NL EN FR Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 26 49 FAVORIT 88705 VI1P
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE.......................................................................................3 2. VEILIGHEIDSVOORSCHRIFTEN.............................................................................. 4 3. BESCHRIJVING VAN HET PRODUCT..................................................................... 6 4. BEDIENINGSPANEEL............................................................................................... 7 5. PROGRAMMA’S...........................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel en schade veroorzaakt door een foutieve installatie. Bewaar de instructies van het apparaat voor toekomstig gebruik. 1.
www.aeg.com • • • • • • gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen of stoom om het apparaat te reinigen.
NEDERLANDS gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Zorg dat u de waterslangen niet beschadigt. • Laat het water stromen tot het schoon is voordat u het apparaat aansluit op nieuwe leidingen of leidingen die lang niet zijn gebruikt. • Zorg dat er geen lekkages zijn als u het apparaat de eerste keer gebruikt. • De watertoevoerslang heeft een veiligheidsventiel en een omhulsel met een hoofdkabel aan de binnenkant.
www.aeg.com 3. BESCHRIJVING VAN HET PRODUCT 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Top sproeiarm Bovenste sproeiarm Onderste sproeiarm Filters Typeplaatje Zoutreservoir Luchtopening 3.1 TimeBeam De TimeBeam is een weergave die op de vloer onder de deur van het apparaat te zien is. • Wanneer het programma start, verschijnt de duur van het programma. • Wanneer het programma is voltooid, wordt 0:00 en CLEAN weergegeven. • Wanneer de uitgestelde start begint, wordt de aftelduur en DELAY zichtbaar.
NEDERLANDS 4. BEDIENINGSPANEEL 1 1 2 3 4 5 2 3 Aan/uit-toets Weergave Delay-tiptoets Program-tiptoets ExtraHygiene-tiptoets 4 6 7 8 9 5 6 7 8 9 TimeSaver-tiptoets XtraDry-tiptoets ProBoost-tiptoets Indicatielampjes 4.1 Indicatielampjes Aanduiding Beschrijving Einde-indicatielampje. XtraDry-indicatielampje. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Glansmiddelindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is.
www.aeg.
NEDERLANDS Programma Mate van vervuiling Type belading P9 • Normaal bevuild • Voorspoelen • Serviesgoed en • Wassen 50 °C bestek • Spoelingen • Drogen 7) Programmafasen 9 Opties • XtraDry 1) Dit programma biedt het meest efficiënte water- en energieverbruik voor normaal vervuild serviesgoed en bestek. (Dit is het standaard programma voor testinstituten). 2) Het apparaat detecteert de mate van vervuiling en de hoeveelheid serviesgoed in de korven.
www.aeg.com Water (l) Energie (kWh) Bereidingsduur (min) P7 10 0.9 30 P8 4 0.1 14 P9 9 - 10 1.0 - 1.2 219 - 229 Programma 1) 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.com Schrijf het productnummer (PNC) op dat u op het typeplaatje vindt. 6.
NEDERLANDS 11 Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
www.aeg.com Het instellen van het glansmiddelniveau • Het indicatielampje blijft knipperen. • Het display toont de huidige Het apparaat moet in de programmakeuzemodus staan. instelling: = het glansmiddeldoseerbakje is ingeschakeld (fabrieksinstelling). 1. Houd om de gebruikersmodus in te voeren tegelijkertijd en ingedrukt tot de indicatielampjes , . , • De indicatielampjes en , , 6.5 Geluidssignalen gaan uit. • Het indicatielampje blijft knipperen.
NEDERLANDS 6.6 De kleur instellen van de TimeBeam 4. Druk op de knop aan/uit om de instelling te bevestigen. Het apparaat moet in de programmakeuzemodus staan. 6.7 Het deactiveren van AutoOpen U kunt de kleur van de TimeBeam zodanig instellen, dat het mooi bij uw keuken aansluit. Er zijn verschillende kleuren beschikbaar. De TimeBeam kan ook worden uitgeschakeld. Het apparaat moet in de programmakeuzemodus staan. 1. Houd om de gebruikersmodus in te voeren tegelijkertijd 1.
www.aeg.com De optie XtraDry is geen permanente optie en moet elke cyclus geselecteerd worden. Het activeren van XtraDry Druk op . Het bijbehorende indicatielampje gaat branden. Als de optie niet van toepassing is op het programma, dan gaat het bijbehorende indicatielampje niet branden of het knippert even en gaat dan uit. Het display geeft de bijgewerkte programmaduur weer. 7.2 TimeSaver Met deze optie verhoogt u de druk en de temperatuur van het water. De wasen droogfasen zijn korter.
NEDERLANDS Deze optie wordt automatisch geactiveerd als u het programma instelt. Het is niet mogelijk om deze optie in te stellen bij andere programma's. Als u de optie AutoOpen wilt uitschakelen, gaat u naar "Instellingen". 15 In deze toestand wordt het energieverbruik van het programma verhoogd en vermindert het droogresultaat aanzienlijk. Ga om het droogresultaat te verbeteren naar optie XtraDry. 8. VOORDAT U HET APPARAAT VOOR DE EERSTE KEER GEBRUIKT 1.
www.aeg.com 8.2 Het vullen van het glansmiddeldoseerbakje A B 3. Verwijder gemorst glansmiddel met een absorberend doekje om te voorkomen dat er te veel schuim ontstaat. 4. Sluit het deksel. Zorg ervoor dat de deksel op zijn plaats dichtklikt. Vul het glansmiddeldoseerbakje bij wanneer de indicatie (A) helder wordt. Als u wastabletten gebruikt en u bent tevreden over het droogresultaat, kan de indicatie voor bijvullen van glansmiddel uitgeschakeld worden door het glasmiddelniveau op 0 te zetten.
NEDERLANDS LET OP! Gebruik uitsluitend vaatwasmiddelen die specifiek zijn bedoeld voor gebruik in vaatwassers 1. Druk op de ontgrendelknop (A) om de deksel te openen (C). 2. Doe de vaatwastablet of het poeder in het doseerbakje (B). 3. Plaats een kleine hoeveelheid van het vaatwasmiddel in de binnenkant van de deur van het apparaat als het programma een voorwasfase heeft. 4. Sluit het deksel. Zorg ervoor dat de deksel op zijn plaats dichtklikt. 9.
www.aeg.com Het programma annuleren 1. Open de deur van het apparaat. 2. Druk op de aan/uit-toets om het apparaat te deactiveren. 3. Houd het apparaat ongeveer 30 seconden uitgeschakeld. 4. Druk weer op de aan/uit-toets om het apparaat te activeren. 5. Houd en tegelijkertijd ingedrukt totdat het apparaat in de programmakeuzemodus staat. Controleer of er afwasmiddel in het afwasmiddeldoseerbakje aanwezig is voordat u een nieuw programma start.
NEDERLANDS 10.3 Wat moet u doen als u wilt stoppen met het gebruik van multitabletten Doe het volgende voordat u begint met het gebruiken van apart wasmiddel, zout en glansmiddel. 1. Stel het hoogste niveau van de waterontharder in. 2. Zorg ervoor dat het zout- en het glansmiddeldoseerbakje gevuld zijn. 3. Start het kortste programma met een spoelfase. Voeg geen afwasmiddel toe en ruim de mandjes niet in. 4. Als het programma is voltooid, wijzigt u de waterontharder in de waterhardheid van uw omgeving. 5.
www.aeg.com 11.1 De filters reinigen Het filtersystem bestaat uit 3 delen. C B A 1. Draai de filter (B) linksom en verwijder het. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter (A) terug. Zorg ervoor dat het goed onder de 2 geleidingen zit. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3.
NEDERLANDS 11.2 De sproeiarmen reinigen Probeer niet de sproeiarmen te verwijderen. Als etensresten de openingen in de sproeiarmen hebben verstopt, verwijder deze dan met een smal en puntig voorwerp. 11.3 Buitenkant reinigen • Maak het apparaat schoon met een vochtige, zachte doek. • Gebruik alleen neutrale schoonmaakmiddelen. • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen. 21 de deur, met een zachte, vochtige doek.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing Het apparaat neemt geen water. Op het display verschijnt • Controleer of de waterkraan is geopend. • Zorg dat de waterdruk niet te laag is. Neem hiervoor zo nodig contact op met uw lokale waterleidingbedrijf. • Controleer of de waterkraan niet verstopt is. • Controleer of het filter in de toevoerslang niet verstopt is. • Controleer of er geen knikken of bochten in de watertoevoerslang aanwezig zijn. .
NEDERLANDS 23 Probleem en alarmcode Mogelijke oorzaak en oplossing Het apparaat maakt kortsluiting. • De stroomsterkte is onvoldoende om alle tegelijk werkende apparaten van stroom te voorzien. Controleer de stroomsterkte van het stopcontact en het vermogen op de meter, of zet één van de in gebruik zijnde apparaten uit. • Interne elektrische storing van het apparaat. Neem contact op met een servicecentrum.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Het serviesgoed is nat. • Activeer voor de beste droogprestatie de optie XtraDry. • Het programma heeft geen droogfase of heeft een droogfase met lage temperatuur. • Het glansmiddeldoseerbakje is leeg. • De kwaliteit van het glansmiddel kan de oorzaak zijn. • De kwaliteit van de multitabletten kan de oorzaak zijn. Probeer een ander merk of activeer het glansmiddeldoseerbakje en gebruik het glansmiddel samen met de multitabletten.
NEDERLANDS 25 13. TECHNISCHE INFORMATIE Afmetingen Breedte / hoogte / diepte (mm) 596 / 818-898 / 550 Elektrische aansluiting 1) Voltage (V) 200 - 240 Frequentie (Hz) 50 / 60 bar (minimaal en maximaal) 0.5 - 8 MPa (minimaal en maximaal) 0.05 - 0.8 Watertoevoer Koud water of warm water2) max. 60 °C Vermogen Couverts 15 Energieverbruik Modus aan laten (W) 0.10 Energieverbruik Uit-modus (W) 0.10 Watertoevoerdruk 1) Zie het typeplaatje voor andere waarden.
www.aeg.com CONTENTS 1. SAFETY INFORMATION.........................................................................................27 2. SAFETY INSTRUCTIONS........................................................................................ 28 3. PRODUCT DESCRIPTION...................................................................................... 30 4. CONTROL PANEL...................................................................................................31 5. PROGRAMMES................
ENGLISH 1. 27 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com • • • • • • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
ENGLISH 29 • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. 2.5 Internal light WARNING! Risk of injury. WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Top spray arm Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 TimeBeam The TimeBeam is a display that shows on the floor below the appliance door. • When the programme starts, the programme duration comes on. • When the programme is completed, 0:00 and CLEAN come on. • When the delay start starts, the countdown duration and DELAY come on.
ENGLISH 4. CONTROL PANEL 1 1 2 3 4 5 2 On/off button Display Delay touchpad Program touchpad ExtraHygiene touchpad 3 4 6 7 8 9 5 6 7 8 9 TimeSaver touchpad XtraDry touchpad ProBoost touchpad Indicators 4.1 Indicators Indicator Description End indicator. XtraDry indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates. TimeSaver indicator. Delay indicator. ExtraHygiene indicator. ProBoost indicator. 5.
www.aeg.
ENGLISH Programme Degree of soil Type of load Programme phases Options P9 • Normal soil • Crockery and cutlery • • • • • XtraDry 7) Prewash Wash 50 °C Rinses Dry 33 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets .
www.aeg.com Water (l) Energy (kWh) Duration (min) P8 4 0.1 14 P9 9 - 10 1.0 - 1.2 219 - 229 Programme 1) 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes For all the necessary information for test performance, send an email to: info.test@dishwasher-production.com Write down the product number (PNC) that is on the rating plate. 6. SETTINGS 6.
ENGLISH 35 Water hardness German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
www.aeg.com 4. Press the on/off button to confirm the setting. and start to flash and the display is blank. 2. Press . • The indicators and , , 6.5 Acoustic signals , go off. • The indicator continues to flash. • The display shows the current setting: e.g. = level 4. – The levels of rinse aid are from 0A to 6A. – Level 0 = no rinse aid is released. again and again to change 3. Press the setting. 4. Press the on/off button to confirm the setting. 6.
ENGLISH the indicators , , , , and start to flash and the display is blank. 2. Press . • The indicators and , , , go off. continues to • The indicator flash. • The display shows a number and the letter C. Each number refers to a different colour. – = TimeBeam deactivated. again and again to change 3. Press the colour. • You can see the different colours on the kitchen floor. 4. Press the on/off button to confirm the setting. 37 1.
www.aeg.com The total programme duration decreases by approximately 50%. The display shows the updated programme duration. The washing results are the same as with the normal programme duration. The drying results can decrease. 7.5 AutoOpen How to activate TimeSaver Press This option improves the drying results with less energy consumption. , the related indicator comes on.
ENGLISH hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets. When you start a programme, the appliance can take up to 5 minutes to recharge the resin in the water softener. It seems that the appliance is not working.
www.aeg.com Fill the rinse aid dispenser when the indicator (A) becomes clear. If you use multi-tablets and the drying performance is satisfactory, the rinse aid refill indication can be disabled by setting the rinse aid level to 0. We recommend to always use rinse aid for better drying performance, also in combination with multitablets containing rinsing agent. 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance.
ENGLISH 41 The display will show the programme number for approximately 3 seconds and then show the programme duration. 4. Set the applicable options. 5. Close the appliance door to start the programme. Cancelling the delay start while the countdown operates Starting a programme with delay start 1. Open the appliance door. 2. Press the on/off button to deactivate the appliance. 3. Keep the appliance deactivated for approximately 30 seconds. 4. Press again the on/off button to activate the appliance.
www.aeg.com • You can use dishwasher detergent, rinse aid and salt separately or you can use the multi-tablets (e.g. ''3in1'', ''4in1'', ''All in 1''). Follow the instructions written on the packaging. • Select the programme according to the type of load and degree of soil. With the ECO programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. 10.2 Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher.
ENGLISH 10.6 Unloading the baskets 1. Let the tableware cool down before you remove it from the appliance. Hot items can be easily damaged. 2. First remove items from the lower basket, then from the upper basket. 43 At the end of the programme water can still remain on the sides and on the door of the appliance. 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results.
www.aeg.com 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.3 External cleaning 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. • Clean the appliance with a moist soft cloth. • Only use neutral detergents.
ENGLISH 45 Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The program does not start. • Make sure that the appliance door is closed. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to recharge the resin inside the water softener.
www.aeg.com Problem and alarm code Possible cause and solution Rattling/knocking sounds from inside the appliance. • The tableware is not properly arranged in the baskets. Refer to basket loading leaflet. • Make sure that the spray arms can rotate freely. The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use.
ENGLISH 47 Problem Possible cause and solution The dishes are wet. • For the best drying performance activate the option XtraDry. • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together.
www.aeg.com 13. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818-898 / 550 Electrical connection 1) Voltage (V) 200 - 240 Frequency (Hz) 50 / 60 bar (minimum and maximum) 0.5 - 8 MPa (minimum and maximum) 0.05 - 0.8 Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 15 Power consumption Left-on mode (W) 0.10 Power consumption Off-mode (W) 0.10 Water supply pressure 1) Refer to the rating plate for other values.
FRANÇAIS 49 TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ................................................................................... 50 2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 51 3. DESCRIPTION DE L'APPAREIL.............................................................................. 53 4. BANDEAU DE COMMANDE................................................................................. 54 5. PROGRAMMES.............................
1. www.aeg.com CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
FRANÇAIS • • • • • • • • 51 Respectez le nombre maximum de 15 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
www.aeg.com • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
FRANÇAIS 3. DESCRIPTION DE L'APPAREIL 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Bras d'aspersion supérieur Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 3.1 TimeBeam Le faisceau TimeBeam est une lumière projetée sur le sol, sous la porte de l'appareil. • Lorsque le programme démarre, la durée du programme s'affiche. • Lorsque le programme est terminé, 0:00 et CLEAN s'affichent.
www.aeg.com 4. BANDEAU DE COMMANDE 1 1 2 3 4 5 2 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Touche TimeSaver Touche XtraDry Touche ProBoost Voyants 4.1 Voyants Indicateur Description Voyant de fin. Voyant XtraDry. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme.
FRANÇAIS Programme Degré de salissure Type de vaisselle Phases du programme Options P2 2) • Tous • Vaisselle, couverts, plats et casseroles • Prélavage • Lavage de 45 °C à 70 °C • Rinçages • Séchage • ExtraHygiene • XtraDry 3) • Saleté variable • Vaisselle, couverts, plats et casseroles • Prélavage • Lavage de 50 °C à 65 °C • Rinçages • Séchage • TimeSaver • XtraDry • Très sale • Vaisselle, couverts, plats et casseroles • • • • • ProBoost • TimeSaver • XtraDry P5 • Normalement ou légèrement
www.aeg.com Programme Degré de salissure Type de vaisselle Phases du programme Options P9 • Normalement sale • Vaisselle et couverts • • • • • XtraDry 7) Prélavage Lavage à 50 °C Rinçages Séchage 1) Ce programme vous permet d'optimiser votre consommation d'eau et d'énergie pour la vaisselle et les couverts normalement sales. (Il s'agit du programme standard pour les instituts de tests.) 2) L'appareil détecte le degré de salissure et la quantité de vaisselle dans les paniers.
FRANÇAIS Eau (l) Consommation électrique (kWh) Durée (min) P7 10 0.9 30 P8 4 0.1 14 P9 9 - 10 1.0 - 1.2 219 - 229 Programme 1) 57 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.com votre région. Il est important de régler l'adoucisseur d'eau sur un niveau adéquat pour vous garantir de bons résultats de lavage. Dureté de l'eau Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Réglage du niveau de l'adoucisseur d'eau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.
FRANÇAIS Vous pouvez régler le dosage du liquide de rinçage entre 1 (dosage minimum) et 6 (dosage maximum). Le dosage 0 désactive le distributeur de liquide de rinçage, et le liquide n'est pas diffusé. Réglage usine : dosage 4. Comment régler le niveau de liquide de rinçage L'appareil doit être en mode Programmation. , , , et se mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants . , , L'appareil doit être en mode Programmation. 1.
www.aeg.com et se mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants , , , et s'éteignent. • Le voyant continue à clignoter. • L'affichage indique le réglage actuel : désactivé. 3. Appuyez sur réglage. = Signal sonore pour modifier le = Signal sonore activé. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.6 Comment régler la couleur du faisceau TimeBeam • Le voyant continue à clignoter. • Un chiffre et la lettre C s'affichent.
FRANÇAIS 7.1 XtraDry Activez cette option lorsque vous voulez améliorer les performances de séchage. En utilisant cette option, la durée de certains programmes, la consommation d'eau et la température du dernier rinçage peuvent être affectés. L'option XtraDry n'est pas une option permanente et doit être sélectionnée à chaque cycle. Comment activer l'option XtraDry Appuyez sur . Le voyant correspondant s'allume.
www.aeg.com • Durant la phase de séchage, un dispositif entrouvre la porte de l'appareil. • À la fin du programme, le dispositif se rétracte et la porte de l'appareil se referme. L'appareil s'éteint automatiquement. ATTENTION! N'essayez pas de fermer la porte de l'appareil lorsque le dispositif la maintient entrouverte. Vous risqueriez d'endommager l'appareil. Cette option n'est pas compatible avec d'autres programmes.
FRANÇAIS 63 ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. 5. Tournez le couvercle du réservoir de sel régénérant vers la droite pour refermer le réservoir. De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Risque de corrosion. Afin d'éviter cela, après avoir rempli le réservoir de sel régénérant, démarrez un programme. 1. Ouvrez le couvercle (C). 2.
www.aeg.com 9.1 Utilisation du produit de lavage A B C ATTENTION! Utilisez uniquement un produit de lavage spécial pour lave-vaisselle. 1. Appuyez sur la touche de déverrouillage (A) pour ouvrir le couvercle (C). 2. Versez le produit de lavage sous forme de poudre ou tablette dans le compartiment approprié (B). 3. Si le programme comporte une phase de prélavage, versez une petite quantité de produit de lavage à l'intérieur de la porte de l'appareil. 4. Fermez le couvercle.
FRANÇAIS Durant la phase de séchage, si la porte est ouverte pendant plus de 30 secondes, le programme en cours s'arrête. Cela ne se produit pas lorsque le programme avec l'option AutoOpen est en cours. Annulation du départ différé au cours du décompte Lorsque vous annulez le départ différé, vous devez régler de nouveau le programme et les options. 1. Ouvrez le couvercle de l'appareil. 2. Appuyez sur la touche Marche/Arrêt pour éteindre l'appareil. 3. Laissez l'appareil éteint pendant environ 30 secondes.
www.aeg.com du produit de lavage conçus pour les lave-vaisselle. D'autres produits peuvent endommager l'appareil. • Les pastilles tout en 1 sont généralement adaptées aux régions où la dureté de l'eau est inférieure à 21 °dH. Dans les régions où la dureté dépasse cette limite, du liquide de rinçage et du sel régénérant doivent être utilisés en complément des pastilles tout en 1.
FRANÇAIS 10.6 Déchargement des paniers 67 2. Déchargez d'abord le panier inférieur, puis le panier supérieur. À la fin du programme, les côtés et la porte de l'appareil peuvent être mouillés. 1. Attendez que la vaisselle refroidisse avant de la retirer du lave-vaisselle. La vaisselle encore chaude est sensible aux chocs. 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur.
www.aeg.com bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée.
FRANÇAIS 69 La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé. Problème et code d'alarme Cause et solution possibles L'appareil ne s'allume pas. • Assurez-vous que la fiche du câble d'alimentation est bien insérée dans la prise de courant. • Assurez-vous qu'aucun fusible n'est grillé dans la boîte à fusibles. Le programme ne démarre pas. • Vérifiez que la porte de l'appareil est fermée.
www.aeg.com Problème et code d'alarme Cause et solution possibles Le temps restant sur l'affichage augmente et passe presque instantanément à la fin du programme. • Ceci est normal. L'appareil fonctionne correctement. Petite fuite au niveau de la porte de l'appareil. • L'appareil n'est pas de niveau. Desserrez ou serrez les pieds réglables (si disponibles). • La porte de l'appareil n'est pas centrée avec la cuve. Réglez le pied arrière (si disponible). La porte de l'appareil est difficile à fermer.
FRANÇAIS 71 Problème Cause et solution possibles Résultats de séchage insatisfaisants. • La vaisselle est restée trop longtemps à l'intérieur de l'appareil, porte fermée. • Il n'y a pas de liquide de rinçage ou le dosage du liquide de rinçage n'est pas suffisant. Augmentez le niveau de distributeur de liquide de rinçage. • Les articles en plastiques peuvent avoir besoin d'être essuyés. • Pour de meilleurs performances de séchage, activez l'option XtraDry.
www.aeg.com Problème Cause et solution possibles Il y a des résidus de détergent • La pastille de détergent est restée coincée dans le disdans le distributeur de produit tributeur de produit de lavage, qui n'a donc pas été de lavage à la fin du proentièrement éliminée par l'eau. gramme. • L'eau ne peut pas éliminer le détergent du distributeur de produit de lavage. Assurez-vous que le bras d'aspersion n'est pas bloqué ou obstrué.
FRANÇAIS Consommation électrique Mode « Éteint » (W) 73 0.10 1) Reportez-vous à la plaque signalétique pour les autres valeurs. 2) Si l'eau chaude est produite à partir de sources d'énergie respectueuses de l'environnement (par exemple, panneaux solaires ou énergie éolienne), utilisez une arrivée d'eau chaude afin de réduire la consommation d'énergie. 14. EN MATIÈRE DE PROTECTION DE L'ENVIRONNEMENT Recyclez les matériaux portant le électroniques. Ne jetez pas les appareils symbole .
www.aeg.
FRANÇAIS 75
117900062-A-132015 www.aeg.