FAVORIT 88089 EN DISHWASHER USER MANUAL
FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it.
Contents 3 CONTENTS 4 6 8 11 11 13 13 15 15 17 19 21 23 26 26 30 33 33 34 Safety information Product description Control panel Use of the appliance Setting the water softener Use of dishwasher salt Use of detergent and rinse aid Multitab function Loading cutlery and dishes Washing programs Setting and starting a washing program Care and cleaning What to do if… Technical data Installation Water connection Electrical connection Environment concerns Warranty The following symbols are used in this user manu
Safety information SAFETY INFORMATION For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance. Correct use • Only use the appliance to clean household utensils that are suitable for dishwashers. • Do not put solvents in the appliance. Risk of explosion.
Safety information 5 Child safety • Do not let persons, children included, with reduced physical sensory, reduced mental functions or lack of experience and knowledge use the appliance. They must have supervision or instruction for the operation by a person who is responsible for their safety. • Children should be supervised to ensure that they do not play with the appliance. • Keep all the packaging away from children. There is a risk of suffocation. • Keep all detergents in a safe area.
Product description PRODUCT DESCRIPTION 10 1 9 2 3 4 5 1 2 3 4 5 6 7 8 9 10 8 7 6 Upper basket Air vent and water hardness dial Salt container Detergent dispenser Rinse aid dispenser Rating plate Filters Lower spray arm Upper spray arm Top spray arm Internal light This appliance has an internal light that comes on when you open the door and goes off when the door is closed. If it is necessary to replace the light, contact your local Customer Care Centre.
Product description TimeBeam The TimeBeam shows, on the kitchen floor, the time of the washing program or the countdown of the delay start. With the TimeBeam you always know the remaining time of the washing program and/or of the delay start. Nine different colours are available for TimeBeam (refer to ‘Control panel’). The TimeBeam shows: • The time of the washing program. It decreases with steps of one minute. • The end of the washing programme. A zero shows on the kitchen floor.
Control panel CONTROL PANEL The controls are on the top of the control panel. To operate with the controls keep the appliance door ajar. 1 1 2 3 4 5 6 7 8 9 2 3 4 5 6 7 8 9 On/off button Display Delay start touchpad Program touchpad Extra-Hygiene touchpad ÖKO PLUS touchpad Multitab touchpad RESET touchpad Indicators Indicators Salt indicator. It comes on when it is necessary to fill the salt container. 1) After you fill the container, the salt indicator can stay on for some hours.
Control panel • • • • • 9 The end of a washing program (the display shows a zero) The time of the delay start The alarm codes The activation and deactivation of the acoustic signals. The setting of the colour of the TimeBeam. Delay start touchpad Press this touchpad to delay the start of the washing program from 1 to 24 hours. Refer to 'Setting and starting a washing program'. Program touchpad Press this touchpad repeatedly to set a washing program.
Control panel • To deactivate or activate the acoustic signals. • To set the colour of the TimeBeam. Switch on the appliance. The appliance is in setting mode when: • The display shows two horizontal status bars. Switch on the appliance. The appliance is not in setting mode when: • The display shows the time of the washing program or of the delay start. – To go back to the setting mode, it is necessary to cancel the program or the delay start. Refer to 'Setting and starting a washing program'.
Use of the appliance 11 • The display shows a number followed by the letter C. On the floor you can see the colour that is related to the number. 5. Press touchpad (6) again and again to change the colour. Each time you press touchpad (6), the number in the display and the colour on the floor change (0C = TimeBeam decativated).) 6. Switch off the appliance to confirm. USE OF THE APPLIANCE Refer to the specific instructions for each step of the procedure. 1.
Setting the water softener Water hardness Water hardness setting mg/l ppm mmol/l manually electronically 260 - 329 260 - 329 2.6 - 3.2 1 4 190 - 259 190 - 259 1.9 - 2.5 1 3 70 - 189 70 - 189 0.7 - 1.8 1 2 < 70 < 70 < 0.7 1 11) 1) No use of salt required. You must set the water softener manually and electronically. Manual adjustment The appliance is set at the factory at position 2. 1. Remove the lower basket. 2.
Use of dishwasher salt 13 USE OF DISHWASHER SALT CAUTION! Only use dishwasher salt. Types of salt that are not suitable for dishwashers cause damage to the water softener. CAUTION! Grains of salt and salty water on the bottom of the appliance can cause corrosion. Fill the appliance with salt before you start a washing program. Filling the salt container 1. Turn the cap counterclockwise to open the salt container. 2. Fill the salt container with 1 litre of water (only the first operation). 3.
Use of detergent and rinse aid Use of detergent CAUTION! Only use detergents (powder, liquid or tablet) that are suitable for dishwashers. Follow the recommendations on the detergent packaging for the use and storage of the detergent. To help the environment, do not use more than the correct quantity of detergent. Filling with detergent 1. Press the release button 2 to open the lid 7 of the detergent dispenser. 2. Put the detergent in the dispenser 1 . 3.
Multitab function 15 MULTITAB FUNCTION The multitab function is for combi detergent tablets. These tablets contain agents as detergent, rinse aid and dishwasher salt. Some types of tablets can contain other agents. Be sure that these tablets are suitable for the water hardness in your area (refer to the instructions on the packaging of the products). The multitab function deactivates the flow of rinse aid and salt. The multitab function deactivates the indicators of salt and rinse aid.
Loading cutlery and dishes – Make sure that cutlery and dishes do not lie inside one another. – Make sure that cutlery and dishes do not cover other cutlery and dishes. – Make sure that glasses do not touch other glasses. – Put small objects in the cutlery basket. • Plastic items and pans with non-stick coatings can retain water droplets. Plastic items do not dry as well as porcelain and steel items. • Put light items in the upper basket. Make sure that the items do not move.
Washing programs 17 WASHING PROGRAMS Program 1 Type of soil Type of load Program description Functions All Crockery, cutlery, pots and pans Prewash Wash 45 °C or 70 °C Rinses Dry Extra-Hygiene ÖKO PLUS 2 Heavy soil Crockery, cutlery, pots and pans Prewash Wash 70 °C Rinses Dry ÖKO PLUS 3 Normal soil Crockery and cutlery Prewash Wash 50 °C Rinses Dry Fresh soil Crockery and cutlery Wash 60 °C Rinse Extra-Hygiene Normal soil Crockery and cutlery Prewash Wash 50 °C Rinses Dry Extra-H
Washing programs 4) This is the standard program for test institutes. With this program you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. Refer to the supplied leaflet for test information. 5) With this program you can wash a load with mixed soil. Very heavy soil in the lower basket and normal soil in the upper basket. The water pressure in the lower basket is three times higher than in the upper basket.
Setting and starting a washing program 19 SETTING AND STARTING A WASHING PROGRAM Starting the washing program without delay start 1. Switch on the appliance. Make sure that the appliance is in setting mode. 2. Set the washing program. The number related to the washing program flashes in the display. 3. If you want, set the Extra-Hygiene and/or the ÖKO PLUS function. Set these functions after the setting of the washing program 4. Close the appliance door, the washing program starts.
Setting and starting a washing program Interrupting a washing program • Open the appliance door. The washing program stops. • Close the appliance door. The washing program continues from the point of interruption. Cancelling the washing program If the washing program has not started, you can change the selection. To change the selection while the washing program operates, it is necessary to cancel the program. • Press the RESET touchpad until the display shows two horizontal status bars.
Care and cleaning 21 CARE AND CLEANING To remove and clean the filters WARNING! Switch the appliance off before you carry out any cleaning operation. Dirty filters decrease the washing results. Although the maintenance is very low with these filters, we recommend that you regularly check the filters and clean them if necessary. 1. To remove filter (A), turn it counterclockwise and remove it out from filter (B). B A 2. Filter (A) has 2 parts. To disassemble the filter, pull them apart. 3.
Care and cleaning Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms become clogged, remove remaining parts of soil with a thin pointed object. External cleaning Clean the external surfaces of the appliance and control panel with a damp soft cloth. Only use neutral detergents. Do not use abrasive products, scouring pads or solvents (e.g. acetone). Internal cleaning We recommend, every 3 months to run a washing program for heavily soiled dishes.
What to do if… 23 WHAT TO DO IF… The appliance does not start or stops during operation. If there is a fault, first try to find a solution to the problem yourself. Refer to following charts. If you cannot find a solution to the problem, contact your dealer or the Customer Care Centre. With some malfunctions, the display shows an alarm code: - The appliance does not fill with water • - The appliance does not drain the water • - The anti-flood device operates.
What to do if… If the display shows an alarm code, not described in the chart, contact your Customer Care Centre. When you contact the Customer Care Centre you will need to give some details of the appliance that can be found on the rating plate (e.g. model number, serial number, product number). We recommend that you record these details. The washing results and drying results are not satisfactory Problem The dishes are not clean.
What to do if… Problem Possible cause 25 Possible solution The multitab function is activa- Activate the rinse aid dispenser. ted (this function automatically deactivates the rinse aid dispenser). Activating the rinse aid dispenser 1. Switch on the appliance. Make sure that the appliance is in setting mode. 2. Press and hold touchpad (4) and touchpad (5) at the same time until the indicators of touchpads (3), (4), (5) and (6) flash. 3. Release touchpad (4) and touchpad (5). 4. Press touchpad (4).
Technical data TECHNICAL DATA Dimensions Width Height Depth Electrical connection Voltage Overall power Fuse Frequency Water supply pressure min. max.
Installation 27 The appliance has adjustable feet to allow the adjustment of its height. Make sure that the water inlet hose, the drain hose and the mains cable are not bent or squashed, when you insert the appliance. Adhesive steam protection foil Fit the steam protection on the front part of the kitchen counter along the entire width. 600 mm Adjusting the height of the appliance 1. Remove the adjustable plinth. 2. – To lift the front of the appliance, turn the two front feet counterclockwise.
Installation Installing the appliance under the kitchen counter or to adjacent units WARNING! To prevent injury or damage, make sure that the appliance is secured adjacent safe structures. The appliance is provided with six fixing points: • Two external brackets • Four internal fixing points. Use the external brackets when installing the appliance under the kitchen counter or to the adjacent units or if the opening for the appliance is greater than 600 mm.
Installation We recommend that you make a custom made kick-panel that aligns your kitchen cabinets. A notched continuous panel is necessary to prevent door swing interference and to keep kickpanel alignment with adjacent units. 1. Cut a notch in the kick-panel sufficient to let the door swing freely under the appliance (refer to the chart). 2. Make a check for interference. Open and close the door slowly. If the door touches the kickpanel, trim to prevent interference. 3.
Water connection WATER CONNECTION Water inlet hose Connect the inlet hose to a water tap with an external BSP thread spout of 3/4”. For best washing performance it is recommended to connect the appliance to a cold water supply. Energy savings can be made by connecting the appliance to a Solar water system and using economy options, however the water temperature must not exceed 60 °C. Once connected the inlet hose to the water tap, turn the tap on and check that there are no leaks.
Water connection 31 WARNING! Dangerous voltage In order to pass the safety valve through the kitchen cabinets, an opening of at least 45 mm x 90 mm is needed. Water drain hose Use the supplied hose clamp to connect the water drain hose to the sink. The highest point of the drain hose must be no more than 600 mm from the floor and must have a continuous fall to the plumbing connection. The drain hose can be lengthened using additional lengths and connectors.
Water connection If you connect the water drain hose to a trap spigot under the sink, remove the plastic membrane. If you do not remove the membrane, remaining food can cause a blockage in the drain hose spigot. The appliance has a security feature to prevent dirty water going back into the appliance. If, the spigot of the sink has a 'non-return valve', this valve can cause the appliance to drain incorrectly. Remove the non-return valve.
Electrical connection 33 ELECTRICAL CONNECTION WARNING! • The manufacturer accepts no liability for failure to observe the below safety precautions. • Safety standards require the appliance to be earthed. • Prior to using the appliance for the first time, ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. • The fuse rating can be found on the rating plate and in 'Technical data'.
Warranty WARRANTY FOR SALES IN AUSTRALIA AND NEW ZEALAND ALL AEG BRANDED APPLIANCES This document sets out the terms and conditions of the product warranties for AEG Appliances. It is an important document. Please keep it with your proof of purchase documents in a safe place for future reference should you require service for your Appliance. 1.
Warranty 5. 35 You will bear the cost of transportation, travel and delivery of the Appliance to and from AEG or its ASC.
12. For Appliances and services provided by AEG in New Zealand, the Appliances come with a guarantee by AEG pursuant to the provisions of the Consumer Guarantees Act, the Sale of Goods Act and the Fair Trading Act. 13.
www.aeg.
