DE Benutzerinformation Geschirrspüler FAVORIT 78600 VI1P
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................... 4 3. GERÄTEBESCHREIBUNG...............................................................................................6 4. BEDIENFELD................................................................................................................... 7 5.
DEUTSCH 1. 3 SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.
www.aeg.com • • • • • • • • Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt. Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, seinem autorisierten Kundenservice oder einer gleichermaßen qualifizierten Person ausgetauscht werden, um Gefahrenquellen zu vermeiden. Stellen Sie Messer und Besteck mit scharfen Spitzen mit der Spitze nach unten in den Besteckkorb oder legen Sie sie waagerecht in das Gerät.
DEUTSCH • Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. • Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen. • Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose. Stellen Sie sicher, dass der Netzstecker nach der Montage noch zugänglich ist.
www.aeg.com 3. GERÄTEBESCHREIBUNG 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Oberster Sprüharm Oberer Sprüharm Unterer Sprüharm Filter Typenschild Salzbehälter Lüftungsschlitze 3.1 Beam-on-Floor Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Küchenboden projiziert wird. • Nach dem Start des Programms leuchtet der rote Lichtstrahl auf und bleibt während der gesamten Programmdauer eingeschaltet.
DEUTSCH 4. BEDIENFELD 1 1 2 3 4 5 2 3 Taste „Ein/Aus“ Display Taste Delay Taste Program Taste ExtraHygiene 4 6 7 8 9 5 6 7 8 9 Taste TimeSaver Taste XtraDry Taste RESET Kontrolllampen 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe Programmende. Kontrolllampe Salz. Sie erlischt während des Programmbetriebs. Kontrolllampe Klarspülmittel. Sie erlischt während des Programmbetriebs. 5.
www.aeg.
DEUTSCH Wasser (l) Energieverbrauch (kWh) Dauer (Min.) P2 7 - 14 0.6 - 1.4 40 - 150 P3 12.5 - 14.5 1.4 - 1.6 154 - 164 P4 12 - 14 0.7 - 0.9 75 - 85 P5 9.5 - 10.5 1.10 - 1.30 55 - 65 P6 10 0.9 30 P7 4 0.1 14 P8 9 - 10 1.0 - 1.2 219 - 229 Programm 1) 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.
www.aeg.com können Sie den Programmwahlmodus folgendermaßen einstellen: wird in gleichwertigen Einheiten gemessen. Halten Sie RESET gedrückt, bis sich das Gerät im Programmwahlmodus befindet. Der Enthärter muss entsprechend der Wasserhärte in Ihrem Gebiet eingestellt werden. Ihr lokales Wasserwerk kann Sie über die Wasserhärte in Ihrem Gebiet informieren. Der Wasserenthärter muss unbedingt auf die richtige Stufe eingestellt werden, um gute Spülergebnisse zu garantieren. 6.
DEUTSCH • Die Kontrolllampen , und erlöschen. Einstellung angezeigt: Z.B. Stufe 5. = 3. Drücken Sie wiederholt, um die Einstellung zu ändern. 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. 6.3 Klarspülmittel-Dosierer Klarspülmittel ermöglichen das Trocknen des Geschirrs ohne Streifen und Flecken. Das Klarspülmittel wird automatisch während der heißen Spülphasen abgegeben. 6.
www.aeg.com So schalten Sie den Signalton für das Programmende ein Das Gerät muss sich im Programmwahlmodus befinden. Einstellung angezeigt: = Signalton ist ausgeschaltet. 1. Halten Sie zum Aufrufen des Benutzermodus gleichzeitig • Die Kontrolllampe blinkt weiter. • Im Display wird die aktuelle und gedrückt, bis die Kontrolllampen , , und blinken und das Display nichts anzeigt. 3. Drücken Sie Einstellung. zum Ändern der = Signalton ist eingeschaltet. 4.
DEUTSCH Das Display zeigt die aktualisierte Programmdauer an. 7.3 ExtraHygiene Diese Option sorgt für hygienischere Ergebnisse. Während der letzten Spülphase wird die Temperatur für mindestens 10 Minuten auf 70 °C gehalten. 13 Ist die Option nicht mit dem Programm kombinierbar, leuchtet die entsprechende Kontrolllampe nicht oder sie blinkt ein paar Sekunden schnell und erlischt dann. Das Display zeigt die aktualisierte Programmdauer an.
www.aeg.com Beim Befüllen des Salzbehälters können Wasser und Salz austreten. Korrosionsgefahr. Starten Sie ein Programm, nachdem Sie den Salzbehälter befüllt haben, um die Korrosion zu vermeiden. 1. Öffnen Sie den Deckel (C). 2. Füllen Sie den Dosierer (B) mit Klarspülmittel bis zur Marke „MAX“. 3. Wischen Sie verschüttetes Klarspülmittel mit einem saugfähigen Tuch auf, um zu große Schaumbildung zu vermeiden. 4. Schließen Sie den Deckel. Achten Sie darauf, dass der Deckel einrastet.
DEUTSCH ACHTUNG! Verwenden Sie nur Reinigungsmittel für Geschirrspüler. 1. Drücken Sie die Entriegelungstaste (A), um den Deckel (C) zu öffnen. 2. Füllen Sie das Reinigungsmittel ein oder legen Sie eine Reinigungstablette in den Behälter (B). 3. Wenn das Programm einen Vorspülgang hat, schütten Sie eine kleine Menge Reinigungsmittel auf die Innenseite der Gerätetür. 4. Schließen Sie den Deckel. Achten Sie darauf, dass der Deckel einrastet. 9.
www.aeg.com Beenden des Programms Programmende Halten Sie RESET gedrückt, bis sich das Gerät im Programmwahlmodus befindet. Bevor Sie ein neues Programm starten, stellen Sie sicher, dass der Reinigungsmittelbehälter gefüllt ist. Wenn das Programm beendet ist und Sie die Tür öffnen, schaltet sich das Gerät automatisch aus. Schließen Sie den Wasserhahn. 10. TIPPS UND HINWEISE 10.
DEUTSCH kein Reinigungsmittel und beladen Sie die Körbe nicht. 4. Stellen Sie den Wasserenthärter nach Ablauf des Programms auf die Wasserhärte in Ihrer Region ein. 5. Stellen Sie die Menge des Klarspülmittels ein. 10.4 Beladen der Körbe • Spülen Sie im Gerät nur spülmaschinenfestes Geschirr. • Spülen Sie im Gerät keine Geschirrteile aus Holz, Horn, Aluminium, Zinn oder Kupfer. • Spülen Sie in diesem Gerät keine Gegenstände, die Wasser aufnehmen können (Schwämme, Geschirrtücher usw.).
www.aeg.com C B A 1. Drehen Sie den Filter (B) nach links und nehmen Sie ihn heraus. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 4. Reinigen Sie die Filter. 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein. Stellen Sie sicher, dass er korrekt unter den beiden Führungen eingesetzt wurde. 7.
DEUTSCH 19 ACHTUNG! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 11.2 Reinigen des oberen Sprüharms Wir empfehlen den oberen Sprüharm regelmäßig zu reinigen, um zu verhindern, dass Verunreinigungen die Löcher verstopfen. Verstopfte Löcher können die Ursache für nicht zufriedenstellende Spülergebnisse sein. 1. Ziehen Sie den Oberkorb bis zum Anschlag heraus. 2.
www.aeg.com Programme mit langer Laufzeit zu verwenden. • Um die Leistungsfähigkeit des Geräts zu erhalten, wird empfohlen einmal im Monat ein spezielles Reinigungsmittel für Geschirrspüler zu verwenden. Befolgen Sie sorgfältig die Anweisungen auf der Reinigungsmittelverpackung. 12. FEHLERSUCHE Das Gerät startet nicht oder bleibt während des Betriebs stehen.
DEUTSCH 21 Problem und Alarmcode Mögliche Ursachen und Abhilfe Das Gerät pumpt das Wasser nicht ab. • Vergewissern Sie sich, dass der Siphon nicht verstopft ist. • Vergewissern Sie sich, dass der Filter im Ablaufschlauch nicht verstopft ist. • Vergewissern Sie sich, dass das interne Filtersystem nicht verstopft ist. • Vergewissern Sie sich, dass der Ablaufschlauch nicht geknickt oder zu stark gekrümmt ist. Im Display erscheint . Das Wasserauslauf-Schutzsystem ist eingeschaltet.
www.aeg.com Siehe „Vor der ersten Inbetriebnahme“, „Täglicher Gebrauch“ oder „Tipps und Hinweise“ bezüglich anderer möglicher Ursachen. Problem erneut auf, wenden Sie sich an einen autorisierten Kundendienst. Wenden Sie sich an einen autorisierten Kundendienst, wenn Alarmcodes angezeigt werden, die nicht in der Tabelle angegeben sind. Schalten Sie nach der Überprüfung das Gerät aus und wieder ein. Tritt das 12.
DEUTSCH 23 Störung Mögliche Ursachen und Abhilfe Das Geschirr ist nass. • Schalten Sie die Option XtraDry ein, um die beste Trocknungsleistung zu erzielen. • Das Programm enthält keine Trocknungsphase oder eine Trocknungsphase mit niedriger Temperatur. • Der Klarspülmittel-Dosierer ist leer. • Die Ursache kann in der Qualität des Klarspülmittels liegen. • Die Ursache kann in der Qualität der Multi-Reinigungstabletten liegen.
www.aeg.com Siehe „Vor der ersten Inbetriebnahme“, „Täglicher Gebrauch“ oder „Tipps und Hinweise“ bezüglich anderer möglicher Ursachen. 13. TECHNISCHE DATEN Abmessungen Breite/Höhe/Tiefe (mm) 596 / 818-898 / 550 Elektrischer Anschluss 1) Spannung (V) 200 - 240 Frequenz (Hz) 50 / 60 bar (Mindest- und Höchstwert) 0.5 - 8 MPa (Mindest- und Höchstwert) 0.05 - 0.8 Wasserversorgung Kalt- oder Warmwasser2) max. 60 °C Fassungsvermögen Maßgedecke 13 Leistungsaufnahme Ein-Zustand (W) 0.
DEUTSCH 25
www.aeg.
DEUTSCH 27
117907873-A-162015 www.aeg.