FAVORIT 65050 VI Fully Integrated Dishwasher User Instructions
Dear customer, Please read these user instructions carefully. Please observe the safety instructions on the first few pages of these user instructions! Please keep these user instructions for later reference. Pass them on to any subsequent owner of the appliance. 1 0 The warning triangle and/or specific words (Warning!, Caution!, Important!) are used to highlight instructions that are important for your safety or for the function of the appliance. It is imperative that these instructions are observed.
Contents CONTENTS Operating Instructions .................................... 5 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Economical and Ecological Dishwashing . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Appliance Features, Display and Control Panel . . . . . . . . . . . . . . . . . . .
Contents Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Cleaning the Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 What to do, if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...Error messages are displayed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...there are problems with the operation of the dishwasher. . . . .
Operating Instructions OPERATING INSTRUCTIONS 1 Safety Instructions The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law. Nevertheless, as a manufacturer we consider it our obligation to make you aware of the following safety information: Installation, Connection and Placing into Operation • The dishwasher may only be transported upright. • Check the dishwasher for transport damage.
Operating Instructions • Never place the dishwasher in operation if the mains cable, water inlet or drain hose is damaged; or the control panel, work top or plinth area is damaged such that the inside of the appliance is freely accessible. • If the mains lead is damaged, or is to be replaced for a longer lead, the cable (obtainable from AEG Service Force) must be replaced by a service engineer authorised by AEG. • Never unplug the appliance by pulling on the cable, always pull the plug.
Operating Instructions • In the event of a fault, first close the tap, then switch off the appliance and unplug it from the mains. If the appliance is permanently wired to the mains: remove the fuse. 2 Disposal Disposing of the Packaging Material Dispose of the dishwasher packaging material correctly. All the packaging materials used are harmless to the environment and can be recycled. • Plastic parts are marked with standard international abbreviations: – >PE< for polyethylene, e.g.
Operating Instructions Appliance Features, Display and Control Panel Top Spray Nozzle Rubber Seal for Connecting the Water Feed to the Spray Arm Spray Arms Water Hardness Switch Container for Special Salt Container for Rinse Aid Detergent Dispenser Display and Control Panel 8 Rating plate Filters
Operating Instructions Display and control panel Multi-display Function buttons 1 2 3 Indicators ON/OFF button 4 Set start delay Function buttons: In addition to the programme and/or start delay selected, the following functions can also be set with the help of these buttons: Function button 1 Set water softener Function button 2 Activate/deactivate rinse aid inflow Function button 3 Activate/deactivate acoustic signal Function button 4 - not programmed - The multi-display can indicate: – t
Operating Instructions Prior to using for the first time Prior to using for the first time, remove all the clips with which the baskets are secured for transport. Then perform the following steps: 0 1. Adjust the water softener 2. Fill with Salt for the Water Softener 3. Fill with Rinse Aid Water softener To avoid scale deposits on the dishes and in the dishwasher, the dishes must be washed with soft water, i.e. water with a low lime content.
Operating Instructions 1) The water hardness will only be indicated acoustically if the acoustic signal has been activated. 2) (°d) German degree, measure of the hardness of water 3) [mmol/l] millimol per litre, international unit for the hardness of water 4) On this setting the length of the programme may be slightly longer.
Operating Instructions 9. When the hardness setting is correct, press the ON/OFF switch. The hardness setting is now saved. Special salt for the water softener 3 If the water hardness in your area is less than 4 °d, then the water in your dishwasher does not need to be softened and you do not need to use special salt or salt substitute.
Operating Instructions 0 1. Set the water softener manually and electronically to the desired water hardness: 3 Manual setting Electronic setting Multi-display indicator Addition of special salt 0 1 IL Do not add special salt. 0-1 2-10 2l to 10l Addition of special salt via salt container (factory setting) If the water softener is electronically set at “1” for the purpose of using detergent that includes special salt, the special salt indicator is deactivated.
Operating Instructions 6. Turn the lid clockwise to the stop, otherwise dishwasher salt will leak into the wash water, this could lead to poor wash results. To avoid this run a rinse programme after filling the salt container with special salt. This will wash away salt water and any salt crystals that have been spilt. Depending on the size of the salt grains, it can take several hours for the salt to dissolve in the water and the special salt indicator J to extinguish.
Operating Instructions 3 If the only LED indicator illuminated is one that belongs to a programme button, this means that this programme has been activated. The Programme must be cancelled (RESET): Press function buttons 2 and 3 simultaneously for approx. 1 second. The LED indicators for all the buttons in the control panel that are now able to be selected will become illuminated. 2. Press function buttons 2 and 3 simultaneously and keep them pressed.
Operating Instructions 4. Fill with rinse aid exactly up to the level marked “max”; this corresponds to a quantity of approx. 140 ml. 5. Close the lid and press until it locks into place. 6. Wipe up any spilt rinse aid with a cloth. Otherwise too much foam will be formed during the wash. Adjusting Rinse Aid Dosing 3 As the dishes are washed rinse aid is released from the dispenser into the wash water. The dose is factory set at 4, and can be adjusted from 1 to 6.
Operating Instructions Activating/deactivating the acoustic signal The acoustic signal can indicate acoustically: – at which water hardness the water softener is set. – when a programme has finished. – when an error has occurred with the dishwasher. You can switch on/off the acoustic signal in the following way: 1. Press the ON/OFF button. The LED indicators for all the buttons in the control panel that are now able to be selected will become illuminated.
Operating Instructions In Daily Use • Check the salt and rinse aid levels. • Load cutlery and dishes into the dishwasher • Fill with dishwasher detergent • Select a wash programme suitable for the cutlery and dishes • Start the wash programme Loading Cutlery and Dishes 1 Sponges, household cloths and any object that can absorb water should not be washed in the dishwasher.
Operating Instructions – To avoid damage to glasses, they must not touch – Do not lay small objects (e.g. lids) in the cutlery rack Loading Cutlery 1 Long bladed knives stored in an upright position are a potential hazard. 1 Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Take care when loading or unloading sharp items such as knives. To ensure that all items of cutlery are completely washed, you should 0 1.
Operating Instructions On some models of dishwasher it is possible to open the cutlery basket. To ensure that the cutlery rack cannot open on removal from the appliance, you should always hold both parts of the two part handle. 0 1. Place the cutlery rack on a table or work surface 2. Open the two part handle 3. Remove cutlery 4. Close the two part handle.
Operating Instructions Loading Pans, Frying Pans and Large Plates Load large and heavily soiled dishes in the lower basket (Plates up to 29cm in diameter). Your dishwasher has one of the following four types of lower basket: Type 1: None of the plate inserts in the lower basket can be removed Type 2: The right-hand plate inserts in the lower basket can be folded over to the left 3 To ease the loading of large items, the two right-hand plate inserts in the lower basket can be folded over to the left 1.
Operating Instructions Type 3: The right-hand plate inserts in the lower basket can be folded across one another 3 To ease the loading of large items, the two right-hand plate inserts in the lower basket can be folded across one another. Type 4: The two rear plate inserts in the lower basket can be folded across one another 3 22 To ease the loading of large items, the two rear plate inserts in the lower baskets can be folded across one another.
Operating Instructions Loading Cups, Glasses and Coffee Services Load small, delicate items and long pointed cutlery in the upper basket. • Arrange items of crockery on the folding cups racks so that they are offset from each other and water can reach all items. • The cup racks can be folded up out of the way for tall items. • Lay or hang wine, champagne, and brandy glasses in the cut outs on the cup racks. • Glasses, beakers, etc.
Operating Instructions Adjusting the Height of the Upper Basket Maximum Height of the Dishes in the Upper Basket Lower Basket 3 With upper basket raised 22 cm 31 cm With upper basket lowered 24 cm 29 cm The height of the basket can also be adjusted when it is loaded. Lowering the Upper Basket: 0 1. Pull the upper basket out completely. 2. Holding the upper basket at the rear right, lift it as far as it will go and then lower it vertically. The upper basket will engage in the lower position.
Operating Instructions Filling with Detergent 1 Only use dishwasher detergent. Fill with detergent: – Prior to the start of a wash programme (not for the pre wash programme). The detergent is released into the wash water during the programme. Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging. The detergent compartment is on the inside of the dishwasher door. 0 1. If the lid is closed: press release button (1). The lid springs open. 2 2.
Operating Instructions Use of "3 in 1"/ Combi Detergent Tablets General Advice These products are tablets with combined detergent/rinse-aid and salt functions. 0 1. Before using these products you should first check that the water hardness in your supply is compatible with the use of these products as per the detergent manufacturers instructions (on the product packaging). 2. These products should be strictly used according to the detergent manufacturers instructions.
Operating Instructions Concentrated Detergent Based on their chemical composition, dishwasher detergents can be split into two basic types: – conventional, alkaline detergents with caustic components – low alkaline concentrated detergents with natural enzymes.
Operating Instructions Selecting the programme (Programme Table) Choose the most suitable programme with the aid of this table: Type of dishes Including Dinner service and cooking items - - Type of soil- • heavily soiled ing • normally soiled • dried-on left- • dried-on overs, leftovers in particular egg white and thickeners Suitable programme: Cycle sequence 3 Consumption values: 4 INTENSIV 70° Pre-wash Main wash 2x intermediate rinses Final rinse Dry ò AUTO Pre-wash Main wash Intermediate rinse
Operating Instructions Starting a programme 0 1. Check that the dishes and cutlery are loaded in the dishwasher in such a way that the spray arms are free to rotate. 2. Turn on the tap fully. 3. Press the ON/OFF button. The LED indicators for all the buttons in the control panel that are now able to be selected will become illuminated. 4. Press the relevant button for the programme required (see “Programme Table”). The programme display will become illuminated.
Operating Instructions After several seconds only the indicator for the new programme will be flashing. 3. Release the programme button. 4. Close the dishwasher door. The newly selected programme will commence from the beginning. Interrupting the programme by opening the dishwasher door 0 1. Open the door of the dishwasher. The programme will stop. 2. Close the dishwasher door. The programme will continue. Aborting the programme (RESET) 0 1. Open the door of the dishwasher. 2.
Operating Instructions Changing the start delay: As long as the programme has not started, you are still able to cancel the start delay by pressing the b button. Cancelling the start delay: As long as the programme has not started you are still able to cancel the start delay. Continue pressing the b button until the length of the selected programme appears in the multi-display. The selected programme will begin immediately after the dishwasher door has been closed.
Operating Instructions Switching off the dishwasher If the acoustic signal has been enabled, a continuous tone will sound for 15 seconds at the end of the programme. Hot steam may escape if the door is opened immediately after the programme has ended. Therefore: 0 1. Open the door carefully. 2. Switch off the dishwasher by pressing the ON/OFF button. All display indicators will go out. If you do not switch off the dishwasher, the acoustic signal will sound again 3 minutes later and 6 minutes later.
Operating Instructions Cleaning the Filter The filters should be checked and cleaned regularly. Dirty filters will give poor wash results. 0 1. Open the door, remove the lower basket. 2. The dishwasher filter system comprises a coarse/fine filter, microfilter and a flat filter. Unlock the filter system using the handle on the microfilter, and remove. 3. Turn the handle about ¼ a turn anticlockwise and remove. 4.
Operating Instructions What to do, if ... Try to rectify minor faults on the dishwasher with the aid of the instructions given here. If you call an engineer to resolve a of fault listed here, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is in guarantee. ...Error messages are displayed. If your appliance is equipped with an optical floor signal, in the event of an error a dot-shaped optical signal will flash on the floor.
Operating Instructions Malfunction Two short continuously repeated warning tones can be heard; the programme display for the selected programme is flashing; error code Å 20 is displayed in the multi-display. Possible cause Remedy The siphon is blocked. Clean out siphon. The water drain hose has not been correctly laid. Check hose installation.
Operating Instructions ...there are problems with the operation of the dishwasher. Symptom Possible Cause Solution The door of the dishwasher is Shut the door. not closed properly. Mains plug is not plugged in. Insert mains plug. The programme does not start. House fuse is defective. Replace fuse. A start delay is selected. If dishes are to be washed immediately cancel delay start timer. The washing compartment is made from rust-free stainless steel.
Operating Instructions There are streaks, milky spots or a bluish coating on glasses and dishes. – Lower rinse aid dosing. There are dried water drops on the glasses and dishes. – Increase rinse aid dosing. – The detergent may be the cause. Contact the detergent manufacturer’s customer advisor. Technical Data Capacity: 12 place settings including serving dishes Permitted Water Pressure: 1-10 bar (=10-100 N/cm2 = 0.1-1.
Operating Instructions Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme (see Programme Table). Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see Programme Table). Full Load: 12 place settings incl. serving dishes Half Load: 6 place settings incl.
Installation and Connection Instructions INSTALLATION AND CONNECTION INSTRUCTIONS Installing the Dishwasher • The dishwasher must be installed on a firm floor and adjusted to ensure that it is stable and level. • To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units extend the threaded feet by unscrewing: – use a screwdriver.
Installation and Connection Instructions Fitting the Furniture Door Panel (see installation template supplied) 3 40 The door of the appliance can be fitted with a furniture door panel of the following dimensions: Width: 591 mm – 594 mm Thickness: 16 mm – 24 mm Height: max. 715 mm Weight: max.
Installation and Connection Instructions Connecting the Dishwasher Water Connection The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations. • The dishwasher must be connected to a cold water supply. • The dishwasher must not be connected to open hot water appliances or instantaneous water heaters.
Installation and Connection Instructions 3 The following section is only applicable to dishwashers that have a safety valve on the threaded hose fitting for the tap: Water inlet hose with safety valve After connecting the double-walled water inlet hose, the safety valve is next to the tap. Therefore the water inlet hose is only under pressure while the water is running.
Installation and Connection Instructions Water drain Drain hose 1 The drain hose must not be kinked, crushed or entangled. • Connecting the drain hose: – Maximum permitted height: 1 metre. – Minimum required height 40 cm above the lower edge of the machine. Extension hoses • Extension hoses are available from AEG Service Force. The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded.
Installation and Connection Instructions Leak prevention system To avoid damage caused by water leakage, the dishwasher is equipped with a leak prevention system. In the event of a fault, the safety valve in the appliance immediately interrupts the inflow of water and the drain pump is activated. In this way water can neither escape nor overflow. Any remaining water in the appliance is automatically pumped out.
Installation and Connection Instructions • The wire coloured green and yellow must be connected to the terminal marked with the letter “E“ or by the earth symbol or coloured green and yellow. • The wire coloured blue must be connected to the terminal “N“ or coloured black. • The wire coloured brown must be connected to the terminal marked “L“ or coloured red. • Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath.
Guarantee Conditions GUARANTEE CONDITIONS Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate.
Service and Spare parts SERVICE AND SPARE PARTS In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact Service Force by telephoning: 08705 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.
From the Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.