ÖKO_FAVORIT 80800 Dishwasher User Instructions
Dear customer, Please read these user instructions carefully. Please observe the safety instructions on the first few pages of these user instructions! Please keep these user instructions for later reference. Pass them on to any subsequent owner of the appliance. 1 0 The warning triangle and/or specific words (Warning!, Caution!, Important!) are used to highlight instructions that are important for your safety or for the function of the appliance. It is imperative that these instructions are observed.
Contents CONTENTS Operating Instructions .................................... 5 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Economical and Ecological Dishwashing . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Appliance Features and Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents What to do, if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...there are problems with the operation of the dishwasher. . . . . . . . . . . . ...the wash result is not satisfactory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 30 32 32 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions OPERATING INSTRUCTIONS 1 Safety Instructions The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law. Nevertheless, as a manufacturer we consider it our obligation to make you aware of the following safety information: Installation, Connection and Placing into Operation • The dishwasher may only be transported upright. • Check the dishwasher for transport damage.
Operating Instructions • Never place the dishwasher in operation if the mains cable, water inlet or drain hose is damaged; or the control panel, work top or plinth area is damaged such that the inside of the appliance is freely accessible. • If the mains lead is damaged, or is to be replaced for a longer lead, the cable (obtainable from AEG Service Force) must be changed by a service engineer authorised by AEG. • Never unplug the appliance by pulling on the cable, always pull the plug.
Operating Instructions • In the event of a fault, first close the tap, then switch off the appliance and unplug it from the mains. If the appliance is permanently wired to the mains: remove the fuse. 2 Disposal Disposing of the Packaging Material Dispose of the dishwasher packaging material correctly. All the packaging materials used are harmless to the environment and can be recycled. • Plastic parts are marked with standard international abbreviations: – >PE< for polyethylene, e.g.
Operating Instructions 2 Economical and Ecological Dishwashing • Ensure that the water softener is correctly adjusted. • Do not pre-rinse dishes under running water. • If you wash a small load, the load sensor calculates the amount of water necessary and shortens the programme. It is more economical to always wash with a full load. • Select the wash programme to suit the nature and degree of the soiling on the dishes.
Operating Instructions Appliance Features and Control Panel Top Spray Arm Rubber Seal for Connecting the Water Feed to the Middle Spray Arm Spray Arms Container for Salt Container for Rinse Aid Container for Detergent Inlet for Fan Assisted Drying Rating Plate Filters Interior Lighting 9
Operating Instructions Control Panel Signal Tone Button Water Softener Button Control Panel Door Handle MultiDisplay Air Outlet for Fan Assisted Drying Set Start Delay Indicators Display for the Individual Wash Programme Steps The Control Panel comprises the ON/OFF switch and the programme buttons with LED indicators.
Operating Instructions Prior to using for the first time Prior to using for the first time, remove all the clips with which the dish racks are secured for transport. Then perform the following steps: 0 1. Adjust the water softener 2. Fill with Salt for the Water Softener 3. Fill with Rinse Aid Adjust the Water Softener To prevent the build up of scale on dishes and in the dishwasher, the dishes must be washed with soft, i.e. low lime content water.
Operating Instructions 0 1. The dishwasher must be switched off. 2. Press the signal tone and water softener buttons simultaneously and keep them pressed 3. Press the ON/OFF button. The LED indicators for the signal tone and water softener buttons flash. 4. Press the softener button again. The multi-display indicates the hardness setting. 5. Pressing the hardness button increases the hardness setting by 1. (Exception: Hardness setting 0 follows hardness setting 9). 6.
Operating Instructions 3 The water expelled by filling the salt container with special salt runs out of the salt container onto the base of the washing compartment. This is not a cause for concern, the water will be pumped out at the start of the next wash programme. 5. Clean any salt remnants on the container opening. 6. Turn the lid clockwise to the stop, otherwise dishwasher salt will leak into the wash water, this could lead to poor wash results.
Operating Instructions Filling with Rinse Aid Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, spot and streak free drying. 1 Only use rinse aid specifically designed for domestic dishwashers. Never fill the rinse aid container with any other substance as this would damage the appliance. Fill with rinse aid: – Prior to using the dishwasher for the first time – When the RINSE AID indicator on the control panel is illuminated.
Operating Instructions Adjusting Rinse Aid Dosing 3 As the dishes are washed rinse aid is released from the dispenser into the wash water. The dose is factory set at 4, and can be adjusted from 1 to 6. Only change the setting if streaks, milky spots or dried on water marks are visible on glasses or crockery. 0 1. Open the door of the dishwasher. 2. Press the rinse aid compartment release button with your finger. 3. Fully open the rinse aid compartment lid. 4. Set the dose level. 5.
Operating Instructions In Daily Use • Check the salt and rinse aid levels. • Load cutlery and dishes into the dishwasher • Fill with dishwasher detergent • Select a wash programme suitable for the cutlery and dishes • Start the wash programme Loading Cutlery and Dishes 1 Sponges, household cloths and any object that can absorb water should not be washed in the dishwasher.
Operating Instructions – To avoid damage to glasses, they must not touch – Do not lay small objects (e.g. lids) in the cutlery rack Loading Cutlery 1 1 Long bladed knives stored in an upright position are a potential hazard. 1 Take care when loading or unloading sharp items such as knives. Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Place knives, small spoons and small forks in the cutlery tray.
Operating Instructions If you use the grid insert, it is not possible to open the cutlery basket. To ensure that the cutlery basket cannot open on removal from the appliance, you should always hold both parts of the two part handle. 0 1. Place the cutlery basket on a table or work surface 2. Open the two part handle 3. Remove cutlery 4. Close the two part handle.
Operating Instructions Loading Pans, Frying Pans and Large Plates Load large and heavily soiled dishes in the lower rack. To ease the loading of large items at some dishwasher-models the two rows of prongs for the right-hand plate insert can be folded down: 0 1. Slightly lift the right plate insert. 3 2. Fold the plate insert to the left.
Operating Instructions Loading Cups, Glasses and Coffee Services Load small, delicate items and long pointed cutlery in the upper rack. • Arrange items of crockery on the folding cups racks so that they are offset from each other and water can reach all items. • The cup racks can be folded up out of the way for tall items. • Lay or hang wine, champagne, and brandy glasses in the cut outs on the cup racks. • Glasses, beakers, etc. can also be placed on the two rows of prongs on the left of the upper rack.
Operating Instructions Adjusting the Height of the Upper Basket Maximum Height of the Dishes in the Upper Basket Lower Basket 3 With upper basket raised 22 cm 31 cm With upper basket lowered 24 cm 29 cm The height of the basket can also be adjusted when it is loaded. Depending on the model, your appliance is provided with one of the following types of upper basket: Lowering the Upper Basket: 0 1. Pull the upper basket out completely. 2. Lift the upper basket at the rear right and lower.
Operating Instructions Filling with Detergent 1 Only use dishwasher detergent. Fill with detergent: – Prior to the start of a wash programme (not for the pre wash programme). The detergent is released into the wash water during the programme. Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging. The detergent compartment is on the inside of the dishwasher door. 0 1. If the lid is closed: press release button (1). The lid springs open. 2 2.
Operating Instructions Bio Wash Programmes and Concentrated Detergents Based on their chemical composition, dishwasher detergents can be split into two basic types: – Conventional, alkaline detergents with caustic components – Weak alkaline concentrated detergents with natural enzymes.
Operating Instructions Selecting the Wash Programme (Programme Table) Choose the most suitable wash programme with the aid of this table: Type of Dishes Dinner Service and Cooking Utensils In Addition - Type of Soiling Suitable Wash Programme: Programme Sequence 2) Consumption Figures: 3) • normally to lightly soiled particularly suited to the use of concentrated detergents.
Operating Instructions Type of Dishes Dinner Service and Cooking Utensils Dessert Dishes and Coffee Service All Types of Dishes with non-temperature resistant dishes with delicate glasses - In Addition Type of Soiling • normally soiled • lightly soiled particularly suited to the use of concentrated detergents.
Operating Instructions Starting the Wash Programme 0 1. Check that when the dishes and cutlery are loaded into the dishwasher the spray arms are free to rotate. 2. Open the tap fully. 3. Shut the door. 4. Press the ON/OFF button The ON/OFF button indicator illuminates. 5. Press the button for the programme required (see “Programme Table“). The programme indicator and the associated wash programme steps in the programme progress display illuminate.
Operating Instructions 0 1. Open the door of the dishwasher. The wash programme stops. 2. Shut the door. The wash programme continues. Cancelling the wash programme 0 1. Press the button for the wash programme in progress and keep it pressed. The programme indicator for the wash programme in progress flashes for a few seconds and then goes out. 2. Release the programme button, the wash programme is stopped.
Operating Instructions Load Sensing – Sensor Logic If a wash programme is started even though there are only a few dishes in the upper and/or lower rack, an intelligent electronic system adjusts the amount of water and the duration of the wash programme to the number of dishes. By this means it is possible to wash only a few dishes quickly and economically. At half load (6 place settings), up to 2 litres of water and 0.2 kWh of electricity are saved.
Operating Instructions Care and Cleaning 1 Do not under any circumstances use furniture care products or aggressive cleaners. • If necessary, clean the controls only with a soft cloth and pure warm water. • The spray arms do not need cleaning. • Occasionally check the internal containers, door seal, and water inlet for soiling, clean if necessary. Cleaning the Filter The filters should be checked and cleaned regularly. Dirty filters will give poor wash results. 0 1. Open the door, remove the lower rack.
Operating Instructions 7. Put the flat filter back in the base of the washing compartment 8. Place the coarse/fine filter in the microfilter and press together. 9. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment. 1 The dishwasher must not be used without filters under any circumstances. What to do, if ...
Operating Instructions • For all other faults that are indicated, please contact AEG Service Force stating the fault code. Symptom Possible Cause Solution The programme indicator for the programme selected is flashing, the WATER indicator is illuminated and 1 warning tone can be heard that is continually repeated: no water is running into the dishwasher. Tap is blocked or furred with lime-scale. The water inlet hose is not correctly laid. Check hose installation.
Operating Instructions ...there are problems with the operation of the dishwasher. Symptom Possible Cause Solution The door of the dishwasher is Shut the door. not closed properly. Mains plug is not plugged in. Insert mains plug. The programme does not start. House fuse in defective. Replace fuse. A delay start is selected. If the dishes are to be washed immediately, set the delay start to 0 hours The washing compartment is made of corrosion-resistant stainless steel.
Operating Instructions The dishes are wet and dull. – Rinse aid was not used. – The rinse aid container is empty. There are streaks, milky spots or a bluish coating on glasses and dishes. – Decrease rinse aid dosing. There are dried water drops on the glasses and dishes. – Increase rinse aid dosing. – The detergent may be the cause. Contact the detergent manufacturer's consumer advisor.
Operating Instructions Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme (see Programme Table). Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see Programme Table). 34 Full Load: 12 place settings incl. serving dishes Half Load: 6 place settings incl.
Installation and Connection Instructions INSTALLATION AND CONNECTION INSTRUCTIONS Installing the Dishwasher • The dishwasher must be installed on a firm floor and adjusted such that it is stable and level. • To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units extend the threaded feet by unscrewing: – use a screwdriver.
Installation and Connection Instructions • If the dishwasher is installed underneath a kitchen work surface, the original work surface of the dishwasher is to be removed as follows: – Unscrew the screws (1) from the elbows on the back side. – Slide the work surface approx. 1cm to the rear (3) , lift at the front (4) and remove. – Press the work surface retaining brackets at the position shown in the diagram (4) and remove the bracket at an angle to the rear (5).
Installation and Connection Instructions Connecting the Dishwasher Water Connection The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations. • The dishwasher can be connected to cold and hot water supplies up to max. 60 °C. • The dishwasher must not be connected to open hot water appliances or instantaneous water heaters.
Installation and Connection Instructions Water drain Drain hose 1 The drain hose must not be kinked, crushed or entangled. • Connecting the drain hose: – Maximum permitted height: 1 metre. – Minimum required height 30 cm above the lower edge of the machine. Extension hoses • Extension hoses are available from AEG Service Force. The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded.
Installation and Connection Instructions Leak Prevention System For protection from damage due to water leaks, the dishwasher is equipped with a leak prevention system, the AQUA CONTROL SYSTEM. In the event of a fault, the safety valve immediately interrupts the supply of water to the appliance and the drain pump switches on. It is thus not possible for water to either leak or overflow. Any water left in the appliance is automatically pumped out.
Installation and Connection Instructions Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. 1 WARNING - This appliance must be earthed. The manufacturer declines any responsibility should these safety measures not be observed. Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. To isolate the dishwasher from the mains, remove the mains plug.
Installation and Connection Instructions Connections The water inlet and drain hoses, as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the appliance. The plumbing and electrical installation example given below can only be regarded as a recommendation.
Guarantee Conditions GUARANTEE CONDITIONS 1. 2. 3. 4. 5. 6. Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials.
Service and Spare parts SERVICE AND SPARE PARTS In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact Service Force by telephoning: 08705 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the adress of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.