FEE62600PM NL EN FR USER MANUAL Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 25 46
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE......................................................................................... 2 2. VEILIGHEIDSVOORSCHRIFTEN.................................................................................4 3. BESCHRIJVING VAN HET PRODUCT........................................................................6 4. BEDIENINGSPANEEL................................................................................................. 7 5. PROGRAMMA’S..................
NEDERLANDS 3 niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen onder druk en/of stoom om het apparaat te reinigen.
NEDERLANDS 2.3 Aansluiting aan de waterleiding • Beschadig de waterslangen niet. • Indien buizen lang niet zijn gebruikt, er reparaties hebben plaatsgevonden of er nieuwe apparaten zijn geplaatst (watermeters, enz.), moet u, voordat de nieuwe buizen worden aangesloten, het water laten stromen tot het schoon en helder is. • Zorg ervoor dat er geen zichtbare waterlekken zijn tijdens en na het eerste gebruik van het apparaat.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 3 8 1 2 3 4 5 Aan/uit-toets Program-toets Programma-indicatielampjes Weergave Delay-toets 4 7 5 6 6 Option-toets 7 Indicatielampjes 8 Start-toets 4.1 Indicatielampjes Aanduiding Beschrijving Wasfase. Gaat aan wanneer de wasfase en de spoelfases in werking zijn. Spoelfase. Gaat aan wanneer de spoelfase loopt. Droogfase. Gaat aan wanneer de droogfase loopt. Einde-indicatielampje. TimeSaver-indicatielampje. XtraDry-indicatielampje. Glansmiddelindicatielampje.
www.aeg.com Aanduiding Beschrijving ExtraHygiene-indicatielampje. 5.
NEDERLANDS 9 5.1 Verbruikswaarden Programma 1) Water (l) Energie (kWh) Bereidingsduur (min) 10.5 0.932 225 7 - 14 0.6 - 1.6 40 - 170 12.5-14.5 1.4-1.7 170-190 12 - 14 0.7 - 0.9 82-92 10 0.9 30 9 - 10 1.1 - 1.3 230 - 250 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.
www.aeg.com waterhardheid wordt gemeten in de volgende gelijkwaardige schalen. De waterontharder moet worden afgesteld op de hardheid van het water in uw woonplaats. Uw waterleidingbedrijf kan u informeren over de hardheid van het water in uw woonplaats. Het is belangrijk om het correcte niveau voor de waterontharder in te stellen voor goede wasresultaten. Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.
NEDERLANDS (hoogste hoeveelheid). Niveau 0 schakelt het glansmiddeldoseerbakje uit en er wordt geen glansmiddel afgegeven. Fabrieksinstelling: stand 4. Het apparaat moet in de programmakeuzemodus staan. Het apparaat moet in de programmakeuzemodus staan. 1. Houd om de gebruikersmodus in te voeren tegelijkertijd Delay en Option ingedrukt tot de , , en gaan knipperen en het display blanco is. 2. Druk op Delay. • De indicatielampjes uit.
www.aeg.com Tijdens de werking van de droogfase, wordt de deur van het apparaat door een instrument geopend. De deur blijft op een kier. LET OP! Probeer de deur van het apparaat niet binnen 2 minuten na automatisch openen te sluiten. Dit kan het apparaat beschadigen. Gebruik om de droogresultaten te verbeteren de optie XtraDry of activeer AirDry. Het deactiveren van AirDry Het apparaat moet in de programmakeuzemodus staan. 1.
NEDERLANDS Met deze optie verhoogt u de druk en de temperatuur van het water. De wasen droogfasen zijn korter. TimeSaver is standaard uitgeschakeld, maar kan handmatig worden geactiveerd. Deze optie kan niet op hetzelfde moment met XtraDry worden gecombineerd. TimeSaver activeren Druk op Option totdat het indicatielampje aan gaat. Als de optie niet van toepassing is op het programma, dan gaat het bijbehorende indicatielampje niet branden of het knippert even en gaat dan uit.
www.aeg.com LET OP! Gebruik alleen glansmiddel voor afwasautomaten. 5. Draai de dop van het zoutreservoir rechtsom om het zoutreservoir te sluiten. LET OP! Water en zout kunnen uit het zoutreservoir stromen als u het bijvult. Start na het bijvullen van het zoutreservoir onmiddellijk een programma om corrosie te voorkomen. 8.2 Het vullen van het glansmiddeldoseerbakje A B 1. Open het deksel (C). 2. Vul het glansmiddeldoseerbakje (B) niet verder dan de aanduiding ''MAX''. 3.
NEDERLANDS 9.1 Vaatwasmiddel gebruiken A B C LET OP! Gebruik uitsluitend vaatwasmiddelen die specifiek zijn bedoeld voor gebruik in vaatwassers 1. Druk op de ontgrendelknop (A) om de deksel te openen (C). 2. Doe de vaatwastablet of het poeder in het doseerbakje (B). 3. Plaats een kleine hoeveelheid van het vaatwasmiddel in de binnenkant van de deur van het apparaat als het programma een voorwasfase heeft. 4. Sluit het deksel. Zorg ervoor dat de deksel op zijn plaats dichtklikt. 9.
www.aeg.com LET OP! Probeer de deur van het apparaat niet binnen 2 minuten nadat AirDry hem automatisch opent te openen, want dit kan schade aan het apparaat veroorzaken. Als hierna de deur gedurende nog 3 minuten wordt gesloten, beëindigt het draaiende programma. De uitgestelde start annuleren tijdens het aftellen Als u de uitgestelde start annuleert, moet u het programma en de opties opnieuw instellen. Houd tegelijkertijd Delay en Option ingedrukt tot het apparaat in de programmakeuzemodus staat.
NEDERLANDS instructies van de vaatwasmiddelfabrikant. 10.3 Wat moet u doen als u wilt stoppen met het gebruik van multitabletten Doe het volgende voordat u begint met het gebruiken van apart wasmiddel, zout en glansmiddel. 1. Stel het hoogste niveau van de waterontharder in. 2. Zorg ervoor dat het zout- en het glansmiddeldoseerbakje gevuld zijn. 3. Start het kortste programma met een spoelfase. Voeg geen afwasmiddel toe en ruim de mandjes niet in. 4.
www.aeg.com 11.1 De filters reinigen Het filtersystem bestaat uit 3 delen. C B A 1. Draai de filter (B) linksom en verwijder het. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter (A) terug. Zorg ervoor dat het goed onder de 2 geleidingen zit. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3.
NEDERLANDS 11.2 De bovenste sproeiarm schoonmaken We raden u aan om de bovenste sproeiarm regelmatig schoon te maken om te voorkomen dat vuil de gaten verstopt. 19 naar boven in de richting van de lagere pijl en draait u hem tegelijkertijd tegen de wijzers van de klok in, zodat hij op zijn plek vergrendelt. Verstopte gaten kunnen onbevredigende wasresultaten opleveren. 1. Trek het bovenrek naar buiten. 2.
www.aeg.com WAARSCHUWING! Niet juist uitgevoerde reparaties kunnen de veiligheid van de gebruiker ernstig in gevaar brengen. Alle reparaties moeten worden uitgevoerd door bevoegd personeel. Bij sommige problemen wordt er op de display een alarmcode weergegeven. Het merendeel van de problemen die ontstaan kunnen worden opgelost zonder contact op te nemen met een erkend servicecentrum. Probleem en alarmcode Mogelijke oorzaak en oplossing U kunt het apparaat niet activeren.
NEDERLANDS Probleem en alarmcode Mogelijke oorzaak en oplossing De resterende duur in het display wordt verlengd en schakelt bijna naar het eind van de programmaduur. • Dit is geen storing. Het apparaat werkt goed. Kleine lekkage uit de deur van het apparaat. • Het apparaat staat niet waterpas. Draai aan de verstelbare pootjes (indien van toepassing). • De deur van het apparaat is niet gecentreerd op de kuip. Verstel de achterpoot (indien van toepassing). De deur van het apparaat sluit moeilijk.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Slechte droogresultaten. • Serviesgoed heeft te lang in het gesloten apparaat gestaan. • Het glansmiddel is op of de dosering van glansmiddel is niet voldoende. Stel de dosering van het glansmiddel in op een hogere stand. • Plastic voorwerpen moeten mogelijk met een doek worden afgedroogd. • Activeer voor de beste droogprestatie de optie XtraDry en stel AirDry in. • We raden aan altijd glansmiddel te gebruiken, zelfs in combinatie met wastabletten.
NEDERLANDS Probleem 23 Mogelijke oorzaak en oplossing Er bevinden zich aan het einde • De vaatwastablet raakte klem in het vaatwasmiddeldovan het programma resten van seerbakje en is daardoor niet volledig weggespoeld vaatwasmiddel in het vaatwasdoor het water. middeldoseerbakje. • Het water kan het vaatwasmiddel niet uit het vaatwasmiddeldoseerbakje spoelen. Zorg ervoor dat de bovenste sproeiarm niet geblokkeerd of verstopt is.
www.aeg.com Energieverbruik Modus aan laten (W) 5.0 Energieverbruik Uit-modus (W) 0.10 1) Zie het typeplaatje voor andere waarden. 2) Als het hete water door een alternatieve, milieuvriendelijkere energiebron geproduceerd wordt (bijv. zonnepanelen en windenergie), gebruik dan een heetwatervoorziening om het energieverbruik te verminderen. 14. MILIEUBESCHERMING Recycle de materialen met het symbool . Gooi de verpakking in een geschikte verzamelcontainer om het te recyclen.
ENGLISH 25 CONTENTS 1. SAFETY INFORMATION........................................................................................... 25 2. SAFETY INSTRUCTIONS...........................................................................................27 3. PRODUCT DESCRIPTION.........................................................................................28 4. CONTROL PANEL..................................................................................................... 29 5. PROGRAMMES..........
www.aeg.com manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
ENGLISH • • • • • 27 Do not keep the appliance door open without supervision to prevent to fall on it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. 2.
www.aeg.com WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance.
ENGLISH 5 6 7 8 9 Rating plate Salt container Air vent Rinse aid dispenser Detergent dispenser 29 10 Cutlery basket 11 Lower basket 12 Upper basket 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase and the rinsing phases operate. Rinsing phase. It comes on when the rinsing phase operates.
www.aeg.com Indicator Description XtraDry indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. Delay indicator. ExtraHygiene indicator. 5.
ENGLISH Programme 4) Degree of soil Type of load Programme phases • Normal soil • Prewash • Crockery and cut- • Wash 50 °C lery • Rinses • Dry 31 Options • XtraDry 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets .
www.aeg.com 6.2 The water softener These settings will be saved until you change them again. The water softener removes minerals from the water supply, which would have a detrimental effect on the washing results and on the appliance. How to set the programme selection mode The appliance is in programme selection mode when the programme indicator The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales.
ENGLISH , and start to flash and the display is blank. 2. Press Program. • The indicators , and go off. continues to • The indicator flash. • The display shows the current setting: e.g. = level 5. 3. Press Program again and again to change the setting. 4. Press the on/off button to confirm the setting. 6.3 The rinse aid dispenser The rinse aid is automatically released during the hot rinse phase.
www.aeg.com How to deactivate AirDry The appliance must be in programme selection mode. 1. To enter the user mode, press and hold simultaneously Delay and Option until the indicators , , and start to flash and the display is blank. 2. Press Option. • The indicators While the drying phase operates, a device opens the appliance door. The door is then kept ajar. CAUTION! Do not try to close the appliance door within 2 minutes after automatic open. This can cause damage to the appliance. and , go off.
ENGLISH 7.2 TimeSaver The TimeSaver allows to reduce the time of the selected programme. The total programme duration decreases by approximately 50%. The washing results are the same as with the normal programme duration. The drying results can decrease. This option increases the pressure and the temperature of the water. The washing and the drying phases are shorter. By default, TimeSaver is off, but it is possible to activate it manually. This option cannot be combined with XtraDry at the same time.
www.aeg.com CAUTION! Only use rinse aid specifically designed for dishwashers. 5. Turn the cap of the salt container clockwise to close the salt container. CAUTION! Water and salt can come out of the salt container when you fill it. After you fill the salt container, immediately start a programme to prevent corrosion. 8.2 How to fill the rinse aid dispenser A B C 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance.
ENGLISH 9.1 Using the detergent A B C 37 2. Press Program again and again until the indicator of the programme you want to select comes on. The display shows the programme duration. 3. Set the applicable options. 4. Press Start to start the programme. • The indicator of the running phase comes on. • The programme duration starts to decrease with steps of 1 minute. Starting a programme with delay start 1. Press the release button (A) to open the lid (C). 2.
www.aeg.com CAUTION! Do not try to close the appliance door within 2 minutes after AirDry automatically opens it, as this may cause damage to the appliance. If, afterwards, the door is closed for another 3 minutes, the running programme ends. Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again. Make sure that there is detergent in the detergent dispenser before you start a new programme.
ENGLISH detergent residues on the tableware, we recommend that you use the tablets with long programmes. • Do not use more than the correct quantity of detergent. Refer to the instructions on the detergent packaging. 10.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3.
www.aeg.com 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 1. Turn the filter (B) counterclockwise and remove it. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B).
ENGLISH 11.2 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. 41 4. To engage again the spray arm to the basket, press the spray arm upwards in the direction indicated by the lower arrow and simultaneously turn it counterclockwise until it locks into place. Clogged holes can cause unsatisfactory washing results. 1. Pull out the upper basket. 2.
www.aeg.com With some problems, the display shows an alarm code. to contact an Authorised Service Centre. The majority of problems that can occur can be solved without the need Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The program does not start. • Make sure that the appliance door is closed.
ENGLISH 43 Problem and alarm code Possible cause and solution Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if applicable). The appliance door is difficult to close. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). • Parts of the tableware are protruding from the baskets.
www.aeg.com Problem Possible cause and solution There are stains and dry water drops on glasses and dishes. • The released quantity of rinse aid is not sufficient. Adjust the rinse aid level to a higher level. • The quality of the rinse aid can be the cause. The dishes are wet. • For the best drying performance activate the option XtraDry and set AirDry . • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty.
ENGLISH 45 Problem Possible cause and solution Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. 13.
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................46 2. CONSIGNES DE SÉCURITÉ......................................................................................48 3. DESCRIPTION DE L'APPAREIL.................................................................................50 4. PANNEAU DE COMMANDE....................................................................................51 5. PROGRAMMES....................
FRANÇAIS 47 pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • agréé ou un technicien qualifié afin d'éviter tout danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute. Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur.
FRANÇAIS 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant d'installer des tuyaux neufs, des tuyaux n'ayant pas servi depuis longtemps, lorsqu'une réparation a été effectuée ou qu'un nouveau dispositif a été installé (compteurs d'eau, etc.), laissez l'eau s'écouler jusqu'à ce qu'elle soit parfaitement propre et claire. • Pendant et après la première utilisation de l'appareil, vérifiez qu'aucune fuite n'est visible.
www.aeg.com 3.
FRANÇAIS 51 4. PANNEAU DE COMMANDE 1 2 8 1 2 3 4 5 Touche Marche/Arrêt Program touche Voyants de programme Affichage Delay touche 3 4 7 5 6 6 Option touche 7 Voyants 8 Start touche 4.1 Voyants Indicateur Description Phase de lavage. Il s'allume au cours des phases de lavage et de rinçage. Phase de rinçage. Il s'allume au cours de la phase de rinçage. Phase de séchage. Il s'allume au cours de la phase de séchage. Voyant de fin. Voyant TimeSaver. Voyant XtraDry.
www.aeg.com Indicateur Description Voyant ExtraHygiene. 5.
FRANÇAIS 53 5.1 Valeurs de consommation Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 10.5 0.932 225 7 - 14 0.6 - 1.6 40 - 170 12.5-14.5 1.4-1.7 170-190 12 - 14 0.7 - 0.9 82-92 10 0.9 30 9 - 10 1.1 - 1.3 230 - 250 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.com 6.2 Adoucisseur d'eau L'adoucisseur d'eau élimine les minéraux de l'arrivée d'eau qui pourraient avoir un impact négatif sur les résultats de lavage et sur l'appareil. Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région.
FRANÇAIS 6.3 Le distributeur de liquide de rinçage Le liquide de rinçage permet de sécher la vaisselle sans laisser de traînées ni de taches. Le liquide de rinçage est automatiquement ajouté au cours du rinçage chaud. Vous pouvez définir la quantité de liquide de rinçage libérée entre le niveau 1 (quantité minimale) et le niveau 6 (quantité maximale). Le dosage 0 désactive le distributeur de liquide de rinçage et le liquide de rinçage n'est pas diffusé. Réglage d'usine : niveau 4.
www.aeg.com 6.5 AirDry L'option AirDry améliore les résultats de séchage en utilisant moins d'énergie. Comment désactiver l'option AirDry L'appareil doit être en mode Programmation. 1. Pour entrer en mode utilisateur, maintenez les touches Delay et Option enfoncées simultanément jusqu'à ce que les voyants , , et se mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur Option. • Les voyants , et s'éteignent. Durant la phase de séchage, un dispositif ouvre la porte de l'appareil.
FRANÇAIS d'eau et la température du dernier rinçage peuvent être affectés. L'option XtraDry est une option permanente pour tous les programmes, à l'exception du programme pour lequel elle doit être sélectionnée à chaque cycle. À chaque fois que vous sélectionnez le programme , l'option XtraDry est désactivée et doit être sélectionnée manuellement. Pour les autres programmes, l'option XtraDry est permanente et automatiquement utilisée pour les cycles suivants.
www.aeg.com d'eau. Pendant ce temps, l'appareil semble ne pas fonctionner. La phase de lavage ne démarre qu'une fois cette procédure achevée. La procédure sera répétée régulièrement. 8.1 Réservoir de sel régénérant ATTENTION! Utilisez uniquement du sel régénérant conçu pour les lave-vaisselle. Le sel permet de recharger la résine dans l'adoucisseur d'eau et de garantir de bons résultats de lavage en utilisation quotidienne.
FRANÇAIS Remplissez le distributeur de liquide de rinçage lorsque le voyant (A) s'allume. 59 Si vous utilisez des pastilles de détergent multifonctions et que les performances du séchage sont satisfaisantes, l'indication de remplissage du liquide de rinçage peut être désactivée. Pour de meilleures performances de séchage, nous vous recommandons de toujours utiliser du liquide de rinçage, même si vous utilisez déjà des pastilles tout-en-1 contenant un agent de rinçage. 9. UTILISATION QUOTIDIENNE 1.
www.aeg.com Départ d'un programme 1. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation et que la porte est fermée. 2. Appuyez sur Program à plusieurs reprises jusqu'à ce que le voyant du programme que vous souhaitez sélectionner s'allume. L'affichage indique la durée du programme. 3. Sélectionnez les options compatibles. 4. Appuyez sur la touche Start pour lancer le programme. • Le voyant correspondant à la phase en cours s'allume.
FRANÇAIS que la fonction Auto Off l'éteigne automatiquement. Si vous ouvrez la porte avant l'activation de Auto Off, l'appareil est automatiquement éteint. 61 2. Fermez le robinet d'arrivée d'eau. 10. CONSEILS 10.1 Raccordement Les conseils suivants vous garantissent des résultats de lavage et de séchage optimaux au quotidien, et vous aideront à protéger l'environnement. • Videz les plus gros résidus alimentaires des plats dans une poubelle. • Ne rincez pas vos plats à la main au préalable.
www.aeg.com 4. Lorsque le programme de lavage est terminé, réglez l'adoucisseur d'eau en fonction de la dureté de l'eau dans votre région. 5. Ajustez la quantité de liquide de rinçage libérée. 6. Activez la notification du distributeur de liquide de rinçage vide. 10.4 Chargement des paniers • Utilisez uniquement cet appareil pour laver des articles qui peuvent passer au lave-vaisselle. • Ne mettez pas dans le lave-vaisselle des articles en bois, en corne, en aluminium, en étain et en cuivre.
FRANÇAIS 63 C B A 1. Faites pivoter le filtre (B) dans le sens antihoraire puis sortez-le. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat à sa place (A). Vérifiez qu'il est correctement positionné sous les deux guides. 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A).
www.aeg.com ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 4. Pour réinstaller le bras d'aspersion supérieur sur le panier, poussez le bras d'aspersion vers le haut, dans la direction indiquée par la flèche du bas, tout en le tournant vers la gauche jusqu'à ce qu'il se bloque en place.
FRANÇAIS 65 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'arrête en cours de programme. Avant de contacter le service après-vente agréé, vérifiez si vous pouvez résoudre le problème par vous-même à l'aide des informations du tableau. Pour certaines anomalies, l'écran affiche un code d'alarme. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé.
www.aeg.com Problème et code d'alarme Cause et solution possibles Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Fermez le robinet d'eau et contactez le service aprèsvente agréé. . L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps. • Sélectionnez l'option TimeSaver pour raccourcir la durée du programme.
FRANÇAIS 67 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
www.aeg.com Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage pour lavevaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble.
FRANÇAIS 69 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 818 - 898 / 575 Branchement électrique1) Tension (V) 220 - 240 Fréquence (Hz) 50 bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 13 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.
www.aeg.
FRANÇAIS 71
117884051-A-272017 www.aeg.