FAVORIT 44070 U Geschirrspülautomat Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf. Geben Sie diese Benutzerinformation an eventuelle Nachbesitzer des Gerätes weiter. 1 3 2 2 Folgende Symbole werden im Text verwendet: Sicherheitshinweise Warnung! Hinweise, die Ihrer persönlichen Sicherheit dienen. Achtung! Hinweise, die zur Vermeidung von Schäden am Gerät dienen.
Inhalt Gebrauchsanweisung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Sicherheit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Geräteansicht . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Bedienfeld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Vor der ersten Inbetriebnahme . . . . . . .
Gebrauchsanweisung 1 Sicherheit Vor der ersten Inbetriebnahme • Beachten Sie die „Aufstell- und Anschlussanweisung“. Bestimmungsgemäße Verwendung • Geschirrspüler ist nur zum Spülen von Haushaltsgeschirr bestimmt. • Umbauten oder Veränderungen am Geschirrspüler sind nicht zulässig. • Nur Spezialsalz, Reinigungs- sowie Klarspülmittel verwenden, die für Haushaltsgeschirrspüler geeignet sind. • Keine Lösungsmittel in den Geschirrspüler geben.
Geräteansicht Decken-Dusche Oberkorb-Sprüharm und Boden-Sprüharm Härtebereichsschalter Vorratsbehälter für Spezialsalz Behälter für Reinigungsmittel Vorratsbehälter für Klarspüler Typschild Siebe Bedienfeld EIN / AUS-Taste Mit der EIN-/AUS-Taste wird der Geschirrspüler ein-/ausgeschaltet.
Programm-Tasten Spülprogrammende-Anzeige ProgrammablaufAnzeigen 1 2 3 Funktions-Tasten Zeitvorwahl einstellen 3in1 Funktion auswählen KontrollAnzeigen Mit den Programm-Tasten wird das gewünschte Spülprogramm gewählt.
Vor der ersten Inbetriebnahme 3 Wenn Sie 3in1 Reiniger verwenden wollen: - Lesen Sie zuerst den Abschnitt „Verwendung von 3in1 Reinigern“. - Füllen Sie weder Spezialsalz noch Klarspüler ein. Wenn Sie keinen 3in1 Reiniger verwenden, vor der ersten Inbetriebnahme: 1. Wasserenthärter einstellen 2. Spezialsalz für Wasserenthärter einfüllen 3. Klarspüler einfüllen Wasserenthärter einstellen 3 Wasserenthärter muss mechanisch und elektronisch eingestellt werden.
3 Elektronische Einstellung: 1. EIN/AUS-Taste drücken. Falls Anzeigen der Spülprogrammtasten leuchten, ist ein Spülprogramm aktiviert. Das Spülprogramm muss abgewählt werden: Funktionstasten 2 und 3 für ca. 2 Sekunden gleichzeitig drücken. Alle zusätzlichen Anzeigen der Spülprogrammtasten erlöschen. 2. Funktions-Taste 2 und 3 gleichzeitig drücken und gedrückt halten. Die LED-Anzeigen der Funktions-Tasten 1 bis 3 blinken. 3. Funktions-Taste 1 drücken. Die LED-Anzeige der Funktions-Taste 1 blinkt.
Spezialsalz einfüllen 3 3 Um den Wasserenthärter zu entkalken, muss Spezialsalz eingefüllt werden. Nur Spezialsalz verwenden, das für Haushaltsgeschirrspüler geeignet ist. Wenn Sie keinen 3in1 Reiniger verwenden, füllen Sie Spezialsalz ein: – Vor der ersten Inbetriebnahme des Geschirrspülers. – Wenn auf dem Bedienfeld die Kontrollanzeige für Spezialsalz leuchtet. 1. Tür öffnen, Unterkorb herausnehmen. 2. Verschlusskappe des Salzvorratsbehälters entgegen dem Uhrzeigersinn aufdrehen. 3.
Klarspüler einfüllen Da der Klarspüler das Spülwasser besser ablaufen lässt, erhält man fleckenfreies, glänzendes Geschirr und klare Gläser. Wenn Sie keinen 3in1 Reiniger verwenden, füllen Sie Klarspüler ein: – Vor der ersten Inbetriebnahme des Geschirrspülers. – Wenn auf dem Bedienfeld die Kontrollanzeige für Klarspüler leuchtet. Verwenden Sie nur Spezialklarspüler für Geschirrspüler und keine anderen flüssigen Reinigungsmittel. 1. Tür öffnen.
Klarspülerdosierung einstellen 3 Dosierung nur dann verändern, wenn auf Gläsern und Geschirr Schlieren, milchige Flecken (Dosierung niedriger einstellen) oder angetrocknete Wassertropfen (Dosierung höher einstellen) zu sehen sind (siehe Kapitel „Wenn das Spülergebnis nicht zufriedenstellend ist“). Die Dosierung kann von 1-6 eingestellt werden. Vom Werk ist die Dosierung auf „4“ voreingestellt. 1. Geschirrspülertür öffnen. 2. Entriegelungsknopf des Klarspülerfachs drücken. 3. Deckel aufklappen. 4.
Im täglichen Gebrauch Besteck und Geschirr einordnen 1 Schwämme, Haushaltstücher und alle Gegenstände, die sich mit Wasser vollsaugen können, dürfen nicht im Geschirrspüler gereinigt werden. Kunststoff- und teflonbeschichtetes Geschirr hält Wassertropfen verstärkt zurück. Daher trocknet dieses Geschirr etwas schlechter als Porzellan und Edelstahl.
Besteck einordnen 1 Warnung: Spitze Messer und scharfkantige Besteckteile müssen wegen Verletzungsgefahr in den Oberkorb gelegt werden. Damit alle Besteckteile im Besteckkorb vom Wasser umspült werden, sollten Sie: 1.Gittereinsatz auf den Besteck- 2.Gabeln und Löffel mit dem Griff korb aufstecken nach unten in den Gittereinsatz des Besteckkorbs stellen. Für größere Besteckteile, wie z.B. Schneebesen, kann eine Hälfte des Besteckgitters weggelassen werden.
Um größeres Geschirr leichter einordnen zu können, sind die beiden rechten Tellereinsätze des Unterkorbs klappbar. Tassen, Gläser, Kaffeeservice Kleineres, empfindliches Geschirr und lange, spitze Besteckteile im Oberkorb einordnen. • Geschirrteile auf und unter den klappbaren Tassenauflagen versetzt anordnen, damit das Spülwasser alle Geschirrteile erreicht. • Für hohe Geschirrteile lassen sich die Tassenauflagen hochklappen. • Wein-oder Cognacgläser in die Ausschnitte der Tassenauflagen lehnen bzw.
Oberkorb in der Höhe verstellen Maximale Höhe des Geschirrs im 3 Oberkorb Unterkorb bei angehobenem Oberkorb 22 cm 30 cm bei abgesenktem Oberkorb 24 cm 29 cm Die Höhenverstellung ist auch bei beladenen Körben möglich. Je nach Modell ist das Gerät mit dem Oberkorb „Variante 1“ oder „Variante 2“ ausgestattet: Variante 1 Anheben / Absenken des Oberkorbs 1. Oberkorb ganz herausziehen. 2. Oberkorb bis zum Anschlag anheben und senkrecht absenken. Der Oberkorb rastet in der unteren bzw.
Reinigungsmittel einfüllen 1 Reinigungsmittel lösen die Verschmutzungen von Geschirr und Besteck. Das Reinigungsmittel muss vor Programmbeginn eingefüllt werden. Verwenden Sie nur Reinigungsmittel für Haushaltsgeschirrspüler. Das Fach für Reinigungsmittel ist auf der Innenseite der Tür. 1. Falls der Deckel geschlossen ist: Entriegelungsknopf drücken. Deckel springt auf. 3 16 2. Reinigungsmittel in den Behälter für Reinigungsmittel füllen.
Kompaktreiniger 2 Reinigungsmittel für Geschirrspüler sind heute fast ausschließlich niederalkalische Kompaktreiniger mit natürlichen Enzymen in Tablettenoder Pulverform. 50 °C-Spülprogramme in Verbindung mit diesen Kompaktreinigern entlasten die Umwelt und schonen Ihr Geschirr, denn diese Spülprogramme sind speziell auf die schmutzlösenden Eigenschaften der Enzyme im Kompaktreiniger abgestimmt.
Verwendung von 3in1 Reinigern 3 3 Bei diesen Produkten handelt es sich um Reiniger mit kombinierten Reinigungsmittel-, Klarspül- und Salzfunktionen. Mit dem Einschalten der 3in1-Funktion – wird die Zugabe von Spezialsalz und Klarspüler aus dem jeweiligen Vorratsbehälter unterbunden. – wird Salz- und Klarspülermangel nicht mehr angezeigt. – können die Spülprogramme bis zu 30 Minuten länger dauern. Wenn Sie 3in1 Reiniger verwenden wollen, prüfen Sie, ob diese Reiniger für Ihre Wasserhärte geeignet sind.
Spülprogramm auswählen (Programmtabelle) - • • • 120 - 130 1,8 - 2,0 23 - 25 • • • • 0,95 - 1,05 14 - 16 Wasser (Liter) • 30 MIN.
Programmwahl Wenn Ihr Geschirr so aussieht, wählen Sie ein Intensiv-Programm. ein Normal- oder Energiesparprogramm. ein Kurzprogramm (z.B. 30min-Programm).
Spülprogramm starten 1. Überprüfen, ob sich die Sprüharme frei drehen können. 2. Wasserhahn ganz aufdrehen. 3. Tür schließen. 4. EIN/AUS-Taste drücken. 5. Gewünschtes Programm wählen. Die Programmanzeige leuchtet. Nach ungefähr 3 Sekunden beginnt das gewählte Spülprogramm. Spülprogramm unterbrechen oder abbrechen Unterbrechen Sie ein laufendes Spülprogramm nur, wenn es unbedingt notwendig ist. 1 Spülprogramm unterbrechen durch Öffnen der Geschirrspülertür Beim Öffnen der Tür kann heißer Dampf austreten.
Zeitvorwahl einstellen Mit der Zeitvorwahl können Sie den Beginn eines Spülprogramms um 3, 6 oder 9 Stunden aufschieben. 1. EIN/AUS-Taste drücken. 2. Taste Zeitvorwahl so oft drücken, bis die Anzeige neben der Stundenanzahl aufleuchtet, um welche der Start des Spülprogramms aufgeschoben werden soll, z. B. 6h, wenn das Spülprogramm in 6 Stunden starten soll. 3. Spülprogramm wählen. Die LED-Anzeige des gewählten Spülprogramms und die Anzeige neben der Stundenanzahl leuchten.
Geschirr ausräumen 3 Es ist normal, dass Innentür und Behältergehäuse feucht sind. • Zuerst Unterkorb, dann Oberkorb ausräumen. Dadurch vermeiden Sie, dass Restwasser vom Oberkorb auf Geschirr im Unterkorb tropft. Pflege und Reinigung 1 Keine Möbelpflege- oder aggressive Reinigungsmittel verwenden. • Bedienteile des Geschirrspülers mit einem weichen Lappen und warmem, klarem Wasser reinigen.
5. Flächensieb (3) aus dem Spülraumboden nehmen und auf beiden Seiten gründlich reinigen. 6. Flächensieb wieder einsetzen. 7. Feinsieb in den Mikrofilter einsetzen und zusammenstecken. 8. Siebsystem einsetzen und durch Schwenken des Griffs im Uhrzeigersinn bis zum Anschlag verriegeln. Darauf achten, dass das Flächensieb nicht über den Spülraumboden heraussteht. 1 Ohne Siebe darf auf keinen Fall gespült werden. Reinigung der Sprüharmdüsen 3 Düsen der Sprüharme regelmäßig auf Verstopfung prüfen.
3. Gereinigten Oberkorb-Sprüharm wieder an das Verbindungsstück schräg ansetzen: beide fest zusammendrücken, bis sie spürbar verrasten. Boden-Sprüharm 1. Boden-Sprüharm zur Entnahme aus seiner Verrastung nach oben ziehen. 2. Sprüharmdüsen reinigen. 3. Boden-Sprüharm wieder an Verbindungsstück ansetzen und fest nach unten drücken, bis er spürbar einrastet.
Was tun, wenn... Kleine Störungen selbst beheben Falls während des Betriebs auf der Bedienblende Anzeigen blinken oder leuchten, die in der nachfolgenden Tabelle beschrieben sind, sehen Sie bitte dort nach, um den Fehler zu beheben. Nach Behebung des Fehlers der im 1er oder 2er Rhythmus blinkenden Programmende-Anzeige, Taste des angefangenen Spülprogramms drücken. Das Spülprogramm läuft weiter. Bei anderen Fehlermeldungen: – Spülprogramm abbrechen. – Gerät aus- und wieder einschalten. – Spülprogramm wählen.
Störung Die Anzeige für Spülprogrammende blinkt im Rhythmus 3 kurz aufeinanderfolgender Lichtsignale. Mögliche Ursache Wasserhahn schließen Das Wasserschutzsystem hat und Kundendienst verangesprochen. ständigen. Netzstecker ist nicht eingesteckt. Programm startet nicht. Pfeifendes Geräusch beim Spülen. Netzstecker einstecken. Sicherung der HausinstallaSicherung ersetzen. tion ist nicht in Ordnung. Bei Geschirrspülermodellen mit Startzeitvorwahl: Eine Startzeit ist vorgewählt.
Wenn das Spülergebnis nicht zufriedenstellend ist Das Geschirr wird nicht sauber. • Es wurde nicht das richtige Spülprogramm gewählt. • Geschirr war so eingeordnet, dass das Spülwasser nicht alle Teile erreicht hat. Die Geschirrkörbe dürfen nicht überladen sein. • Siebe im Spülraumboden sind nicht sauber oder falsch eingesetzt. • Es wurde kein Marken-Reinigungsmittel verwendet oder zu wenig dosiert.
Entsorgung 2 2 1 Verpackungsmaterial Die Verpackungsmaterialien sind umweltverträglich und wiederverwertbar. Die Kunststoffteile sind gekennzeichnet, z. B. >PE<, >PS< etc. Entsorgen Sie die Verpackungsmaterialien entsprechend ihrer Kennzeichnung bei den kommunalen Entsorgungsstellen in den dafür vorgesehenen Sammelbehältern.
Technische Daten Fassungsvermögen: 12 Maßgedecke einschließlich Servicegeschirr Zulässiger Wasserdruck: 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Elektrischer Anschluß: 230 V, 10 A, siehe auch Typschild am rechten Innenrand der Geschirrspülertür. Gesamtleistung 2250 W Integrierbare und Unterbau-Geschirrspüler 5 30 Abmessungen: 820 - 880 x 596 x 570 (H x B x T in mm) max. Gewicht: 50 Kg Dieses Gerät entspricht den folgenden EG-Richtlinien: – 73/23/EWG vom 19.02.
Hinweise für Prüfinstitute Die Prüfung nach EN 60704 muß bei voller Beladung mit dem Testprogramm (siehe Programmtabelle) durchgeführt werden. Die Prüfungen nach EN 50242 müssen mit vollem Salzbehälter des Wasserenthärters, mit vollem Vorratsbehälter für Klarspüler und mit dem Testprogramm (siehe Programmtabelle) durchgeführt werden. Volle Beladung: Halbvolle Beladung: 12 Maßgedecke 6 Maßgedecke einschl. Servicegeeinschl. Servicegeschirr schirr, jeden 2.
Unterkorb mit Besteckkorb*) Besteckkorb *) Eventuell auf der linken Seite vorhandene Tassenauflagen sowie eventuell vorhandene Bierglashalter einschließlich des Gestänges entfernen.
Aufstell- und Anschlussanweisung 1 Sicherheitshinweise für die Installation • Den Geschirrspüler nur stehend transportieren, sonst kann Salzwasser auslaufen. • Vor Inbetriebnahme den Geschirrspüler auf Transportschäden überprüfen. Ein beschädigtes Gerät auf keinen Fall anschließen. Wenden Sie sich im Schadensfall an Ihren Lieferanten.
Aufstellen des Geschirrspülers • Geschirrspüler muss standsicher und waagrecht in alle Richtungen ausgerichtet auf festem Boden aufgestellt werden. • Um Bodenunebenheiten auszugleichen und Gerätehöhe an andere Möbel anzugleichen, Schraubfüße mit einem Schraubendreher herausschrauben. • Die hinteren Gerätefüße sind mit einem Akkuschrauber vorne am Gerät einzustellen (siehe Montageanweisung).
Unterbau-Geschirrspüler (siehe beiliegende Montageanleitung) Dekorplatten zur optischen Anpassung an die Küchenfront: • müssen vom Küchenhersteller bezogen werden • erfordern einen Dekorrahmen • sollten mit doppelseitigem Klebeband auf der Gerätetür fixiert werden (um durchwölben und verziehen zu vermeiden) • Dekorplattenmaße: Höhe 590 mm, Breite 581 mm, Klemmdicke: max.
Anschließen des Geschirrspülers Wasseranschluss • Der Geschirrspüler kann an Kaltwasser und an Warmwasser bis max. 60 °C angeschlossen werden. • Der Geschirrspüler darf nicht an offene Warmwassergeräte und Durchlauferhitzer angeschlossen werden. Zulässiger Wasserdruck Niedrigster zulässiger Wasserdruck: 1 bar (=10 N/cm2 =100 kPa) Unter 1 bar Wasserdruck ziehen Sie bitte Ihren Installateur zu Rate.
Wasserablauf 1 Ablaufschlauch Der Ablaufschlauch darf nicht geknickt, gequetscht oder in sich verschlungen sein. Anschluss des Ablaufschlauches: – maximal zulässige Höhe: 1 Meter. – minimal erforderliche Höhe: 40 cm über der Geräteunterkante. Verlängerungsschläuche • Verlängerungsschläuche sind über den Fachhandel oder unseren Kundendienst zu beziehen. Der Innendurchmesser der Verlängerungsschläuche muss 19 mm betragen, damit die Gerätefunktion nicht gestört wird.
Elektrischer Anschluss Angaben über Netzspannung, Stromart und die erforderliche Absicherung sind dem Typschild zu entnehmen. Das Typschild ist am rechten Innenrand der Geschirrspülertür angebracht. Um den Geschirrspüler vom Netz zu trennen, Netzstecker ziehen. Achtung: – Der Stecker muss nach Aufstellung des Gerätes zugänglich bleiben. – Nach dem Einbau dürfen spannungsführende Teile und betriebsisolierte Leitungen mit dem Prüffinger nach DIN EN 60335-1 nicht berührbar sein.
Garantiebedingungen/Kundendienststellen Deutschland Der Endabnehmer dieses Gerätes (Verbraucher) hat bei einem Kauf dieses Gerätes von einem Unternehmer (Händler) in Deutschland im Rahmen der Vorschriften über den Verbrauchsgüterkauf gesetzliche Rechte, die durch diese Garantie nicht eingeschränkt werden. Diese Garantie räumt dem Verbraucher also zusätzliche Rechte ein.
Österreich Sehr geehrter Kunde! Wir, die Electrolux Hausgeräte GmbH, beglückwünschen Sie zum Erwerb eines Gerätes aus dem Electrolux Konzern. Für dieses Gerät räumen wir Ihnen, als Verbraucher im Sinne des Konsumentenschutzgesetzes gemäß den nachstehenden Bedingungen, eine besondere Garantie ein, die Ihnen zusätzliche Rechte gewährt. 1. Die Garantie beginnt mit dem Tag an dem das Gerät gekauft wurde und erstreckt sich über einen Zeitraum von 24 Monaten.
Österreich Unsere Kundendienststellen und Servicepartner Electrolux stellt Ihnen hiermit jene Partner vor, die dafür garantieren, dass wir Ihnen Top-Qualität mit unseren Kundendiensteinrichtungen jetzt und in Zukunft bieten. Unsere Kundendienststellen in den Bundesländern sind spezialisiert auf unsere Marken: AEG, Electrolux, Juno, Zanussi. Zentrale: Kundendienst Wien, Niederösterreich, nördliches Burgenland Electrolux Hausgeräte GmbH 1230 Wien, Herziggasse 9 Tel. Reparaturannahme 01/86640-330 Tel.
Ersatzteile, Zubehör und Pflegemittel Für Oesterreich: Sie können Ersatzteile, Zubehör und Pflegemittel online bestellen bei http://www.aeg-hausgeraete.
Service Wenn Sie einmal unsere Hilfe benötigen, erreichen Sie uns in Deutschland wie folgt: Bei Fragen zu Bedienung oder Ausstattung Ihres Gerätes Wenden Sie sich an den AEG-Direct Info Service: Telefon: 0180 555 4 555 (0,12 Euro/Min)** Internet: www.aeg-electrolux.de E-Mail: aeg-hausgeraete.kundenservice@aeg-hausgeraete.de Bei technischen Störungen Prüfen Sie bitte zunächst, ob Sie mit Hilfe der Gebrauchsanweisung (Kapitel „Was tun, wenn...“) das Problem selbst beheben können.
From the Electrolux GroupK=qÜÉ=ïçêäÇ…ë=kçKN=ÅÜçáÅÉK aáÉ=bäÉÅíêçäìñJdêìééÉ=áëí=ÇÉê=ïÉäíïÉáí=Öê∏≈íÉ=eÉêëíÉääÉê=îçå=Ö~ëJ=ìåÇ=ëíêçãÄÉíêáÉÄÉåÉå=dÉê®íÉå=ÑΩê=ÇáÉ=hΩÅÜÉI òìã= oÉáåáÖÉå= ìåÇ= ÑΩê= cçêëí= ìåÇ= d~êíÉåK= gÉÇÉë= g~Üê= îÉêâ~ìÑí= ÇáÉ= bäÉÅíêçäìñJdêìééÉ= áå= ΩÄÉê= NRM= i®åÇÉêå= ÇÉê bêÇÉ= ΩÄÉê= RR= jáääáçåÉå= mêçÇìâíÉ= EhΩÜäëÅÜê®åâÉI= eÉêÇÉI= t~ëÅÜã~ëÅÜáåÉåI= pí~ìÄë~ìÖÉêI= jçíçêë®ÖÉå= ìåÇ o~ëÉåã®ÜÉêF=ãáí=ÉáåÉã=tÉêí=îçå=êìåÇ=NQ=jêÇK=rpaK AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.