe nicht oder sie blinkt ein paar Sekunden schnell und erlischt dann. 33 Das Display zeigt die aktualisierte Programmdauer an. 8. VOR DER ERSTEN INBETRIEBNAHME 1. Prüfen Sie, ob die Einstellung des Wasserenthärters der Wasserhärte in Ihrem Gebiet entspricht. Wenn nicht, stellen Sie die Wasserenthärterstufe ein. 2. Füllen Sie den Salzbehälter. 3. Füllen Sie den KlarspülmittelDosierer. 4.
www.aeg.com 8.2 Füllen des KlarspülmittelDosierers A B Tuch auf, um zu große Schaumbildung zu vermeiden. 4. Schließen Sie den Deckel. Achten Sie darauf, dass der Deckel einrastet. Füllen Sie den Klarspülmittel-Dosierer auf, wenn die Füllstandsanzeige für den Klarspüler (A) durchsichtig wird. Wenn Sie MultiReinigungstabletten verwenden und die Trocknungsleistung zufriedenstellend ist, kann die Klarspülernachfüllanzeige ausgeschaltet werden.
DEUTSCH ACHTUNG! Verwenden Sie nur Reinigungsmittel für Geschirrspüler. 1. Drücken Sie die Entriegelungstaste (A), um den Deckel (C) zu öffnen. 2. Füllen Sie das Reinigungsmittel ein oder legen Sie eine Reinigungstablette in den Behälter (B). 3. Wenn das Programm einen Vorspülgang hat, schütten Sie eine kleine Menge Reinigungsmittel auf die Innenseite der Gerätetür. 4. Schließen Sie den Deckel. Achten Sie darauf, dass der Deckel einrastet. 9.
www.aeg.com Bevor Sie ein neues Programm starten, stellen Sie sicher, dass der Reinigungsmittelbehälter gefüllt ist. Schließen Sie den Wasserhahn. Programmende Wenn das Programm beendet ist und Sie die Tür öffnen, schaltet sich das Gerät automatisch aus. 10. TIPPS UND HINWEISE 10.1 Allgemeines Die folgenden Hinweise stellen optimale Reinigungs- und Trocknungsergebnisse im täglichen Gebrauch sicher, und tragen auch zum Umweltschutz bei.
DEUTSCH kein Reinigungsmittel und beladen Sie die Körbe nicht. 4. Stellen Sie den Wasserenthärter nach Ablauf des Programms auf die Wasserhärte in Ihrer Region ein. 5. Stellen Sie die Menge des Klarspülmittels ein. 6. Schalten Sie den KlarspülmittelDosierer ein. 10.4 Beladen der Körbe • Spülen Sie im Gerät nur spülmaschinenfestes Geschirr. • Spülen Sie im Gerät keine Geschirrteile aus Holz, Horn, Aluminium, Zinn oder Kupfer.
www.aeg.com C B A 1. Drehen Sie den Filter (B) nach links und nehmen Sie ihn heraus. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 4. Reinigen Sie die Filter. 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein. Stellen Sie sicher, dass er korrekt unter den beiden Führungen eingesetzt wurde. 7.
DEUTSCH 39 ACHTUNG! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 11.2 Reinigen des oberen Sprüharms Wir empfehlen den oberen Sprüharm regelmäßig zu reinigen, um zu verhindern, dass Verunreinigungen die Löcher verstopfen. Verstopfte Löcher können die Ursache für nicht zufriedenstellende Spülergebnisse sein. 1. Ziehen Sie den Oberkorb bis zum Anschlag heraus. 2.
www.aeg.com Programme mit langer Laufzeit zu verwenden. • Um die Leistungsfähigkeit des Geräts zu erhalten, wird empfohlen einmal im Monat ein spezielles Reinigungsmittel für Geschirrspüler zu verwenden. Befolgen Sie sorgfältig die Anweisungen auf der Reinigungsmittelverpackung. 12. FEHLERSUCHE Das Gerät startet nicht oder bleibt während des Betriebs stehen.
DEUTSCH 41 Problem und Alarmcode Mögliche Ursachen und Abhilfe Das Gerät pumpt das Wasser nicht ab. • Vergewissern Sie sich, dass der Siphon nicht verstopft ist. • Vergewissern Sie sich, dass der Filter im Ablaufschlauch nicht verstopft ist. • Vergewissern Sie sich, dass das interne Filtersystem nicht verstopft ist. • Vergewissern Sie sich, dass der Ablaufschlauch nicht geknickt oder zu stark gekrümmt ist. Im Display erscheint . Das Wasserauslauf-Schutzsystem ist eingeschaltet.
www.aeg.com Siehe „Vor der ersten Inbetriebnahme“, „Täglicher Gebrauch“ oder „Tipps und Hinweise“ bezüglich anderer möglicher Ursachen. Problem erneut auf, wenden Sie sich an einen autorisierten Kundendienst. Wenden Sie sich an einen autorisierten Kundendienst, wenn Alarmcodes angezeigt werden, die nicht in der Tabelle angegeben sind. Schalten Sie nach der Überprüfung das Gerät aus und wieder ein. Tritt das 12.
DEUTSCH Störung 43 Mögliche Ursachen und Abhilfe Der Geräteinnenraum ist nass. • Dies ist keine Gerätestörung. Die Ursache ist die Luftfeuchtigkeit, die an den Wänden kondensiert. Ungewöhnliche Schaumbil• Verwenden Sie ausschließlich speziell für Geschirrspüdung während des Spülgangs. ler bestimmte Reinigungsmittel. • Der Klarspülmittel-Dosierer hat ein Leck. Wenden Sie sich an den autorisierten Kundendienst. Rostspuren am Besteck. • Das Spülwasser enthält zu viel Salz. Siehe „Wasserenthärter“.
www.aeg.com Wasserdruck bar (Mindest- und Höchstwert) 0.5 - 8 MPa (Mindest- und Höchstwert) 0.05 - 0.8 Fassungsvermögen Maßgedecke 15 Leistungsaufnahme Ein-Zustand (W) 0.99 Leistungsaufnahme Aus-Zustand (W) 0.10 1) Weitere Angaben finden Sie auf dem Typenschild. 14. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte.
DEUTSCH 45
www.aeg.
DEUTSCH 47
117896652-A-182015 www.aeg.