FEE63700PM NL EN FR USER MANUAL Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 25 47
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE......................................................................................... 2 2. VEILIGHEIDSVOORSCHRIFTEN.................................................................................4 3. BESCHRIJVING VAN HET PRODUCT........................................................................6 4. BEDIENINGSPANEEL................................................................................................. 7 5. PROGRAMMA’S..................
NEDERLANDS 3 niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • Leg het bestek in de besteklade met de scherpe randen naar beneden of leg ze horizontaal in de besteklade met de scherpe randen naar beneden. Laat om ongelukken te voorkomen het apparaat niet onbeheerd achter met open deur. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen onder druk en/of stoom om het apparaat te reinigen.
NEDERLANDS 2.3 Aansluiting aan de waterleiding • Beschadig de waterslangen niet. • Indien buizen lang niet zijn gebruikt, er reparaties hebben plaatsgevonden of er nieuwe apparaten zijn geplaatst (watermeters, enz.), moet u, voordat de nieuwe buizen worden aangesloten, het water laten stromen tot het schoon en helder is. • Zorg ervoor dat er geen zichtbare waterlekken zijn tijdens en na het eerste gebruik van het apparaat.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 3 8 1 2 3 4 5 Aan/uit-toets Program-toets Programma-indicatielampjes Weergave Delay-toets 4 7 5 6 6 Option-toets 7 Indicatielampjes 8 Start-toets 4.1 Indicatielampjes Aanduiding Beschrijving Wasfase. Gaat aan wanneer de wasfase en de spoelfases in werking zijn. Spoelfase. Gaat aan wanneer de spoelfase loopt. Droogfase. Gaat aan wanneer de droogfase loopt. Einde-indicatielampje. TimeSaver-indicatielampje. XtraDry-indicatielampje. Glansmiddelindicatielampje.
www.aeg.com Aanduiding Beschrijving ExtraHygiene-indicatielampje. 5.
NEDERLANDS 9 5.1 Verbruikswaarden Programma 1) Water (l) Energie (kWh) Bereidingsduur (min) 11 0.846 232 7 - 14 0.6 - 1.6 40 - 170 12.5-14.5 1.4-1.7 170-190 12 - 14 0.7 - 0.9 82-92 10 0.9 30 9 - 10 1.1 - 1.3 230 - 250 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.
www.aeg.com waterhardheid wordt gemeten in de volgende gelijkwaardige schalen. De waterontharder moet worden afgesteld op de hardheid van het water in uw woonplaats. Uw waterleidingbedrijf kan u informeren over de hardheid van het water in uw woonplaats. Het is belangrijk om het correcte niveau voor de waterontharder in te stellen voor goede wasresultaten. Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.
NEDERLANDS (hoogste hoeveelheid). Niveau 0 schakelt het glansmiddeldoseerbakje uit en er wordt geen glansmiddel afgegeven. Fabrieksinstelling: stand 4. Het apparaat moet in de programmakeuzemodus staan. Het apparaat moet in de programmakeuzemodus staan. 1. Houd om de gebruikersmodus in te voeren tegelijkertijd Delay en Option ingedrukt tot de , , en gaan knipperen en het display blanco is. 2. Druk op Delay. • De indicatielampjes uit.
www.aeg.com Tijdens de werking van de droogfase, wordt de deur van het apparaat door een instrument geopend. De deur blijft op een kier. LET OP! Probeer de deur van het apparaat niet binnen 2 minuten na automatisch openen te sluiten. Dit kan het apparaat beschadigen. LET OP! Indien er kinderen in de buurt zijn, kan het systeem AirDry worden uitgeschakeld als u aan het einde van de cyclus de deur gesloten wilt houden. Gebruik om de droogresultaten te verbeteren de optie XtraDry of activeer AirDry. 1.
NEDERLANDS Het activeren van XtraDry Druk op Option totdat het incatielampje aangaat. Het display geeft de bijgewerkte programmaduur weer. 7.2 TimeSaver De TimeSaver maakt verkorten van de tijd van het geselecteerde programma mogelijk. De totale duur van het programma neemt met ongeveer 50% af. De wasresultaten zijn hetzelfde als bij de normale programmaduur. De droogresultaten nemen mogelijk iets af. Met deze optie verhoogt u de druk en de temperatuur van het water. De wasen droogfasen zijn korter.
www.aeg.com 2. Doe 1 liter water in het zoutreservoir (alleen de eerste keer). 3. Vul het zoutreservoir met regenereerzout. 8.2 Het vullen van het glansmiddeldoseerbakje A B 4. Verwijder het zout rond de opening van het zoutreservoir. C LET OP! Gebruik alleen glansmiddel voor afwasautomaten. 5. Draai de dop van het zoutreservoir rechtsom om het zoutreservoir te sluiten. LET OP! Water en zout kunnen uit het zoutreservoir stromen als u het bijvult.
NEDERLANDS 15 9. DAGELIJKS GEBRUIK 1. Draai de waterkraan open. 2. Druk op de aan-/uittoets om het apparaat te activeren. Zorg dat het apparaat in de programmakeuzemodus staat. • Vul het zoutreservoir als het zoutindicatielampje brandt. • Vul het glansmiddeldoseerbakje als het indicatielampje van het glansmiddel brandt. 3. Ruim de korven in. 4. Voeg vaatwasmiddel toe. 5. U dient het juiste programma in te stellen en te starten voor het type lading en de mate van vervuiling. 9.
www.aeg.com Als het aftellen klaar is, start het programma en gaat het indicatielampje van de lopende fase branden. Het lampje uitgestelde start gaat uit. De deur openen als het apparaat in werking is Als u de deur opent terwijl een programma loopt, stopt het apparaat. Dit kan het energieverbruik en de programmaduur beïnvloeden. Als u de deur weer sluit, gaat het apparaat verder vanaf het punt van onderbreking.
NEDERLANDS 10.2 Gebruik van zout, glansmiddel en vaatwasmiddel • Gebruik enkel zout, glansmiddel en vaatwasmiddel voor afwasautomaten. Overige producten kunnen het apparaat beschadigen. • Maar in gebieden met hard en erg hard water raden we het gebruik aan van enkelvoudig vaatwasmiddel (poeder, gel, tabletten zonder extra middelen), met afzonderlijk glansmiddel en zout voor optimale reinigings- en droogresultaten.
www.aeg.com Aan het einde van het programma kan er water aan de zijkanten en de deur van het apparaat achterblijven. 11. ONDERHOUD EN REINIGING WAARSCHUWING! Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Vuile filters en verstopte sproeiarmen verminderen de wasresultaten. Controleer regelmatig de filters en reinig deze zo nodig. 2. Verwijder de filter (C) uit de filter (B). 3. Verwijder de platte filter (A). 11.
NEDERLANDS 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. LET OP! Een onjuiste plaatsing van de filters kan leiden tot slechte wasresultaten en het apparaat beschadigen. 11.2 De bovenste sproeiarm schoonmaken 3. Reinig de sproeiarm onder stromend water. Gebruik een smal en puntig gereedschap, bijv. een tandenstoker, om de vuildeeltjes uit de gaten te verwijderen. 4.
www.aeg.com • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen. 11.4 De binnenkant van de machine reinigen • Reinig het apparaat zorgvuldig, inclusief de rubberen afdichting van de deur, met een zachte, vochtige doek. • Als u regelmatig korte programma's gebruikt dan kunnen er vetresten en kalkaanslag achterblijven in het apparaat. Om dit te voorkomen raden wij aan om minstens twee keer per maand langdurige programma´s te gebruiken.
NEDERLANDS 21 Probleem en alarmcode Mogelijke oorzaak en oplossing Het apparaat wordt niet gevuld met water. Op het display verschijnt • Verzeker u ervan dat de waterkraan geopend is. • Ga na of de druk van de watervoorziening niet te laag is. Neem voor deze informatie contactpersoon op met uw plaatselijke waterleidingsbedrijf. • Verzeker u ervan dat de waterkraan niet verstopt is. • Controleer of het filter in de toevoerslang niet verstopt is.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing Het apparaat maakt kortslui- • De stroomsterkte is onvoldoende om alle tegelijk werting. kende apparaten van stroom te voorzien. Controleer de stroomsterkte van het stopcontact en het vermogen op de meter, of zet één van de in gebruik zijnde apparaten uit. • Interne elektrische storing van het apparaat. Neem contact op met de klantenservice.
NEDERLANDS 23 Probleem Mogelijke oorzaak en oplossing Het serviesgoed is nat. • Activeer voor de beste droogprestatie de optie XtraDry en stel AirDry in. • Het programma heeft geen droogfase of heeft een droogfase met lage temperatuur. • Het glansmiddeldoseerbakje is leeg. • De kwaliteit van het glansmiddel kan de oorzaak zijn. • De kwaliteit van de multitabletten kan de oorzaak zijn. Probeer een ander merk of activeer het glansmiddeldoseerbakje en gebruik het glansmiddel samen met de multitabletten.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Dof, ontkleurd of afgeschilverd serviesgoed. • Zorg dat alleen vaatwasmachinebestendige voorwerpen in het apparaat worden gewassen. • Laad de korf voorzichtig in en uit. Raadpleeg de folder voor het laden van de korven. • Leg tere voorwerpen in de bovenkorf. Raadpleeg "Voor het eerste gebruik", "Dagelijks gebruik" of "Aanwijzingen en tips" voor mogelijke andere oorzaken. 13.
ENGLISH 25 CONTENTS 1. SAFETY INFORMATION........................................................................................... 25 2. SAFETY INSTRUCTIONS...........................................................................................27 3. PRODUCT DESCRIPTION.........................................................................................28 4. CONTROL PANEL..................................................................................................... 29 5. PROGRAMMES..........
www.aeg.com manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
ENGLISH • • • • • 27 Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. If the appliance has ventilation openings in the base, they must not be covered e.g. by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets.
www.aeg.com WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance.
ENGLISH 5 6 7 8 9 Rating plate Salt container Air vent Rinse aid dispenser Detergent dispenser 29 10 Lower basket 11 Upper basket 12 Cutlery drawer 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase and the rinsing phases operate. Rinsing phase. It comes on when the rinsing phase operates.
www.aeg.com Indicator Description XtraDry indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. Delay indicator. ExtraHygiene indicator. 5.
ENGLISH Programme 4) Degree of soil Type of load Programme phases • Normal soil • Prewash • Crockery and cut- • Wash 50 °C lery • Rinses • Dry 31 Options • XtraDry 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets .
www.aeg.com 6.2 The water softener These settings will be saved until you change them again. The water softener removes minerals from the water supply, which would have a detrimental effect on the washing results and on the appliance. How to set the programme selection mode The appliance is in programme selection mode when the programme indicator The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales.
ENGLISH , and start to flash and the display is blank. 2. Press Program. • The indicators , and go off. continues to • The indicator flash. • The display shows the current setting: e.g. = level 5. 3. Press Program again and again to change the setting. 4. Press the on/off button to confirm the setting. 6.3 The rinse aid dispenser The rinse aid is automatically released during the hot rinse phase.
www.aeg.com To improve the drying performance refer to the XtraDry option or activate AirDry. How to deactivate AirDry The appliance must be in programme selection mode. 1. To enter the user mode, press and hold simultaneously Delay and Option until the indicators While the drying phase operates, a device opens the appliance door. The door is then kept ajar. CAUTION! Do not try to close the appliance door within 2 minutes after automatic open. This can cause damage to the appliance.
ENGLISH configuration can be changed at any time. How to activate TimeSaver Activating XtraDry option deactivates TimeSaver. Press Option until the indicator comes on. If the option is not applicable to the programme, the related indicator does not come on or it flashes quickly for a few seconds and then goes off. The display shows the updated programme duration. How to activate XtraDry Press Option until the indicator comes on. The display shows the updated programme duration. 7.
www.aeg.com 8.2 How to fill the rinse aid dispenser A B 4. Remove the salt around the opening of the salt container. C 5. Turn the cap of the salt container clockwise to close the salt container. CAUTION! Water and salt can come out of the salt container when you fill it. After you fill the salt container, immediately start a programme to prevent corrosion. CAUTION! Only use rinse aid specifically designed for dishwashers. 1. Open the lid (C). 2.
ENGLISH 37 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil. 9.1 Using the detergent A B C CAUTION! Only use detergent specifically designed for dishwashers.
www.aeg.com Opening the door while the appliance operates If you open the door while a programme is running, the appliance stops. It may affect the energy consumption and the programme duration. When you close the door, the appliance continues from the point of interruption. If the door is opened for more than 30 seconds during the drying phase, the running programme will end. This will not happen if the door is opened by AirDry.
ENGLISH 10.2 Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance. • In areas with hard and very hard water we recommend to use plain dishwasher detergent (powder, gel, tablets containing no additional agents), rinse aid and salt separately for optimal cleaning and drying results. • At least once a month run the appliance with the use of appliance cleaner which is particularly suitable for this purpose.
www.aeg.com 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. 3. Remove the flat filter (A). 4. Wash the filters. 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6.
ENGLISH CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the upper spray arm 41 4. To engage again the spray arm to the basket, press the spray arm upwards in the direction indicated by the lower arrow and simultaneously turn it counterclockwise until it locks into place. We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. Clogged holes can cause unsatisfactory washing results. 1.
www.aeg.com Follow carefully the instructions on the packaging of the product. 12. TROUBLESHOOTING If the appliance does not start or it stops during operation, first check if you can solve the problem by yourself with the help of the information in the table or contact an Authorised Service Centre. WARNING! Repairs not properly done may result in serious risk to the safety of the user. Any repairs must be performed by qualified personnel. With some problems, the display shows an alarm code.
ENGLISH 43 Problem and alarm code Possible cause and solution The program lasts too long. • Select the TimeSaver option to shorten the program time. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown. The remaining time in the • This is not a defect. The appliance is working correctly. display increases and skips nearly to the end of program time. Small leak from the appliance door. • The appliance is not levelled.
www.aeg.com Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option XtraDry and set AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets.
ENGLISH 45 Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. The level of salt is low, check the refill indicator. The cap of the salt container is loose. Your tap water is hard.
www.aeg.com appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
FRANÇAIS 47 TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................47 2. CONSIGNES DE SÉCURITÉ......................................................................................49 3. DESCRIPTION DE L'APPAREIL.................................................................................51 4. PANNEAU DE COMMANDE....................................................................................52 5. PROGRAMMES.......................
www.aeg.com pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
FRANÇAIS • • • • • • 49 agréé ou un technicien qualifié afin d'éviter tout danger. Placez les couverts dans le panier à couverts, avec les extrémités pointues vers le bas, ou placez-les dans le bac à couverts en position horizontale, bords tranchants vers le bas. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter de vous prendre accidentellement les pieds dedans. Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur.
www.aeg.com changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant d'installer des tuyaux neufs, des tuyaux n'ayant pas servi depuis longtemps, lorsqu'une réparation a été effectuée ou qu'un nouveau dispositif a été installé (compteurs d'eau, etc.), laissez l'eau s'écouler jusqu'à ce qu'elle soit parfaitement propre et claire.
FRANÇAIS 3.
www.aeg.com 4. PANNEAU DE COMMANDE 1 2 8 1 2 3 4 5 Touche Marche/Arrêt Program touche Voyants de programme Affichage Delay touche 3 4 7 5 6 6 Option touche 7 Voyants 8 Start touche 4.1 Voyants Indicateur Description Phase de lavage. Il s'allume au cours des phases de lavage et de rinçage. Phase de rinçage. Il s'allume au cours de la phase de rinçage. Phase de séchage. Il s'allume au cours de la phase de séchage. Voyant de fin. Voyant TimeSaver. Voyant XtraDry.
FRANÇAIS Indicateur 53 Description Voyant ExtraHygiene. 5.
www.aeg.com 5.1 Valeurs de consommation Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 11 0.846 232 7 - 14 0.6 - 1.6 40 - 170 12.5-14.5 1.4-1.7 170-190 12 - 14 0.7 - 0.9 82-92 10 0.9 30 9 - 10 1.1 - 1.3 230 - 250 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
FRANÇAIS 6.2 Adoucisseur d'eau L'adoucisseur d'eau élimine les minéraux de l'arrivée d'eau qui pourraient avoir un impact négatif sur les résultats de lavage et sur l'appareil. Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. 55 L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région.
www.aeg.com 6.3 Le distributeur de liquide de rinçage Le liquide de rinçage permet de sécher la vaisselle sans laisser de traînées ni de taches. Le liquide de rinçage est automatiquement ajouté au cours du rinçage chaud. Vous pouvez définir la quantité de liquide de rinçage libérée entre le niveau 1 (quantité minimale) et le niveau 6 (quantité maximale). Le dosage 0 désactive le distributeur de liquide de rinçage et le liquide de rinçage n'est pas diffusé. Réglage d'usine : niveau 4.
FRANÇAIS 6.5 AirDry L'option AirDry améliore les résultats de séchage en utilisant moins d'énergie. 57 Pour améliorer les performances de séchage, reportez-vous à l'option XtraDry ou activez l'option AirDry. Comment désactiver l'option AirDry L'appareil doit être en mode Programmation. 1. Pour entrer en mode utilisateur, maintenez les touches Delay et Option enfoncées simultanément jusqu'à ce que les voyants Durant la phase de séchage, un dispositif ouvre la porte de l'appareil.
www.aeg.com En utilisant cette option, la durée de certains programmes, la consommation d'eau et la température du dernier rinçage peuvent être affectés. L'option XtraDry est une option permanente pour tous les programmes, à l'exception du programme pour lequel elle doit être sélectionnée à chaque cycle. À chaque fois que vous sélectionnez le programme , l'option XtraDry est désactivée et doit être sélectionnée manuellement.
FRANÇAIS 59 Lorsque vous démarrez un programme, l'appareil peut prendre 5 minutes pour recharger la résine dans l'adoucisseur d'eau. Pendant ce temps, l'appareil semble ne pas fonctionner. La phase de lavage ne démarre qu'une fois cette procédure achevée. La procédure sera répétée régulièrement. 8.1 Réservoir de sel régénérant ATTENTION! Utilisez uniquement du sel régénérant conçu pour les lave-vaisselle.
www.aeg.com 2. Remplissez le distributeur (B) jusqu'à ce que le liquide de rinçage atteigne le repère « MAX ». 3. Si le liquide de rinçage déborde, épongez-le avec un chiffon absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. Si vous utilisez des pastilles de détergent multifonctions et que les performances du séchage sont satisfaisantes, l'indication de remplissage du liquide de rinçage peut être désactivée.
FRANÇAIS Départ d'un programme 1. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation et que la porte est fermée. 2. Appuyez sur Program à plusieurs reprises jusqu'à ce que le voyant du programme que vous souhaitez sélectionner s'allume. L'affichage indique la durée du programme. 3. Sélectionnez les options compatibles. 4. Appuyez sur la touche Start pour lancer le programme. • Le voyant correspondant à la phase en cours s'allume.
www.aeg.com que la fonction Auto Off l'éteigne automatiquement. Si vous ouvrez la porte avant l'activation de Auto Off, l'appareil est automatiquement éteint. 2. Fermez le robinet d'arrivée d'eau. 10. CONSEILS 10.1 Raccordement Les conseils suivants vous garantissent des résultats de lavage et de séchage optimaux au quotidien, et vous aideront à protéger l'environnement. • Videz les plus gros résidus alimentaires des plats dans une poubelle. • Ne rincez pas vos plats à la main au préalable.
FRANÇAIS 4. Lorsque le programme de lavage est terminé, réglez l'adoucisseur d'eau en fonction de la dureté de l'eau dans votre région. 5. Ajustez la quantité de liquide de rinçage libérée. 6. Activez la notification du distributeur de liquide de rinçage vide. 10.4 Chargement des paniers • Utilisez uniquement cet appareil pour laver des articles qui peuvent passer au lave-vaisselle. • Ne mettez pas dans le lave-vaisselle des articles en bois, en corne, en aluminium, en étain et en cuivre.
www.aeg.com C B A 1. Faites pivoter le filtre (B) dans le sens antihoraire puis sortez-le. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat à sa place (A). Vérifiez qu'il est correctement positionné sous les deux guides. 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A).
FRANÇAIS ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 65 4. Pour réinstaller le bras d'aspersion supérieur sur le panier, poussez le bras d'aspersion vers le haut, dans la direction indiquée par la flèche du bas, tout en le tournant vers la gauche jusqu'à ce qu'il se bloque en place.
www.aeg.com 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'il s'arrête en cours de fonctionnement, vérifiez d'abord si vous pouvez résoudre le problème par vous-même en vous aidant des informations du tableau ou contactez le Service après-vente agréé. Pour certaines anomalies, l'écran affiche un code d'alarme. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé.
FRANÇAIS 67 Problème et code d'alarme Cause et solution possibles Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Fermez le robinet d'eau et contactez le service aprèsvente agréé. . L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps. • Sélectionnez l'option TimeSaver pour raccourcir la durée du programme.
www.aeg.com 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
FRANÇAIS 69 Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage pour lavevaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble.
www.aeg.com 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 818 - 898 / 575 Branchement électrique1) Tension (V) 220 - 240 Fréquence (Hz) 50 bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 15 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.
FRANÇAIS 71
117884881-A-262017 www.aeg.