FAVORIT 65070 U Dishwasher User information
Dear Customer, Please read this user information carefully and keep it to refer to later. Please pass the user information on to any future owner of the appliance. 1 3 2 3 2 The following symbols are used in the text: Safety instructions Warning! Information that affects your personal safety. Important! Information that prevents damage to the appliance. Useful tips and hints Environmental information Your dishwasher is fitted with the new “PULSE WASH” dishwashing system.
Contents Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Diagram of Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Prior to Using for the First Time. . . . . . . .
Operating Instructions 1 Safety Prior to using for the first time • Follow the ”Instructions for installation and connection”. Correct Use • The dishwasher is only intended for washing domestic dishes. • Additions or modifications to the dishwasher are not permitted. • Use only special salt, detergent and rinse aid suitable for domestic dishwashers. • Do not put any solvents in the dishwasher. This could cause an explosion. Child Safety • Keep packaging away from children. There is a risk of suffocation.
Diagram of Appliance Top Spray Nozzle Upper basket spray arm and lower spray arm Water softener unit. Dispenser for special salt Detergent Dispenser Rinse aid dispenser Rating plate Filters Control Panel ON/OFF button The ON/OFF button is used to turn the dishwasher on and off.
Programme buttons 1 2 Multi-display 4 3 Set delay timer Control indicators Function buttons The Programme buttons are used to select the desired dishwashing cycle.
The control indicators have the following meanings: 1) Refill with special salt 1) Refill with rinse aid 3 IN 1 3 in 1 function activated 1) These control indicators are never illuminated while a dishwashing cycle is running. Prior to Using for the First Time 3 3 1. Set the water softener 2. Fill up with special salt for water softeners 3. Fill up with rinse aid If you wish to use 3in1 detergent: First read the section “Using 3in1 detergents”. 1. Press the ON/OFF button.
Setting the Water Softener 3 The water softener must be set manually and electronically: To avoid scale deposits on the dishes and in the dishwasher, the dishes must be washed with soft water, i.e. water with a low lime content. The water softener must be set according to the table to the water hardness in the area where you live. Your local water company will be able to give you information about the water hardness in your area. The dishwasher must be switched off. Setting manually: 1.
Adjusting the hardness setting Water hardness in °d1)) in mmol/l2)) 51 - 70 43 - 50 37 - 42 29 - 36 23 - 28 9,0 - 12,5 7,6 - 8,9 6,5 - 7,5 5,1 - 6,4 4,0 - 5,0 IV 19 - 22 15 - 18 3,3 - 3,9 2,6 - 3,2 III 11 - 14 1,9 - 2,5 II 4 - 10 0,7 - 1,8 I/II below 4 below 0.7 I Range Indication on the multi-display Manual Electronic 1 103) 9 8 7 6 10L .
Adding Special Salt 3 3 10 To decalcify the water softener, it must be filled up with special salt. Use only special salt suitable for domestic dishwashers. If you do not use 3 in1 detergent, fill up with special salt: – Before using the dishwasher for the first time. – When the control indicator for special salt is illuminated on the control panel. 1. Open the door and remove the lower basket. 2. Screw open the lid on the salt dispenser by turning it anti-clockwise. 3.
Filling Up with Rinse Aid Rinse aid causes the rinse water to flow easily from the crockery leaving gleaming dishes and glassware. If you do not use 3in1 detergent, fill up with rinse aid: – Before using the dishwasher for the first time. – When the control indicator for rinse aid is illuminated on the control panel. Use only special rinse aid for dishwashers. 1. Open the door. The rinse aid compartment is located on the inside of the dishwasher door. 2.
Setting the Amount of Rinse Aid Required 3 Only change the amount dispensed, if smears, milky spots (reduce the amount) or dried on water spots (increase the amount) can be seen on glasses and dishes. (See section “If dishwashing results are not satisfactory”.) The dosage can be set from 1-6. The dosage is pre-set to “4” in the factory. 1. Open the dishwasher door. 2. Press the release button on the rinse aid compartment. 3. Open the cover. 4. Set the dosage level. 5.
In daily use Loading cutlery and dishes 1 Sponges, cleaning cloths and any other objects that can absorb water must not be washed in the dishwasher. Plastic and Teflon-coated dishes and pans tend to retain water droplets. These dishes and pans therefore do not dry as well as those made of china and stainless steel.
Loading cutlery 1 Warning: Sharp knives and other items of cutlery with sharp edges must be laid in the cutlery rack or in the upper basket to avoid the risk of injury. To ensure that all items of cutlery in the cutlery basket can be reached by the water, you should: 1.Place the grid insert on the cut- 2.Place forks and spoons in the lery basket cutlery basket's grid insert with their handles pointing downwards. For larger utensils, such as whisks, leave off one half of the cutlery grid.
To make it easier to load larger dishes, the two plate racks on the right in the lower basket can be folded down. Cups, Glasses, Coffee Service Load smaller, fragile crockery and long, sharp cutlery in the upper basket. • Arrange items of crockery on and under the folding cup racks so that they are offset from each other and water can reach all items. • The cup racks can be folded up out of the way for tall crockery items. • Lay or hang wine and brandy glasses in the slots in the cup racks.
Adjusting the Height of the Upper Basket Maximum height of dishes in the 3 Upper basket Lower basket with upper basket raised 22 cm 30 cm with upper basket lowered 24 cm 29 cm The height of the baskets can also be adjusted when they are loaded. Raising/Lowering the Upper Basket 1. Pull out the upper basket completely. 2. Raise the upper basket as far as it will go and then lower it vertically. The upper basket will latch into the lower or the upper position.
Adding Detergent 1 Detergents remove the dirt from dishes and cutlery. The detergent must be added before the cycle starts. Only use detergent intended for domestic dishwashers. The detergent compartment is located on the inside of the door. 1. If the lid is closed: Press the release button. The lid will spring open. 3 2. Place the detergent in the detergent dispenser. The markings indicate the dosing levels for powder detergents: “20/30” corresponds to approx. 20/30 ml of detergent.
Concentrated detergents 2 Today’s detergents for dishwashers are almost exclusively low-alkaline concentrated detergents with natural enzymes in tablet or powder form. Using 50°C dishwashing cycles in conjunction with these concentrated detergents reduces pollution and is good for your dishes, as these dishwashing cycles are specially matched to the dirt-dissolving properties of the enzymes in concentrated detergents.
Selecting the dishwashing cycle (Cycle Table) - • - • - Dinner service and cookware heavily soiled, dried-on food remains, in particular protein and starch • • 2x • • Dinner service and cookware, normally soiled temperaturesensitive dishes • • • • 130 - 160 0,95 - 1,05 13 - 15 Dessert dishes and coffee lightly soiled service, delicate glasses - • 2x • • 0,9 15 ECO 50° 5) 13 - 25 Water (litres) just used, lightly to normally soiled • 23 - 25 1,8 - 2,0 120 - 130 9 Dishes, exc
Starting a Dishwashing Cycle 3 1. Check that the spray arms can turn freely. 2. Turn the water tap on fully. 3. Close the door. 4. Press the ON/OFF button. 5. Select the desired cycle. The programme indicator comes on. The remaining time expected for the cycle will be shown in the multi-display. The selected cycle will begin after approximately 3 seconds. During the dishwashing cycle, the remaining time shown in the multidisplay may be adjusted according to the size of the load, degree of soiling, etc.
Setting the Delay Timer 3 With the delay timer you can delay the start of a dishwashing cycle for between 1 and 19 hours. 1. Press the Delay Timer button repeatedly until the multi-display shows the desired time delay, for example 12h, if the cycle is to start in 12 hours. The Delay Timer indicator is illuminated. 2. Select dishwashing cycle. 3. The time remaining to the start of the cycle is continuously displayed (e. g. 12h, 11h, 10h, … 1h etc.).
Care and cleaning 1 Do not use furniture care products or aggressive cleaners. • When necessary, clean the dishwasher’s controls with a soft cloth. • Occasionally check the internal dispensers, door seal and water inlet filter (if fitted) for dirt and clean them, if necessary. Cleaning the Filters 3 The filters must be regularly checked and cleaned. Dirty filters will spoil the wash results. 1. Open the door and remove the lower basket. 2.
What to do if... Remedying small malfunctions If one of the following fault codes is displayed in the multi-display during operation: – Fault codeÅ 10 (Problems with water inlet), – Fault codeÅ 20 (Problems with water drainage), please have a look at the following table. When the fault is remedied, press the button for the cycle that has started. The cycle will continue. With other fault codes (“Å ” followed by a number): – Abort the dishwashing cycle. – Switch the appliance off and on again.
Malfunction The cycle indicator for the selected dishwashing cycle is flashing, fault code Å 20 is displayed in the multi-display. (Problems with water drainage) Fault code Å 30 is displayed in the multi-display. The cycle is not starting. Possible cause The sink outlet is blocked. Remedy Clean out sink outlet. Water drain hose Check the position of the has not been correctly posihose. tioned. The anti-flood system has been triggered.
If the Dishwashing Results are not Satisfactory The dishes are still dirty. • The wrong dishwashing cycle was selected. • The dishes were loaded is such a way that the dishwashing water did not reach all items. The baskets for the dishes must not be overloaded. • The filters in the base of the washing compartment are dirty or incorrectly positioned. • Good quality detergent was not used, or too little was used.
Disposal 2 2 1 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at your local waste disposal facilities. Old appliance Please dispose of your old appliance in line with the guidelines for disposal in your area. Warning! When your appliance has finished its working life, remove the plug from the socket.
Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test cycle (see “Cycle Table”). Tests in accordance with EN 50242 must be carried out when the salt dispenser in the water softener and the rinse aid dispenser have been filled with salt and rinse aid respectively, and using the test cycle (see “Cycle Table”).
Lower basket with cutlery basket 28 Cutlery basket
Installation and connection instructions 1 Safety Information for the Installation • Only transport the dishwasher in an upright position, otherwise salt water may run out. • Before using the dishwasher for the first time, check for any damage caused in transport. Do not under any circumstances connect an appliance that is damaged. In the case of damage, please contact your supplier.
Installing the Dishwasher • The dishwasher must be installed on a firm floor and adjusted to ensure that it is stable and level in all directions. • To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units, extend the threaded feet using a screwdriver. • Adjust the rear feet of the appliance using a screwdriver from the front of the appliance. (See installation instructions.
Connecting the dishwasher Connecting to the water supply • The dishwasher can be connected to cold and hot water supplies up to max. 60°C. • The dishwasher must not be connected to open hot water appliances or instantaneous water heaters. Permitted water pressure Lowest permitted water pressure: 1 bar (=10 N/cm2 =100 kPa) Consult your plumber if the water pressure is less than 1 bar.
Water drainage 1 Drain hose The drain hose must not be kinked, crushed or entangled. Connecting the drain hose: – Maximum permitted height: 1 metre. – Minimum required height: 40 cm above the bottom edge of the appliance. Extension hoses • Extension hoses are available from your dealer or from your local Service Force Centre. To ensure that the function of the appliance is not impeded, the internal diameter of extension hoses must be 19 mm.
Anti-flood system For protection from water damage, the dishwasher is equipped with a anti-flood system. In the event of a fault, the safety valve in the water inlet hose immediately interrupts the supply of water to the appliance and the drain pump is activated. In this way water can neither escape nor overflow. The remaining water in the appliance is automatically pumped out.
Electrical Connection 1 Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING - This appliance must be earthed. The manufacturer declines any responsibility should these safety measures not be observed. Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. To isolate the dishwasher from the mains, remove the mains plug.
Connecting systems The water inlet hose, drain hose and the mains cable must all be connected to the side of the dishwasher as there is no space for them behind the appliance.
Warranty conditions Great Britain Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate.
Service and Spare Parts If the event of your appliance requiring service, or if you wish to purchase spare parts, please contact Service Force by telephoning: 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce.co.
From the Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.
