ÖKO_FAVORIT 30640 i Geschirrspülautomat Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch. Beachten Sie vor allem die Sicherheitshinweise auf den ersten Seiten dieser Benutzerinformation! Bewahren Sie bitte die Benutzerinformation zum späteren Nachschlagen auf. Geben Sie sie an eventuelle Nachbesitzer des Gerätes weiter.
Inhalt INHALT Gebrauchsanweisung ...................................... 5 Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Wirtschaftlich und umweltbewußt spülen . . . . . . . . . . . . . . . . . . . . . . . . 7 Geräteansicht und Bedienblende . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bedienblende . . .
Inhalt Aufstell- und Anschlußanweisung . . . . . . . . . . . . . . . . . . . . . . . 31 Aufstellen des Geschirrspülers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Integrierbarer Geschirrspüler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Anschließen des Geschirrspülers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wasseranschluß . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gebrauchsanweisung GEBRAUCHSANWEISUNG 1 Sicherheitshinweise Die Sicherheit von AEG-Elektrogeräten entspricht den anerkannten Regeln der Technik und dem Gerätesicherheitsgesetz. Dennoch sehen wir uns als Hersteller veranlaßt, Sie mit folgenden Sicherheitshinweisen vertraut zu machen: Aufstellung, Anschluß, Inbetriebnahme • Der Geschirrspüler darf nur stehend transportiert werden. • Überprüfen Sie den Geschirrspüler auf Transportschäden. Ein beschädigtes Gerät auf keinen Fall anschließen.
Gebrauchsanweisung Allgemeine Sicherheit • Reparaturen am Geschirrspüler dürfen nur von Fachkräften durchgeführt werden. Durch unsachgemäße Reparaturen können erhebliche Gefahren für den Benutzer entstehen. Wenden Sie sich im Reparaturfall an unseren Kundendienst oder an Ihren Fachhändler. • Geschirrspüler nie in Betrieb nehmen, wenn Netzkabel, Zu- /Ablaufschlauch beschädigt sind oder Bedienblende, Arbeitsplatte oder der Sockelbereich so beschädigt sind, daß das Gerät offen zugänglich ist.
Gebrauchsanweisung • Setzen oder stellen Sie sich nicht auf die geöffnete Tür, das Gerät könnte kippen. • Im Fehlerfall zuerst Wasserhahn schließen, dann das Gerät ausschalten und Netzstecker aus der Steckdose ziehen. Bei Festanschluß: Sicherung(en) ausschalten bzw. Schraubsicherungen herausdrehen. 2 Entsorgung Verpackungsmaterial entsorgen Entsorgen Sie das Verpackungsmaterial des Geschirrspülautomaten sachgerecht. Alle verwendeten Verpackungsmaterialien sind umweltverträglich und wiederverwertbar.
Gebrauchsanweisung Geräteansicht und Bedienblende Deckendusche Gummidichtung für Ankopplung des Wasserzulaufs zum oberen Sprüharm Sprüharme Vorratsbehälter für Spezialsalz Vorratsbehälter für Klarspüler Behälter für Reinigungsmittel Typschild Siebe 8
Gebrauchsanweisung Bedienblende Enthärter- FunktionsTaste Taste Mehrfachanzeige Spülprogrammtasten Kontrollanzeige Türgriff EIN / AUS - Taste Enthärter- und Funktions-Taste: Zusätzlich zum aufgedruckten Spülprogramm kann durch die Kombination dieser Tasten der Wasserenthärter des Geschirrspülers eingestellt werden. Die 3 Lampen der Mehrfachanzeige können anzeigen : – den aktuellen Programmabschnitt des gewählten Spülprogramms. – welcher Fehler am Geschirrspüler vorliegt.
Gebrauchsanweisung Vor der ersten Inbetriebnahme Entfernen Sie vor Inbetriebnahme alle Klammern, mit denen die Geschirrkörbe für den Transport gesichert werden. Führen Sie dann folgende Schritte durch: 1. Wasserenthärter einstellen 2. Spezialsalz für Wasserenthärter einfüllen 3. Klarspüler einfüllen Wasserenthärter einstellen Um Kalkablagerungen auf Geschirr und im Geschirrspüler zu verhindern, muß das Geschirr mit weichem, d.h. kalkarmen Wasser gespült werden.
Gebrauchsanweisung Die Härtebereich-Einstellung kann nur im programmlosen Zustand erfolgen. Sollten Sie aus Versehen ein Programm gestartet haben (eine LED-Leuchte leuchtet ständig), so muss durch Drücken der entsprechenden Taste das Programm gelöscht werden. 1. Gerät muß ausgeschaltet sein. 2. Enthärter- und Funktions-Taste gleichzeitig drücken und gedrückt halten. 3. Zusätzlich EIN/AUS-Taste drücken. 4. LED-Anzeige der Enthärter-Taste leuchtet erst 5 Sekunden lang konstant und fängt dann an zu blinken.
Gebrauchsanweisung Spezialsalz für Wasserenthärter einfüllen 1 Verwenden Sie nur Spezialsalz für Geschirrspüler. Füllen Sie niemals andere Salzarten (z.B. Speisesalz) oder Geschirrspülreiniger in den Salzvorratsbehälter. Dies würde den Wasserenthärter zerstören. Überzeugen Sie sich vor jedem Salzeinfüllen, daß Sie wirklich eine Pakkung Spezialsalz in der Hand haben. Füllen Sie Spezialsalz ein: – Vor der ersten Inbetriebnahme des Geschirrspülers.
Gebrauchsanweisung Klarspüler einfüllen Durch den Klarspüler erhält man fleckenfreies, glänzendes Geschirr und klare Gläser. 1 Verwenden Sie nur Marken-Klarspüler für Geschirrspüler. Füllen Sie niemals andere Mittel (z.B. Essigessenz) oder Geschirrspülreiniger in den Vorratsbehälter für Klarspüler. Dies würde das Gerät beschädigen.
Gebrauchsanweisung Klarspülerdosierung einstellen Beim Geschirrspülen wird aus dem Vorratsfach Klarspüler ins Spülwasser abgegeben. Die Dosierung können Sie von 1-6 einstellen. Vom Werk ist die Dosierung auf „4“ eingestellt. Dosierung nur dann verändern, wenn auf Gläsern und Geschirr Schlieren, milchige Flecken oder angetrocknete Wassertropfen zu sehen sind. (siehe unter „Was tun, wenn...“). 0 1. Geschirrspülertür öffnen. 2. Mit Finger den Entriegelungsknopf des Klarspülerfachs drücken. 3.
Gebrauchsanweisung Im täglichen Gebrauch • Muß Spezialsalz oder Klarspüler nachgefüllt werden ? • Besteck und Geschirr in Geschirrspüler einordnen • Reinigungsmittel für Geschirrspüler einfüllen • Für Besteck und Geschirr geeignetes Spülprogramm auswählen • Spülprogramm starten Besteck und Geschirr einordnen 1 Schwämme, Haushaltstücher und alle Gegenstände, die sich mit Wasser vollsaugen können, dürfen nicht im Geschirrspüler gereinigt werden.
Gebrauchsanweisung – um Glasschäden zu vermeiden, dürfen Gläser sich nicht berühren – kleine Gegenstände (z. B. Deckel) in den Besteckkorb legen Besteck einordnen Lange, spitze Besteckteile stellen im Besteckkorb, besonders für Kinder eine Gefahrenquelle dar (siehe Sicherheitshinweise). Sie müssen daher in den Oberkorb gelegt werden. Damit alle Besteckteile vom Wasser umspült werden, sollten Sie 1. den Gittereinsatz auf den Besteckkorb aufstecken 2.
Gebrauchsanweisung Töpfe, Pfannen und große Teller einordnen Größeres und stark verschmutztes Geschirr im Unterkorb einordnen. Um größeres Geschirr leichter einordnen zu können, sind bei einigen Geschirrspülermodellen die beiden Reihen des rechten Tellereinsatzes klappbar: 0 1. Rechte Tellereinsätze hinten leicht anheben. 3 2. Tellereinsätze nach links umklappen.
Gebrauchsanweisung Tassen, Gläser und Kaffeeservice einordnen Kleineres, empfindliches Geschirr und lange, spitze Besteckteile im Oberkorb einordnen. • Geschirrteile auf und unter den klappbaren Tassenauflagen versetzt anordnen, damit das Spülwasser alle Geschirrteile erreicht. • Für hohe Geschirrteile lassen sich die Tassenauflagen hochklappen. • Wein-, Sekt- sowie Cognacgläser in die Ausschnitte der Tassenauflagen lehnen bzw. hängen. • Gläser, Becher usw.
Gebrauchsanweisung Oberkorb in der Höhe verstellen Maximale Höhe des Geschirrs im Oberkorb Unterkorb 3 bei angehobenem Oberkorb 22 cm 31 cm bei abgesenktem Oberkorb 24 cm 29 cm Die Höhenverstellung ist auch bei beladenen Körben möglich. Je nach Modell ist das Gerät mit dem Oberkorb „Variante 1“ oder „Variante 2“ ausgestattet: Absenken des Oberkorbs: 0 1. Oberkorb ganz herausziehen. 2. Oberkorb rechts hinten anheben und absenken. Variante 1 Anheben des Oberkorbs: 0 1. Oberkorb ganz herausziehen.
Gebrauchsanweisung Reinigungsmittel einfüllen 1 Verwenden Sie nur Reinigungsmittel für Geschirrspüler. Füllen Sie Reinigungsmittel ein: – Vor Beginn eines Spülprogramms (nicht beim Programm Vorspülen). Reinigungsmittel wird während des Programms ins Spülwasser abgegeben. Beachten Sie bitte die Dosier- und Lagerempfehlungen der Hersteller auf den Verpackungen der Reinigungsmittel. Das Fach für Reinigungsmittel ist auf der Innenseite der Tür. 0 1.
Gebrauchsanweisung Bio-Spülprogramme und Kompaktreiniger Reinigungsmittel für Geschirrspüler lassen sich anhand ihrer chemischen Zusammensetzung in zwei Grundtypen einteilen: – herkömmliche, alkalische Reiniger mit ätzenden Bestandteilen – niederalkalische Kompaktreiniger mit natürlichen Enzymen.
Gebrauchsanweisung Spülprogramm auswählen (Programmtabelle) Wählen Sie mit Hilfe dieser Tabelle das geeignete Spülprogramm aus: Geschirrart zusätzlich - Art der Verschmut- • stark verschmutzt zung • angetrocknete Speisereste, besonders Eiweiß und Stärke Geeignetes Spülprogramm: Programmablauf 1) mit temperaturempfindlichem Geschirr • normal verschmutzt mit empfindlichen Gläsern • leicht verschmutzt besonders geeignet bei Verwendung von Kompaktreinigern.
Gebrauchsanweisung Spülprogramm starten 0 1. Überprüfen Sie, ob Geschirr und Besteck im Geschirrspüler so eingeord- net sind, daß die Sprüharme sich frei drehen können. 2. Wasserhahn ganz aufdrehen. 3. Tür schließen. 4. EIN/AUS-Taste drücken. Anzeige der EIN/AUS-Taste leuchtet. 5. Programmtaste für das gewünschte Programm drücken (siehe „Programmtabelle“). Programmanzeige leuchtet. Ein oder zwei Lampen der Mehrfachanzeige blinken. Das Programm kann während dieser Zeit umgewählt werden.
Gebrauchsanweisung Pause-Funktion Mit der Pause-Funktion kann das Spülprogramm für kurze Zeit angehalten werden: 0 1. EIN/AUS-Taste drücken. Das Spülprogramm stoppt. 2. Alle Anzeigen erlöschen. 3. Wenn nach kurzer Zeit das Spülprogramm fortgesetzt werden soll, wieder EIN/AUS-Taste drücken. Das Spülprogramm läuft weiter. Das Spülprogramm sollte nicht für längere Zeit angehalten werden, da sonst das abgekühlte Spülwasser wieder erhitzt werden muß und somit der Energieverbrauch steigen würde.
Gebrauchsanweisung Pflege und Reinigung 1 Auf keinen Fall handelsübliche Möbelpflege- oder aggressive Reinigungsmittel verwenden. • Bedienteile des Geschirrspülers bei Bedarf nur mit einem weichen Lappen und warmem, klarem Wasser reinigen. • Sprüharme brauchen nicht gereinigt zu werden. • Innenbehälter, Türdichtung und Wasserzulauf gelegentlich auf Verschmutzungen kontrollieren und gegebenfalls reinigen. Reinigung der Siebe Die Siebe im Spülraumboden sind in hohem Grade selbstreinigend.
Gebrauchsanweisung 7. Flächensieb wieder in den Spülraumboden einsetzen. 8. Grob-/Feinsieb in den Mikrofilter einsetzen und zusammenstecken. 9. Siebkombination einsetzen und durch Schwenken des Griffs im Uhrzeigersinn bis zum Anschlag verriegeln. Darauf achten, daß das Flächensieb nicht über den Spülraumboden heraussteht. 1 26 Ohne Siebe darf auf keinen Fall gespült werden.
Gebrauchsanweisung Was tun, wenn... Versuchen Sie mit Hilfe der hier aufgeführten Hinweise kleinere Störungen am Geschirrspüler selbst zu beheben. Wenn Sie bei einer der hier aufgeführten Störungen oder zur Behebung eines Bedienfehlers den Kundendienst in Anspruch nehmen, erfolgt der Besuch des Kundendienst-Technikers auch während der Garantiezeit nicht kostenlos. ...Fehlermeldungen angezeigt werden.
Gebrauchsanweisung ...es Probleme beim Betrieb des Geschirrspülers gibt. Störung Programm startet nicht. Mögliche Ursache Abhilfe Geschirrspülertür ist nicht richtig geschlossen. Tür schließen. Netzstecker ist nicht eingesteckt. Netzstecker einstecken. Sicherung der Hausinstallation ist nicht in Ordnung. Sicherung ersetzen. Bei Geschirrspülermodellen Falls Geschirr sofort gespült mit Startzeitvorwahl: werden soll, StartzeitvorEine Startzeit ist vorgewählt. wahl löschen.
Gebrauchsanweisung Auf Gläsern und Geschirr sind Schlieren, Streifen, milchige Flecken oder blauschimmernder Belag. – Klarspülerdosierung niedriger einstellen. Auf Gläsern und Geschirr sind angetrocknete Wassertropfen. – Klarspülerdosierung höher einstellen. – Der Reiniger kann die Ursache sein. Kontaktieren Sie den Kundenberater des Reinigungsmittelherstellers. Technische Daten Fassungsvermögen: 12 Maßgedecke einschließlich Servicegeschirr Zulässiger Wasserdruck: 1-10 bar (=10-100 N/cm2 = 0.1-1.
Gebrauchsanweisung Hinweise für Prüfinstitute Die Prüfung nach EN 60704 muß bei voller Beladung mit dem Testprogramm (siehe Programmtabelle) durchgeführt werden. Die Prüfungen nach EN 50242 müssen mit vollem Salzbehälter des Wasserenthärters, mit vollem Vorratsbehälter für Klarspüler und mit dem Testprogramm (siehe Programmtabelle) durchgeführt werden. Reinigerdosierung : Volle Beladung: 12 Maßgedecke einschl. Servicegeschirr Halbvolle Beladung: 6 Maßgedecke einschl.
Aufstell- und Anschlußanweisung AUFSTELLSTELL- UND ANSCHLUßANWEISUNG Aufstellen des Geschirrspülers • Geschirrspüler muß standsicher und waagrecht ausgerichtet auf festem Boden aufgestellt werden. • Um Bodenunebenheiten auszugleichen und Gerätehöhe an andere Möbel anzugleichen, Schraubfüße herausschrauben: – mit einem Schraubendreher. • Bei Unterbau-, integrierbaren und vollintegrierbaren Geschirrspülern sind die hinteren Gerätefüße mit einem Schraubendreher vorne am Gerät einzustellen.
Aufstell- und Anschlußanweisung Integrierbarer Geschirrspüler (siehe beiliegende Montageschablone) 3 Die Gerätetür kann mit einer Holzplatte/Möbelplatte folgender Abmessungen verkleidet werden: Breite: 591 – 594 mm Dicke: 16 – 24 mm Höhe: abhängig von (variabel) – Nischenhöhe – Sockelhöhe – Anpassung an Fugenverlauf benachbarter Möbel Das genaue Höhenmaß muß am Aufstellort von den benachbarten Möbeln abgemessen werden. Gewicht: max.
Aufstell- und Anschlußanweisung Anschließen des Geschirrspülers Wasseranschluß Der Geschirrspüler hat Sicherheitseinrichtungen, die den Rückfluß von Spülwasser in das Trinkwasser-Leitungsnetz verhindern und den geltenden wassertechnischen Sicherheitsvorschriften entsprechen. • Der Geschirrspüler kann an Kaltwasser und an Warmwasser bis max. 60 °C angeschlossen werden. • Der Geschirrspüler darf nicht an offene Warmwassergeräte und Durchlauferhitzer angeschlossen werden.
Aufstell- und Anschlußanweisung Wasserablauf Ablaufschlauch 1 Der Ablaufschlauch darf nicht geknickt, gequetscht oder in sich verschlungen sein. • Anschluß des Ablaufschlauches: – maximal zulässige Höhe: 1 Meter. – minimal erforderliche Höhe 30cm über der Geräteunterkante. Verlängerungsschläuche • Verlängerungsschläuche sind über den Fachhandel oder unseren Kundendienst zu beziehen. Der Innendurchmesser der Verlängerungsschläuche muß 19 mm betragen, damit die Gerätefunktion nicht gestört wird.
Aufstell- und Anschlußanweisung Wasserschutzsystem Zum Schutz gegen Wasserschäden ist der Geschirrspüler mit einem Wasserschutzsystem, dem AQUA CONTROL SYSTEM ausgestattet. Im Fehlerfall unterbricht das Sicherheitsventil im Gerät sofort den Wasserzulauf und die Entleerungspumpe schaltet sich ein. Damit kann Wasser weder aus- noch überlaufen. Im Gerät befindliches Restwasser wird automatisch abgepumpt.
Aufstell- und Anschlußanweisung Anschlußtechnik Zulauf- und Ablaufschläuche sowie das Netzkabel müssen seitlich vom Geschirrspüler angeschlossen werden, da hinter dem Gerät kein Platz dafür ist. Das nachfolgende Beispiel einer Sanitär- und Elektroinstallation kann nur eine Empfehlung sein, da maßgebend die Gegebenheiten am Aufstellort sind (vorhandene Anschlüsse, örtliche Anschlußvorschriften der Energie- bzw. der Wasserwerke, usw...).
Kundendienststellen KUNDENDIENSTSTELLEN Deutschland Sehr geehrter Kunde, der Werkskundendienst von AEG Hausgeräte ist dezentral organisiert. Damit bieten wir Ihnen überall einen zuverlässigen Service. Unter der für Sie kostengünstigen Rufnummer 0180 322 66 22 (EUR 0.09 / Minute) können Sie im Bedarfsfall einen unserer Spezialisten oder Service-Partner anfordern. Ihre Ersatzteil-Bestellung geben Sie bitte unter der zentralen Rufnummer 0180 5 00 10 76 auf. (EUR 0.
Kundendienststellen PLZ Adresse 52068 Aachen* Auf der Hüls 197 56068 Koblenz* Rheinstraße 17 56070 Koblenz* A.-Hosch-Str. 14 57072 Siegen* Sandstraße 173 59071 Hamm Ostwennemarstr. 1 60326 Frankfurt Mainzer Landstraße 349 66115 Saarbrücken-Malstatt* Ludwigstraße 55-57 67663 Kaiserslautern* Pariser Straße 200 71034 Böblingen-Hulb Dornierstraße 7 74743 Seckach Bergstr. 9F 76185 Karlsruhe-Mühlburg* Neureuther Straße 5-7 78054 Villingen-Schwenningen* Alleenstr.
Kundendienststellen Weitere Service-Stellen sind in: 03222 Groß Klessow 06896 Wittenberg-Reinsdorf 15517 Fürstenwalde 16515 Oranienburg 17039 Ihlenfeld 18069 Rostock 19057 Schwerin 24354 Rieseby 25980 Westerland/Sylt 26639 Wiesmoor 27726 Worpswede 30900 Wedemark 32825 Blomberg 34497 Korbach 36043 Fulda 39114 Magdeburg 49377 Vechta 63906 Erlenbach 78244 Bietingen 84307 Eggenfelden 87549 Rettenberg 99819 Ettenhausen 39
Kundendienststellen Österreich Adresse Bereich Electrolux Hausgeräte GmbH Telefon Telefax 01/ 8 66 40-0 01/ 8 66 40-305 Herziggasse 9 Ersatzteilverkauf 01/ 8 66 40-315 1230 Wien Reparaturannahme 01/ 8 66 40-330 kundendienst@electrolux.co.at Technische Auskünfte 01/ 8 66 40-399 01/ 8 66 40-300 01/ 8 66 40-300 Werkskundendienst für die Marken AEG - Electrolux - Juno - Zanussi 40 Adresse Telefon Telefax Hausgeräte Kundendienst GmbH Winetzhammerstraße 8 4030 Linz hg.kundendienst.linz@aon.
Garantiebedingungen GARANTIEBEDINGUNGEN Deutschland Der Endabnehmer dieses Gerätes (Verbraucher) hat bei einem Kauf dieses Gerätes von einem Unternehmer (Händler) in Deutschland im Rahmen der Vorschriften über den Verbrauchsgüterkauf gesetzliche Rechte, die durch diese Garantie nicht eingeschränkt werden. Diese Garantie räumt dem Verbraucher also zusätzliche Rechte ein.
Garantiebedingungen Österreich 1. Für AEG Hausgeräte leisten wir unter den nachstehenden Bedingungen Garantie. Durch diese Garantie werden Ansprüche des Endabnehmers gegen den Händler (im Sinne des Konsumentenschutzgesetzes) aus dem Kaufvertrag nicht berührt. 2. Die Garantiezeit beträgt 12 Monate, für emaillierte Innenkessel der Heißwasserspeicher weitere 24 Monate, und beginnt mit dem Zeitpunkt der Übergabe des Gerätes.
Service SERVICE Im Kapitel „Was tun, wenn...“ sind die wichtigsten Fehlerquellen zusammengestellt, die Sie selbst beheben können. Wenn Sie trotzdem für einen der aufgeführten Hinweise oder aufgrund von Fehlbedienung den Kundendienst in Anspruch nehmen, so erfolgt der Besuch des Kundendienst-Technikers auch während der Garantiezeit nicht kostenlos. Wenn Sie für eine Störung keinen Hinweis in dieser Gebrauchsanweisung finden, wenden Sie sich bitte an den Kundendienst.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.