Benutzerinformation Geschirrspüler VA6011AF
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch. Beachten Sie vor allem die Sicherheitshinweise auf den ersten Seiten dieser Benutzerinformation! Bewahren Sie bitte die Benutzerinformation zum späteren Nachschlagen auf. Geben Sie sie an eventuelle Nachbesitzer des Gerätes weiter.
Inhalt INHALT Gebrauchsanweisung ...................................... 5 Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Wirtschaftlich und umweltbewußt spülen . . . . . . . . . . . . . . . . . . . . . . . . 7 Geräteansicht und Bedienblende . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bedienblende . . .
Inhalt Pflege und Reinigung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Reinigung der Siebe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Was tun, wenn... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...Fehlermeldungen angezeigt werden. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...es Probleme beim Betrieb des Geschirrspülers gibt. . . . . . . . . . . . . . . . .
Gebrauchsanweisung GEBRAUCHSANWEISUNG 1 Sicherheitshinweise Die Sicherheit von ATAG-Elektrogeräten entspricht den anerkannten Regeln der Technik und dem Gerätesicherheitsgesetz. Dennoch sehen wir uns als Hersteller veranlaßt, Sie mit folgenden Sicherheitshinweisen vertraut zu machen: Aufstellung, Anschluß, Inbetriebnahme • Der Geschirrspüler darf nur stehend transportiert werden. • Überprüfen Sie den Geschirrspüler auf Transportschäden. Ein beschädigtes Gerät auf keinen Fall anschließen.
Gebrauchsanweisung Allgemeine Sicherheit • Reparaturen am Geschirrspüler dürfen nur von Fachkräften durchgeführt werden. Durch unsachgemäße Reparaturen können erhebliche Gefahren für den Benutzer entstehen. Wenden Sie sich im Reparaturfall an unseren Kundendienst oder an Ihren Fachhändler. • Geschirrspüler nie in Betrieb nehmen, wenn Netzkabel, Zu- /Ablaufschlauch beschädigt sind oder Bedienblende, Arbeitsplatte oder der Sockelbereich so beschädigt sind, daß das Gerät offen zugänglich ist.
Gebrauchsanweisung • Im Fehlerfall zuerst Wasserhahn schließen, dann das Gerät ausschalten und Netzstecker aus der Steckdose ziehen. Bei Festanschluß: Sicherung(en) ausschalten bzw. Schraubsicherungen herausdrehen. 2 Entsorgung Verpackungsmaterial entsorgen Entsorgen Sie das Verpackungsmaterial des Geschirrspülautomaten sachgerecht. Alle verwendeten Verpackungsmaterialien sind umweltverträglich und wiederverwertbar.
Gebrauchsanweisung Geräteansicht und Bedienblende Oberer Sprüharm Gummidichtung für Ankopplung des Wasserzulaufs zum Sprüharm Sprüharme Härtebereichsschalter Vorratsbehälter für Spezialsalz Behälter für Reinigungsmittel Vorratsbehälter für Klarspüler 8 Typschild Siebe
Gebrauchsanweisung Bedienblende Funktions-Tasten Türgriff Startzeit einstellen Kontrollanzeigen 1 2 3 4 EIN/AUS-Taste Bedienfeld Multidisplay Das Bedienfeld besteht aus der EIN/AUS-Taste und den Programmtasten mit LED-Anzeigen.
Gebrauchsanweisung Vor der ersten Inbetriebnahme Entfernen Sie vor Inbetriebnahme alle Klammern, mit denen die Geschirrkörbe für den Transport gesichert werden. Führen Sie dann folgende Schritte durch: 1. Wasserenthärter einstellen 2. Spezialsalz für Wasserenthärter einfüllen 3. Klarspüler einfüllen Wasserenthärter Um Kalkablagerungen auf Geschirr und im Geschirrspüler zu verhindern, muss das Geschirr mit weichem, d.h. kalkarmen Wasser gespült werden.
Gebrauchsanweisung Wasserenthärter einstellen 0 Wasserenthärter gemäß Tabelle auf die Wasserhärte Ihres Wohngebietes einstellen: Geschirrspülautomat muss ausgeschaltet sein. Mechanische Einstellung: 1. Tür des Geschirrspülers öffnen. 2. Unteren Geschirrkorb aus dem Geschirrspüler herausnehmen. 3. Härtebereichsschalter auf O oder 1 drehen (siehe Tabelle). 4. Unteren Geschirrkorb wieder einsetzen. Elektronische Einstellung: 1. EIN/AUS-Taste drücken. Die LED der EIN/AUS-Taste leuchtet.
Gebrauchsanweisung Spezialsalz für Wasserenthärter 3 Ist die Wasserhärte in Ihrem Wohngebiet unter 4 °d, dann muß das Wasser in Ihrem Geschirrspüler nicht enthärtet werden und Sie benötigen kein Spezialsalz oder Salzersatzstoffe. Sie haben 2 Möglichkeiten, das Wasser zu enthärten: • Wenn Sie Reinigungsmittel verwenden, welches bereits Salzersatzstoffe enthält, wird nur dieses Reinigungsmittel in den Behälter für Reinigungsmittel gegeben.
Gebrauchsanweisung 3 Wenn für die Verwendung von Reinigungsmittel inkl. Spezialsalz der Wasserenthärter elektronisch auf „1“ eingestellt wird, dann wird damit die Kontroll-Anzeige für Spezialsalz abgeschaltet. Spezialsalz einfüllen Wenn Sie Reinigungsmittel und Spezialsalz getrennt verwenden, füllen Sie Spezialsalz ein: – Vor der ersten Inbetriebnahme des Geschirrspülers. – Wenn auf der Bedienblende die Kontrollanzeige für Spezialsalz J leuchtet. 0 1. Tür öffnen, Unterkorb herausnehmen. 2.
Gebrauchsanweisung Klarspüler Durch den Klarspüler erhält man fleckenfreies, glänzendes Geschirr und klare Gläser. Sie haben 2 Möglichkeiten, Klarspüler zuzuführen: • Wenn Sie Reinigungsmittel verwenden, welches den Klarspüler bereits enthält, wird das Reinigungsmittel inkl. Klarspüler in den Behälter für Reinigungsmittel gegeben. – In diesem Fall muss die Klarspülerzugabe aus dem Vorratsbehälter ausgeschaltet sein, um Doppeldosierung zu vermeiden.
Gebrauchsanweisung Das Multidisplay zeigt die momentane Einstellung an: 0d Klarspülerzulauf ausgeschaltet 1d Klarspülerzulauf eingeschaltet (Voreinstellung ab Werk) 4. Drücken der Funktions-Taste 2 schaltet die Klarspülerzugabe ein bzw. aus.. 5. Zeigt das Multidisplay die gewünschte Einstellung an, EIN/AUS-Taste drücken. Die Einstellung ist dann gespeichert.
Gebrauchsanweisung 4. Klarspüler genau bis zur gestrichelten Markierung „max“ einfüllen; das entspricht einer Füllmenge von ca. 140 ml 5. Deckel zurückklappen und zudrücken, bis dieser einrastet. 6. Wenn Klarspüler danebengelaufen ist, mit einem Lappen wegwischen. Sonst bildet sich beim Spülen zuviel Schaum. Klarspülerdosierung einstellen Beim Geschirrspülen wird aus dem Vorratsfach Klarspüler ins Spülwasser abgegeben. Die Dosierung können Sie von 1-6 einstellen.
Gebrauchsanweisung Im täglichen Gebrauch • Muß Spezialsalz oder Klarspüler nachgefüllt werden ? • Besteck und Geschirr in Geschirrspüler einordnen • Reinigungsmittel für Geschirrspüler einfüllen • Für Besteck und Geschirr geeignetes Spülprogramm auswählen • Spülprogramm starten Besteck und Geschirr einordnen 1 Schwämme, Haushaltstücher und alle Gegenstände, die sich mit Wasser vollsaugen können, dürfen nicht im Geschirrspüler gereinigt werden.
Gebrauchsanweisung – kleine Gegenstände (z. B. Deckel) in den Besteckkorb legen Besteck einordnen 1 0 Vorsicht: Lange, spitze Besteckteile stellen im Besteckkorb, besonders für Kinder eine Gefahrenquelle dar (siehe Sicherheitshinweise)! Sie müssen daher in den Oberkorb gelegt werden. Ihr Gerät ist zusätzlich zum unteren Besteckkorb mit einer Besteckablage im Oberkorb ausgestattet. Messer, kleine Löffel und kleine Gabeln in die Besteckablage einordnen.
Gebrauchsanweisung Bei einigen Geschirrspülermodellen ist es möglich, den Besteckkorb aufzuklappen. Damit der Besteckkorb beim Herausnehmen nicht aufklappen kann, sollten Sie den zweiteiligen Griff mit der Hand immer ganz umfassen. 0 1. Besteckkorb auf Tisch oder Arbeitsplatte stellen. 2. Beide Griffteile auseinanderklappen. 3. Besteck herausnehmen. 4. Beide Griffteile zusammenklappen.
Gebrauchsanweisung Variante 2: Die rechten Tellereinsätze des Unterkorbs sind nach links klappbar Um größeres Geschirr leichter einordnen zu können, sind die beiden rechten Tellereinsätze des Unterkorbs nach links klappbar: 0 1. Rechte Tellereinsätze hinten leicht anheben. 3 2. Tellereinsätze nach links umklappen.
Gebrauchsanweisung Variante 4: Beide hintere Tellereinsätze des Unterkorbs sind überkreuz klappbar 3 Um größeres Geschirr leichter einordnen zu können, sind die beiden hinteren Tellereinsätze des Unterkorbs überkreuz klappbar. Tassen, Gläser und Kaffeeservice einordnen Kleineres, empfindliches Geschirr und lange, spitze Besteckteile im Oberkorb einordnen. • Geschirrteile auf und unter den klappbaren Tassenauflagen versetzt anordnen, damit das Spülwasser alle Geschirrteile erreicht.
Gebrauchsanweisung Oberkorb in der Höhe verstellen Maximale Höhe des Geschirrs im Oberkorb Unterkorb 3 bei angehobenem Oberkorb 22 cm 31 cm bei abgesenktem Oberkorb 24 cm 29 cm Die Höhenverstellung ist auch bei beladenen Körben möglich. Absenken des Oberkorbs 1. Oberkorb ganz herausziehen. 2. Oberkorb am Griff bis zum Anschlag anheben und senkrecht absenken. Der Oberkorb rastet in der unteren Position ein. Anheben des Oberkorbs 1. Oberkorb ganz herausziehen. 2.
Gebrauchsanweisung Dosierung der Reinigungsmittel 1 Verwenden Sie ausschließlich Reinigungsmittel für Geschirrspüler. Dosierung der Reinigungsmittel: – Vor Beginn des Programms (nicht während des Programms Vorspülen). Reinigungsmittel wird während Ablauf des Programms automatisch eingespült. Beachten Sie die Hinweise auf der Verpackung des Reinigungsmittels, beispielweise zur Dosierung und Aufbewahrung. Das Fach für Reinigungsmittel befindet sich innen an der Tür. 0 1.
Gebrauchsanweisung Die Verwendung von kombinierten Reinigungstabletten. Wichtige Hinweise Es gibt auch Reinigungstabletten, die die Funktionen von Geschirrspülmittel, Klarspüler und Salz kombinieren. 0 1. Falls Sie diese Art von Geschirrspülmittel verwenden, müssen Sie zuerst prüfen, ob die Härte des Leitungswassers mit den Hinweisen auf der Verpackung übereinstimmt und/oder ob das Mittel für den Gebrauch geeignet ist. 2.
Gebrauchsanweisung Konzentrierte Geschirrspülmittel Spülmittel für Geschirrspüler werden nach ihrer chemischen Zusammensetzung in zwei Gruppen unterteilt: – traditionelle alkalische Geschirrspülmittel mit ätzenden Bestandteilen – leicht alkalische konzentrierte Geschirrspülmittel mit natürlichen Enzymen 2 Die Verwendung von Spülprogrammen mit einer Temperatur von 50 °C und konzentrierten Geschirrspülmitteln ist umweltfreundlich und verlängert die Lebensdauer des Geschirrs, da die 50 °C-Programme speziell
Gebrauchsanweisung Spülprogramme mit Automatik Bei den AUTOMATIK-Programmen wird über die Trübung des Spülwassers festgestellt, wie stark das Geschirr verschmutzt ist. Bei geringer Beladung und leichter Verschmutzung des Geschirrs dauern die Programmteile „Vorspülen“ , „Reinigen“ und „Zwischenspülen“ kürzer und der Wasserverbrauch ist geringer.
Gebrauchsanweisung Spülprogramm auswählen (Programmtabelle) Wählen Sie mit Hilfe dieser Tabelle das geeignete Spülprogramm aus: 1) Geschirrart zusätzlich Eß- und Kochgeschirr - Art der Ver- • stark verschmutzt schmutzung • stark verschmutzt • angetrocknete Speisereste, besonders Eiweiß und Stärke Geeignetes Spülprogramm: ò ò Kaffee- und Dessertgeschirr - • normal verschmutzt • angetrocknete Speisereste ò mit empfindlichen Gläsern • normal verschmutzt besonders besonders geeignet geeignet bei Ve
Gebrauchsanweisung Spülprogramm starten 0 1. Überprüfen Sie, ob Geschirr und Besteck im Geschirrspüler so eingeord- net sind, dass die Sprüharme sich frei drehen können. 2. Wasserhahn ganz aufdrehen. 3. Tür schließen. 4. EIN/AUS-Taste drücken. Die Anzeige der EIN/AUS-Taste leuchtet. 5. Programmtaste für das gewünschte Programm drücken (siehe „Programmtabelle“). Die Programmanzeige leuchtet. Im Multidisplay wird die zu erwartende Restlaufzeit für das Programm angezeigt.
Gebrauchsanweisung Spülprogramm unterbrechen durch Öffnen der Geschirrspülertür Beim Öffnen der Tür kann heißer Dampf austreten. Verbrühungsgefahr! Tür vorsichtig öffnen. 0 1. Geschirrspülertür öffnen. Das Spülprogramm stoppt. 2. Tür schließen. Das Spülprogramm läuft weiter. 1 Spülprogramm abbrechen (RESET) 0 1. Funktions-Tasten 1 und 2 drücken und gedrückt halten. Die Programmanzeige des laufenden Spülprogramms blinkt einige Sekunden und erlischt dann. 2. Funktions-Tasten loslassen.
Gebrauchsanweisung Startzeitvorwahl löschen: Solange das Spülprogramm nicht begonnen hat, können Sie die Startzeitvorwahl löschen. Drücken Sie die Taste Zeitvorwahl so oft, bis im Multidisplay die Laufzeit des gewählten Programms erscheint. Das gewählte Spülprogramm beginnt sofort. Spülprogramm wechseln nach Startzeitvorwahl: Solange das Spülprogramm nicht begonnen hat, können Sie durch Drücken einer Programmtaste das Spülprogramm noch wechseln. 0 1.
Gebrauchsanweisung Geschirrspüler ausschalten Geschirrspüler erst ausschalten, wenn das Multidisplay „0“ als Restlaufzeit des Spülprogramms anzeigt. 0 1. EIN/AUS-Taste drücken. Anzeige der EIN/AUS-Taste erlischt. Beim Öffnen der Tür, unmittelbar nach Programmende, kann heißer Dampf austreten. Deshalb: 2. Tür vorsichtig öffnen. 1 Geschirr ausräumen 3 • Heißes Geschirr ist stoßempfindlich. Geschirr deshalb vor dem Ausräumen abkühlen lassen.
Gebrauchsanweisung Reinigung der Siebe Die Siebe im Spülraumboden sind in hohem Grade selbstreinigend. Trotzdem sollten diese gelegentlich kontrolliert und gereinigt werden. Verschmutzte Siebe beeinträchtigen das Spülergebnis. 0 1. Tür öffnen, Unterkorb herausnehmen. 2. Das Siebsystem des Geschirrspülers besteht aus Grob-/Feinsieb, Mikrofilter und Flächensieb. Mit Griff des Mikrofilters das Siebsystem entriegeln und entnehmen. 3.
Gebrauchsanweisung Was tun, wenn... Versuchen Sie mit Hilfe der hier aufgeführten Hinweise kleinere Störungen am Geschirrspüler selbst zu beheben. Wenn Sie bei einer der hier aufgeführten Störungen oder zur Behebung eines Bedienfehlers den Kundendienst in Anspruch nehmen, erfolgt der Besuch des Kundendienst-Technikers auch während der Garantiezeit nicht kostenlos. ...Fehlermeldungen angezeigt werden.
Gebrauchsanweisung Nach Behebung des Fehlers Å 10 oder Å 20 die Taste des angefangenen Spülprogramms drücken. Das Spülprogramm läuft weiter. Wird der Fehler erneut angezeigt, verständigen Sie bitte den Kundendienst. 3 Bei allen anderen angezeigten Fehlern bitte den Kundendienst verständigen und die Fehleranzeige nennen. (Siehe Kapitel Kundendienst) ...es Probleme beim Betrieb des Geschirrspülers gibt. Störung Programm startet nicht.
Gebrauchsanweisung – Es wurde kein Marken-Reinigungsmittel verwendet oder zu wenig dosiert. – Bei Kalkbelägen auf dem Geschirr: Vorratsbehälter für das Spezialsalz ist leer oder die Wasserenthärtungsanlage ist falsch eingestellt. – Ablaufschlauch ist nicht korrekt verlegt. Das Geschirr wird nicht trocken und bleibt ohne Glanz. – Es wurde kein Marken-Klarspüler verwendet. – Vorratsbehälter für den Klarspüler ist leer.
Gebrauchsanweisung Technische Daten Fassungsvermögen: 12 Maßgedecke einschließlich Servicegeschirr Zulässiger Wasserdruck: 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Elektrischer Anschluß: Angaben über den elektrischen Anschluß stehen auf dem Typschild am rechten Innenrand der Geschirrspülertür. Geschirrspüler: Standgeräte Abmessungen: 850 x 600 x 600 (H x B x T in mm) max. Gewicht: 54 Kg Integrierbare und Unterbau-Geschirrspüler Abmessungen: 820 - 880 x 596 x 570 (H x B x T in mm) max.
Gebrauchsanweisung Hinweise für Prüfinstitute Die Prüfung nach EN 60704 muß bei voller Beladung mit dem Testprogramm (siehe Programmtabelle) durchgeführt werden. Die Prüfungen nach EN 50242 müssen mit vollem Salzbehälter des Wasserenthärters, mit vollem Vorratsbehälter für Klarspüler und mit dem Testprogramm (siehe Programmtabelle) durchgeführt werden. Reinigerdosierung : Volle Beladung: 12 Maßgedecke einschl. Servicegeschirr Halbvolle Beladung: 6 Maßgedecke einschl.
Aufstell- und Anschlußanweisung AUFSTELLSTELL- UND ANSCHLUßANWEISUNG Aufstellen des Geschirrspülers • Geschirrspüler muß standsicher und waagrecht ausgerichtet auf festem Boden aufgestellt werden. • Um Bodenunebenheiten auszugleichen und Gerätehöhe an andere Möbel anzugleichen, Schraubfüße herausschrauben: – mit einem Schraubendreher. • Bei Unterbau-, integrierbaren und vollintegrierbaren Geschirrspülern sind die hinteren Gerätefüße mit einem Schraubendreher vorne am Gerät einzustellen.
Aufstell- und Anschlußanweisung Integrierbarer Geschirrspüler (siehe beiliegende Montageschablone) 3 Die Gerätetür kann mit einer Küchenmöbeltür folgender Abmessungen verkleidet werden: Breite: 591 – 594 mm Dicke: 16 – 24 mm Höhe: abhängig von (variabel) – Nischenhöhe – Sockelhöhe – Anpassung an Fugenverlauf benachbarter Möbel Das genaue Höhenmaß muß am Aufstellort von den benachbarten Möbeln abgemessen werden. Gewicht: max.
Aufstell- und Anschlußanweisung Anschließen des Geschirrspülers Wasseranschluß Der Geschirrspüler hat Sicherheitseinrichtungen, die den Rückfluß von Spülwasser in das Trinkwasser-Leitungsnetz verhindern und den geltenden wassertechnischen Sicherheitsvorschriften entsprechen. • Der Geschirrspüler kann an Kaltwasser und an Warmwasser bis max. 60 °C angeschlossen werden. • Der Geschirrspüler darf nicht an offene Warmwassergeräte und Durchlauferhitzer angeschlossen werden.
Aufstell- und Anschlußanweisung 3 Das folgende Kapitel gilt nur für Geschirrspüler, die an der Schlauchverschraubung zum Wasserhahn ein Sicherheitsventil haben: Zulaufschlauch mit Sicherheitsventil Nach Anschluß des doppelwandigen Zulaufschlauchs befindet sich das Sicherheitsventil direkt am Wasserhahn. Daher steht der Zulaufschlauch nur während des Wasserzulaufs unter Druck.
Aufstell- und Anschlußanweisung Wasserablauf Ablaufschlauch 1 Der Ablaufschlauch darf nicht geknickt, gequetscht oder in sich verschlungen sein. • Anschluß des Ablaufschlauches: – maximal zulässige Höhe: 0,85 Meter. – minimal erforderliche Höhe 40cm über der Geräteunterkante. Verlängerungsschläuche • Verlängerungsschläuche sind über den Fachhandel oder unseren Kundendienst zu beziehen. Der Innendurchmesser der Verlängerungsschläuche muß 19 mm betragen, damit die Gerätefunktion nicht gestört wird.
Aufstell- und Anschlußanweisung Wasserschutzsystem Zum Schutz gegen Wasserschäden ist der Geschirrspüler mit einem Wasserschutzsystem ausgestattet. Im Fehlerfall unterbricht das Sicherheitsventil im Zulaufschlauch sofort den Wasserzulauf und die Entleerungspumpe schaltet sich ein. Damit kann Wasser weder aus- noch überlaufen. Im Gerät befindliches Restwasser wird automatisch abgepumpt. 1 Das Wasserschutzsystem funktioniert auch, wenn das Gerät ausgeschaltet ist.
Aufstell- und Anschlußanweisung Anschlußtechnik Zulauf- und Ablaufschläuche sowie das Netzkabel müssen seitlich vom Geschirrspüler angeschlossen werden, da hinter dem Gerät kein Platz dafür ist. Das nachfolgende Beispiel einer Sanitär- und Elektroinstallation kann nur eine Empfehlung sein, da maßgebend die Gegebenheiten am Aufstellort sind (vorhandene Anschlüsse, örtliche Anschlußvorschriften der Energie- bzw. der Wasserwerke, usw...).
Service SERVICE Im Kapitel „Was tun, wenn...“ sind die wichtigsten Fehlerquellen zusammengestellt, die Sie selbst beheben können. Wenn Sie trotzdem für einen der aufgeführten Hinweise oder aufgrund von Fehlbedienung den Kundendienst in Anspruch nehmen, so erfolgt der Besuch des Kundendienst-Technikers auch während der Garantiezeit nicht kostenlos. Wenn Sie für eine Störung keinen Hinweis in dieser Gebrauchsanweisung finden, wenden Sie sich bitte an den Kundendienst.
822 960 259 - 00 - 0203