FAV55BVI1P NL FR USER MANUAL Gebruiksaanwijzing Afwasautomaat Notice d'utilisation Lave-vaisselle 2 26
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE......................................................................................... 3 2. VEILIGHEIDSVOORSCHRIFTEN.................................................................................4 3. BESCHRIJVING VAN HET PRODUCT........................................................................6 4. BEDIENINGSPANEEL................................................................................................. 7 5. PROGRAMMA’S..................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • • Als de voedingskabel beschadigd is, moet de fabrikant, een erkende serviceverlener of een gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt.
NEDERLANDS • Trek niet aan het netsnoer om het apparaat los te koppelen. Trek altijd aan de stekker. • Dit apparaat voldoet aan de EEGrichtlijnen. • Alleen voor VK en Ierland. Het apparaat heeft een stekker van 13 ampère. Als de zekering van de stekker verwisseld moet worden, gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Beschadig de waterslangen niet.
www.aeg.com • Verwijder de deurgreep om te voorkomen dat kinderen en huisdieren opgesloten raken in het apparaat. 3. BESCHRIJVING VAN HET PRODUCT 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Top sproeiarm Bovenste sproeiarm Onderste sproeiarm Filters Typeplaatje Zoutreservoir Luchtopening 3.1 TimeBeam De TimeBeam is een weergave die op de vloer onder de deur van het apparaat te zien is. • Wanneer het programma start, verschijnt de duur van het programma.
NEDERLANDS Als AirDry tijdens de droogfase wordt geactiveerd, is de projectie op de vloer mogelijk niet volledig zichtbaar. Raadpleeg het display van het bedieningspaneel om de resttijd van het lopende programma te controleren. 4. BEDIENINGSPANEEL 1 1 2 3 4 5 Aan/uit-toets Weergave Delay-toets Program-toets Sanitize-toets 2 3 6 7 8 9 4 5 6 7 8 9 TimeSaver-toets XtraDry-toets Reset-toets Indicatielampjes 4.1 Indicatielampjes Aanduiding Beschrijving Einde-indicatielampje.
www.aeg.
NEDERLANDS Water (l) Energie (kWh) Bereidingsduur (min) P3 12.5-14.5 1.4-1.7 170-190 P5 12 - 14 0.7 - 0.9 82-92 P4 10 0.9 30 P6 9 - 10 1.1 - 1.3 230 - 250 Programma 1) 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.
www.aeg.com De waterontharder moet worden afgesteld op de hardheid van het water in uw woonplaats. Uw waterleidingbedrijf kan u informeren over de hardheid van het water in uw woonplaats. Het is belangrijk om het correcte niveau voor de waterontharder in te stellen voor goede wasresultaten. Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.
NEDERLANDS (hoogste hoeveelheid). Niveau 0 schakelt het glansmiddeldoseerbakje uit en er wordt geen glansmiddel afgegeven. Fabrieksinstelling: stand 4. Het apparaat moet in de programmakeuzemodus staan. Het apparaat moet in de programmakeuzemodus staan. 1. Houd om de gebruikersmodus in te 1. Houd om de gebruikersmodus in te en ingedrukt tot de indicatielampjes , , , , en gaan knipperen en het display blanco is. 2.
www.aeg.com Het geluidssignaal voor het einde van het programma inschakelen • Op het display verschijnt een getal en de letter C. Elk nummer hoort bij een andere kleur. – Het apparaat moet in de programmakeuzemodus staan. 1. Houd om de gebruikersmodus in te voeren tegelijkertijd en ingedrukt tot de indicatielampjes , , , , en gaan knipperen en het display blanco is. en , , om de kleur 3. Druk herhaaldelijk op te wijzigen. • De verschillende kleuren worden op de keukenvloer weergegeven. 4.
NEDERLANDS • Het display toont de huidige , , , en gaan knipperen en het display blanco is. 2. Druk op en instelling: = AirDry ingeschakeld. . • De indicatielampjes , , , gaan uit. • Het indicatielampje knipperen. 13 blijft 3. Druk op om de instelling te = AirDry wijzigen: uitgeschakeld. 4. Druk op de knop aan/uit om de instelling te bevestigen. 7. OPTIES De gewenste opties moeten elke keer dat u een programma start worden geactiveerd.
www.aeg.com de laatste spoelfase gedurende minstens 10 minuten op 70°C te houden. Sanitize activeren Druk op , het bijbehorende indicatielampje gaat nu branden. Als de optie niet van toepassing is op het programma, dan gaat het bijbehorende indicatielampje niet branden of het knippert even en gaat dan uit. Het display geeft de bijgewerkte programmaduur weer. 8. VOORDAT U HET APPARAAT VOOR DE EERSTE KEER GEBRUIKT 1.
NEDERLANDS 8.2 Het vullen van het glansmiddeldoseerbakje A B 15 3. Verwijder gemorst glansmiddel met een absorberend doekje om te voorkomen dat er te veel schuim ontstaat. 4. Sluit het deksel. Zorg ervoor dat de deksel op zijn plaats dichtklikt. Vul het glansmiddeldoseerbakje bij wanneer de indicatie (A) helder wordt. Als u multitabletten gebruikt en het droogresultaat is naar tevredenheid, kan de indicatie voor het glansmiddel worden uitgeschakeld.
www.aeg.com 2. Doe de vaatwastablet of het poeder in het doseerbakje (B). 3. Plaats een kleine hoeveelheid van het vaatwasmiddel in de binnenkant van de deur van het apparaat als het programma een voorwasfase heeft. 4. Sluit het deksel. Zorg ervoor dat de deksel op zijn plaats dichtklikt. 9.2 Een programma instellen en starten De Auto Off-functie Deze functie verlaagt het energieverbruik door het apparaat automatisch uit te schakelen als het niet werkt.
NEDERLANDS Einde van het programma 17 Draai de waterkraan dicht. Wanneer het programma is voltooid en u opent de deur, wordt het apparaat automatisch uitgeschakeld. 10. AANWIJZINGEN EN TIPS 10.1 Algemeen De volgende tips zorgen voor optimale schoonmaak- en droogresultaten en helpen ook het milieu te beschermen. • Verwijder grotere etensresten van de borden en gooi ze in de vuilnisbak. • Spoel de vaat niet eerst af.
www.aeg.com • • • • • • • absorberen (sponzen, keukenhanddoeken). Verwijder grotere etensresten van de borden en gooi ze in de vuilnisbak. Maak aangebrande voedselresten op de voorwerpen zachter. Plaats holle voorwerpen (bijv. kopjes, glazen en pannen) met de opening naar beneden. Zorg er voor dat glazen andere glazen niet aanraken. Doe bestek en kleine items in het bestekmandje. Leg lichte voorwerpen in het bovenrek. Zorg ervoor dat de voorwerpen niet verschuiven.
NEDERLANDS 19 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3. Verwijder de platte filter (A). 4. Was de filters. LET OP! Een onjuiste plaatsing van de filters kan leiden tot slechte wasresultaten en het apparaat beschadigen. 11.2 De bovenste sproeiarm schoonmaken 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6.
www.aeg.com 11.3 Buitenkant reinigen • Maak het apparaat schoon met een vochtige, zachte doek. • Gebruik alleen neutrale schoonmaakmiddelen. • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen. 11.4 De binnenkant van de machine reinigen 3. Reinig de sproeiarm onder stromend water. Gebruik een smal en puntig gereedschap, bijv. een tandenstoker, om de vuildeeltjes uit de gaten te verwijderen.
NEDERLANDS WAARSCHUWING! Niet juist uitgevoerde reparaties kunnen de veiligheid van de gebruiker ernstig in gevaar brengen. Alle reparaties moeten worden uitgevoerd door bevoegd personeel. 21 Bij sommige problemen wordt er op de display een alarmcode weergegeven. Het merendeel van de problemen die ontstaan kunnen worden opgelost zonder contact op te nemen met een erkend servicecentrum. Probleem en alarmcode Mogelijke oorzaak en oplossing U kunt het apparaat niet activeren.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing De resterende duur in het display wordt verlengd en schakelt bijna naar het eind van de programmaduur. • Dit is geen storing. Het apparaat werkt goed. Kleine lekkage uit de deur van het apparaat. • Het apparaat staat niet waterpas. Draai aan de verstelbare pootjes (indien van toepassing). • De deur van het apparaat is niet gecentreerd op de kuip. Verstel de achterpoot (indien van toepassing). De deur van het apparaat sluit moeilijk.
NEDERLANDS 23 Probleem Mogelijke oorzaak en oplossing Slechte droogresultaten. • Serviesgoed heeft te lang in het gesloten apparaat gestaan. • Het glansmiddel is op of de dosering van glansmiddel is niet voldoende. Stel de dosering van het glansmiddel in op een hogere stand. • Plastic voorwerpen moeten mogelijk met een doek worden afgedroogd. • Activeer voor de beste droogprestatie de optie XtraDry en stel AirDry in. • We raden aan altijd glansmiddel te gebruiken, zelfs in combinatie met wastabletten.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Er bevinden zich aan het einde • De vaatwastablet raakte klem in het vaatwasmiddeldovan het programma resten van seerbakje en is daardoor niet volledig weggespoeld vaatwasmiddel in het vaatwasdoor het water. middeldoseerbakje. • Het water kan het vaatwasmiddel niet uit het vaatwasmiddeldoseerbakje spoelen. Zorg ervoor dat de bovenste sproeiarm niet geblokkeerd of verstopt is.
NEDERLANDS Energieverbruik Modus aan laten (W) 5.0 Energieverbruik Uit-modus (W) 0.10 25 1) Zie het typeplaatje voor andere waarden. 2) Als het hete water door een alternatieve, milieuvriendelijkere energiebron geproduceerd wordt (bijv. zonnepanelen en windenergie), gebruik dan een heetwatervoorziening om het energieverbruik te verminderen. 14. MILIEUBESCHERMING Recycle de materialen met het symbool . Gooi de verpakking in een geschikte verzamelcontainer om het te recyclen.
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................27 2. CONSIGNES DE SÉCURITÉ......................................................................................28 3. DESCRIPTION DE L'APPAREIL.................................................................................30 4. BANDEAU DE COMMANDE....................................................................................31 5. PROGRAMMES....................
FRANÇAIS 1. 27 INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximal de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant d'installer des tuyaux neufs, des tuyaux n'ayant pas servi depuis longtemps, lorsqu'une réparation a été effectuée ou qu'un nouveau dispositif a été installé (compteurs d'eau, etc.), laissez l'eau s'écouler jusqu'à ce qu'elle soit parfaitement propre et claire.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Bras d'aspersion supérieur Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 3.1 TimeBeam Le faisceau TimeBeam est une lumière projetée sur le sol, sous la porte de l'appareil. • Lorsque le programme démarre, la durée du programme s'affiche. • Lorsque le programme est terminé, 0:00 et CLEAN s'affichent.
FRANÇAIS Durant la phase de séchage, lorsque l'option AirDry est activée, il est possible que la projection sur le sol ne soit pas totalement visible. Pour vérifier le temps restant au programme en cours, vous pouvez regarder l'affichage du bandeau de commande. 4. BANDEAU DE COMMANDE 2 1 1 2 3 4 5 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche Sanitize 3 6 7 8 9 4 5 6 7 8 9 Touche TimeSaver Touche XtraDry Touche Reset Voyants 4.
www.aeg.
FRANÇAIS Eau (l) Consommation électrique (kWh) Durée (min) P3 12.5-14.5 1.4-1.7 170-190 P5 12 - 14 0.7 - 0.9 82-92 P4 10 0.9 30 P6 9 - 10 1.1 - 1.3 230 - 250 Programme 1) 33 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.com L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région. Il est important de régler l'adoucisseur d'eau sur un niveau adéquat pour vous garantir de bons résultats de lavage. Dureté eau Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Niveau de l'adoucisseur d'eau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.
FRANÇAIS 35 Vous pouvez définir la quantité de liquide de rinçage libérée entre le niveau 1 (quantité minimale) et le niveau 6 (quantité maximale). Le dosage 0 désactive le distributeur de liquide de rinçage et le liquide de rinçage n'est pas diffusé. rinçage et que vous êtes satisfait des résultats du séchage, vous pouvez désactiver la notification de remplissage du liquide de rinçage.
www.aeg.com Comment activer le signal sonore de fin de programme L'appareil doit être en mode Programmation. – 1. Pour entrer en mode utilisateur, maintenez les touches et enfoncées simultanément jusqu'à ce , que les voyants , , , et se mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants , , • Un chiffre et la lettre Cs'affichent. Chaque chiffre est associé à une couleur différente. , et s'éteignent. = TimeBeam désactivé. à plusieurs 3.
FRANÇAIS enfoncées simultanément jusqu'à ce que les voyants , , , , et se mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants s'éteignent. • Le voyant clignoter. . , , , et 37 • L'affichage indique le réglage actuel : = AirDry activé. 3. Appuyez sur la touche pour = AirDry modifier le réglage : désactivé. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. continue à 7.
www.aeg.com ne s'allume pas ou clignote rapidement pendant quelques secondes, puis s'éteint. L'affichage indique la durée du programme réactualisée. 7.3 Sanitize Cette option garantit de meilleurs résultats d'hygiène en maintenant la température à 70 °C pendant au moins 10 minutes au cours de la dernière phase de rinçage. Comment activer l'option Sanitize Appuyez sur ; le voyant correspondant s'allume.
FRANÇAIS ATTENTION! De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Après avoir rempli le réservoir de sel régénérant, lancez imédiatement un programme pour éviter la corrosion. 1. Ouvrez le couvercle (C). 2. Remplissez le distributeur (B) jusqu'à ce que le liquide de rinçage atteigne le repère « MAX ». 3. Si le liquide de rinçage déborde, épongez-le avec un chiffon absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle.
www.aeg.com 9.1 Utilisation du produit de lavage A B C ATTENTION! Utilisez uniquement un produit de lavage spécial pour lave-vaisselle. 1. Appuyez sur la touche de déverrouillage (A) pour ouvrir le couvercle (C). 2. Versez le produit de lavage sous forme de poudre ou tablette dans le compartiment approprié (B). 3. Si le programme comporte une phase de prélavage, versez une petite quantité de produit de lavage à l'intérieur de la porte de l'appareil. 4. Fermez le couvercle.
FRANÇAIS Si la porte reste ouverte pendant plus de 30 secondes pendant la phase de séchage, le programme en cours d'exécution se termine. Cela ne se produit pas si la porte est ouverte par AirDry. ATTENTION! Ne pas essayer de fermer la porte de l'appareil moins de 2 minutes après l'ouverture automatique par AirDry, car cela peut causer des dommages à l'appareil. Si, par la suite, la porte est fermée pendant 3 minutes supplémentaires, le programme en cours d'exécution se termine.
www.aeg.com 10.2 Utilisation de sel régénérant, de liquide de rinçage et de produit de lavage • Utilisez uniquement du sel régénérant, du liquide de rinçage et du produit de lavage conçus pour les lave-vaisselle. D'autres produits peuvent endommager l'appareil.
FRANÇAIS 10.6 Déchargement des paniers 43 2. Commencez par décharger le panier inférieur, puis le panier supérieur. À la fin du programme, il peut rester de l'eau sur les parois et la porte de l'appareil. 1. Attendez que la vaisselle refroidisse avant de la retirer de l'appareil. La vaisselle encore chaude est sensible aux chocs. 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur.
www.aeg.com 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 3. Nettoyez le bras d'aspersion à l'eau courante. Utilisez un outil pointu comme un cure-dent pour extraire toutes les particules de saleté incrustées dans les orifices. 4.
FRANÇAIS • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur • Nettoyez soigneusement l'appareil, y compris le joint en caoutchouc de la porte, avec un chiffon doux humide. • Si vous utilisez régulièrement des programmes de courte durée, des dépôts de graisse et des dépôts calcaires peuvent se former à 45 l'intérieur de l'appareil. Pour éviter cela, nous recommandons de lancer un programme long au moins 2 fois par mois.
www.aeg.com Problème et code d'alarme Cause et solution possibles L'appareil ne se remplit pas d'eau. L'affichage indique . L'appareil ne vidange pas l'eau. L'affichage indique . Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Assurez-vous que le robinet d'eau est ouvert. • Assurez-vous que la pression de l'arrivée d'eau n'est pas trop basse. Pour obtenir cette information, contactez votre compagnie des eaux. • Assurez-vous que le robinet d'eau n'est pas obstrué.
FRANÇAIS 47 Problème et code d'alarme Cause et solution possibles L'appareil déclenche le disjoncteur. • L'ampérage n'est pas suffisant pour alimenter tous les appareils en cours de fonctionnement simultanément. Vérifiez l'ampérage de la prise et la capacité du mètre, ou éteignez l'un des appareils qui sont en cours de fonctionnement. • Défaut électrique interne de l'appareil. Faites appel à un service après vente agréé.
www.aeg.com Problème Cause et solution possibles Il y a des taches et traces de gouttes d'eau séchées sur les verres et la vaisselle. • La quantité de liquide de rinçage libérée n'est pas suffisante. Placez le sélecteur de dosage du liquide de rinçage sur le niveau le plus élevé. • Il se peut que la qualité du liquide de rinçage soit en cause. La vaisselle est mouillée. • Pour de meilleurs performances de séchage, activez l'option XtraDry et réglez AirDry.
FRANÇAIS Problème 49 Cause et solution possibles Dépôts calcaires sur la vaissel- • Le niveau de sel régénérant est bas, vérifiez le voyant le, dans la cuve et à l'intérieur de remplissage. de la porte. • Le bouchon du réservoir de sel régénérant est dévissé. • Votre eau est dure. Reportez-vous au chapitre « Adoucisseur d'eau ». • Même si vous employez des pastilles tout en 1, utilisez du sel régénérant et procédez à une régénération de l'adoucisseur d'eau.
www.aeg.com Consommation électrique Mode « Éteint » (W) 0.10 1) Reportez-vous à la plaque signalétique pour les autres valeurs. 2) Si l'eau chaude est produite à partir de sources d'énergie respectueuses de l'environnement (par exemple, panneaux solaires ou énergie éolienne), utilisez une arrivée d'eau chaude afin de réduire la consommation d'énergie. 14. EN MATIÈRE DE PROTECTION DE L'ENVIRONNEMENT Recyclez les matériaux portant le électroniques. Ne jetez pas les appareils symbole .
FRANÇAIS 51
117886381-A-392016 www.aeg.