CS PL Návod k použití Myčka nádobí Instrukcja obsługi Zmywarka 2 21 FAVORIT 88702 VI0P
www.aeg.com OBSAH 1. BEZPEČNOSTNÍ INFORMACE......................................................................... 3 2. BEZPEČNOSTNÍ POKYNY................................................................................4 3. POPIS SPOTŘEBIČE.........................................................................................6 4. OVLÁDACÍ PANEL.............................................................................................7 5. PROGRAMY....................................................
ČESKY 1. 3 BEZPEČNOSTNÍ INFORMACE Tento návod si pečlivě přečtěte ještě před instalací spotřebiče a jeho prvním použitím. Výrobce nezodpovídá za škody a zranění způsobená nesprávnou instalací či chybným používáním. Návod k použití vždy uchovávejte spolu se spotřebičem pro jeho budoucí použití. 1.
www.aeg.com • Spotřebič musí být připojen k vodovodnímu potrubí pomocí nové dodané soupravy hadic. Neinstalujte již jednou použitou soupravu hadic znovu. 1.
ČESKY 2.3 Vodovodní přípojka 2.4 Použití spotřebiče • • • • • Dbejte na to, abyste hadice nepoškodili. Před připojením spotřebiče k novým hadicím nebo k hadicím, které nebyly dlouho používané, nechte vodu na několik minut odtéct, dokud nebude čistá. Při prvním použití spotřebiče se ujistěte, že nedochází k únikům vody. Přívodní hadice s opláštěním je vybavena bezpečnostním ventilem a vnitřním síťovým kabelem. • • • • • Na otevřená dvířka si nesedejte, ani si na ně nestoupejte.
www.aeg.com 3. POPIS SPOTŘEBIČE 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Nejvyšší ostřikovací rameno Horní ostřikovací rameno Dolní ostřikovací rameno Filtry Typový štítek Zásobník na sůl Větrací otvor 3.1 Beam-on-Floor Optická signalizace Beam-on-Floor promítá světlo na kuchyňskou podlahu pod dvířky spotřebiče. • • Když se spustí program, rozsvítí se červené světlo a zůstane svítit po celý průběh programu. Po dokončení programu se rozsvítí zelené světlo.
ČESKY 4. OVLÁDACÍ PANEL 1 1 2 3 4 5 2 3 Tlačítko Zap/Vyp Displej Dotykové tlačítko Delay Dotykové tlačítko Program Dotykové tlačítko ExtraHygiene 4 6 7 8 9 5 6 7 8 9 Dotykové tlačítko TimeSaver Dotykové tlačítko Multitab Dotykové tlačítko RESET Kontrolky 4.1 Kontrolky Kontrolka Popis Kontrolka konce programu. Kontrolka množství soli. Nikdy v průběhu programu nesvítí. Kontrolka stavu leštidla. Nikdy v průběhu programu nesvítí. 5.
www.aeg.
ČESKY Voda (l) Energie (kWh) Délka (min) P4 12.5 - 14.5 1.4 - 1.6 154 - 164 P5 12 - 14 0.7 - 0.9 75 - 85 P6 9.5 - 10.5 1.10 - 1.30 55 - 65 P7 10 0.9 30 P8 4 0.1 14 Program 1) 9 1) Hodnoty se mohou měnit v závislosti na tlaku a teplotě vody, na kolísání v dodávce proudu, na zvole‐ ných funkcích a na množství nádobí. 5.2 Informace pro zkušebny Pro všechny potřebné informace ohledně testu výkonnosti zašlete e-mail na: Poznamenejte si výrobní číslo (PNC) uvedené na typovém štítku.
www.aeg.com Čím je obsah těchto minerálů vyšší, tím je voda tvrdší. Tvrdost vody se označuje v ekvivalentních stupních tvrdosti. Tvrdost vody v místě vašeho bydliště zjistíte u místního vodárenského podniku. K zajištění dobrých výsledků mytí je důležité nastavit správný stupeň změkčovače vody. Změkčovač by měl být nastaven podle tvrdosti vody v místě vašeho bydliště.
ČESKY kontrolky , , a prázdným displejem. 2. Stiskněte s . • Kontrolky • • dále bliká. Kontrolka Na displeji se zobrazí aktuální , a zhasnou. nastavení: např. = stupeň 4. – Množství leštidla je v rozmezí 0A až 6A. – Stupeň 0 = neuvolňuje se žádné leštidlo. 3. Opětovným stisknutím změňte nastavení. 4. Potvrďte nastavení stisknutím tlačítka Zap/Vyp. 6.4 Použití leštidla spolu s kombinovanými mycími tabletami Dávkovač leštidla je z výroby nastaven jako zapnutý.
www.aeg.com 7. FUNKCE Před spuštěním programu je nutné pokaždé navolit požadované funkce. Během spuštěného programu již není možné funkce vypnout či zapnout. Ne všechny funkce jsou vzájemně slučitelné. Pokud zvolíte neslučitelné funkce, spotřebič automaticky jednu nebo více z nich vypne. Zůstanou svítit pouze ukazatele těch funkcí, které jsou stále zapnuty. 7.1 Multitab Tuto funkci zapněte, když používáte kombinované mycí tablety, které obsahují sůl, leštidlo a mycí prostředek.
ČESKY Nepoužívejte mycí prostředek a nevkládejte nic do košů. Při spuštění programu může spotřebiči trvat až pět minut, než se zregeneruje pryskyřice ve změkčovači vody. Během této chvíle spotřebič vypadá, že nepracuje. Mycí fáze se spustí až po dokončení této procedury. Tato procedura se pravidelně opakuje. 8.1 Zásobník na sůl POZOR! Používejte pouze sůl pro myčky nádobí. 13 5. Zavřete zásobník na sůl otočením jeho víčka po směru hodinových ručiček.
www.aeg.com Zkontrolujte, zda je spotřebič v režimu volby programu. • Pokud kontrolka stavu soli svítí, doplňte zásobník na sůl. • Pokud kontrolka stavu leštidla svítí, doplňte dávkovač leštidla. 3. Naplňte koše. 4. Přidejte mycí prostředek. Pokud používáte kombinované mycí tablety, zapněte funkci Multitab. 5. Nastavte a spusťte správný program pro daný druh náplně a stupeň znečištění. 9.1 Použití mycího prostředku A B • • Po pěti minutách po dokončení programu.
ČESKY Zrušení odloženého startu během jeho odpočítávání Když zrušíte odložený start, musíte opět nastavit program a jeho funkce. 1. Otevřete dvířka spotřebiče. 2. Stisknutím tlačítka Zap/Vyp spotřebič vypněte. 3. Spotřebič nechte vypnutý přibližně 30 sekund. 4. Opětovným stisknutím tlačítka Zap/Vyp zapněte spotřebič. 5. Stiskněte a podržte RESET, dokud se spotřebič nepřepne do režimu volby programu. Zrušení programu 1. Otevřete dvířka spotřebiče. 15 2. Stisknutím tlačítka Zap/Vyp spotřebič vypněte. 3.
www.aeg.com 10.3 Co dělat, pokud chcete přestat používat mycí tablety Než začnete odděleně používat mycí prostředek, sůl a leštidlo, proveďte následující postup. 1. Nastavte nejvyšší stupeň změkčovače vody. 2. Ujistěte se, že je zásobník na sůl a dávkovač leštidla plný. 3. Nastavte nejkratší program s oplachovací fází. Nepoužívejte mycí prostředek a nevkládejte nic do košů. 4. Po dokončení programu nastavte změkčovač vody na stupeň tvrdosti vody v místě vašeho bydliště. 5. Seřiďte dávkování leštidla.
ČESKY 17 C B A 1. Otočte filtrem (B) proti směru hodinových ručiček a vyndejte jej. 2. Vyndejte filtr (C) z filtru (B). 3. Vyjměte plochý filtr (A). 5. Zkontrolujte, zda ve sběrné jímce nebo kolem ní nejsou žádné zbytky jídel a nečistot. 6. Vložte zpět plochý filtr (A). Ujistěte se, že je správně umístěn pod dvěma vodicími drážkami. 7. Sestavte filtry (B) a (C). 8. Vložte zpět filtr (B) do plochého filtru (A). Otočte jím po směru hodinových ručiček, dokud se nezajistí. 4. Filtry omyjte.
www.aeg.com 11.2 Čištění ostřikovacích ramen 11.4 Čištění vnitřního prostoru Ostřikovací ramena nevyjímejte. Jestliže se otvory v ostřikovacích ramenech zanesou nečistotami, odstraňte je úzkým špičatým předmětem. • 11.3 Čištění vnějších ploch • • • Vyčistěte spotřebič vlhkým měkkým hadrem. Používejte pouze neutrální mycí prostředky. Nepoužívejte prostředky s drsnými částicemi, drátěnky nebo rozpouštědla. • Pečlivě očistěte spotřebič včetně pryžového těsnění dvířek vlhkým měkkým hadříkem.
ČESKY Po kontrole spotřebiče jej vypněte a znovu zapněte. Pokud se problém objeví znovu, obraťte se na autorizované servisní středisko. 19 Při výskytu výstražných kódů, které nejsou uvedené v tabulce, se obraťte na autorizované servisní středisko. 12.1 Nádobí není dostatečně umyté nebo suché Problém Možné řešení Na nádobí a skle jsou bílé šmouhy nebo modravý potah. • • Na sklenicích a nádobí jsou skvrny a zaschlé vodní kapky. • Nádobí je mokré.
www.aeg.com 14. POZNÁMKY K OCHRANĚ ŽIVOTNÍHO PROSTŘEDÍ Recyklujte materiály označené určené k likvidaci. Spotřebiče označené symbolem . Obaly vyhoďte do příslušných odpadních kontejnerů k recyklaci. Pomáhejte chránit životní prostředí a lidské zdraví a recyklovat elektrické a elektronické spotřebiče příslušným symbolem nelikvidujte spolu s domovním odpadem. Spotřebič odevzdejte v místním sběrném dvoře nebo kontaktujte místní úřad.
POLSKI 21 SPIS TREŚCI 1. INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA......................................... 22 2. WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA.......................................... 23 3. OPIS URZĄDZENIA......................................................................................... 25 4. PANEL STEROWANIA.....................................................................................26 5. PROGRAMY.............................................................................................
1. www.aeg.com INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA Przed instalacją i rozpoczęciem eksploatacji urządzenia należy uważnie zapoznać się z załączoną instrukcją obsługi. Producent nie odpowiada za uszkodzenia i obrażenia ciała spowodowane nieprawidłową instalacją i eksploatacją. Należy zachować instrukcję wraz z urządzeniem do wykorzystania w przyszłości. 1.
POLSKI • • 23 Wykładzina podłogowa nie może zasłaniać otworów wentylacyjnych w podstawie (jeśli dotyczy). Urządzenie należy podłączyć do instalacji wodociągowej za pomocą nowego zestawu węży dostarczonych w komplecie z urządzeniem. Nie wolno używać starego zestawu węży. 1.
www.aeg.com • • • • • • • tabliczce znamionowej są zgodne z parametrami instalacji zasilającej. W przeciwnym razie należy skontaktować się z elektrykiem. Należy używać wyłącznie prawidłowo zamontowanego gniazda elektrycznego z uziemieniem. Nie stosować rozgałęźników ani przedłużaczy. Należy zwrócić uwagę, aby nie uszkodzić wtyczki ani przewodu zasilającego. Wymiany przewodu zasilającego można dokonać wyłącznie w naszym autoryzowanym centrum serwisowym.
POLSKI • 25 Wymontować zatrzask drzwi, aby uniemożliwić zamknięcie się dzieci lub zwierząt w urządzeniu. 3. OPIS URZĄDZENIA 1 2 3 12 11 10 9 8 7 1 Najwyżej położone ramię spryskujące 2 Górne ramię spryskujące 3 Dolne ramię spryskujące 4 Filtry 5 Tabliczka znamionowa 6 Zbiornik soli 7 8 9 10 11 12 3.1 Beam-on-Floor • System Beam-on-Floor wyświetla wiązkę światła na podłodze kuchennej przed drzwiami urządzenia.
www.aeg.com 4. PANEL STEROWANIA 1 1 2 3 4 5 2 Przycisk wł./wył. Wyświetlacz Pole dotykowe Delay Pole dotykowe Program Pole dotykowe ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Pole dotykowe TimeSaver Pole dotykowe Multitab Pole dotykowe RESET Wskaźniki 4.1 Wskaźniki Wskaźnik Opis Wskaźnik zakończenia programu. Wskaźnik soli. W trakcie programu wskaźnik ten jest zawsze wyłączony. Wskaźnik płynu nabłyszczającego. W trakcie programu wskaźnik ten jest zawsze wyłączony. 5.
POLSKI Program Stopień zabrudze‐ Fazy programu nia Rodzaj załadunku Opcje P4 • • Duże Naczynia sto‐ łowe, sztućce, garnki i patelnie Zmywanie wstępne Zmywanie 70°C Płukania Suszenie • • TimeSaver Multitab • Średnie lub lekk‐ • ie • Delikatne naczy‐ • nia i szkło Zmywanie 45°C Płukania Suszenie • Multitab • • Lekkie Naczynia sto‐ łowe i sztućce • • Zmywanie 55°C Płukania • • ExtraHygiene Multitab • • Świeże Naczynia sto‐ łowe i sztućce • • Zmywanie 60°C Płukania • • ExtraHygiene Mul
www.aeg.com Zużycie wody (l) Zużycie energii (kWh) Czas trwania (min) P3 14 - 16 1.2 - 1.5 139 - 149 P4 12.5 - 14.5 1.4 - 1.6 154 - 164 P5 12 - 14 0.7 - 0.9 75 - 85 P6 9.5 - 10.5 1.10 - 1.30 55 - 65 P7 10 0.9 30 P8 4 0.1 14 Program1) 1) Parametry eksploatacyjne mogą ulec zmianie w zależności od ciśnienia i temperatury wody, zmian w napięciu zasilania, użytych opcji oraz ilości naczyń. 5.
POLSKI 6.2 Zmiękczanie wody 29 Zmiękczanie powinno być dostosowane do stopnia twardości wody doprowadzonej do urządzenia. W lokalnym zakładzie wodociągowym można uzyskać informację na temat twardości wody. Istotne jest ustawienie właściwego poziomu zmiękczania wody, aby zapewnić dobre rezultaty zmywania. Zmiękczacz usuwa z wody substancje mineralne, które mogą mieć negatywny wpływ na rezultaty zmywania lub na pracę urządzenia. Im wyższa zawartość substancji mineralnych, tym twardsza jest woda.
www.aeg.com Dozowanie płynu nabłyszczającego można ustawić w przedziale od 1 (minimalna ilość) do 6 (maksymalna ilość). Poziom 0 oznacza wyłączenie dozownika płynu nabłyszczającego oraz dozowania. Ustawienie fabryczne: poziom 4. Regulacja dozowania płynu nabłyszczającego 1. Aby uruchomić tryb użytkownika, nacisnąć jednocześnie i przytrzymać i , aż wskaźniki , , i zaczną migać, a wyświetlacz będzie pusty. 2. Nacisnąć . • Wskaźniki się. • • będzie nadal migał.
POLSKI Włączanie sygnału dźwiękowego zakończenia programu Urządzenie musi być w trybie wyboru programów. 1. Aby uruchomić tryb użytkownika, nacisnąć jednocześnie i przytrzymać przyciski i , aż wskaźniki , , i zaczną migać, a wyświetlacz będzie pusty. 2. Nacisnąć , i 31 • Wskaźniki się. • • Wskaźnik będzie nadal migał. Na wyświetlaczu pojawi się aktualne ustawienie: dźwiękowy wyłączony. wyłączą = sygnał 3. Nacisnąć , aby zmienić ustawienie. = sygnał dźwiękowy włączony. 4. Nacisnąć przycisk wł.
www.aeg.com 7.3 ExtraHygiene Ta opcja zapewnia większą higienę zmywania naczyń. Podczas ostatniej fazy płukania temperatura pozostaje na poziomie 70°C przez co najmniej 10 minut. Jeśli opcja nie jest dostępna w danym programie, jej wskaźnik nie zaświeca się lub miga przez kilka sekund, a następnie gaśnie. Wyświetlacz wyświetli zaktualizowany czas trwania programu. Włączanie opcji ExtraHygiene Nacisnąć przycisk – zaświeci się odpowiedni wskaźnik. 8. PRZED PIERWSZYM UŻYCIEM 1.
POLSKI 8.2 Napełnianie dozownika płynu nabłyszczającego A 33 UWAGA! Należy stosować wyłącznie płyn nabłyszczający przeznaczony do zmywarek. B 1. Otworzyć pokrywę (C). 2. Napełnić dozownik (B), aż poziom płynu nabłyszczającego osiągnie znak „MAX”. 3. Rozlany płyn nabłyszczający należy usunąć za pomocą chłonnej szmatki, aby zapobiec powstaniu zbyt dużej ilości piany. 4. Zamknąć pokrywę. Upewnić się, że pokrywa jest zablokowana.
www.aeg.com wewnętrznej stronie drzwi urządzenia. 4. Zamknąć pokrywę. Upewnić się, że pokrywa jest zablokowana. 9.2 Ustawianie i uruchamianie programu Funkcja Auto Off Funkcja ta służy do zmniejszenia zużycia energii elektrycznej przez automatyczne wyłączanie urządzenia, gdy nie jest ono używane. Funkcja uruchamia się: • Po upływie 5 minut od zakończenia programu. • Po upływie 5 minut, jeśli nie uruchomiono programu. Uruchamianie programu 1. Uchylić drzwi urządzenia. 2. Nacisnąć przycisk wł./wył.
POLSKI Koniec programu 35 Zakręcić zawór wody. Po zakończeniu programu i otworzeniu drzwi urządzenie jest automatycznie wyłączane. 10. WSKAZÓWKI I PORADY 10.1 Informacje ogólne • Stosowanie się do poniższych wskazówek pomoże zapewnić optymalne efekty prania i suszenia podczas codziennej eksploatacji oraz przyczyni się do ochrony środowiska. • • • • • • Większe resztki żywności z naczyń należy wyrzucić do kosza. Nie opłukiwać naczyń ręcznie.
www.aeg.com płynu nabłyszczającego należy wykonać poniższą procedurę. 1. Ustawić najwyższy poziom zmiękczania wody. 2. Upewnić się, że zbiornik soli oraz dozownik płynu nabłyszczającego są pełne. 3. Uruchomić najkrótszy program z fazą płukania. Nie dodawać detergentu ani nie umieszczać naczyń w koszach. 4. Po zakończeniu programu ustawić stopień zmiękczania wody odpowiednio do twardości wody doprowadzanej do urządzenia. 5. Wyregulować dozowanie płynu nabłyszczającego. • • 10.
POLSKI 37 C B A 1. Obrócić filtr (B) przeciwnie do ruchu wskazówek zegara i wyjąć go. 2. Wyjąć filtr (C) z filtra (B). 3. Wyjąć filtr płaski (A). 4. Umyć filtry. 5. Upewnić się, że wokół krawędzi osadnika nie znajdują się resztki żywności ani zanieczyszczenia. 6. Włożyć na miejsce filtr płaski (A). Upewnić się, że jest prawidłowo umieszczony pod 2 prowadnicami. 7. Włożyć filtry (B) i (C). 8. Włożyć filtr (B) do filtra płaskiego (A). Obrócić zgodnie z ruchem wskazówek zegara, aż się zablokuje.
www.aeg.com UWAGA! Nieprawidłowe umiejscowienie filtrów może skutkować niezadowalającymi efektami zmywania i uszkodzeniem urządzenia. 11.2 Czyszczenie ramion spryskujących Nie wolno wyjmować ramion spryskujących. Jeżeli otwory w ramionach spryskujących są zatkane, zabrudzenia należy usunąć przy pomocy cienkiego i zaostrzonego przedmiotu. 11.3 Czyszczenie obudowy • • • Używać wyłącznie neutralnych detergentów. Nie używać produktów ściernych, myjek do szorowania ani rozpuszczalników. 11.
POLSKI Problem i kod alarmowy Możliwe rozwiązanie Urządzenie nie napełnia się wodą. Na wyświetlaczu widoczne • • jest wskazanie . Urządzenie nie wypompo‐ wuje wody. Na wyświetlaczu widoczne jest wskazanie Sprawdzić, czy zawór wody jest otwarty. Upewnić się, że ciśnienie wody nie jest zbyt niskie. W tym celu należy skontaktować się z miejscowym za‐ kładem wodociągowym. Upewnić się, że zawór wody jest drożny. Upewnić się, że filtr w wężu dopływowym jest drożny.
www.aeg.com 13. DANE TECHNICZNE Wymiary Szerokość / wysokość / głębokość 596 / 818-898 / 550 (mm) Podłączenie do sieci elek‐ Napięcie (V) 220 - 240 trycznej 1) Częstotliwość (Hz) 50 Ciśnienie doprowadzanej wo‐ bar (minimalne i maksymalne) dy MPa (minimalne i maksymalne) 0.5 - 8 Dopływ wody Zimna lub ciepła woda 2) maks. 60°C Pojemność Liczba kompletów 15 Pobór mocy Tryb czuwania (W) 0.99 Pobór mocy Tryb wyłączenia (W) 0.10 0.05 - 0.
POLSKI 41
www.aeg.
POLSKI 43
117904081-A-342014 www.aeg.