EN PL User Manual Dishwasher Instrukcja obsługi Zmywarka 2 20 FAVORIT53612WO FAVORIT53612MO
www.aeg.com CONTENTS 1. SAFETY INFORMATION...........................................................................................3 2. SAFETY INSTRUCTIONS.......................................................................................... 4 3. PRODUCT DESCRIPTION........................................................................................ 6 4. CONTROL PANEL ....................................................................................................7 5. PROGRAMMES.............
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com 1.2 Children and vulnerable people safety • • • • • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Do not let children play with the appliance. Keep all detergents away from children.
ENGLISH 5 • The appliance can release hot steam if you open the door while a programme operates. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. 2.5 Service WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous.
www.aeg.com 3.
ENGLISH 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Start button 7 Indicators 8 Option button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Drying phase. It comes on when the drying phase operates. Multitab indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates. TimeSaver indicator.
www.aeg.com 5.
ENGLISH Programme 1) Water (l) Energy (kWh) Duration (min) 9 0.9 30 4 0.1 14 9 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes info.test@dishwasher-production.com For all the necessary information for test performance, send an email to: Write down the product number (PNC) that is on the rating plate. 6. SETTINGS 6.
www.aeg.com German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level.
ENGLISH – = rinse aid dispenser deactivated. 3. Press Option to change the setting. 4. Press the on/off button to confirm the setting. until the indicators There is also an acoustic signal that sounds when the programme is completed. By default this acoustic signal is deactivated but it is possible to activate it. , and start to flash and the display is blank. 2. Press Delay • The indicators 6.4 Acoustic signals Acoustic signals sound when a malfunction of the appliance occurs.
www.aeg.com The washing results are the same as with the normal programme duration. The drying results can decrease. How to activate TimeSaver Press Option until the indicator comes on. If the option is not applicable to the programme, the related indicator does not come on or it flashes quickly for a few seconds and then goes off. The display shows the updated programme duration. 8. BEFORE FIRST USE 1.
ENGLISH 8.2 How to fill the rinse aid dispenser A D B C M AX 4 1. Press the release button (D) to open the lid (C). 2. Pour the rinse aid in the dispenser (A) until the liquid reaches the fill level 'max'. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the release button locks into position. 1 3 2 + CAUTION! Only use rinse aid specifically designed for dishwashers.
www.aeg.com A 30 B • The programme duration starts to decrease with steps of 1 minute. D Starting a programme with delay start 20 C 1. Press the release button (B) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (A). 3. If the programme has a prewash phase, put a small quantity of detergent in the compartment (D). 4. Close the lid. Make sure that the release button locks into position. 9.
ENGLISH End of the programme When the programme is completed the display shows 0:00. The phase indicators are off. All buttons are inactive except for the on/off button. 15 automatically deactivate the appliance. If you open the door before the activation of Auto Off, the appliance is automatically deactivated. 2. Close the water tap. 1. Press the on/off button or wait for the Auto Off function to 10. HINTS AND TIPS 10.
www.aeg.com 10.4 Loading the baskets • Only use the appliance to wash items that are dishwasher-safe. • Do not put in the appliance items made of wood, horn, aluminium, pewter and copper. • Do not put in the appliance items that can absorb water (sponges, household cloths). • Remove larger residues of food from the dishes into the waste bin. • Make soft the remaining burned food on the items. • Put hollow items (cups, glasses and pans) with the opening down.
ENGLISH 17 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 4. Wash the filters. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.
www.aeg.com • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance. To prevent this, we recommend to run long duration programmes at least 2 times per month. 12. TROUBLESHOOTING If the appliance does not start or it stops during operation. Before you contact an Authorised Service Centre, check if you can solve the problem by yourself with the help of the information in the table. With some problems, the display shows an alarm code.
ENGLISH 19 12.1 The washing and drying results are not satisfactory Problem Possible solution There are whitish streaks or bluish layers on glasses and dishes. • The release quantity of rinse aid is too much. Adjust the rinse aid selector to a lower position. • The quantity of detergent is too much. There are stains and dry water drops on glasses and dishes. • The released quantity of rinse aid is not sufficient. Adjust the rinse aid selector to a higher position.
www.aeg.com SPIS TREŚCI 1. INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA......................................... 21 2. WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA.......................................... 22 3. OPIS URZĄDZENIA......................................................................................... 24 4. PANEL STEROWANIA ....................................................................................25 5. PROGRAMY........................................................................................
POLSKI 1. 21 INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA Przed instalacją i rozpoczęciem eksploatacji urządzenia należy uważnie zapoznać się z załączoną instrukcją obsługi. Producent nie odpowiada za uszkodzenia i obrażenia ciała spowodowane nieprawidłową instalacją i eksploatacją. Należy zachować instrukcję wraz z urządzeniem do wykorzystania w przyszłości. 1.
www.aeg.com • • Wykładzina podłogowa nie może zasłaniać otworów wentylacyjnych w podstawie (jeśli dotyczy). Urządzenie należy podłączyć do instalacji wodociągowej za pomocą nowego zestawu węży dostarczonych w komplecie z urządzeniem. Nie wolno używać starego zestawu węży. 1.
POLSKI • • • • • • • przeciwnym razie należy skontaktować się z elektrykiem. Należy używać wyłącznie prawidłowo zamontowanego gniazda elektrycznego z uziemieniem. Nie stosować rozgałęźników ani przedłużaczy. Należy zwrócić uwagę, aby nie uszkodzić wtyczki ani przewodu zasilającego. Wymiany przewodu zasilającego można dokonać wyłącznie w naszym autoryzowanym centrum serwisowym. Podłączyć wtyczkę do gniazda elektrycznego dopiero po zakończeniu instalacji.
www.aeg.com • Numer produktu: Numer seryjny: • • 2.6 Utylizacja OSTRZEŻENIE! Występuje zagrożenie odniesieniem obrażeń ciała lub uduszeniem. Odłączyć urządzenie od źródła zasilania. Odciąć i wyrzucić przewód zasilający. Wymontować zatrzask drzwi, aby uniemożliwić zamknięcie się dzieci lub zwierząt w urządzeniu. 3.
POLSKI 4. PANEL STEROWANIA 1 2 8 1 2 3 4 5 3 4 7 Przycisk wł./wył. Przycisk Program Wskaźniki programów Wyświetlacz Przycisk Delay 5 6 6 Przycisk Start 7 Wskaźniki 8 Przycisk Option 4.1 Wskaźniki Wskaźnik Opis Faza zmywania. Włącza się podczas fazy zmywania. Faza suszenia. Zapala się podczas fazy suszenia. Wskaźnik funkcji Multitab. Wskaźnik soli. W trakcie programu wskaźnik ten jest zawsze wyłączony. Wskaźnik płynu nabłyszczającego. W trakcie programu wskaźnik ten jest zawsze wyłączony.
www.aeg.com 5.
POLSKI 27 5.1 Parametry eksploatacyjne Program1) Zużycie wody (l) Zużycie energii (kWh) Czas trwania (min) 9.9 0.932 195 7 - 12 0.6 - 1.4 40 - 150 13 - 15 1.3 - 1.5 140 - 160 8-9 1.0 - 1.2 55 - 65 9 0.9 30 4 0.1 14 1) Parametry eksploatacyjne mogą ulec zmianie w zależności od ciśnienia i temperatury wody, zmian w napięciu zasilania, użytych opcji oraz ilości naczyń. 5.
www.aeg.com Im wyższa zawartość substancji mineralnych, tym twardsza jest woda. Twardość wody jest mierzona w równoważnych skalach. doprowadzonej do urządzenia. W lokalnym zakładzie wodociągowym można uzyskać informację na temat twardości wody. Istotne jest ustawienie właściwego poziomu zmiękczania wody, aby zapewnić dobre rezultaty zmywania.
POLSKI Stosowanie płynu nabłyszczającego i tabletek wieloskładnikowych Gdy włączona jest opcja Multitab, dozownik płynu nabłyszczającego w dalszym ciągu dawkuje płyn. Można jednak wyłączyć dozownik płynu nabłyszczającego. W tym przypadku efekty suszenia mogą nie być zadowalające. Wyłączanie dozownika płynu nabłyszczającego Urządzenie musi być w trybie wyboru programów. 1. Aby uruchomić tryb użytkownika, należy nacisnąć jednocześnie i przytrzymać przyciski Delay i Start, , i , a wyświetlacz będzie pusty.
www.aeg.com Nie wszystkie opcje są ze sobą zgodne. Po wybraniu niezgodnych ze sobą opcji urządzenie automatycznie wyłączy jedną lub większą liczbę opcji. Tylko wskaźniki aktywnych opcji pozostaną wówczas włączone. 7.1 Multitab Włączyć tę opcję w przypadku stosowania tabletek wieloskładnikowych z solą, płynem nabłyszczającym i detergentem. Mogą one zawierać także inne środki do mycia lub płukania. Opcja ta powoduje wyłączenie dozowania soli. Nie włącza się wskaźnik soli.
POLSKI Napełnianie zbiornika soli 1. Obrócić pokrywkę zbiornika soli w lewo i ją zdjąć. 2. Wlać 1 litr wody do zbiornika soli (tylko za pierwszym razem). 3. Napełnić zbiornik soli solą do zmywarek. 31 8.2 Napełnianie dozownika płynu nabłyszczającego A D B C B A 4. Usunąć sól rozsypaną wokół otworu zbiornika soli. M AX 4 1 3 2 + - C D 5. Obrócić pokrywkę zbiornika soli w prawo, aby zamknąć zbiornik soli. Podczas napełniania zbiornika soli może się z niego wydostawać woda i sól.
www.aeg.com 9. CODZIENNA EKSPLOATACJA 1. Odkręcić zawór wody. 2. Nacisnąć przycisk wł./wył., aby włączyć urządzenie. Upewnić się, że urządzenie jest w trybie wyboru programów. • Jeśli świeci się wskaźnik soli, napełnić zbiornik soli. • Jeśli świeci się wskaźnik płynu nabłyszczającego, napełnić dozownik płynu nabłyszczającego. 3. Załadować kosze. 4. Dodać detergent. Aby stosować tabletki wieloskładnikowe, należy włączyć funkcję Multitab. 5.
POLSKI Wyświetlacz wyświetli czas trwania programu. 4. Ustawić odpowiednie opcje. 5. Nacisnąć Start, aby uruchomić program. • Włączy się wskaźnik fazy zmywania. • Czas trwania programu będzie odliczany skokowo co 1 minutę. Uruchamianie programu z opóźnieniem 1. Ustawić program. 2. Nacisnąć kilkakrotnie Delay, aż na wyświetlaczu pojawi się żądany czas opóźnienia (od 1 do 24 godzin). Wskaźnik wybranego programu miga. 3. Nacisnąć Start. 4. Zamknąć drzwi urządzenia, aby uruchomić odliczanie.
www.aeg.com • jednym”). Przestrzegać informacji podanych na opakowaniu. Ustawić odpowiedni program dla określonego rodzaju naczyń i poziomu zabrudzenia. W programie ECO uzyskuje się największą efektywność zużycia wody i energii elektrycznej podczas zmywania średnio zabrudzonych naczyń i sztućców. 10.2 Stosowanie soli, płynu nabłyszczającego i detergentu • • • • • Należy stosować wyłącznie sól, płyn nabłyszczający i detergent do zmywarek. Inne produkty mogą uszkodzić urządzenie.
POLSKI • • • • • pokrywka zbiornika soli nie jest poluzowana; ramiona spryskujące są drożne; w zmywarce znajduje się sól do zmywarek i płyn nabłyszczający (chyba że stosowane są wieloskładnikowe tabletki z detergentem); ułożenie naczyń i przyborów kuchennych w koszach jest prawidłowe; program jest odpowiedni dla danego rodzaju załadunku i stopnia zabrudzenia; • użyto prawidłową ilość detergentu. 10.6 Opróżnianie koszy 1. Przed wyjęciem naczyń ze zmywarki poczekać, aż wystygną.
www.aeg.com UWAGA! Nieprawidłowe umiejscowienie filtrów może skutkować niezadowalającymi efektami zmywania i uszkodzeniem urządzenia. 11.2 Czyszczenie ramion spryskujących 5. Upewnić się, że wokół krawędzi osadnika nie znajdują się resztki żywności ani zanieczyszczenia. 6. Włożyć na miejsce filtr (A). Upewnić się, że jest prawidłowo umieszczony pod 2 prowadnicami. Nie wolno wyjmować ramion spryskujących.
POLSKI 37 12. ROZWIĄZYWANIE PROBLEMÓW Jeśli urządzenie nie daje się uruchomić lub przestaje działać podczas pracy. Przed skontaktowaniem się z autoryzowanym centrum serwisowym należy sprawdzić, czy problem można rozwiązać samodzielnie, korzystając z informacji zawartych w tabeli. Przy niektórych usterkach na wyświetlaczu pojawia się kod alarmowy. Problem i kod alarmowy Możliwe rozwiązanie Urządzenie nie włącza się. • • Program nie uruchamia się. • • • • Urządzenie nie napełnia się • wodą.
www.aeg.com 12.1 Efekty zmywania i suszenia są niezadowalające Problem Możliwe rozwiązanie Białawe smugi lub niebieska‐ wy nalot na szklankach i nac‐ zyniach. • • Za dużo płynu nabłyszczającego. Obrócić pokrętło regulacji dozowania płynu nabłyszczającego, aby zmniejszyć dozowanie. Użyto za dużo detergentu. Plamy i ślady po odparowa‐ • nych kroplach wody na szklan‐ kach i naczyniach. • Za mało płynu nabłyszczającego.
POLSKI 39 14. OCHRONA ŚRODOWISKA ludzkie zdrowie. Nie wolno wyrzucać Materiały oznaczone symbolem należy poddać utylizacji. Opakowanie urządzenia włożyć do odpowiedniego pojemnika w celu przeprowadzenia recyklingu. Należy zadbać o ponowne przetwarzanie odpadów urządzeń elektrycznych i elektronicznych, aby chronić środowisko naturalne oraz urządzeń oznaczonych symbolem razem z odpadami domowymi.
156981370-A-272014 www.aeg.