ÖKO_FAVORIT 50750 i Dishwasher User Instructions
Dear customer, Please read these user instructions carefully. Please observe the safety instructions on the first few pages of these user instructions! Please keep these user instructions for later reference. Pass them on to any subsequent owner of the appliance. 1 0 The warning triangle and/or specific words (Warning!, Caution!, Important!) are used to highlight instructions that are important for your safety or for the function of the appliance. It is imperative that these instructions are observed.
Contents CONTENTS Operating Instructions .................................... 5 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Economical and Ecological Dishwashing . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Appliance Features and Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 4 Installation and Connection Instructions . . . . . . . . . . . . . . . . 30 Installing the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dishwashers That Can Be Integrated . . . . . . . . . . . . . . . . . . . . . . . . . . . . Built-In Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Free-Standing Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions OPERATING INSTRUCTIONS 1 Safety Instructions The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law. Nevertheless, as a manufacturer we consider it our obligation to make you aware of the following safety information: Installation, Connection and Placing into Operation • The dishwasher may only be transported upright. • Check the dishwasher for transport damage.
Operating Instructions • Never place the dishwasher in operation if the mains cable, water inlet or drain hose is damaged; or the control panel, work top or plinth area is damaged such that the inside of the appliance is freely accessible. • If the mains lead is damaged, or is to be replaced for a longer lead, the cable (obtainable from AEG Service Force) must be replaced by a service engineer authorised by AEG. • Never unplug the appliance by pulling on the cable, always pull the plug.
Operating Instructions • In the event of a fault, first close the tap, then switch off the appliance and unplug it from the mains. If the appliance is permanently wired to the mains: remove the fuse. 2 Disposal Disposing of the Packaging Material Dispose of the dishwasher packaging material correctly. All the packaging materials used are harmless to the environment and can be recycled. • Plastic parts are marked with standard international abbreviations: – >PE< for polyethylene, e.g.
Operating Instructions Appliance Features and Control Panel Top Spray Nozzle Rubber Seal for Connecting the Water Feed to the Upper Spray Arm Spray Arms Container for Salt Container for Rinse Aid Detergent Dispenser Rating Filters Plate 8
Operating Instructions Control panel Function Softener Button Button Door Handle Set Start Delay Indicators Multi-Display Control Field The Control Field comprises the ON/OFF switch and the programme buttons with LED indicators. Softener and Function Button: in addition to the wash programme marked, it is also possible to adjust the dishwasher's water softener using the combination of these buttons. The Multi-Display can display, – the hardness setting to which the water softener is set.
Operating Instructions Adjust the Water Softener To avoid the scale deposits on the dishes and in the dishwasher, the dishes must be washed with soft, i.e. low lime content, water. The dishwasher therefore has a built-in water softener, in which tap water from a hardness of 4 °d (German degree) is softened with the aid of special salt. 3 0 You water supplier will be able to inform you on the hardness and hardness range of the water in your area.
Operating Instructions 6. When the hardness setting is correct, press the ON/OFF switch. The hardness setting is then saved. Filling with Salt for the Water Softener 1 Use only special salt for dishwashers. Never fill the salt container with any another type of salt (e.g. culinary salt) or dishwasher detergent, as this would irreparably damage the water softener. Prior to filling with salt, please check each time that you really do have a packet of dishwasher salt in your hand.
Operating Instructions Depending on the size of the salt grains, it can take several hours for the salt to dissolve in the water and for the SALT indicator to extinguish. The setting of the water softener and thus the consumption of salt are dependent on the hardness of the local water. 3 Filling with Rinse Aid Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, spot and streak free drying. 1 Only use rinse aid specifically designed for domestic dishwashers.
Operating Instructions 4. Fill with rinse aid exactly up to the level marked “max”; this corresponds to a quantity of approx. 140 ml. 5. Close the lid and press until it locks into place. 6. Wipe up any spilt rinse aid with a cloth. Otherwise too much foam will be formed during the wash. Adjusting Rinse Aid Dosing 3 As the dishes are washed rinse aid is released from the dispenser into the wash water. The dose is factory set at 4, and can be adjusted from 1 to 6.
Operating Instructions Loading Cutlery and Dishes 1 Sponges, household cloths and any object that can absorb water should not be washed in the dishwasher.
Operating Instructions Loading Cutlery 1 Long bladed knives stored in an upright position are a potential hazard. 1 Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Take care when loading or unloading sharp items such as knives. To ensure that all items of cutlery are completely washed, you should 0 1. Place the grid insert on the cutlery rack 2. Place short knives, forks and spoons in the grid insert with their handles pointing downwards.
Operating Instructions Loading Pans, Frying Pans and Large Plates Load large and heavily soiled dishes in the lower rack. To ease the loading of large items at some dishwasher-models the two rows of prongs for the right-hand plate insert can be folded down: 0 1. Slightly lift the right plate insert. 3 2. Fold the plate insert to the left.
Operating Instructions Loading Cups, Glasses and Coffee Services Load small, delicate items and long pointed cutlery in the upper rack. • Arrange items of crockery on the folding cups racks so that they are offset from each other and water can reach all items. • The cup racks can be folded up out of the way for tall items. • Lay or hang wine, champagne, and brandy glasses in the cut outs on the cup racks. • Glasses, beakers, etc. can also be placed on the two rows of prongs on the left of the upper rack.
Operating Instructions Adjusting the Height of the Upper Basket Maximum Height of the Dishes in the Upper Basket Lower Basket 3 With upper basket raised 22 cm 31 cm With upper basket lowered 24 cm 29 cm The height of the basket can also be adjusted when it is loaded. Depending on the model, your appliance is provided with one of the following types of upper basket: Lowering the Upper Basket: 0 1. Pull the upper basket out completely. 2. Lift the upper basket at the rear right and lower.
Operating Instructions Filling with Detergent 1 Only use dishwasher detergent. Fill with detergent: – Prior to the start of a wash programme (not for the pre wash programme). The detergent is released into the wash water during the programme. Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging. The detergent compartment is on the inside of the dishwasher door. 0 1. If the lid is closed: press release button (1). The lid springs open. 2 2.
Operating Instructions Bio Wash Programmes and Concentrated Detergents Based on their chemical composition, dishwasher detergents can be split into two basic types: – Conventional, alkaline detergents with caustic components – Weak alkaline concentrated detergents with natural enzymes.
Operating Instructions Selecting the Wash Programme (Programme Table) Choose the most suitable wash programme with the aid of this table: Type of Dishes In Addition - Type of Soiling Suitable Programme: Programme Sequence 2) Consumption Figures: 3) Dessert Dishes and Coffee Service All Dish Types with non-temperature resistant dishes with delicate glasses - • normally soiled • lightly soiled Dinner Service and Cooking Utensils - • heavily • normally soiled soiled • dried on left- • dried lefto
Operating Instructions Start the Wash Programme 0 1. Check that when the dishes and cutlery are loaded into the dishwasher the spray arms are free to rotate. 2. Open the tap fully. 3. Shut the door. 4. Press the ON/OFF button. The ON/OFF button indicator illuminates. 5. Press the programme button for the desired programme (see "Programme Table"). The programme indicator illuminates. The selected programme begins after around 6 seconds.
Operating Instructions 0 1. Open the door of the dishwasher. The wash programme stops. 2. The indicator for the programme that is currently running extinguishes. 3. Close the door. The wash programme continues. Cancelling the wash programme 0 1. Press the button for the current wash programme and hold it pressed. The programme indicator for the current wash programme flashes for a few seconds and then extinguishes. 2. Release the programme button, the wash programme is cancelled.
Operating Instructions Switching Off the Dishwasher Switch the dishwasher off when the multi-display indicates "0" for the remaining programme time. 0 1. Press the ON/OFF button. The ON/OFF button indicator extinguishes. Hot steam may escape from the appliance when opening the door immediately after the end of the programme. 2. Open the door carefully, as steam may escape.
Operating Instructions Cleaning the Filter The filters should be checked and cleaned regularly. Blocked filters will give poor wash results. 0 1. Open the door, remove the lower rack. 2. The dishwasher filter system comprises a coarse/fine filter, microfilter and a flat filter. Unlock the filter system using the handle on the microfilter, and remove. 3. Turn the handle about ¼ a turn anticlockwise and remove. 4.
Operating Instructions What to do, if ... Try to rectify minor faults on the dishwasher with the aid of the instructions given here. If you call an engineer to resolve a of fault listed here, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is in guarantee. ...Error messages • If the programme indicator for the selected wash programme is flashing and fault code (1 or (2 is displayed on the multi-display, you can probably rectify the fault yourself.
Operating Instructions ...there are problems with the operation of the dishwasher. Symptom Possible Cause Solution The door of the dishwasher is Shut the door. not closed properly. Mains plug is not plugged in. Insert mains plug. The programme does not start. House fuse is defective. Replace fuse. A start delay is selected. If the dishes are to be washed immediately, set the start delay to 0 hours The washing compartment is made from rust-free stainless steel.
Operating Instructions There are streaks, milky spots or a bluish coating on glasses and dishes. – Lower rinse aid dosing. There are dried water drops on the glasses and dishes. – Increase rinse aid dosing. – The detergent may be the cause. Contact the detergent manufacturer’s customer advisor. Technical Data Capacity: 12 place settings including serving dishes Permitted Water Pressure: 1-10 bar (=10-100 N/cm2 = 0.1-1.
Operating Instructions Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme (see Programme Table). Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see Programme Table). Full Load: 12 place settings incl. serving dishes Half Load: 6 place settings incl.
Installation and Connection Instructions INSTALLATION AND CONNECTION INSTRUCTIONS Installing the Dishwasher • The dishwasher must be installed on a firm floor and adjusted such that it is stable and level. • To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units extend the threaded feet by unscrewing: – use a screwdriver.
Installation and Connection Instructions • Depending on type, the dishwasher is to be installed as follows: Dishwashers That Can Be Integrated (see installation template supplied) 3 The door of the appliance can be fitted with a wooden/facing panel with the following dimensions: Width 587mm 591 – 594 mm Thickness: 16 – 24 mm Height: dependent on (variable) – Aperture height – Plinth height – The adjustment so that the unit matches the height of the adjoining units The exact height of the adjoining
Installation and Connection Instructions • If the dishwasher is installed underneath a kitchen work surface, the original work surface of the dishwasher is to be removed as follows: – Unscrew the screws (1) from the elbows on the back side. – Slide the work surface approx. 1cm to the rear (2) , lift at the front (3) and remove. – Press the work surface retaining brackets at the position shown in the diagram (4) and remove the bracket at an angle to the rear (5).
Installation and Connection Instructions Connecting the Dishwasher Water Connection The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations. • The dishwasher can be connected to cold and hot water supplies up to max. 60 °C. • The dishwasher must not be connected to open hot water appliances or instantaneous water heaters.
Installation and Connection Instructions Water drain Drain hose 1 The drain hose must not be kinked, crushed or entangled. • Connecting the drain hose: – Maximum permitted height: 1 metre. – Minimum required height 30 cm above the lower edge of the machine. Extension hoses • Extension hoses are available from AEG Service Force. The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded.
Installation and Connection Instructions Leak Prevention System For protection from damage due to water leaks, the dishwasher is equipped with a leak prevention system, the AQUA CONTROL SYSTEM. In the event of a fault, the safety valve immediately interrupts the supply of water to the appliance and the drain pump switches on. By this means water can neither escape nor overflow. The remaining water in the appliance is automatically pumped out.
Installation and Connection Instructions Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. 1 WARNING - This appliance must be earthed. The manufacturer declines any responsibility should these safety measures not be observed. Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. To isolate the dishwasher from the mains, remove the mains plug.
Installation and Connection Instructions Connections The water inlet and drain hoses, as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the appliance. The plumbing and electrical installation example given below can only be regarded as a recommendation.
Guarantee Conditions GUARANTEE CONDITIONS 1. 2. 3. 4. 5. 6. Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials.
Service & Spare parts SERVICE & SPARE PARTS If you wish to purchase spare parts or require an engineer, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your telephone call will be automatically routed to the Service Centre covering your post code area. When you contact the Service Centre they will need the following information: 1. Your name & address, including post code. 2. Your telephone number 3. Clear and concise details of the fault. 4.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.