FAVORIT 40730 Geschirrspülautomat Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch. Beachten Sie vor allem die Sicherheitshinweise auf den ersten Seiten dieser Benutzerinformation! Bewahren Sie bitte die Benutzerinformation zum späteren Nachschlagen auf. Geben Sie sie an eventuelle Nachbesitzer des Gerätes weiter.
Inhalt INHALT Gebrauchsanweisung ...................................... 5 Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Wirtschaftlich und umweltbewußt spülen . . . . . . . . . . . . . . . . . . . . . . . . 7 Geräteansicht und Bedienblende . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bedienblende . . .
Inhalt Pflege und Reinigung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Reinigung der Siebe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Was tun, wenn... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...Fehlermeldungen angezeigt werden. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...es Probleme beim Betrieb des Geschirrspülers gibt. . . . . . . . . . . . . . . . .
Gebrauchsanweisung GEBRAUCHSANWEISUNG 1 Sicherheitshinweise Die Sicherheit von AEG-Elektrogeräten entspricht den anerkannten Regeln der Technik und dem Gerätesicherheitsgesetz. Dennoch sehen wir uns als Hersteller veranlaßt, Sie mit folgenden Sicherheitshinweisen vertraut zu machen: Aufstellung, Anschluß, Inbetriebnahme • Der Geschirrspüler darf nur stehend transportiert werden. • Überprüfen Sie den Geschirrspüler auf Transportschäden. Ein beschädigtes Gerät auf keinen Fall anschließen.
Gebrauchsanweisung Allgemeine Sicherheit • Reparaturen am Geschirrspüler dürfen nur von Fachkräften durchgeführt werden. Durch unsachgemäße Reparaturen können erhebliche Gefahren für den Benutzer entstehen. Wenden Sie sich im Reparaturfall an unseren Kundendienst oder an Ihren Fachhändler. • Geschirrspüler nie in Betrieb nehmen, wenn Netzkabel, Zu- /Ablaufschlauch beschädigt sind oder Bedienblende, Arbeitsplatte oder der Sockelbereich so beschädigt sind, daß das Gerät offen zugänglich ist.
Gebrauchsanweisung • Im Fehlerfall zuerst Wasserhahn schließen, dann das Gerät ausschalten und Netzstecker aus der Steckdose ziehen. Bei Festanschluß: Sicherung(en) ausschalten bzw. Schraubsicherungen herausdrehen. 2 Entsorgung Verpackungsmaterial entsorgen Entsorgen Sie das Verpackungsmaterial des Geschirrspülautomaten sachgerecht. Alle verwendeten Verpackungsmaterialien sind umweltverträglich und wiederverwertbar.
Gebrauchsanweisung Geräteansicht und Bedienblende Deckendusche Gummidichtung für Ankopplung des Wasserzulaufs zum Sprüharm Sprüharme Härtebereichsschalter Vorratsbehälter für Spezialsalz Behälter für Reinigungsmittel Vorratsbehälter für Klarspüler 8 Typschild Siebe
Gebrauchsanweisung Bedienblende FunktionsTasten Startzeit einstellen ProgrammablaufAnzeige Anzeige der eingestellten Startzeit 12 3 Funktions-Taste Spülprogramm-Tasten KontrollAnzeigen EIN / AUS Taste Türgriff Funktions-Tasten: Zusätzlich zum aufgedruckten Spülprogramm können mit Hilfe dieser Tasten noch folgende Funktionen eingestellt werden: Funktions-Taste 1 Wasserenthärter einstellen Funktions-Taste 2 Klarspülerzulauf ein-, ausschalten Funktions-Taste 3 - nicht belegt - Programmablauf-An
Gebrauchsanweisung Vor der ersten Inbetriebnahme Entfernen Sie vor Inbetriebnahme alle Klammern, mit denen die Geschirrkörbe für den Transport gesichert werden. Führen Sie dann folgende Schritte durch: 1. Wasserenthärter einstellen 2. Spezialsalz für Wasserenthärter einfüllen 3. Klarspüler einfüllen 3 Spezialsalz und Klarspüler müssen nicht eingefüllt werden, wenn Sie 3-in-1 Reinigungsmitteltabletten verwenden.
Gebrauchsanweisung 1) (°d) deutscher Grad, Maß für die Wasserhärte 2) (mmol/l) Millimol pro Liter, internationale Einheit der Wasserhärte 3) Bei dieser Einstellung kann sich die Programmlaufzeit geringfügig verlängern. *) werkseitige Einstellung Wasserenthärter einstellen 0 Wasserenthärter gemäß Tabelle auf die Wasserhärte Ihres Wohngebietes einstellen: Geschirrspülautomat muss ausgeschaltet sein. Mechanische Einstellung: 1. Tür des Geschirrspülers öffnen. 2.
Gebrauchsanweisung Spezialsalz für Wasserenthärter 3 Ist die Wasserhärte in Ihrem Wohngebiet unter 4 °d, dann muß das Wasser in Ihrem Geschirrspüler nicht enthärtet werden und Sie benötigen kein Spezialsalz oder Salzersatzstoffe. Sie haben 2 Möglichkeiten, das Wasser zu enthärten: • Wenn Sie Reinigungsmittel verwenden, welches bereits Salzersatzstoffe enthält, wird nur dieses Reinigungsmittel in den Behälter für Reinigungsmittel gegeben.
Gebrauchsanweisung 3 Wenn für die Verwendung von Reinigungsmittel inkl. Spezialsalz der Wasserenthärter elektronisch auf „1“ eingestellt wird, dann wird damit die Kontroll-Anzeige für Spezialsalz abgeschaltet. Spezialsalz einfüllen Wenn Sie Reinigungsmittel und Spezialsalz getrennt verwenden, füllen Sie Spezialsalz ein: – Vor der ersten Inbetriebnahme des Geschirrspülers. – Wenn auf der Bedienblende die Kontrollanzeige für Spezialsalz J leuchtet. 0 1. Tür öffnen, Unterkorb herausnehmen. LE 2.
Gebrauchsanweisung Klarspüler Durch den Klarspüler erhält man fleckenfreies, glänzendes Geschirr und klare Gläser. Sie haben 2 Möglichkeiten, Klarspüler zuzuführen: • Wenn Sie Reinigungsmittel verwenden, welches den Klarspüler bereits enthält, wird das Reinigungsmittel inkl. Klarspüler in den Behälter für Reinigungsmittel gegeben. – In diesem Fall muss die Klarspülerzugabe aus dem Vorratsbehälter ausgeschaltet sein, um Doppeldosierung zu vermeiden.
Gebrauchsanweisung Die Anzeige L zeigt die momentane Einstellung an: Anzeige L leuchtet: Klarspülerzulauf eingeschaltet (Voreinstellung ab Werk) Anzeige L leuchtet nicht: Klarspülerzulauf ausgeschaltet 4. Drücken der Funktions-Taste 2 schaltet die Klarspülerzugabe ein bzw. aus. 5. Ist die Klarspülerzugabe richtig eingestellt, EIN/AUS-Schalter drücken. Die Einstellung für die Klarspülerzugabe ist dann gespeichert.
Gebrauchsanweisung Klarspülerdosierung einstellen Beim Geschirrspülen wird aus dem Vorratsfach Klarspüler ins Spülwasser abgegeben. Die Dosierung können Sie von 1-6 einstellen. Vom Werk ist die Dosierung auf „4“ eingestellt. Dosierung nur dann verändern, wenn auf Gläsern und Geschirr Schlieren, milchige Flecken oder angetrocknete Wassertropfen zu sehen sind. (siehe unter „Was tun, wenn...“). 0 1. Geschirrspülertür öffnen. 2. Mit Finger den Entriegelungsknopf des Klarspülerfachs drücken. 3.
Gebrauchsanweisung Im täglichen Gebrauch • Muß Spezialsalz oder Klarspüler nachgefüllt werden ? • Besteck und Geschirr in Geschirrspüler einordnen • Reinigungsmittel für Geschirrspüler einfüllen • Für Besteck und Geschirr geeignetes Spülprogramm auswählen • Spülprogramm starten Besteck und Geschirr einordnen 1 Schwämme, Haushaltstücher und alle Gegenstände, die sich mit Wasser vollsaugen können, dürfen nicht im Geschirrspüler gereinigt werden.
Gebrauchsanweisung Besteck einordnen Lange, spitze Besteckteile stellen im Besteckkorb, besonders für Kinder eine Gefahrenquelle dar (siehe Sicherheitshinweise). Damit alle Besteckteile vom Wasser umspült werden, sollten Sie 1. den Gittereinsatz auf den Besteckkorb aufstecken 2. kurze Messer, Gabeln und Löffel mit dem Griff nach unten in den Gittereinsatz des Besteckkorbs stellen.
Gebrauchsanweisung Töpfe, Pfannen und große Teller einordnen Größeres und stark verschmutztes Geschirr im Unterkorb einordnen (Teller bis 29 cm Durchmesser). Ihr Geschirrspüler hat eine der vier folgenden Varianten von Unterkörben: Variante 1: Alle Tellereinsätze des Unterkorbs sind fest Variante 2: Die rechten Tellereinsätze des Unterkorbs sind nach links klappbar Um größeres Geschirr leichter einordnen zu können, sind die beiden rechten Tellereinsätze des Unterkorbs nach links klappbar: 0 1.
Gebrauchsanweisung Variante 3: Die rechten Tellereinsätze des Unterkorbs sind überkreuz klappbar 3 Um größeres Geschirr leichter einordnen zu können, sind die beiden rechten Tellereinsätze des Unterkorbs überkreuz klappbar. Variante 4: Beide hintere Tellereinsätze des Unterkorbs sind überkreuz klappbar 3 20 Um größeres Geschirr leichter einordnen zu können, sind die beiden hinteren Tellereinsätze des Unterkorbs überkreuz klappbar.
Gebrauchsanweisung Tassen, Gläser und Kaffeeservice einordnen Kleineres, empfindliches Geschirr und lange, spitze Besteckteile im Oberkorb einordnen. • Geschirrteile auf und unter den klappbaren Tassenauflagen versetzt anordnen, damit das Spülwasser alle Geschirrteile erreicht. • Für hohe Geschirrteile lassen sich die Tassenauflagen hochklappen. • Wein-, Sekt- sowie Cognacgläser in die Ausschnitte der Tassenauflagen lehnen bzw. hängen. • Gläser, Becher usw.
Gebrauchsanweisung Oberkorb in der Höhe verstellen Maximale Höhe des Geschirrs im Oberkorb Unterkorb 3 bei angehobenem Oberkorb 22 cm 31 cm bei abgesenktem Oberkorb 24 cm 29 cm Die Höhenverstellung ist auch bei beladenen Körben möglich. Absenken des Oberkorbs 0 1. Oberkorb ganz herausziehen. 2. Oberkorb bis zum Anschlag anheben und senkrecht absenken. Der Oberkorb rastet in der unteren Position ein. Anheben des Oberkorbs 1. Oberkorb ganz herausziehen. 2.
Gebrauchsanweisung Reinigungsmittel einfüllen 1 Verwenden Sie nur Reinigungsmittel für Geschirrspüler. Füllen Sie Reinigungsmittel ein: – Vor Beginn eines Spülprogramms (nicht beim Programm Vorspülen). Reinigungsmittel wird während des Programms ins Spülwasser abgegeben. Beachten Sie bitte die Dosier- und Lagerempfehlungen der Hersteller auf den Verpackungen der Reinigungsmittel. Das Fach für Reinigungsmittel ist auf der Innenseite der Tür. 0 1.
Gebrauchsanweisung Verwendung von 3-in-1 Reinigungsmitteltabletten Allgemeine Hinweise Bei diesen Produkten handelt es sich um Tabletten mit kombinierten Reinigungsmittel-, Klarspül- und Salzfunktionen. 0 1. Vor Verwendung dieser Produkte müssen Sie zunächst prüfen, ob das Wasser in Ihrem Haushalt die richtige Härte zur Benutzung dieser Produkte aufweist, wie es die Anweisungen des Reinigungsmittelherstellers empfehlen (siehe Produktverpackung). 2.
Gebrauchsanweisung Kompaktreiniger Reinigungsmittel für Geschirrspüler lassen sich anhand ihrer chemischen Zusammensetzung in zwei Grundtypen einteilen: – herkömmliche, alkalische Reiniger mit ätzenden Bestandteilen – niederalkalische Kompaktreiniger mit natürlichen Enzymen. 2 50 °C-Spülprogramme in Verbindung mit Kompaktreinigern entlasten die Umwelt und schonen Ihr Geschirr, denn diese Spülprogramme sind speziell auf die schmutzlösenden Eigenschaften der Enzyme im Kompaktreiniger abgestimmt.
Gebrauchsanweisung Spülprogramm auswählen (Programmtabelle) Wählen Sie mit Hilfe dieser Tabelle das geeignete Spülprogramm aus: Geschirrart zusätzlich Art der Verschmutzung Geeignetes Spülprogramm: Programmablauf 1) Verbrauchswerte: 2) • stark verschmutzt • angetrocknete Speisereste, besonders Eiweiß und Stärke - - • normal verschmutzt • frisch benutzt • normal bis leicht verschmutzt besonders geeignet bei Verwendung von Kompaktreinigern.
Gebrauchsanweisung Spülprogramm starten 0 1. Überprüfen Sie, ob Geschirr und Besteck im Geschirrspüler so eingeord- net sind, dass die Sprüharme sich frei drehen können. 2. Wasserhahn ganz aufdrehen. 3. Tür schließen. 4. EIN/AUS-Taste drücken. Die Anzeige der EIN/AUS-Taste leuchtet. 5. Programmtaste für das gewünschte Programm drücken (siehe „Programmtabelle“). Die Programmanzeige leuchtet. Ein oder zwei Lampen der Programmablauf-Anzeige blinken. Nach ungefähr 3 Sekunden beginnt das gewählte Spülprogramm.
Gebrauchsanweisung Spülprogramm unterbrechen durch Öffnen der Geschirrspülertür Beim Öffnen der Tür kann heißer Dampf austreten. Verbrühungsgefahr! Tür vorsichtig öffnen. 0 1. Geschirrspülertür öffnen. Das Spülprogramm stoppt. 2. Tür schließen. Das Spülprogramm läuft weiter. 1 Spülprogramm abbrechen 0 1. Funktions-Tasten 2 und 3 drücken und gedrückt halten. Die Programmanzeige des laufenden Spülprogramms blinkt einige Sekunden und erlischt dann. 2. Funktions-Tasten loslassen.
Gebrauchsanweisung Spülprogramm wechseln nach Startzeitvorwahl: Solange das Spülprogramm nicht begonnen hat, können Sie durch Drücken einer Programmtaste das Spülprogramm noch wechseln. 0 1. Taste des neuen Spülprogramms drücken und gedrückt halten. Zunächst blinkt die Anzeige des bereits gewählten Spülprogramms. Nach einigen Sekunden leuchtet nur noch die Anzeige des neuen Spülprogramms. 2. Programm-Taste loslassen. Nach Ablauf der eingestellten Stunden startet das Spülprogramm automatisch.
Gebrauchsanweisung Pflege und Reinigung 1 Auf keinen Fall handelsübliche Möbelpflege- oder aggressive Reinigungsmittel verwenden. • Bedienteile des Geschirrspülers bei Bedarf nur mit einem weichen Lappen und warmem, klarem Wasser reinigen. • Innenbehälter, Türdichtung und Wasserzulauf gelegentlich auf Verschmutzungen kontrollieren und gegebenfalls reinigen. Reinigung der Siebe Die Siebe im Spülraumboden sind in hohem Grade selbstreinigend.
Gebrauchsanweisung 7. Flächensieb wieder in den Spülraumboden einsetzen. 8. Grob-/Feinsieb in den Mikrofilter einsetzen und zusammenstecken. 9. Siebkombination einsetzen und durch Schwenken des Griffs im Uhrzeigersinn bis zum Anschlag verriegeln. Darauf achten, daß das Flächensieb nicht über den Spülraumboden heraussteht. 1 Ohne Siebe darf auf keinen Fall gespült werden.
Gebrauchsanweisung Was tun, wenn... Versuchen Sie mit Hilfe der hier aufgeführten Hinweise kleinere Störungen am Geschirrspüler selbst zu beheben. Wenn Sie bei einer der hier aufgeführten Störungen oder zur Behebung eines Bedienfehlers den Kundendienst in Anspruch nehmen, erfolgt der Besuch des Kundendienst-Technikers auch während der Garantiezeit nicht kostenlos. ...Fehlermeldungen angezeigt werden.
Gebrauchsanweisung Störung Mögliche Ursache Abhilfe Die Programmanzeige des Der Siphon ist verstopft. Siphon reinigen. gewählten Spülprogramms blinkt, die Anzeige für SpülproWasserablaufschlauch ist Schlauchverlegung übergrammende blinkt im nicht korrekt verlegt. prüfen. Rhythmus 2 kurz aufeinanderfolgender Lichtsignale. Die Anzeige für Spülprogrammende blinkt im Das Wasserschutzsystem Rhythmus 3 kurz aufeinan- hat angesprochen. derfolgender Lichtsignale.
Gebrauchsanweisung ...es Probleme beim Betrieb des Geschirrspülers gibt. Störung Programm startet nicht. Mögliche Ursache Abhilfe Geschirrspülertür ist nicht richtig geschlossen. Tür schließen. Netzstecker ist nicht eingesteckt. Netzstecker einstecken. Sicherung der Hausinstallation ist nicht in Ordnung. Sicherung ersetzen. Bei Geschirrspülermodellen Falls Geschirr sofort gespült mit Startzeitvorwahl: werden soll, StartzeitvorEine Startzeit ist vorgewählt. wahl löschen.
Gebrauchsanweisung Auf Gläsern und Geschirr sind Schlieren, Streifen, milchige Flecken oder blauschimmernder Belag. – Klarspülerdosierung niedriger einstellen. Auf Gläsern und Geschirr sind angetrocknete Wassertropfen. – Klarspülerdosierung höher einstellen. – Der Reiniger kann die Ursache sein. Kontaktieren Sie den Kundenberater des Reinigungsmittelherstellers. Technische Daten Fassungsvermögen: 12 Maßgedecke einschließlich Servicegeschirr Zulässiger Wasserdruck: 1-10 bar (=10-100 N/cm2 = 0.1-1.
Gebrauchsanweisung Hinweise für Prüfinstitute Die Prüfung nach EN 60704 muß bei voller Beladung mit dem Testprogramm (siehe Programmtabelle) durchgeführt werden. Die Prüfungen nach EN 50242 müssen mit vollem Salzbehälter des Wasserenthärters, mit vollem Vorratsbehälter für Klarspüler und mit dem Testprogramm (siehe Programmtabelle) durchgeführt werden. Reinigerdosierung : Volle Beladung: 12 Maßgedecke einschl. Servicegeschirr Halbvolle Beladung: 6 Maßgedecke einschl.
Aufstell- und Anschlußanweisung AUFSTELL- UND ANSCHLUßANWEISUNG Aufstellen des Geschirrspülers • Geschirrspüler muß standsicher und waagrecht ausgerichtet auf festem Boden aufgestellt werden. • Um Bodenunebenheiten auszugleichen und Gerätehöhe an andere Möbel anzugleichen, Schraubfüße herausschrauben: – mit einem Schraubendreher. • Bei Unterbau-Geschirrspülern sind die hinteren Gerätefüße mit einem Schraubendreher vorne am Gerät einzustellen.
Aufstell- und Anschlußanweisung Unterbau-Geschirrspüler (siehe beiliegende Montageanleitung) Standgeräte Standgeräte lassen sich freistehend ohne zusätzliche Befestigung aufstellen. Wird der Geschirrspüler direkt neben einem Gas- oder Kohleherd aufgestellt, muß zwischen Herd und Geschirrspüler eine wärmeisolierende, nicht brennbare Platte bündig zur Oberkante der Arbeitsplatte (Tiefe 57,5 cm) angebracht werden. Die Platte sollte auf der Seite zum Herd hin mit Aluminiumfolie ausgestattet sein.
Aufstell- und Anschlußanweisung Anschließen des Geschirrspülers Wasseranschluss Der Geschirrspüler hat Sicherheitseinrichtungen, die den Rückfluss von Spülwasser in das Trinkwasser-Leitungsnetz verhindern und den geltenden wassertechnischen Sicherheitsvorschriften entsprechen. • Der Geschirrspüler kann an Kaltwasser und an Warmwasser bis max. 60 °C angeschlossen werden. • Der Geschirrspüler darf nicht an offene Warmwassergeräte und Durchlauferhitzer angeschlossen werden.
Aufstell- und Anschlußanweisung 3 Das folgende Kapitel gilt nur für Geschirrspüler, die an der Schlauchverschraubung zum Wasserhahn ein Sicherheitsventil haben: Zulaufschlauch mit Sicherheitsventil Nach Anschluss des doppelwandigen Zulaufschlauchs befindet sich das Sicherheitsventil direkt am Wasserhahn. Daher steht der Zulaufschlauch nur während des Wasserzulaufs unter Druck.
Aufstell- und Anschlußanweisung Wasserablauf Ablaufschlauch 1 Der Ablaufschlauch darf nicht geknickt, gequetscht oder in sich verschlungen sein. • Anschluß des Ablaufschlauches: – maximal zulässige Höhe: 1 Meter. – minimal erforderliche Höhe 40cm über der Geräteunterkante. Verlängerungsschläuche • Verlängerungsschläuche sind über den Fachhandel oder unseren Kundendienst zu beziehen. Der Innendurchmesser der Verlängerungsschläuche muß 19 mm betragen, damit die Gerätefunktion nicht gestört wird.
Aufstell- und Anschlußanweisung Wasserschutzsystem Zum Schutz gegen Wasserschäden ist der Geschirrspüler mit einem Wasserschutzsystem ausgestattet. Im Fehlerfall unterbricht das Sicherheitsventil im Zulaufschlauch sofort den Wasserzulauf und die Entleerungspumpe schaltet sich ein. Damit kann Wasser weder aus- noch überlaufen. Im Gerät befindliches Restwasser wird automatisch abgepumpt. 1 Das Wasserschutzsystem funktioniert auch, wenn das Gerät ausgeschaltet ist.
Aufstell- und Anschlußanweisung Anschlußtechnik Zulauf- und Ablaufschläuche sowie das Netzkabel müssen seitlich vom Geschirrspüler angeschlossen werden, da hinter dem Gerät kein Platz dafür ist. Das nachfolgende Beispiel einer Sanitär- und Elektroinstallation kann nur eine Empfehlung sein, da maßgebend die Gegebenheiten am Aufstellort sind (vorhandene Anschlüsse, örtliche Anschlußvorschriften der Energie- bzw. der Wasserwerke, usw...).
Kundendienststellen KUNDENDIENSTSTELLEN Deutschland Sehr geehrter Kunde, der Werkskundendienst von AEG Hausgeräte ist dezentral organisiert. Damit bieten wir Ihnen überall einen zuverlässigen Service. Unter der für Sie kostengünstigen Rufnummer 0180 322 66 22 (EUR 0.09 / Minute) Deutsche Telekom/ Stand Jan. 2002 können Sie im Bedarfsfall einen unserer Spezialisten oder Service-Partner anfordern. Ihre Ersatzteil-Bestellung geben Sie bitte unter der zentralen Rufnummer 0180 5 00 10 76 auf. (EUR 0.
Kundendienststellen PLZ Adresse 41541 Dormagen-St. Peter Sachtlebenstraße 1 46562 Voerde* Friedrich-Wilhelm-Straße 22 48165 Münster* Zum Kaiserbusch 1 49084 Osnabrück* Pferdestraße 23 52068 Aachen* Auf der Hüls 197 56068 Koblenz* Rheinstraße 17 56070 Koblenz* A.-Hosch-Str.
Kundendienststellen Weitere Service-Stellen sind in: 46 03222 Groß Klessow 06896 Wittenberg-Reinsdorf 15517 Fürstenwalde 16515 Oranienburg 17039 Ihlenfeld 19057 Schwerin 24354 Rieseby 26639 Wiesmoor 27726 Worpswede 30900 Wedemark 32825 Blomberg 34497 Korbach 36043 Fulda 39114 Magdeburg 49377 Vechta 63906 Erlenbach 78244 Bietingen 84307 Eggenfelden 87549 Rettenberg 99819 Ettenhausen
Kundendienststellen Österreich Unsere Kundendienststellen und Servicepartner Electrolux stellt Ihnen hiermit jene Partner vor, die dafür garantieren, dass wir Ihnen Top-Qualität mit unseren Kundendiensteinrichtungen jetzt und in Zukunft bieten. Unsere Kundendienststellen in den Bundesländern sind spezialisiert auf unsere Marken: AEG, Electrolux, Juno, Zanussi. Zentrale: Kundendienst Wien, Niederösterreich, nördliches Burgenland Electrolux Hausgeräte GmbH 1230 Wien, Herziggasse 9 Tel.
Kundendienststellen Kundendienststelle Tirol BEP! Hausgeräte-Kundendienst GesmbH 6020 Innsbruck, Amraser Straße 118 Tel. Fax Internet: bep.innsbruck@aon.at Kundendienststelle Vorarlberg Walter Stecher Elektroinstallationen 6912 Hörbranz, Lochauerstraße 2 Tel. Fax Internet: stewa.strom@utanet.at 0512/392153 0512/392153-29 05573/83651 05573/83651-14 Belgien Adresse Electrolux Home Products Belgium ELECTROLUX SERVICE Bergensesteenweg, 719 1502 Lembeek Province de Liège: S.D.E.
Garantiebedingungen GARANTIEBEDINGUNGEN Deutschland Der Endabnehmer dieses Gerätes (Verbraucher) hat bei einem Kauf dieses Gerätes von einem Unternehmer (Händler) in Deutschland im Rahmen der Vorschriften über den Verbrauchsgüterkauf gesetzliche Rechte, die durch diese Garantie nicht eingeschränkt werden. Diese Garantie räumt dem Verbraucher also zusätzliche Rechte ein.
Garantiebedingungen Österreich Sehr geehrte Kunden! Wir, die Electrolux Hausgeräte GmbH, beglückwünschen Sie zum Erwerb eines Gerätes aus dem Electrolux Konzern. Für dieses Gerät räumen wir Ihnen, gemäß den nachstehenden Bedingungen, eine besondere Garantie ein, die Ihnen also zusätzliche Rechte gewährt. 1. Die Garantie beginnt mit dem Tag an dem das Gerät gekauft wurde und erstreckt sich über einen Zeitraum von 24 Monaten. Wir empfehlen daher, den Kaufbeleg unbedingt aufzubewahren. 2.
Garantiebedingungen Belgien Unsere Geräte werden mit größter Sorgfalt hergestellt. Trotzdem kann es einmal zu einem Defekt kommen. Unser Kundendienst übernimmt auf Anfrage gerne die Reparatur, und zwar sowohl während des Garantiezeitraums als auch danach. So ist gewährleistet, dass ein Defekt nicht zu einer Verkürzung der Lebensdauer des Geräts führt. Die vorliegenden Garantiebedingungen beruhen auf der Richtlinie der Europäischen Union 99/44/EG sowie den Bestimmungen des Bürgerlichen Gesetzbuches.
Garantiebedingungen 12. Wenn während des Garantiezeitraums eine wiederholte Reparatur ein und desselben Defekts zu keinem befriedigenden Ergebnis führt, oder bei unverhältnismäßig hohen Reparaturkosten kann, in Abstimmung mit dem Kunden, ein Austausch des defekten Geräts durch ein gleichwertiges anderes erfolgen. In diesem Fall behalten wir uns das Recht vor, vom Kunden eine finanzielle Beteiligung zu verlangen, die anteilig zum verstrichenen Nutzungszeitraum berechnet wird. 13.
Service SERVICE Im Kapitel „Was tun, wenn...“ sind die wichtigsten Fehlerquellen zusammengestellt, die Sie selbst beheben können. Wenn Sie trotzdem für einen der aufgeführten Hinweise oder aufgrund von Fehlbedienung den Kundendienst in Anspruch nehmen, so erfolgt der Besuch des Kundendienst-Technikers auch während der Garantiezeit nicht kostenlos. Wenn Sie für eine Störung keinen Hinweis in dieser Gebrauchsanweisung finden, wenden Sie sich bitte an den Kundendienst.
From the Electrolux Group. The world´s No.1 choice. Die Electrolux-Gruppe ist der weltweit größte Hersteller von gas- und strombetriebenen Geräten für die Küche, zum Reinigen und für Forst und Garten. Jedes Jahr verkauft die Electrolux-Gruppe in über 150 Ländern der Erde über 55 Millionen Produkte (Kühlschränke, Herde, Waschmaschinen, Staubsauger, Motorsägen und Rasenmäher) mit einem Wert von rund 14 Mrd. USD. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.