FAVORIT 40660 i Dishwasher User Instructions
Dear customer, Please read these user instructions carefully. Please observe the safety instructions on the first few pages of these user instructions! Please keep these user instructions for later reference. Pass them on to any subsequent owner of the appliance. 1 0 The warning triangle and/or specific words (Warning!, Caution!, Important!) are used to highlight instructions that are important for your safety or for the function of the appliance. It is imperative that these instructions are observed.
Contents CONTENTS Operating Instructions .................................... 5 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Economical and Ecological Dishwashing . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Appliance Features and Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Installation and Connection Instructions . . . . . . . . . . . . . . . . 30 Installing the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Dishwashers That Can Be Integrated . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Connecting the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions OPERATING INSTRUCTIONS 1 Safety Instructions The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law. Nevertheless, as a manufacturer we consider it our obligation to make you aware of the following safety information: Installation, Connection and Placing into Operation • The dishwasher may only be transported upright. • Check the dishwasher for transport damage.
Operating Instructions • Never place the dishwasher in operation if the mains cable, water inlet or drain hose is damaged; or the control panel, work top or plinth area is damaged such that the inside of the appliance is freely accessible. • If the mains lead is damaged, or is to be replaced for a longer lead, the cable (obtainable from AEG Service Force) must be replaced by a service engineer authorised by AEG. • Never unplug the appliance by pulling on the cable, always pull the plug.
Operating Instructions • In the event of a fault, first close the tap, then switch off the appliance and unplug it from the mains. If the appliance is permanently wired to the mains: remove the fuse. 2 Disposal Disposing of the Packaging Material Dispose of the dishwasher packaging material correctly. All the packaging materials used are harmless to the environment and can be recycled. • Plastic parts are marked with standard international abbreviations: – >PE< for polyethylene, e.g.
Operating Instructions Appliance Features and Control Panel Top Spray Nozzle Rubber Seal for Connecting the Water Feed to the Upper Spray Arm Spray Arms Container for Salt Container for Rinse Aid Detergent Dispenser Rating Filters Plate 8
Operating Instructions Control panel Water sof- Function tener button button Multi-display Wash programme buttons Control indicator Door handle ON / OFF button Water softener and function button: In addition to the wash programme marked, it is also possible to adjust the dishwasher's water softener using a combination of these buttons. The 3 lights of the multi-display can display: – the current stage of the selected wash programme. – which fault has occurred in the dishwasher.
Operating Instructions Prior to using for the first time Prior to using for the first time, remove all the clips with which the dish racks are secured for transport. Then perform the following steps: 0 1. Adjust the water softener 2. Fill with Salt for the Water Softener 3. Fill with Rinse Aid Adjusting the water softener To avoid scale deposits on the dishes and in the dishwasher, the dishes must be washed with soft water i.e. low lime content.
Operating Instructions The hardness range cannot be set if a programme is running. If you have inadvertently started a programme (an LED indicator is constantly illuminated) the programme must be cancelled by pressing the appropriate button. 1. The appliance must be switched off. 2. Press the water softener button and the function button simultaneously and hold them down. 3. In addition press the ON/OFF button. 4.
Operating Instructions Filling with Salt for the Water Softener 1 Use only salt designed for dishwashers. Never fill the salt container with any another type of salt (e.g. culinary salt) or dishwasher detergent as this would irreparably damage the water softener. Prior to filling with salt, please check each time that you really do have a packet of dishwasher salt in your hand.
Operating Instructions Filling with Rinse Aid Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, spot and streak free drying. 1 Only use rinse aid specifically designed for domestic dishwashers. Never fill the rinse aid container with any other substance as this would damage the appliance. Fill with rinse aid: – Prior to using the dishwasher for the first time – When the window indicator has a dark centre surrounded by a light ring.
Operating Instructions Adjusting Rinse Aid Dosing 3 As the dishes are washed rinse aid is released from the dispenser into the wash water. The dose is factory set at 4, and can be adjusted from 1 to 6. Only change the setting if streaks, milky spots or dried on water marks are visible on glasses or crockery. 0 1. Open the door of the dishwasher. 2. Press the rinse aid compartment release button with your finger. 3. Fully open the rinse aid compartment lid. 4. Set the dose level. 5.
Operating Instructions In Daily Use • Check the salt and rinse aid levels. • Load cutlery and dishes into the dishwasher • Fill with dishwasher detergent • Select a wash programme suitable for the cutlery and dishes • Start the wash programme Loading Cutlery and Dishes 1 Sponges, household cloths and any object that can absorb water should not be washed in the dishwasher.
Operating Instructions – To avoid damage to glasses, they must not touch – Do not lay small objects (e.g. lids) in the cutlery rack Loading Cutlery 1 Long bladed knives stored in an upright position are a potential hazard. 1 Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Take care when loading or unloading sharp items such as knives. To ensure that all items of cutlery are completely washed, you should 1.
Operating Instructions Loading Pans, Frying Pans and Large Plates Load large and heavily soiled dishes in the lower rack. To ease the loading of large items at some dishwasher-models the two rows of prongs for the right-hand plate insert can be folded down: 0 1. Slightly lift the right plate insert. 3 2. Fold the plate insert to the left.
Operating Instructions Loading Cups, Glasses and Coffee Services Load small, delicate items and long pointed cutlery in the upper rack. • Arrange items of crockery on the folding cups racks so that they are offset from each other and water can reach all items. • The cup racks can be folded up out of the way for tall items. • Lay or hang wine, champagne, and brandy glasses in the cut outs on the cup racks. • Glasses, beakers, etc. can also be placed on the two rows of prongs on the left of the upper rack.
Operating Instructions Filling with Detergent 1 Only use dishwasher detergent. Fill with detergent: – Prior to the start of a wash programme (not for the pre wash programme). The detergent is released into the wash water during the programme. Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging. The detergent compartment is on the inside of the dishwasher door. 0 1. If the lid is closed: press release button (1). The lid springs open. 2 2.
Operating Instructions Bio Wash Programmes and Concentrated Detergents Based on their chemical composition, dishwasher detergents can be split into two basic types: – Conventional, alkaline detergents with caustic components – Weak alkaline concentrated detergents with natural enzymes.
Operating Instructions Selecting the Wash Programme (Programme Table) Choose the most suitable wash programme with the aid of this table: Type of dishes in addition Type of soiling Suitable wash programme: Programme sequence 1) Dessert dishes and coffee service Dinner service and cooking utensils • heavily soiled • dried on leftovers, particularly egg white and thickeners • normally soiled • dried left-overs • normally soiled with fragile glasses • lightly soiled particularly suited to the use of c
Operating Instructions Start the wash programme 0 1. Check that when the dishes and cutlery are loaded in the dishwasher the spray arms are free to rotate. 2. Open the water tap fully. 3. Shut the door. 4. Press the ON/OFF button. ON/OFF button indicator comes on. 5. Press the button for the programme required (see “Programme Table“). The programme indicator lights up. One or two lights will flash in the multidisplay. During this time it is possible to reselect the programme.
Operating Instructions Pause function Using the pause function the dishwasher can be temporarily stopped: 0 1. Press the ON/OFF button. The wash programme will stop. 2. All indicators will go out. 3. After a short time when the wash programme is to continue, press the ON/OFF button again. The wash programme will continue. The wash programme should not be stopped for a prolonged period or the cooled water will need to be reheated resulting in increased energy consumption.
Operating Instructions Care and Cleaning 1 Do not under any circumstances use furniture care products or aggressive cleaners. • If necessary, clean the controls only with a soft cloth and pure warm water. • The spray arms do not need cleaning. • Occasionally check the internal containers, door seal, and water inlet for soiling, clean if necessary. Cleaning the Filter The filters should be checked and cleaned regularly. Blocked filters will give poor wash results. 0 1.
Operating Instructions 7. Put the flat filter back in the base of the washing compartment 8. Place the coarse/fine filter in the microfilter and press together. 9. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment. 1 The dishwasher must not be used without filters under any circumstances.
Operating Instructions What to do, if ... Try to rectify minor faults on the dishwasher with the aid of the instructions given here. If you call an engineer to resolve a of fault listed here, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is in guarantee. ...Fault warnings are displayed. • If the top or middle light in the display is flashing you can probably rectify the fault yourself. Once the fault has been rectified press the ON/OFF button.
Operating Instructions ...there are problems operating the dishwasher. Symptom Possible Cause Solution The dishwasher door has not Shut the door. been closed properly. The programme does not start. Mains plug is not plugged in. Insert mains plug. House fuse is faulty. Replace fuse. For dishwasher models with If dishes are to be washed delay start timer: immediately cancel delay Delay start has been selected. start timer. The washing compartment is made of anticorrosive stainless steel.
Operating Instructions There are streaks, milky spots or a bluish coating on glasses and dishes. – Decrease rinse aid dosing. There are dried water drops on the glasses and dishes. – Increase rinse aid dosing. – The detergent may be the cause. Contact the detergent manufacturer's consumer advisor. Technical Data Capacity: 12 place settings including serving dishes Permitted Water Pressure: 1-10 bar (=10-100 N/cm2 = 0.1-1.
Operating Instructions Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme (see Programme Table). Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see Programme Table). Full Load: 12 place settings incl. serving dishes Half Load: 6 place settings incl.
Installation and Connection Instructions INSTALLATION AND CONNECTION INSTRUCTIONS Installing the Dishwasher • The dishwasher must be installed on a firm floor and adjusted such that it is stable and level. • To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units extend the threaded feet by unscrewing: – use a screwdriver.
Installation and Connection Instructions Dishwashers That Can Be Integrated (see installation template supplied) 3 The door of the appliance can be fitted with a wooden/facing panel with the following dimensions: Width: 591 – 594 mm Thickness: 16 – 24 mm Height: (variable) dependent on – Aperture height – Plinth height – The adjustment so that the unit matches the height of the adjoining units The exact height of the adjoining units must be measured at the place of installation. Weight: max.
Installation and Connection Instructions Connecting the Dishwasher Water Connection The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations. • The dishwasher can be connected to cold and hot water supplies up to max. 60 °C. • The dishwasher must not be connected to open hot water appliances or instantaneous water heaters.
Installation and Connection Instructions Water drain Drain hose 1 The drain hose must not be kinked, crushed or entangled. • Connecting the drain hose: – Maximum permitted height: 1 metre. – Minimum required height 30 cm above the lower edge of the machine. Extension hoses • Extension hoses are available from AEG Service Force. The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded.
Installation and Connection Instructions Leak Prevention System For protection from damage due to water leaks, the dishwasher is equipped with a leak prevention system, the AQUA CONTROL SYSTEM. In the event of a fault, the safety valve immediately interrupts the supply of water to the appliance and the drain pump switches on. By this means water can neither escape nor overflow. The remaining water in the appliance is automatically pumped out.
Installation and Connection Instructions Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. 1 WARNING - This appliance must be earthed. The manufacturer declines any responsibility should these safety measures not be observed. Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. To isolate the dishwasher from the mains, remove the mains plug.
Installation and Connection Instructions Connections The water inlet and drain hoses, as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the appliance. The plumbing and electrical installation example given below can only be regarded as a recommendation.
Guarantee Conditions GUARANTEE CONDITIONS 1. 2. 3. 4. 5. 6. Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials.
Service & Spare parts SERVICE & SPARE PARTS If you wish to purchase spare parts or require an engineer, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your telephone call will be automatically routed to the Service Centre covering your post code area. When you contact the Service Centre they will need the following information: 1. Your name & address, including post code. 2. Your telephone number 3. Clear and concise details of the fault. 4.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.