EN User Manual Dishwasher FAVORIT 88708 W0P
www.aeg.com CONTENTS 1. SAFETY INFORMATION.................................................................................................3 2. SAFETY INSTRUCTIONS................................................................................................ 4 3. PRODUCT DESCRIPTION.............................................................................................. 6 4. CONTROL PANEL...........................................................................................................7 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
ENGLISH • The water inlet hose has a safety valve and a sheath with an inner mains cable. 5 2.5 Internal light WARNING! Risk of injury. • This appliance has an internal lamp that comes on when you open the door and goes off when the door is closed. • The lamp in this appliance is not suitable for household room illumination. • To replace the lamp, contact the Service. WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket.
www.aeg.com 3.
ENGLISH 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Rinsing phase. It comes on when the rinsing phase operates. Drying phase. It comes on when the drying phase operates. End indicator. XtraDry indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator.
www.aeg.com 5.
ENGLISH 9 5.1 Consumption values Programme 1) Water (l) Energy (kWh) Duration (min) 11 0.857 225 7 - 14 0.6 - 1.6 40 - 160 14 - 16 1.2 - 1.5 139 - 155 12.5 - 14.5 1.4 - 1.8 169 - 179 9.5 - 10.5 1.10 - 1.30 55 - 65 10 0.9 30 9 - 10 1.1 - 1.3 219 - 229 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.
www.aeg.com The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area. It is important to set the right level of the water softener to assure good washing results.
ENGLISH Factory setting: level 4. How to set the rinse aid level The appliance must be in programme selection mode. 1. To enter the user mode, press and hold simultaneously Delay and Option until the indicators • The indicators and , go off. continues to • The indicator flash. • The display shows the current = level 4. setting: e.g. – The levels of rinse aid are from 0A to 6A. – Level 0 = no rinse aid is released. 3. Press Delay again and again to change the setting. 4.
www.aeg.com 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you have selected non compatible options, the appliance will automatically deactivate one or more of them. Only the indicators of the options still active will stay on. 7.1 XtraDry Activate this option when you want to boost the drying performance.
ENGLISH activated in user mode, activating TimeSaver option may deactivate AutoOpen temporarily. CAUTION! Do not try to close the appliance door while the device keeps the door ajar. This can cause damage to the appliance. If you want to deactivate AutoOpen, refer to "Settings". In this condition, the drying performance reduces significantly. AutoOpen is automatically activated when you select the programme 13 . To improve the drying performance refer to the XtraDry option or activate AutoOpen again.
www.aeg.com 8.2 How to fill the rinse aid dispenser A B 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) becomes clear. If you use multi-tablets and the drying performance is satisfactory, the rinse aid refill indication can be disabled.
ENGLISH detergent on the inner part of the appliance door. 4. Close the lid. Make sure that the lid locks into position. 9.2 Setting and starting a programme The Auto Off function This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation: • 5 minutes after the completion of the programme. • After 5 minutes if the programme has not started. Starting a programme 1. Press the on/off button to activate the appliance.
www.aeg.com 10. HINTS AND TIPS 10.1 General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase. • Always use the whole space of the baskets.
ENGLISH • Make sure that the spray arm can move freely before you start a programme. 10.5 Before starting a programme Make sure that: • The filters are clean and correctly installed. • The cap of the salt container is tight. • The spray arms are not clogged. • There is dishwasher salt and rinse aid (unless you use multi- tablets). • The position of the items in the baskets is correct. • The programme is applicable for the type of load and for the degree of soil.
www.aeg.com 11.2 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. Clogged holes can cause unsatisfactory washing results. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 1. Pull out the upper basket. 2.
ENGLISH 19 11.4 Internal cleaning 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth. • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance.
www.aeg.com Problem and alarm code Possible cause and solution The appliance does not fill with water. • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the filter in the inlet hose is not clogged. • Make sure that the inlet hose has no kinks or bends. The display shows . The appliance does not drain the water.
ENGLISH Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes. Once you have checked the appliance, deactivate and activate the appliance. If 21 the problem occurs again, contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre. 12.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results.
www.aeg.com Problem Possible cause and solution Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener". • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together. There are residues of detergent in the dispenser at the end of the programme. • The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
ENGLISH Power consumption Off-mode (W) 23 0.10 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption. 14. ENVIRONMENTAL CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances.
117892192-442015 www.aeg.