EN User Manual Dishwasher FAVORIT 88709M0P FAVORIT 88709W0P
www.aeg.com CONTENTS 1. SAFETY INFORMATION.................................................................................................3 2. SAFETY INSTRUCTIONS................................................................................................ 4 3. PRODUCT DESCRIPTION.............................................................................................. 5 4. CONTROL PANEL...........................................................................................................6 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com • • • • • • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
ENGLISH WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is completed.
www.aeg.com 5 6 7 8 9 Filters Rating plate Salt container Air vent Rinse aid dispenser 10 11 12 13 Detergent dispenser Lower basket Upper basket Cutlery drawer 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program touchpad Programme indicators Display Delay touchpad 3 4 7 5 6 6 Option touchpad 7 Indicators 8 Start touchpad 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Rinsing phase. It comes on when the rinsing phase operates.
ENGLISH Indicator Description Rinse aid indicator. It is always off while the programme operates. TimeSaver indicator. Delay indicator. ExtraHygiene indicator. 5.
www.aeg.com Programme 6) Degree of soil Type of load Programme phases • Normal soil • Prewash • Crockery and cut- • Wash 50 °C lery • Rinses • Dry Options • XtraDry 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets .
ENGLISH 9 6. SETTINGS 6.1 Programme selection mode and user mode When the appliance is in programme selection mode it is possible to set a programme and to enter the user mode. In user mode, the following settings can be changed: • The level of the water softener according to the water hardness. • The activation or deactivation of the rinse aid dispenser. • The level of rinse aid according to the required dosage. These settings will be saved until you change them again.
www.aeg.com If you use multi-tablets containing salt and the hardness of your water is lower than 21°dH, you can set the lowest water softener level. It deactivates the salt refill indicator. If you use standard detergent or multitablets without salt, set the proper water hardness level to keep the salt refill indicator active. How to set the water softener level The appliance must be in programme selection mode. 1.
ENGLISH • The indicator continues to flash. • The display shows the current setting: = the rinse aid dispenser is activated (factory setting). 3. Press Start to change the setting. = the rinse aid dispenser is deactivated. 4. Press the on/off button to confirm the setting. 6.5 How to deactivate AutoOpen The appliance must be in programme selection mode. Option until the indicators 11 , , and start to flash and the display is blank. 2. Press Start. • The indicators and , go off.
www.aeg.com The display shows the updated programme duration. 7.3 ExtraHygiene With this option you have better hygiene results. During the last rinsing phase, the temperature stays at 70 °C for at least 10 minutes. If the option is not applicable to the programme, the related indicator does not come on or it flashes quickly for a few seconds and then goes off. The display shows the updated programme duration. How to activate ExtraHygiene Press Option until the indicator comes on. 8.
ENGLISH 8.2 How to fill the rinse aid dispenser A B 13 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) becomes clear. If you use multi-tablets and the drying performance is satisfactory, the rinse aid refill indication can be disabled.
www.aeg.com detergent on the inner part of the appliance door. 4. Close the lid. Make sure that the lid locks into position. 9.2 Setting and starting a programme The Auto Off function This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation: • 5 minutes after the completion of the programme. • After 5 minutes if the programme has not started. Starting a programme 1.
ENGLISH 15 10. HINTS AND TIPS 10.1 General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase. • Always use the whole space of the baskets.
www.aeg.com • Make sure that the spray arm can move freely before you start a programme. 10.5 Before starting a programme Make sure that: • The filters are clean and correctly installed. • The cap of the salt container is tight. • The spray arms are not clogged. • There is dishwasher salt and rinse aid (unless you use multi- tablets). • The position of the items in the baskets is correct. • The programme is applicable for the type of load and for the degree of soil.
ENGLISH 17 11.2 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. Clogged holes can cause unsatisfactory washing results. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 1. Pull out the upper basket. 2.
www.aeg.com 11.4 Internal cleaning 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth. • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance.
ENGLISH 19 Problem and alarm code Possible cause and solution The appliance does not fill with water. • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the filter in the inlet hose is not clogged. • Make sure that the inlet hose has no kinks or bends. The display shows . The appliance does not drain the water.
www.aeg.com Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes. Once you have checked the appliance, deactivate and activate the appliance. If the problem occurs again, contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre. 12.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results.
ENGLISH 21 Problem Possible cause and solution Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener". • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together. There are residues of detergent in the dispenser at the end of the programme. • The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
www.aeg.com Power consumption Off-mode (W) 0.10 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption. 14. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances.
ENGLISH 23
117904883-A-292015 www.aeg.