FAVORIT 60820 Lave-vaisselle Informations pour les utilisateurs
Chère cliente, cher client, veuillez lire avec soin ces informations pour les utilisateurs. Tenez surtout compte de la section “Sécurité” des premières pages de ces informations pour les utilisateurs! Conservez ces informations aux utilisateurs pour un usage ultérieur. Transmettez-les à un éventuel possesseur ultérieur de la machine.
Sommaire SOMMAIRE Mode d'emploi ............................................. 5 Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Protection de l’environnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Laver la vaisselle de manière économique et ménageant l’environnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Vue de l'appareil et bandeau de commande . . . . . . . . . . . . . . . . .
Sommaire Que faire quand... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...les messages de défaut sont affichés. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...il y a des problèmes lors du fonctionnement du lave-vaisselle. . . . . . . . . ...le résultat de lavage n’est pas satisfaisant. . . . . . . . . . . . . . . . . . . . . . . . . 32 33 34 34 Caractéristiques techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode d'emploi MODE D'EMPLOI 1 Consignes de sécurité La sécurité des appareils électroménagers AEG est conforme aux règles reconnues de la technique et à la législation portant sur la sécurité des appareils. En tant que fabricant, nous attirons cependant votre attention sur les indications supplémentaires suivantes: Installation, raccordement, mise en service • Le lave-vaisselle peut uniquement être transporté debout. • Contrôlez le lave-vaisselle pour dégâts de transport éventuels.
Mode d'emploi • Lors de la mise au rebut du lave-vaisselle: coupez le câble d'alimentation au ras de l'appareil et jetez-le. Neutralisez le dispositif de fermeture de porte, de façon à ce que la porte ne ferme plus. Sécurité générale • Les réparations sur le lave-vaisselle peuvent uniquement être effectuées par du personnel qualifié. Les réparations non effectuées dans les règles peuvent être la source de dangers importants pour l'utilisateur.
Mode d'emploi • Le système de protection contre les fuites d'eau protège de manière fiable contre les dégâts des eaux. Les conditions suivantes doivent cependant être remplies à cet effet: – L'appareil doit également rester raccordé à l'alimentation électrique lorsqu'il n'est pas en service. – Le lave-vaisselle doit être installé correctement. – Fermez toujours le robinet d'arrivée d'eau lorsque le lave-vaisselle n'est pas utilisé pendant une période prolongée, p. ex. durant un voyage de vacances.
Mode d'emploi 2 Laver la vaisselle de manière économique et ménageant l’environnement • Ne raccordez le lave-vaisselle à une alimentation en eau chaude que si vous disposez d’une installation d’eau chaude qui ne chauffe pas à l’électricité. • Réglez correctement l’adoucisseur. • Ne rincez pas préalablement la vaisselle à l’eau courante.
Mode d'emploi Vue de l'appareil et bandeau de commande Bras de lavage supérieur Joint en caoutchouc pour couplage de la tuyauterie d'arrivée d'eau au bras de lavage intermédiaire Bras de lavage Commutateur de plage de dureté Réservoir pour sel régénérant Réservoir de produit de lavage Réservoir pour produit de rinçage Plaque signalétique Filtres 9
Mode d'emploi Bandeau de commande Poignée de la porte Touches de fonction 1 3 2 4 Touches de fonction Zone de commande Départ différé Voyants Fenêtre d’affichage La zone de commande se compose de la touche MARCHE/ARRET M et des touches de programme avec leurs voyants.
Mode d'emploi Les voyants ont la signification suivante: 3 J Remplir le réservoir de sel régénérant H Remplir le réservoir de produit de rinçage ^ Ouvrir le robinet d'eau [ Nettoyer le système de filtration du lave-vaisselle Le voyant [ doit vous rappeler de contrôler à l'occasion les filtres du lave-vaisselle et, si nécessaire, de les nettoyer. Il s'allume à intervalles réguliers, indépendamment de l'état d'encrassement des filtres.
Mode d'emploi Avant la première utilisation Avant la mise en service, retirez les attaches en plastique avec lesquelles les paniers à vaisselle ont été bloqués pendant le transport. Procédez ensuite aux étapes suivantes: 1. Réglez l’adoucisseur 2. Remplissez le réservoir de sel régénérant 3.
Mode d'emploi 1)(°th) degré français, unité de mesure de la dureté de l'eau 2)(mmol/l) millimole par litre, unité de mesure internationale de la dureté de l'eau *réglage d'usine Réglez l'adoucisseur suivant le tableau en fonction de la dureté de l'eau de votre région: 0 1. Le lave-vaisselle doit être mis hors service. 2. Réglage mécanique: Ouvrez la porte du lave-vaisselle. 3. Sortez le panier à vaisselle inférieur du lave-vaisselle. 4. Tournez le commutateur de plage de dureté sur O ou 1. 5.
Mode d'emploi Remplissage du réservoir de sel régénérant 1 Utilisez exclusivement du sel spécial régénérant pour lave-vaisselle. Ne remplissez jamais le réservoir de sel régénérant à l’aide d’autres sortes de sel (p. ex. sel alimentaire) ni de produit de lavage. Ceci pourrait rendre inutilisable l’adoucisseur. Soyez donc vigilant lors du remplissage. Versez le sel régénérant: – Avant la première mise en service du lave-vaisselle – Si le voyant J s’allume sur le bandeau de commande.
Mode d'emploi Produit de rinçage Le produit de rinçage permet d'obtenir une vaisselle éclatante et des verres impeccables. 2 possibilités vous sont offertes pour introduire le produit de rinçage: • Si vous utilisez des produits de lavage contenant déjà un produit de rinçage, le produit de lavage (avec le produit de rinçage intégré) doit être introduit dans le bac destiné au produit de lavage.
Mode d'emploi Remplir le réservoir de produit de rinçage Si vous utilisez séparément un produit de lavage et un produit de rinçage, remplissez le réservoir de ce dernier: – Avant la première mise en service du lave-vaisselle – Lorsque le voyant H est allumé sur le bandeau de commande. Le réservoir de produit de rinçage se trouve sur la face intérieure de la porte du lave-vaisselle. 0 1. Ouvrez la porte. 2. Appuyez sur la touche de déverrouillage du réservoir de produit de rinçage. 3.
Mode d'emploi Régler la dose de produit de rinçage Ce produit évite que l’eau ne reste sur la vaisselle sous forme de gouttelettes laissant des taches blanches après séchage. L’admission du produit de rinçage se fait automatiquement. Vous pouvez régler le dosage de 1 à 6. A la livraison, votre appareil est réglé sur la position 4. Ne modifiez le dosage que si vous constatez de mauvais résultats de rinçage. (voir «Que faire si ...?») 0 1. Ouvrez la porte du lave-vaisselle. 2.
Mode d'emploi Utilisation journalière • Faut-il compléter le sel régénérant ou le produit de rinçage? • Disposez les couverts et la vaisselle dans le lave-vaisselle • Remplissez le réservoir de produit de lavage pour lave-vaisselle • Sélectionnez un programme de lavage convenant aux couverts et à la vaisselle • Lancez le programme de lavage Disposez les couverts et la vaisselle 1 Les éponges, serviettes de ménage et tous les objets susceptibles de se saturer en eau, ne peuvent pas être lavés au lave-vai
Mode d'emploi – les récipients tels que tasses, verres, casseroles, etc., soient disposés avec l’ouverture vers le bas, afin que l’eau puisse s’écouler facilement – la vaisselle et les couverts ne s’enchevêtrent ou ne s’imbriquent pas les uns dans les autres – les verres ne se touchent pas afin d’éviter les bris de verre et la formation des taches de contact qui peuvent se produire au séchage – placer les petits objets (p. ex.
Mode d'emploi Disposer dans le panier à couverts les fourchettes et les cuillères qui n'ont pas place dans le tiroir à couverts . Afin que l'eau de lavage asperge toutes les pièces dans le panier à couverts, vous devriez insérer 0 1. l'élément grille sur le panier à couverts 2. disposer les fourchettes et les cuillères avec le manche vers le bas dans l'élément grille du panier à couverts. 3. Pour les couverts de grande taille tels que p. ex. fouet, on peut enlever une partie de la grille à couverts.
Mode d'emploi Disposer de la vaisselle (casseroles, grandes assiettes) Placez les grandes pièces de vaisselle très sales dans le panier inférieur. Afin de placer plus facilement les récipients les plus grands, il est, sur certains modèles de lave-vaisselle, également possible de rabattre les deux rangées du support à assiettes de droite: 0 1. Soulevez légèrement à l'arrière les supports à assiettes de droite. 3 2. Rabattre les supports à assiettes vers la gauche.
Mode d'emploi Disposition de la vaisselle (tasses, verres, …) Placez les petites pièces de vaisselle, fragiles et les longs couverts dans le panier supérieur. • Disposez les pièces de vaisselle en quinconce sur les supports à tasses amovibles et en dessous de ceux-ci afin que l’eau de lavage atteigne toutes les pièces de vaisselle. • Pour les pièces de vaisselle hautes, rabattez les supports à tasses.
Mode d'emploi Réglage en hauteur du panier supérieur Hauteur maximale de vaisselle dans le panier supérieur le panier inférieur 3 avec le panier supérieur soulevé 22 cm 31 cm avec le panier supérieur abaissé 24 cm 29 cm Le réglage en hauteur est également possible lorsque les paniers sont remplis. Suivant le modèle, l'appareil est équipé d’un panier supérieur différent: Mise en position basse du panier supérieur: 1er type de panier 0 1. Sortez entièrement le panier supérieur. 2.
Mode d'emploi Mise en position basse du panier supérieur: 0 1. Sortez entièrement le panier supérieur. 2. Soulevez le panier supérieur jusqu'à la butée et laissez-le descendre verticalement. Le panier supérieur se verrouille dans la position inférieure. Mise en position haute du panier supérieur: 0 1. Sortez entièrement le panier supérieur. 2. Soulevez le panier supérieur jusqu'à la butée et laissez-le descendre verticalement. Le panier supérieur se verrouille dans la position supérieure.
Mode d'emploi Remplissage du produit de lavage 1 N’utilisez que des produits de lavage pour des lave-vaisselle ménagers. Le produit de lavage est dangereux! – Le réservoir de produit de lavage doit être rempli avant chaque programme de lavage, à l’exception du programme prélavage. Le produit de lavage est libéré automatiquement au cours du programme de lavage. Veuillez respecter les recommandations de dosage et de stockage du fabricant mentionnées sur les emballages des produits de lavage.
Mode d'emploi Produits de lavage compacts Les produits de lavage pour lave-vaisselle peuvent se diviser en deux catégories principales selon leur composition chimique: – les produits de lavage alcalins traditionnels, à base de substances corrosives, – les produits de lavage compacts faiblement alcalins, à base d'enzymes naturelles.
Mode d'emploi Sélectionner le programme de lavage (tableau des programmes) Sélectionnez le programme de lavage approprié à l'aide de ce tableau: 1) Type de vaisselle plus Type de salissures Service de table et plats - Récipients Service à café et à dessert - avec des verres fragiles - • très sale • moyennement • restes séchés sale d'aliments, en particulier • restes séchés blanc d'œuf et d'aliments amidon • utilisation • de moyenne- • légèrement toute ment à légèsale récente, de rement moyennesale
Mode d'emploi Comment faire un lavage 0 1. Vérifiez que la vaisselle et les couverts sont disposés dans le lave-vais- selle de telle façon que les bras d’aspersion puissent tourner librement. 2. Ouvrez entièrement le robinet d’arrivée d’eau. 3. Refermez la porte. 4. Appuyez sur la touche MARCHE/ARRET. Le voyant MARCHE/ARRET s’allume. 5. Appuyez sur la touche correspondant au programme souhaité (voir «Tableau des programmes»). Le voyant correspondant s’allume.
Mode d'emploi Interrompre le programme de lavage en ouvrant la porte du lave-vaisselle Lors de l’ouverture de la porte, de la vapeur brûlante peut sortir de l’appareil. Ouvrez la porte avec précaution. 0 1. Ouvrez la porte du lave-vaisselle. Le programme de lavage s’arrête. 2. Le voyant correspondant au programme de lavage en cours s’éteint. 3. Fermez la porte. Le programme de lavage se poursuit. 1 Arrêter le programme de lavage 0 1. Appuyez sur la touche du programme en cours et maintenez-la enfoncée.
Mode d'emploi Reconnaissance de charge – Sensorlogic Lorsqu’un programme de lavage démarre bien que le panier supérieur et/ou le panier inférieur ne soient que partiellement chargés, la haute technologie électronique équipant cet appareil adapte la quantité d’eau de lavage ainsi que la durée du programme de lavage à la quantité de vaisselle. De la sorte, il est possible de laver également une petite quantité de vaisselle rapidement et économiquement.
Mode d'emploi Entretien et nettoyage yage 1 Nettoyez régulièrement les surfaces extérieures de l’appareil et le bandeau de commande avec un chiffon doux humide et si nécessaire, uniquement avec des détergents doux. N’employez jamais de produits abrasifs ou de solvants (acétone, trichloréthylène, etc …). Nettoyez les joints d’étanchéité de la porte et les distributeurs de produit de lavage et de rinçage avec un chiffon humide. Nettoyage du filtre Les filtres sont situés au fond de la cuve.
Mode d'emploi 7. Replacez le filtre plat en vérifiant que les bords du filtre s’applique correctement sur le fond de la cuve. 8. Placez le filtre mixte grossier/fin dans le microfiltre et assemblez-les. 9. Remettez l’ensemble de ces 3 filtres et verrouillez le tout en basculant le levier dans le sens des aiguilles d’une montre jusqu’à la butée. 1 Ne faites jamais fonctionner l’appareil sans les filtres. Que faire quand...
Mode d'emploi ...les messages de défaut sont affichés. • Si l'affichage multiple affiche le code d'erreur (2 ou si l'indication ^ est allumée, vous pouvez éventuellement remédier vous-même à l'anomalie. Après correction du défaut (2 et du défaut avec l'indication ^, enfoncer la touche du programme de lavage entamé. Le programme de lavage se poursuit. Si le code d'erreur s'affiche à nouveau, avertissez le service après-vente.
Mode d'emploi ...il y a des problèmes lors du fonctionnement du lavevaisselle. Symptômes Cause possible La porte du lave-vaisselle n’est pas correctement fermée. Solutions Refermez la porte. L’appareil n’est pas correcteBranchez la prise. ment branché. Le programme ne démarre pas. Le fusible de l’installation électrique de la maison n’est Remplacez le fusible pas en bon état. Un départ différé a été programmé (selon modèle). Des taches de rouille sont visibles à l’intérieur de la cuve.
Mode d'emploi – Le produit de lavage n’est pas correctement dosé ou ne convient pas au lavage en lave-vaisselle. – En cas de dépôts de calcaire sur la vaisselle: le réservoir de sel régénérant est vide ou l’adoucisseur est mal réglé. – Le tuyau d’écoulement n’est pas placé correctement. La vaisselle ne sèche pas ou ne brille pas. – La vaisselle est restée trop longtemps dans l’appareil. – Le réservoir pour le liquide de rinçage est vide.
Mode d'emploi Caractéristiques techniques Capacité: 12 couverts normalisés y compris vaisselle de service Pression d’eau autorisée: 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Raccordement électrique: Les informations concernant le raccordement électrique se trouvent sur la plaque signalétique placée sur le côté droit de la porte du lave-vaisselle. Lave-vaisselle: «pose-libres» Dimensions: 850 x 600 x 600 (H x L x P en mm) poids max.
Mode d'emploi Indications à l'attention des instituts d'essai L'essai selon la norme EN 60704 doit être effectué à pleine charge avec le programme de test (voir tableau des programmes). Les essais selon la norme EN 50242 doivent être effectués avec le bac à sel de l'adoucisseur d'eau plein, avec le bac d'alimentation du produit de rinçage plein et avec le programme de test (voir tableau des programmes).
Mode d'emploi Panier inférieur avec panier à couverts 38 Panier à couverts
Instructions de montage et de raccordement INSTRUCTIONS DE MONTAGE GE ET DE RACCORDEMENT Installation du lave-vaisselle • Le lave-vaisselle doit bien reposer sur le sol et être mis à niveau sur un sol bien stable.
Instructions de montage et de raccordement • Si le lave-vaisselle doit être installé en dessous d'un plan de travail de cuisine, vous devez enlever le plan de travail d'origine du lave-vaisselle comme suit: – Dévissez les vis (1) des pièces en équerre à la paroi arrière. – Faites glisser le plan de travail de l'appareil d'environ 1 cm vers l'arrière (2), soulevez-le à l'avant (3) et retirez-le.
Instructions de montage et de raccordement Raccordement du lave-vaisselle Arrivée d'eau Le lave-vaisselle possède des dispositifs de sécurité qui empêchent le reflux de l'eau de lavage dans le réseau de distribution d'eau potable et sont conformes aux prescriptions de sécurité en vigueur en matière de sécurité hydraulique. • Le lave-vaisselle peut être alimenté en eau froide et en eau chaude jusqu'à 60 °C max. • Le lave-vaisselle ne peut pas être raccordé à un chauffe-eau.
Instructions de montage et de raccordement Evacuation de l’eau Tuyau d’évacuation Le tuyau d’évacuation ne peut être ni plié, ni écrasé ni replié sur lui-même. • Raccordement du tuyau d’évacuation: – hauteur maximum: 1 mètre. – hauteur minimum nécessaire, 30 cm. Tuyaux de prolongement • Les tuyaux de prolongement sont disponibles chez votre magasin vendeur. Le diamètre intérieur des flexibles de prolongement doit être de 19 mm.
Instructions de montage et de raccordement Système de protection contre les inondations A titre de protection contre les dégâts des eaux, le lave-vaisselle est équipé d’un système de protection contre les inondations, le SYSTEME AQUA CONTROL. En cas d’anomalie, la soupape de sécurité interrompt immédiatement l’arrivée d’eau et la pompe d’évacuation se met en marche. De cette manière, l’eau ne peut ni s’écouler ni déborder.
Instructions de montage et de raccordement Technique de raccordement Les tuyaux d’alimentation en eau et d’évacuation ainsi que le câble d’alimentation électrique se raccordent sur le côté du lave-vaisselle, aucune place n’étant disponible à cet effet à l’arrière de l’appareil.
Adresses du service après-vente ADRESSES DU SERVICE APRÈS-VENTE Electrolux Home Products Belgium Consumer services ELECTROLUX SERVICE Bergensesteenweg, 719 1502 Lembeek Province de Liège: S.D.E. Rue Gaucet, 26 4020 Liège Téléphone Téléfax 02/363.04.44 02/363.04.00 02/363.04.60 04/343.11.60 04/343.47.68 CONDITIONS DE GARANTIE DÉCLARATION DE CONDITIONS DE GARANTIE. Nos appareils sont produits avec le plus grand soin. Malgré cela, un défaut peut toujours se présenter.
Conditions de garantie 6. Il ne peut pas être fait appel à la garantie pour des anomalies bénignes qui n'affectent pas la valeur et la solidité générales de l'appareil. 7. L'obligation de garantie perd ses effets lorsque les défectuosités sont causées par : • une réaction chimique ou électrochimique provoquée par l'eau, • des conditions environnementales anormales en général, • des conditions de fonctionnement inadaptées, • un contact avec des produits agressifs. 8.
Service SERVICE au chapitre «Que faire si...» sont rassemblées les sources de panne les plus fréquentes, auxquelles vous pouvez remédier vous-même. Si vous faites malgré tout appel au service après-vente pour un des problèmes mentionnés ou suite à une erreur de manipulation, la visite du technicien de service après-vente ne sera pas gratuite pendant la période de garantie non plus. Si vous ne trouvez pas d’indication pour une panne dans ce mode d’emploi, veuillez vous adresser au service après-vente.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.