ÖKO_FAVORIT 41700 Geschirrspülautomat Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch. Beachten Sie vor allem die Sicherheitshinweise auf den ersten Seiten dieser Benutzerinformation! Bewahren Sie bitte die Benutzerinformation zum späteren Nachschlagen auf. Geben Sie sie an eventuelle Nachbesitzer des Gerätes weiter.
Inhalt INHALT Gebrauchsanweisung ...................................... 5 Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Wirtschaftlich und umweltbewußt spülen . . . . . . . . . . . . . . . . . . . . . . . . 7 Geräteansicht und Bedienblende . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bedienblende . . .
Inhalt Aufstell- und Anschlußanweisung Aufstellen des Geschirrspülers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Integrierbarer Geschirrspüler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unterbau-Geschirrspüler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standgeräte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 30 30 30 Anschließen des Geschirrspülers . . . . . . . . . .
Gebrauchsanweisung GEBRAUCHSANWEISUNG 1 Sicherheitshinweise Die Sicherheit von AEG-Elektrogeräten entspricht den anerkannten Regeln der Technik und dem Gerätesicherheitsgesetz. Dennoch sehen wir uns als Hersteller veranlaßt, Sie mit folgenden Sicherheitshinweisen vertraut zu machen: Aufstellung, Anschluß, Inbetriebnahme • Der Geschirrspüler darf nur stehend transportiert werden. • Überprüfen Sie den Geschirrspüler auf Transportschäden. Ein beschädigtes Gerät auf keinen Fall anschließen.
Gebrauchsanweisung Allgemeine Sicherheit • Reparaturen am Geschirrspüler dürfen nur von Fachkräften durchgeführt werden. Durch unsachgemäße Reparaturen können erhebliche Gefahren für den Benutzer entstehen. Wenden Sie sich im Reparaturfall an unseren Kundendienst oder an Ihren Fachhändler. • Geschirrspüler nie in Betrieb nehmen, wenn Netzkabel, Zu- /Ablaufschlauch beschädigt sind oder Bedienblende, Arbeitsplatte oder der Sockelbereich so beschädigt sind, daß das Gerät offen zugänglich ist.
Gebrauchsanweisung • Im Fehlerfall zuerst Wasserhahn schließen, dann das Gerät ausschalten und Netzstecker aus der Steckdose ziehen. Bei Festanschluß: Sicherung(en) ausschalten bzw. Schraubsicherungen herausdrehen. 2 Entsorgung Verpackungsmaterial entsorgen Entsorgen Sie das Verpackungsmaterial des Geschirrspülautomaten sachgerecht. Alle verwendeten Verpackungsmaterialien sind umweltverträglich und wiederverwertbar.
Gebrauchsanweisung Geräteansicht und Bedienblende Deckendusche Gummidichtung für Ankopplung des Wasserzulaufs zum oberen Sprüharm Sprüharme Vorratsbehälter für Spezialsalz Vorratsbehälter für Klarspüler Behälter für Reinigungsmittel Typschild Siebe 8
Gebrauchsanweisung Bedienblende Funktions- EnthärterTaste Taste Kontrollanzeigen Türgriff Anzeige der einzelnen Spülprogrammschritte Bedienfeld Das Bedienfeld besteht aus dem EIN/AUS-Schalter und den Programmtasten mit LED-Anzeigen. Enthärter- und Funktions-Taste: Zusätzlich zum aufgedruckten Spülprogramm kann durch die Kombination dieser Tasten der Wasserenthärter des Geschirrspülers eingestellt werden.
Gebrauchsanweisung Wasserenthärter einstellen Um Kalkablagerungen auf Geschirr und im Geschirrspüler zu verhindern, muß das Geschirr mit weichem, d.h. kalkarmen Wasser gespült werden. Daher hat der Geschirrspüler einen Wasserenthärter, in dem Leitungswasser ab einer Härte von 4 °d (deutscher Grad) mit Hilfe von Spezialsalz entkalkt wird. 3 0 Über Wasserhärte und Härtebereich in Ihrem Wohngebiet informiert Sie das zuständige Wasserwerk.
Gebrauchsanweisung 5. Drücken der Enthärter-Taste erhöht die Härtestufe um 1. (Ausnahme: Nach Härtestufe 9 folgt Härtestufe 0). 6. Ist die Härtestufe richtig eingestellt, EIN/AUS-Schalter drücken. Die Härtestufe ist dann gespeichert. Spezialsalz für Wasserenthärter einfüllen 1 Verwenden Sie nur Spezialsalz für Geschirrspüler. Füllen Sie niemals andere Salzarten (z.B. Speisesalz) oder Geschirrspülreiniger in den Salzvorratsbehälter. Dies würde den Wasserenthärter zerstören.
Gebrauchsanweisung Deshalb nach dem Einfüllen des Spezialsalzes ein Spülprogramm ablaufen lassen. Dadurch werden übergelaufenes Salzwasser und Salzkörner ausgespült. 3 Je nach Körnung kann es einige Stunden dauern, bis das Salz sich im Wasser aufgelöst hat und die Kontrollanzeige SALZ wieder erlischt. Die Einstellung des Wasserenthärters und damit der Salzverbrauch sind abhängig von der örtlichen Wasserhärte.
ax 6 5 4 1 32 3. Klarspüler einfüllen; maximal bis zur gestrichelten Linie, das entspricht einer Füllmenge von ca. 150 ml 4. Deckel wieder einsetzen und im Uhrzeigersinn festdrehen. 5. Wenn Klarspüler danebengelaufen ist, mit einem Lappen wegwischen. Sonst bildet sich beim Spülen zuviel Schaum. m Gebrauchsanweisung Klarspülerdosierung einstellen Beim Geschirrspülen wird aus dem Vorratsbehälter Klarspüler ins Spülwasser abgegeben. Die Dosierung können Sie von 1-6 einstellen.
Gebrauchsanweisung Im täglichen Gebrauch • Muß Spezialsalz oder Klarspüler nachgefüllt werden ? • Besteck und Geschirr in Geschirrspüler einordnen • Reinigungsmittel für Geschirrspüler einfüllen • Für Besteck und Geschirr geeignetes Spülprogramm auswählen • Spülprogramm starten Besteck und Geschirr einordnen 1 Schwämme, Haushaltstücher und alle Gegenstände, die sich mit Wasser vollsaugen können, dürfen nicht im Geschirrspüler gereinigt werden.
Gebrauchsanweisung – um Glasschäden zu vermeiden, dürfen Gläser sich nicht berühren – kleine Gegenstände (z. B. Deckel) in den Besteckkorb legen Besteck einordnen Lange, spitze Besteckteile stellen im Besteckkorb, besonders für Kinder eine Gefahrenquelle dar (siehe Sicherheitshinweise). Sie müssen daher in den Oberkorb gelegt werden. Damit alle Besteckteile vom Wasser umspült werden, sollten Sie 1. den Gittereinsatz auf den Besteckkorb aufstecken 2.
Gebrauchsanweisung Töpfe, Pfannen und große Teller einordnen Größeres und stark verschmutztes Geschirr im Unterkorb einordnen. Um größeres Geschirr leichter einordnen zu können, sind bei einigen Geschirrspülermodellen die beiden Reihen des rechten Tellereinsatzes klappbar: 0 1. Rechte Tellereinsätze hinten leicht anheben. 3 2. Tellereinsätze nach links umklappen.
Gebrauchsanweisung Tassen, Gläser und Kaffeeservice einordnen Kleineres, empfindliches Geschirr und lange, spitze Besteckteile im Oberkorb einordnen. • Geschirrteile auf und unter den klappbaren Tassenauflagen versetzt anordnen, damit das Spülwasser alle Geschirrteile erreicht. • Für hohe Geschirrteile lassen sich die Tassenauflagen hochklappen. • Wein-, Sekt- sowie Cognacgläser in die Ausschnitte der Tassenauflagen lehnen bzw. hängen. • Gläser, Becher usw.
Gebrauchsanweisung Reinigungsmittel einfüllen 1 Verwenden Sie nur Reinigungsmittel für Geschirrspüler. Füllen Sie Reinigungsmittel ein: – Vor Beginn eines Spülprogramms (nicht beim Programm Vorspülen). Reinigungsmittel wird während des Programms ins Spülwasser abgegeben. Beachten Sie bitte die Dosier- und Lagerempfehlungen der Hersteller auf den Verpackungen der Reinigungsmittel. Der Behälter für Reinigungsmittel ist auf der Innenseite der Tür. 0 1.
Gebrauchsanweisung Bio-Spülprogramme und Kompaktreiniger Reinigungsmittel für Geschirrspüler lassen sich anhand ihrer chemischen Zusammensetzung in zwei Grundtypen einteilen: – herkömmliche, alkalische Reiniger mit ätzenden Bestandteilen – niederalkalische Kompaktreiniger mit natürlichen Enzymen.
Gebrauchsanweisung Spülprogramm auswählen (Programmtabelle) Wählen Sie mit Hilfe dieser Tabelle das geeignete Spülprogramm aus: Geschirrart Eß- und Kochgeschirr zusätzlich - Art der Verschmutzung • stark verschmutzt • angetrocknete Speisereste mit temperaturempfindlichem Geschirr • normal verschmutzt Dessert- und Kaffeegeschirr Alle Geschirrarten mit empfindlichen Gläsern - • leicht verschmutzt besonders geeignet bei Verwendung von Kompaktreinigern.
Gebrauchsanweisung Spülprogramm starten 0 1. Überprüfen Sie, ob Geschirr und Besteck im Geschirrspüler so eingeord- net sind, daß die Sprüharme sich frei drehen können. 2. Wasserhahn ganz aufdrehen. 3. Tür schließen. 4. EIN/AUS-Taste drücken. Anzeige der EIN/AUS-Taste leuchtet. 5. Programmtaste für das gewünschte Programm drücken (siehe „Programmtabelle“). Programmanzeige leuchtet. Nach ungefähr 6 Sekunden beginnt das gewählte Spülprogramm.
Gebrauchsanweisung Spülprogramm unterbrechen durch Öffnen der Geschirrspülertür Beim Öffnen der Tür kann heißer Dampf austreten. Verbrühungsgefahr! Tür vorsichtig öffnen. 0 1. Geschirrspülertür öffnen. Das Spülprogramm stoppt. 2. Anzeige des laufenden Spülprogramms erlischt. 3. Tür schließen. Das Spülprogramm läuft weiter. 1 Spülprogramm abbrechen 0 1. Taste des laufenden Spülprogramms drücken und gedrückt halten. Die Programmanzeige des laufenden Spülprogramms blinkt einige Sekunden und erlischt dann.
Gebrauchsanweisung Geschirrspüler ausschalten Geschirrspüler erst ausschalten, wenn in der Programmablaufanzeige ENDE aufleuchtet. 0 1. EIN/AUS-Taste drücken. Anzeige der EIN/AUS-Taste erlischt. Beim Öffnen der Tür, unmittelbar nach Programmende, kann heißer Dampf austreten. Deshalb: 2. Tür vorsichtig öffnen. 1 Geschirr ausräumen 3 • Heißes Geschirr ist stoßempfindlich. Geschirr deshalb vor dem Ausräumen abkühlen lassen.
Gebrauchsanweisung Reinigung der Siebe Die Siebe im Spülraumboden sind in hohem Grade selbstreinigend. Trotzdem sollten diese gelegentlich kontrolliert und gereinigt werden. Verschmutzte Siebe beeinträchtigen das Spülergebnis. 0 1. Tür öffnen, Unterkorb herausnehmen. 2. Das Siebsystem des Geschirrspülers besteht aus Grob-/Feinsieb, Mikrofilter und Flächensieb. Mit Griff des Mikrofilters das Siebsystem entriegeln und entnehmen. 3.
Gebrauchsanweisung Was tun, wenn... Versuchen Sie mit Hilfe der hier aufgeführten Hinweise kleinere Störungen am Geschirrspüler selbst zu beheben. Wenn Sie bei einer der hier aufgeführten Störungen oder zur Behebung eines Bedienfehlers den Kundendienst in Anspruch nehmen, erfolgt der Besuch des Kundendienst-Technikers auch während der Garantiezeit nicht kostenlos. ...Fehlermeldungen angezeigt werden. • Blinkt in der Programmablaufanzeige ENDE oder TROCKNEN, können Sie den Fehler eventuell selbst beheben.
Gebrauchsanweisung ...es Probleme beim Betrieb des Geschirrspülers gibt. Störung Programm startet nicht. Mögliche Ursache Abhilfe Geschirrspülertür ist nicht richtig geschlossen. Tür schließen. Netzstecker ist nicht eingesteckt. Netzstecker einstecken. Sicherung der Hausinstallation ist nicht in Ordnung. Sicherung ersetzen. Falls Geschirr sofort gespült werden soll, bei Geräten Bei Geschirrspülermodellen - mit Multidisplay die Startmit Startzeitvorwahl: zeit auf 0 Stunden stellen.
Gebrauchsanweisung Das Geschirr wird nicht trocken und bleibt ohne Glanz. – Es wurde kein Marken-Klarspüler verwendet. – Vorratsbehälter für den Klarspüler ist leer. Auf Gläsern und Geschirr sind Schlieren, Streifen, milchige Flecken oder blauschimmernder Belag. – Klarspülerdosierung niedriger einstellen. Auf Gläsern und Geschirr sind angetrocknete Wassertropfen. – Klarspülerdosierung höher einstellen. – Der Reiniger kann die Ursache sein. Kontaktieren Sie den Kundenberater des Reinigungsmittelherstellers.
Gebrauchsanweisung Hinweise für Prüfinstitute Vor den Prüfungen muß der Salzbehälter des Wasserenthärters und der Vorratsbehälter für Klarspüler voll aufgefüllt werden. Prüfnorm: EN 5O 242 Vergleichsprogramm: Normal BIO 50 °C für volle und halbvolle Beladung Volle Beladung: 12 Maßgedecke einschl. Servicegeschirr Reinigerdosierung: 30g (Typ B) in den Behälter für Reinigungsmittel Halbvolle Beladung: 6 Maßgedecke einschl.
Aufstell- und Anschlußanweisung AUFSTELL- UND ANSCHLUßANWEISUNG Aufstellen des Geschirrspülers • Geschirrspüler muß standsicher und waagrecht ausgerichtet auf festem Boden aufgestellt werden. • Um Bodenunebenheiten auszugleichen und Gerätehöhe an andere Möbel anzugleichen, Schraubfüße herausschrauben. Je nach Ausführung der Schraubfüße entweder – mit einem Gabelschlüssel oder – mit einem Schraubendreher.
Aufstell- und Anschlußanweisung • Je nach Bauform sind die Geschirrspüler wie folgt aufzustellen: Integrierbarer Geschirrspüler (siehe beiliegende Montageschablone) 3 Die Gerätetür kann mit einer Holzplatte/Möbelplatte folgender Abmessungen verkleidet werden: Breite: 591 – 594 mm Dicke: 16 – 24 mm Höhe: abhängig von (variabel) – Nischenhöhe – Sockelhöhe – Anpassung an Fugenverlauf benachbarter Möbel Das genaue Höhenmaß muß am Aufstellort von den benachbarten Möbeln abgemessen werden. Gewicht: max.
Aufstell- und Anschlußanweisung • Soll der Geschirrspüler unter eine Küchenarbeitsplatte eingebaut werden, muß die Original-Arbeitsplatte des Geschirrspülers wie folgt entfernt werden: – Schrauben (1) aus den Winkelstücken an der Rückseite herausdrehen . – Arbeitsplatte des Geräts ca. 1cm nach hinten schieben (2), vorne anheben (3) und wegnehmen. – Auf die im Bild gezeigte Stelle (4) der Halterung der Arbeitsplatte drücken und Halterung schräg nach hinten herausziehen (5).
Aufstell- und Anschlußanweisung Anschließen des Geschirrspülers Wasseranschluß Der Geschirrspüler hat Sicherheitseinrichtungen, die den Rückfluß von Spülwasser in das Trinkwasser-Leitungsnetz verhindern und den geltenden wassertechnischen Sicherheitsvorschriften entsprechen. • Der Geschirrspüler kann an Kaltwasser und an Warmwasser bis max. 60 °C angeschlossen werden. • Der Geschirrspüler darf nicht an offene Warmwassergeräte und Durchlauferhitzer angeschlossen werden.
Aufstell- und Anschlußanweisung Wasserablauf Ablaufschlauch 1 Der Ablaufschlauch darf nicht geknickt, gequetscht oder in sich verschlungen sein. • Anschluß des Ablaufschlauches: – maximal zulässige Höhe: 1 Meter. – minimal erforderliche Höhe 30cm über der Geräteunterkante. Verlängerungsschläuche • Verlängerungsschläuche sind über den Fachhandel oder unseren Kundendienst zu beziehen. Der Innendurchmesser der Verlängerungsschläuche muß 19 mm betragen, damit die Gerätefunktion nicht gestört wird.
Aufstell- und Anschlußanweisung Wasserschutzsystem Zum Schutz gegen Wasserschäden ist der Geschirrspüler mit einem Wasserschutzsystem, dem AQUA CONTROL SYSTEM ausgestattet. Im Fehlerfall unterbricht das Sicherheitsventil im Gerät sofort den Wasserzulauf und die Entleerungspumpe schaltet sich ein. Damit kann Wasser weder aus- noch überlaufen. Im Gerät befindliches Restwasser wird automatisch abgepumpt.
Aufstell- und Anschlußanweisung Anschlußtechnik Zulauf- und Ablaufschläuche sowie das Netzkabel müssen seitlich vom Geschirrspüler angeschlossen werden, da hinter dem Gerät kein Platz dafür ist. Das nachfolgende Beispiel einer Sanitär- und Elektroinstallation kann nur eine Empfehlung sein, da maßgebend die Gegebenheiten am Aufstellort sind (vorhandene Anschlüsse, örtliche Anschlußvorschriften der Energie- bzw. der Wasserwerke, usw...).
Kundendienststellen KUNDENDIENSTSTELLEN Sehr geehrter Kunde, der Werkskundendienst von AEG Hausgeräte ist dezentral organisiert. Damit bieten wir Ihnen überall einen zuverlässigen Service. Unter der für Sie kostenlosen Rufnummer 0800 234 73 78 können Sie im Bedarfsfall einen unserer Spezialisten oder Service-Partner anfordern. Ihre Ersatzteil-Bestellung geben Sie bitte unter der zentralen Rufnummer 0180 5 00 10 76 (DM -.24/Min.) auf. Für Störungen an Gefriergeräten bzw.
Kundendienststellen PLZ Adresse 66115 Saarbrücken-Malstatt* 67663 Kaiserslautern* Pariser Straße 200 68309 Mannheim-Käfertal Heppenheimer Straße 31-33 71034 Böblingen-Hulb Dornierstraße 7 76185 Karlsruhe-Mühlburg* Neureuther Straße 5-7 79108 Freiburg* Tullastraße 84 80634 München-Neuhausen Arnulfstraße 205 86159 Augsburg* Piccardstraße 15a 87437 Kempten* Brodkorbweg 22 Ludwigstraße 55-57 88213 Ravensburg* Henri-Dunant-Straße 6 90429 Nürnberg Muggenhofer Straße 135 91788 P
Garantiebedingungen GARANTIEBEDINGUNGEN 1. 2. 3. 4. 5. Für dieses Gerät leisten wir - zusätzlich zu der gesetzlichen Gewährleistung des Händlers aus Kaufvertrag - dem Endabnehmer gegenüber zu den nachstehenden Bedingungen Garantie: Die Garantiezeit beträgt 12 Monate und beginnt mit dem Zeitpunkt der Übergabe des Gerätes, der durch Rechnung oder andere Unterlagen zu belegen ist.
Service SERVICE Im Kapitel „Was tun, wenn...“ sind die wichtigsten Fehlerquellen zusammengestellt, die Sie selbst beheben können. Wenn Sie trotzdem für einen der aufgeführten Hinweise oder aufgrund von Fehlbedienung den Kundendienst in Anspruch nehmen, so erfolgt der Besuch des Kundendienst-Technikers auch während der Garantiezeit nicht kostenlos.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.