FAVORIT 64060 VI Der vollintegrierbare Geschirrspülautomat Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch. Beachten Sie vor allem die Sicherheitshinweise auf den ersten Seiten dieser Benutzerinformation! Bewahren Sie bitte die Benutzerinformation zum späteren Nachschlagen auf. Geben Sie sie an eventuelle Nachbesitzer des Gerätes weiter.
Inhalt INHALT Gebrauchsanweisung ...................................... 5 Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Wirtschaftlich und umweltbewußt spülen . . . . . . . . . . . . . . . . . . . . . . . . 7 Geräteansicht, Bedien- und Anzeigefeld . . . . . . . . . . . . . . . . . . . . . . . . . Bedien- und Anzeigefeld .
Inhalt Pflege und Reinigung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Reinigung der Siebe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Was tun, wenn... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...Fehlermeldungen angezeigt werden. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...es Probleme beim Betrieb des Geschirrspülers gibt. . . . . . . . . . . . . . . . .
Gebrauchsanweisung GEBRAUCHSANWEISUNG 1 Sicherheitshinweise Die Sicherheit von AEG-Elektrogeräten entspricht den anerkannten Regeln der Technik und dem Gerätesicherheitsgesetz. Dennoch sehen wir uns als Hersteller veranlaßt, Sie mit folgenden Sicherheitshinweisen vertraut zu machen: Aufstellung, Anschluß, Inbetriebnahme • Der Geschirrspüler darf nur stehend transportiert werden. • Überprüfen Sie den Geschirrspüler auf Transportschäden. Ein beschädigtes Gerät auf keinen Fall anschließen.
Gebrauchsanweisung Allgemeine Sicherheit • Reparaturen am Geschirrspüler dürfen nur von Fachkräften durchgeführt werden. Durch unsachgemäße Reparaturen können erhebliche Gefahren für den Benutzer entstehen. Wenden Sie sich im Reparaturfall an unseren Kundendienst oder an Ihren Fachhändler. • Geschirrspüler nie in Betrieb nehmen, wenn Netzkabel, Zu- /Ablaufschlauch beschädigt sind oder Bedienblende, Arbeitsplatte oder der Sockelbereich so beschädigt sind, daß das Gerät offen zugänglich ist.
Gebrauchsanweisung • Im Fehlerfall zuerst Wasserhahn schließen, dann das Gerät ausschalten und Netzstecker aus der Steckdose ziehen. Bei Festanschluß: Sicherung(en) ausschalten bzw. Schraubsicherungen herausdrehen. 2 Entsorgung Verpackungsmaterial entsorgen Entsorgen Sie das Verpackungsmaterial des Geschirrspülautomaten sachgerecht. Alle verwendeten Verpackungsmaterialien sind umweltverträglich und wiederverwertbar.
Gebrauchsanweisung Geräteansicht, Bedien- und Anzeigefeld Deckendusche Gummidichtung für Ankopplung des Wasserzulaufs zum Sprüharm Sprüharme Härtebereichsschalter Vorratsbehälter für Spezialsalz Vorratsbehälter für Klarspüler Behälter für Reinigungsmittel Bedien-und Anzeigefeld 8 Typschild Siebe
Gebrauchsanweisung Bedien- und Anzeigefeld Multidisplay Funktions-Tasten 1 2 Startzeit einstellen 3 Kontrollanzeigen EIN-/AUS-Taste 4 Bedienfeld Das Bedienfeld besteht aus den Programmtasten mit LED-Anzeigen und der Taste zum Einstellen der Startzeit. Funktions-Tasten: Zusätzlich zum aufgedruckten Spülprogramm bzw.
Gebrauchsanweisung Vor der ersten Inbetriebnahme Entfernen Sie vor Inbetriebnahme alle Klammern, mit denen die Geschirrkörbe für den Transport gesichert werden. Führen Sie dann folgende Schritte durch: 1. Wasserenthärter einstellen 2. Spezialsalz für Wasserenthärter einfüllen 3. Klarspüler einfüllen 3 10 Spezialsalz und Klarspüler müssen nicht eingefüllt werden, wenn Sie 3-in-1 Reinigungsmitteltabletten verwenden.
Gebrauchsanweisung Wasserenthärter Um Kalkablagerungen auf Geschirr und im Geschirrspüler zu verhindern, muss das Geschirr mit weichem, d.h. kalkarmen Wasser gespült werden. Daher hat der Geschirrspüler einen Wasserenthärter, in dem Leitungswasser ab einer Härte von 4 °d (deutscher Grad) mit Hilfe von Spezialsalz entkalkt wird. 3 Über Wasserhärte und Härtebereich in Ihrem Wohngebiet informiert Sie das zuständige Wasserwerk.
Gebrauchsanweisung Wasserenthärter einstellen 0 Wasserenthärter gemäß Tabelle auf die Wasserhärte Ihres Wohngebietes einstellen: Geschirrspülautomat muss ausgeschaltet sein. Mechanische Einstellung: 1. Tür des Geschirrspülers öffnen. 2. Unteren Geschirrkorb aus dem Geschirrspüler herausnehmen. 3. Härtebereichsschalter auf O oder 1 drehen (siehe Tabelle). 4. Unteren Geschirrkorb wieder einsetzen. Elektronische Einstellung: 5. EIN/AUS-Taste drücken.
Gebrauchsanweisung Spezialsalz für Wasserenthärter 3 Ist die Wasserhärte in Ihrem Wohngebiet unter 4 °d, dann muß das Wasser in Ihrem Geschirrspüler nicht enthärtet werden und Sie benötigen kein Spezialsalz oder Salzersatzstoffe. Sie haben 2 Möglichkeiten, das Wasser zu enthärten: • Wenn Sie Reinigungsmittel verwenden, welches bereits Salzersatzstoffe enthält, wird nur dieses Reinigungsmittel in den Behälter für Reinigungsmittel gegeben.
Gebrauchsanweisung 3 Wenn für die Verwendung von Reinigungsmittel inkl. Spezialsalz der Wasserenthärter elektronisch auf „1“ eingestellt wird, dann wird damit die Kontroll-Anzeige für Spezialsalz abgeschaltet. Spezialsalz einfüllen Wenn Sie Reinigungsmittel und Spezialsalz getrennt verwenden, füllen Sie Spezialsalz ein: – Vor der ersten Inbetriebnahme des Geschirrspülers. – Wenn auf der Bedienblende die Kontrollanzeige für Spezialsalz J leuchtet. 1. Tür öffnen, Unterkorb herausnehmen. 2.
Gebrauchsanweisung Klarspüler Durch den Klarspüler erhält man fleckenfreies, glänzendes Geschirr und klare Gläser. Sie haben 2 Möglichkeiten, Klarspüler zuzuführen: • Wenn Sie Reinigungsmittel verwenden, welches den Klarspüler bereits enthält, wird das Reinigungsmittel inkl. Klarspüler in den Behälter für Reinigungsmittel gegeben. – In diesem Fall muss die Klarspülerzugabe aus dem Vorratsbehälter ausgeschaltet sein, um Doppeldosierung zu vermeiden.
Gebrauchsanweisung Das Multidisplay zeigt die momentane Einstellung an: 0d Klarspülerzulauf ausgeschaltet 1d Klarspülerzulauf eingeschaltet (Voreinstellung ab Werk) 4. Drücken der Funktions-Taste 2 ändert die Einstellung. 5. Zeigt das Multidisplay die gewünschte Einstellung an, EIN/AUS-Taste drücken. Die Einstellung ist dann gespeichert. Klarspüler einfüllen Wenn Sie Reinigungsmittel und Klarspüler getrennt verwenden, füllen Sie Klarspüler ein: – Vor der ersten Inbetriebnahme des Geschirrspülers.
Gebrauchsanweisung Klarspülerdosierung einstellen Beim Geschirrspülen wird aus dem Vorratsfach Klarspüler ins Spülwasser abgegeben. Die Dosierung können Sie von 1-6 einstellen. Vom Werk ist die Dosierung auf „4“ eingestellt. Dosierung nur dann verändern, wenn auf Gläsern und Geschirr Schlieren, milchige Flecken oder angetrocknete Wassertropfen zu sehen sind. (siehe unter „Was tun, wenn...“). 0 1. Geschirrspülertür öffnen. 2. Mit Finger den Entriegelungsknopf des Klarspülerfachs drücken. 3.
Gebrauchsanweisung Signalton ein-, ausschalten Der Signalton kann akustisch melden : – auf welche Wasserhärte der Wasserenthärter eingestellt ist. – wenn ein Spülprogramm beendet ist. – wenn ein Fehler am Geschirrspüler vorliegt. So schalten Sie den Signalton ein / aus: 1. EIN/AUS-Taste drücken. Die LED-Anzeigen aller jetzt anwählbaren Tasten des Bedienfeldes leuchten. 3 Leuchtet nur die LED-Anzeige einer Programmtaste, ist dieses Spülprogramm aktiviert.
Gebrauchsanweisung Im täglichen Gebrauch • Muß Spezialsalz oder Klarspüler nachgefüllt werden ? • Besteck und Geschirr in Geschirrspüler einordnen • Reinigungsmittel für Geschirrspüler einfüllen • Für Besteck und Geschirr geeignetes Spülprogramm auswählen • Spülprogramm starten Besteck und Geschirr einordnen 1 Schwämme, Haushaltstücher und alle Gegenstände, die sich mit Wasser vollsaugen können, dürfen nicht im Geschirrspüler gereinigt werden.
Gebrauchsanweisung Besteck einordnen Vorsicht: Lange, spitze Besteckteile stellen im Besteckkorb, besonders für Kinder eine Gefahrenquelle dar (siehe Sicherheitshinweise)! Damit alle Besteckteile vom Wasser umspült werden, sollten Sie: 0 1. den Gittereinsatz auf den Besteckkorb aufstecken; 2. kurze Messer, Gabeln und Löffel mit dem Griff nach unten in den Gittereinsatz des Besteckkorbs stellen. 3. Für größere Besteckteile, wie z.B. Schneebesen, kann eine Hälfte des Besteckgitters weggelassen werden.
Gebrauchsanweisung Töpfe, Pfannen und große Teller einordnen Größeres und stark verschmutztes Geschirr im Unterkorb einordnen (Teller bis 29 cm Durchmesser). Ihr Geschirrspüler hat eine der vier folgenden Varianten von Unterkörben: Variante 1: Alle Tellereinsätze des Unterkorbs sind fest Variante 2: Die rechten Tellereinsätze des Unterkorbs sind nach links klappbar Um größeres Geschirr leichter einordnen zu können, sind die beiden rechten Tellereinsätze des Unterkorbs nach links klappbar: 0 1.
Gebrauchsanweisung Variante 3: Die rechten Tellereinsätze des Unterkorbs sind überkreuz klappbar 3 Um größeres Geschirr leichter einordnen zu können, sind die beiden rechten Tellereinsätze des Unterkorbs überkreuz klappbar. Variante 4: Beide hintere Tellereinsätze des Unterkorbs sind überkreuz klappbar 3 22 Um größeres Geschirr leichter einordnen zu können, sind die beiden hinteren Tellereinsätze des Unterkorbs überkreuz klappbar.
Gebrauchsanweisung Tassen, Gläser und Kaffeeservice einordnen Kleineres, empfindliches Geschirr und lange, spitze Besteckteile im Oberkorb einordnen. • Geschirrteile auf und unter den klappbaren Tassenauflagen versetzt anordnen, damit das Spülwasser alle Geschirrteile erreicht. • Für hohe Geschirrteile lassen sich die Tassenauflagen hochklappen. • Wein-, Sekt- sowie Cognacgläser in die Ausschnitte der Tassenauflagen lehnen bzw. hängen. • Gläser, Becher usw.
Gebrauchsanweisung Oberkorb in der Höhe verstellen Maximale Höhe des Geschirrs im Oberkorb Unterkorb 3 bei angehobenem Oberkorb 22 cm 31 cm bei abgesenktem Oberkorb 24 cm 29 cm Die Höhenverstellung ist auch bei beladenen Körben möglich. Absenken des Oberkorbs 0 1. Oberkorb ganz herausziehen. 2. Oberkorb bis zum Anschlag anheben und senkrecht absenken. Der Oberkorb rastet in der unteren Position ein. Anheben des Oberkorbs 1. Oberkorb ganz herausziehen. 2.
Gebrauchsanweisung Reinigungsmittel einfüllen 1 Verwenden Sie nur Reinigungsmittel für Geschirrspüler. Füllen Sie Reinigungsmittel ein: – Vor Beginn eines Spülprogramms (nicht beim Programm Vorspülen). Reinigungsmittel wird während des Programms ins Spülwasser abgegeben. Beachten Sie bitte die Dosier- und Lagerempfehlungen der Hersteller auf den Verpackungen der Reinigungsmittel. Das Fach für Reinigungsmittel ist auf der Innenseite der Tür. 0 1.
Gebrauchsanweisung Verwendung von 3-in-1 Reinigungsmitteltabletten Allgemeine Hinweise Bei diesen Produkten handelt es sich um Tabletten mit kombinierten Reinigungsmittel-, Klarspül- und Salzfunktionen. 0 1. Vor Verwendung dieser Produkte müssen Sie zunächst prüfen, ob das Wasser in Ihrem Haushalt die richtige Härte zur Benutzung dieser Produkte aufweist, wie es die Anweisungen des Reinigungsmittelherstellers empfehlen (siehe Produktverpackung). 2.
Gebrauchsanweisung Kompaktreiniger Reinigungsmittel für Geschirrspüler lassen sich anhand ihrer chemischen Zusammensetzung in zwei Grundtypen einteilen: – herkömmliche, alkalische Reiniger mit ätzenden Bestandteilen – niederalkalische Kompaktreiniger mit natürlichen Enzymen. 2 50 °C-Spülprogramme in Verbindung mit Kompaktreinigern entlasten die Umwelt und schonen Ihr Geschirr, denn diese Spülprogramme sind speziell auf die schmutzlösenden Eigenschaften der Enzyme im Kompaktreiniger abgestimmt.
Gebrauchsanweisung Spülprogramm auswählen (Programmtabelle) Wählen Sie mit Hilfe dieser Tabelle das geeignete Spülprogramm aus: Geschirrart zusätzlich Eß- und Kochgeschirr Geschirr ohne Töpfe - - Art der Verschmut- • normal verschmutzt zung • frisch benutzt normal bis leicht verschmutzt • angetrocknete Speisereste besonders geeignet bei Verwendung von Kompaktreinigern.
Gebrauchsanweisung Spülprogramm starten 0 1. Überprüfen Sie, ob Geschirr und Besteck im Geschirrspüler so eingeord- net sind, dass die Sprüharme sich frei drehen können. 2. Wasserhahn ganz aufdrehen. 3. EIN/AUS-Taste drücken. Die LED-Anzeigen aller jetzt anwählbaren Tasten des Bedienfeldes leuchten. 4. Programmtaste für das gewünschte Programm drücken (siehe „Programmtabelle“). Die Programmanzeige leuchtet. Im Multidisplay wird die zu erwartende Restlaufzeit für das Programm angezeigt.
Gebrauchsanweisung 3. Programm-Taste loslassen. 4. Geschirrspülertür schließen. Das neu gewählte Spülprogramm beginnt von vorne. Spülprogramm unterbrechen durch Öffnen der Geschirrspülertür 0 1. Geschirrspülertür öffnen. Das Spülprogramm stoppt. 2. Geschirrspülertür schließen. Das Spülprogramm läuft weiter. Spülprogramm abbrechen (RESET) 0 1. Geschirrspülertür öffnen. 2. Funktions-Tasten 2 und 3 für etwa 1 Sekunde drücken und gedrückt halten.
Gebrauchsanweisung 5. Programmtaste für das gewünschte Programm drücken (siehe „Programmtabelle“). Nach ungefähr 3 Sekunden beginnt das gewählte Spülprogramm. Nach Start des Spülprogramms kann die Zusatzfunktion nicht mehr geändert werden. In diesem Fall muss das Spülprogramm mit RESET abgebrochen und neu gewählt werden. 3 Wenn die Zusatzfunktion einmal dazugewählt wurde, bleibt sie für alle weiteren Spülvorgänge solange erhalten, bis sie durch erneutes Drükken der Taste wieder gelöscht wird.
Gebrauchsanweisung Startzeitvorwahl löschen: Solange das Spülprogramm nicht begonnen hat, können Sie die Startzeitvorwahl löschen. Drücken Sie die Taste b so oft, bis im Multidisplay die Laufzeit des gewählten Programms erscheint. Das gewählte Spülprogramm beginnt sofort nach Schließen der Geschirrspülertür. Spülprogramm wechseln nach Startzeitvorwahl: Solange das Spülprogramm nicht begonnen hat, können Sie durch Drücken einer Programmtaste das Spülprogramm noch wechseln. 0 1.
Gebrauchsanweisung Geschirrspüler ausschalten Wenn der Signalton eingeschaltet ist, ist am Spülprogrammende ein 15 Sekunden langer Dauerton zu hören. Beim Öffnen der Tür, unmittelbar nach Programmende, kann heißer Dampf austreten. Deshalb: 0 1. Tür vorsichtig öffnen. 2. Geschirrspüler mit EIN-/AUS-Taste ausschalten. Alle Anzeigen erlöschen. Wird der Geschirrspüler nicht ausgeschaltet, so wird der Signalton nach 3 Minuten und nach 6 Minuten wiederholt.
Gebrauchsanweisung Reinigung der Siebe Die Siebe im Spülraumboden sind in hohem Grade selbstreinigend. Trotzdem sollten diese gelegentlich kontrolliert und gereinigt werden. Verschmutzte Siebe beeinträchtigen das Spülergebnis. 0 1. Tür öffnen, Unterkorb herausnehmen. 2. Das Siebsystem des Geschirrspülers besteht aus Grob-/Feinsieb, Mikrofilter und Flächensieb. Mit Griff des Mikrofilters das Siebsystem entriegeln und entnehmen. 3.
Gebrauchsanweisung Was tun, wenn... Versuchen Sie mit Hilfe der hier aufgeführten Hinweise kleinere Störungen am Geschirrspüler selbst zu beheben. Wenn Sie bei einer der hier aufgeführten Störungen oder zur Behebung eines Bedienfehlers den Kundendienst in Anspruch nehmen, erfolgt der Besuch des Kundendienst-Technikers auch während der Garantiezeit nicht kostenlos. ...Fehlermeldungen angezeigt werden.
Gebrauchsanweisung Störung Es sind 2 kurze Warntöne zu hören, die ständig wiederholt werden, die Programmanzeige des gewählten Spülprogramms blinkt, das Multidisplay zeigt den Fehlercode Å 20 an. Es sind 3 kurze Warntöne zu hören, die ständig wiederholt werden, das Multidisplay zeigt den Fehlercode Å 30 an. Mögliche Ursache Der Siphon ist verstopft. Abhilfe Siphon reinigen. Wasserablaufschlauch Schlauchverlegung ist nicht korrekt verlegt. überprüfen.
Gebrauchsanweisung ...es Probleme beim Betrieb des Geschirrspülers gibt. Störung Programm startet nicht. Mögliche Ursache Abhilfe Geschirrspülertür ist nicht richtig geschlossen. Tür schließen. Netzstecker ist nicht eingesteckt. Netzstecker einstecken. Sicherung der Hausinstallation ist nicht in Ordnung. Sicherung ersetzen. Bei Geschirrspülermodellen Falls Geschirr sofort gespült mit Startzeitvorwahl: werden soll, StartzeitvorEine Startzeit ist vorgewählt. wahl löschen.
Gebrauchsanweisung Auf Gläsern und Geschirr sind Schlieren, Streifen, milchige Flecken oder blauschimmernder Belag. – Klarspülerdosierung niedriger einstellen. Auf Gläsern und Geschirr sind angetrocknete Wassertropfen. – Klarspülerdosierung höher einstellen. – Der Reiniger kann die Ursache sein. Kontaktieren Sie den Kundenberater des Reinigungsmittelherstellers. Technische Daten Fassungsvermögen: 12 Maßgedecke einschließlich Servicegeschirr Zulässiger Wasserdruck: 1-10 bar (=10-100 N/cm2 = 0.1-1.
Gebrauchsanweisung Hinweise für Prüfinstitute Die Prüfung nach EN 60704 muß bei voller Beladung mit dem Testprogramm (siehe Programmtabelle) durchgeführt werden. Die Prüfungen nach EN 50242 müssen mit vollem Salzbehälter des Wasserenthärters, mit vollem Vorratsbehälter für Klarspüler und mit dem Testprogramm (siehe Programmtabelle) durchgeführt werden. Volle Beladung: 12 Maßgedecke einschl. Servicegeschirr Halbvolle Beladung: 6 Maßgedecke einschl.
Aufstell- und Anschlußanweisung AUFSTELL- UND ANSCHLUßANWEISUNG Aufstellen des Geschirrspülers • Geschirrspüler muß standsicher und waagrecht ausgerichtet auf festem Boden aufgestellt werden. • Um Bodenunebenheiten auszugleichen und Gerätehöhe an andere Möbel anzugleichen, Schraubfüße herausschrauben: – mit einem Schraubendreher. • Bei Unterbau-, integrierbaren und vollintegrierbaren Geschirrspülern sind die hinteren Gerätefüße mit einem Schraubendreher vorne am Gerät einzustellen.
Aufstell- und Anschlußanweisung Montage der Möbelplatte (siehe beiliegende Montageschablone) 3 Die Gerätetür kann mit einer Holzplatte/Möbelplatte folgender Abmessungen verkleidet werden: Breite: 591 mm – 594 mm Dicke: 16 mm – 24 mm Höhe: max. 715 mm Gewicht: max.
Aufstell- und Anschlußanweisung Anschließen des Geschirrspülers Wasseranschluss Der Geschirrspüler hat Sicherheitseinrichtungen, die den Rückfluss von Spülwasser in das Trinkwasser-Leitungsnetz verhindern und den geltenden wassertechnischen Sicherheitsvorschriften entsprechen. • Der Geschirrspüler kann an Kaltwasser und an Warmwasser bis max. 60 °C angeschlossen werden. • Der Geschirrspüler darf nicht an offene Warmwassergeräte und Durchlauferhitzer angeschlossen werden.
Aufstell- und Anschlußanweisung 3 Das folgende Kapitel gilt nur für Geschirrspüler, die an der Schlauchverschraubung zum Wasserhahn ein Sicherheitsventil haben: Zulaufschlauch mit Sicherheitsventil Nach Anschluss des doppelwandigen Zulaufschlauchs befindet sich das Sicherheitsventil direkt am Wasserhahn. Daher steht der Zulaufschlauch nur während des Wasserzulaufs unter Druck.
Aufstell- und Anschlußanweisung Wasserablauf Ablaufschlauch 1 Der Ablaufschlauch darf nicht geknickt, gequetscht oder in sich verschlungen sein. • Anschluß des Ablaufschlauches: – maximal zulässige Höhe: 1 Meter. – minimal erforderliche Höhe 40cm über der Geräteunterkante. Verlängerungsschläuche • Verlängerungsschläuche sind über den Fachhandel oder unseren Kundendienst zu beziehen. Der Innendurchmesser der Verlängerungsschläuche muß 19 mm betragen, damit die Gerätefunktion nicht gestört wird.
Aufstell- und Anschlußanweisung Wasserschutzsystem Zum Schutz gegen Wasserschäden ist der Geschirrspüler mit einem Wasserschutzsystem ausgestattet. Im Fehlerfall unterbricht das Sicherheitsventil im Zulaufschlauch sofort den Wasserzulauf und die Entleerungspumpe schaltet sich ein. Damit kann Wasser weder aus- noch überlaufen. Im Gerät befindliches Restwasser wird automatisch abgepumpt. 1 Das Wasserschutzsystem funktioniert auch, wenn das Gerät ausgeschaltet ist.
Aufstell- und Anschlußanweisung Anschlußtechnik Zulauf- und Ablaufschläuche sowie das Netzkabel müssen seitlich vom Geschirrspüler angeschlossen werden, da hinter dem Gerät kein Platz dafür ist. Das nachfolgende Beispiel einer Sanitär- und Elektroinstallation kann nur eine Empfehlung sein, da maßgebend die Gegebenheiten am Aufstellort sind (vorhandene Anschlüsse, örtliche Anschlußvorschriften der Energie- bzw. der Wasserwerke, usw...).
Kundendienststellen KUNDENDIENSTSTELLEN Deutschland Sehr geehrter Kunde, der Werkskundendienst von AEG Hausgeräte ist dezentral organisiert. Damit bieten wir Ihnen überall einen zuverlässigen Service. Unter der für Sie kostengünstigen Rufnummer 0180 322 66 22 (EUR 0.09 / Minute) Deutsche Telekom/ Stand Jan. 2002 können Sie im Bedarfsfall einen unserer Spezialisten oder Service-Partner anfordern. Ihre Ersatzteil-Bestellung geben Sie bitte unter der zentralen Rufnummer 0180 5 00 10 76 auf. (EUR 0.
Kundendienststellen PLZ Adresse 41541 Dormagen-St. Peter Sachtlebenstraße 1 46562 Voerde* Friedrich-Wilhelm-Straße 22 48165 Münster* Zum Kaiserbusch 1 49084 Osnabrück* Pferdestraße 23 52068 Aachen* Auf der Hüls 197 56068 Koblenz* Rheinstraße 17 56070 Koblenz* A.-Hosch-Str.
Kundendienststellen Weitere Service-Stellen sind in: 03222 Groß Klessow 06896 Wittenberg-Reinsdorf 15517 Fürstenwalde 16515 Oranienburg 17039 Ihlenfeld 19057 Schwerin 24354 Rieseby 26639 Wiesmoor 27726 Worpswede 30900 Wedemark 32825 Blomberg 34497 Korbach 36043 Fulda 39114 Magdeburg 49377 Vechta 63906 Erlenbach 78244 Bietingen 84307 Eggenfelden 87549 Rettenberg 99819 Ettenhausen 49
Kundendienststellen Österreich Adresse Bereich Electrolux Hausgeräte GmbH Telefon Telefax 01/ 8 66 40-0 01/ 8 66 40-305 Herziggasse 9 Ersatzteilverkauf 01/ 8 66 40-315 1230 Wien Reparaturannahme 01/ 8 66 40-330 kundendienst@electrolux.co.at Technische Auskünfte 01/ 8 66 40-399 01/ 8 66 40-300 01/ 8 66 40-300 Werkskundendienst für die Marken AEG - Electrolux - Juno - Zanussi 50 Adresse Telefon Telefax Hausgeräte Kundendienst GmbH Winetzhammerstraße 8 4030 Linz hg.kundendienst.linz@aon.
Garantiebedingungen GARANTIEBEDINGUNGEN Deutschland Der Endabnehmer dieses Gerätes (Verbraucher) hat bei einem Kauf dieses Gerätes von einem Unternehmer (Händler) in Deutschland im Rahmen der Vorschriften über den Verbrauchsgüterkauf gesetzliche Rechte, die durch diese Garantie nicht eingeschränkt werden. Diese Garantie räumt dem Verbraucher also zusätzliche Rechte ein.
Garantiebedingungen Österreich Sehr geehrte Kunden! Wir, die Electrolux Hausgeräte GmbH, beglückwünschen Sie zum Erwerb eines Gerätes aus dem Electrolux Konzern. Für dieses Gerät räumen wir Ihnen, gemäß den nachstehenden Bedingungen, eine besondere Garantie ein, die Ihnen also zusätzliche Rechte gewährt. 1. Die Garantie beginnt mit dem Tag an dem das Gerät gekauft wurde und erstreckt sich über einen Zeitraum von 24 Monaten. Wir empfehlen daher, den Kaufbeleg unbedingt aufzubewahren. 2.
Service SERVICE Im Kapitel „Was tun, wenn...“ sind die wichtigsten Fehlerquellen zusammengestellt, die Sie selbst beheben können. Wenn Sie trotzdem für einen der aufgeführten Hinweise oder aufgrund von Fehlbedienung den Kundendienst in Anspruch nehmen, so erfolgt der Besuch des Kundendienst-Technikers auch während der Garantiezeit nicht kostenlos. Wenn Sie für eine Störung keinen Hinweis in dieser Gebrauchsanweisung finden, wenden Sie sich bitte an den Kundendienst.
From the Electrolux Group. The world´s No.1 choice. Die Electrolux-Gruppe ist der weltweit größte Hersteller von gas- und strombetriebenen Geräten für die Küche, zum Reinigen und für Forst und Garten. Jedes Jahr verkauft die Electrolux-Gruppe in über 150 Ländern der Erde über 55 Millionen Produkte (Kühlschränke, Herde, Waschmaschinen, Staubsauger, Motorsägen und Rasenmäher) mit einem Wert von rund 14 Mrd. USD. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.