FES5261XZW FES5261XZD FES5261XZM USER MANUAL DE Benutzerinformation Geschirrspüler
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................4 3. GERÄTEBESCHREIBUNG........................................................................................... 6 4. BEDIENFELD................................................................................................................7 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com • • • • • • • • • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt. Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, seinem autorisierten Kundenservice oder einer gleichermaßen qualifizierten Person ausgetauscht werden, um Gefahrenquellen zu vermeiden.
DEUTSCH • • • • • • • Typenschild den Daten Ihrer Stromversorgung entsprechen. Wenden Sie sich anderenfalls an eine Elektrofachkraft. Schließen Sie das Gerät unbedingt an eine sachgemäß installierte Schutzkontaktsteckdose an. Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen.
www.aeg.com • Schneiden Sie das Netzkabel ab, und entsorgen Sie es. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in dem Gerät einschließen. 3.
DEUTSCH 4. BEDIENFELD 1 2 3 8 1 2 3 4 5 4 7 Taste „Ein/Aus“ Taste Program Programmkontrolllampen Display Taste Delay 5 6 6 Taste Option 7 Kontrolllampen 8 Taste Start 4.1 Kontrolllampen Kontrolllampe Beschreibung Hauptspülgang. Leuchtet während des Hauptspülgangs auf. Spülgang. Leuchtet während der Spülphase auf. Trockenphase. Leuchtet während der Trocknungsphase auf. Kontrolllampe Programmende. Kontrolllampe TimeSaver. Kontrolllampe XtraDry. Kontrolllampe Klarspülmittel.
www.aeg.com Kontrolllampe Beschreibung Kontrolllampe Delay. Kontrolllampe Tür. Leuchtet, wenn die Tür des Geräts offen oder nicht richtig geschlossen ist. 5.
DEUTSCH 9 5.1 Verbrauchswerte Programm1) Wasserverbrauch (l) Energieverbrauch (kWh) Dauer (min.) 9.9 0.920 237 7 - 12 0.7 - 1.5 45 - 160 13 - 15 1.4 - 1.6 140 - 160 9 0.8 30 13 - 14 0.9 - 1.1 70 - 85 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Informationen für Prüfinstitute info.test@dishwasher-production.
www.aeg.com unbedingt auf die richtige Stufe eingestellt werden, um gute Spülergebnisse zu garantieren. Wasserhärte Deutsche Wasserhärtegrade (°dH) Französische Wasserhärtegrade (°fH) mmol/l Clarke Was- Einstellung für den serhärtegra- Wasserenthärter de 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.
DEUTSCH Klarspülmittelnachfüllanzeige Das Klarspülmittel ermöglicht das Trocknen des Geschirrs ohne Streifen und Flecken. Das Klarspülmittel wird automatisch während der heißen Spülphasen abgegeben. 11 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. 6.4 AirDry AirDry verbessert die Trocknungsergebnisse bei einem geringeren Energieverbrauch.
www.aeg.com und blinken und das Display nichts anzeigt. 2. Drücken Sie Delay. • Die Kontrolllampen und erlöschen. • Die Kontrolllampe weiter. blinkt • Im Display wird die aktuelle Einstellung angezeigt: = AirDry eingeschaltet. 3. Drücken Sie Delay zur Änderung der Einstellung: = AirDry ausgeschaltet. 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. 7. OPTIONEN Sie müssen die gewünschten Optionen vor dem Programmstart einschalten.
DEUTSCH 13 8. VOR DER ERSTEN INBETRIEBNAHME 1. Prüfen Sie, ob die Einstellung des Wasserenthärters der Wasserhärte in Ihrem Gebiet entspricht. Wenn nicht, stellen Sie die Wasserenthärterstufe ein. 2. Füllen Sie den Salzbehälter. 3. Füllen Sie den KlarspülmittelDosierer. 4. Öffnen Sie den Wasserhahn. 5. Starten Sie ein Programm, um Fertigungsrückstände, die sich möglicherweise noch im Gerät befinden können, zu beseitigen. Verwenden Sie kein Reinigungsmittel und beladen Sie die Körbe nicht.
www.aeg.com B A M AX 4 1 3 2 + - C D 1. Drücken Sie die Entriegelungstaste (D), um den Deckel (C) zu öffnen. 2. Füllen Sie den KlarspülmittelDosierer (A) bis zur Markierung „max“. 3. Wischen Sie verschüttetes Klarspülmittel mit einem saugfähigen Tuch auf, um zu große Schaumbildung zu vermeiden. 4. Schließen Sie den Deckel. Achten Sie darauf, dass die Entriegelungstaste einrastet.
DEUTSCH 9.2 Einstellen und Starten eines Programms Funktion Auto Off Mit dieser Funktion wird der Energieverbrauch gesenkt, da sich das Gerät automatisch ausschaltet, wenn es nicht in Betrieb ist. Die Funktion schaltet sich in folgenden Fällen ein: • 5 Minuten nach Programmende. • Nach 5 Minuten, wenn das Programm nicht gestartet wurde. Starten eines Programms 1. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten.
www.aeg.com Beenden des Programms Halten Sie Delay und Option gleichzeitig gedrückt, bis sich das Gerät im Programmwahlmodus befindet. Bevor Sie ein neues Programm starten, stellen Sie sicher, dass der Reinigungsmittelbehälter gefüllt ist. Programmende 1. Drücken Sie die Taste Ein/Aus oder warten Sie, bis das Gerät über die Funktion Auto Off automatisch ausgeschaltet wird. Wenn Sie die Tür öffnen, bevor die Funktion Auto Off eingeschaltet wird, wird das Gerät automatisch ausgeschaltet. 2.
DEUTSCH 1. Stellen Sie die höchste Wasserenthärterstufe ein. 2. Stellen Sie sicher, dass der Salzbehälter und der KlarspülmittelDosierer gefüllt sind. 3. Starten Sie das kürzeste Programm mit einer Spülphase. Verwenden Sie kein Reinigungsmittel und beladen Sie die Körbe nicht. 4. Stellen Sie den Wasserenthärter nach Ablauf des Programms auf die Wasserhärte in Ihrer Region ein. 5. Stellen Sie die Menge des Klarspülmittels ein. 6. Schalten Sie die Klarspülmittelnachfüllanzeige ein. 10.
www.aeg.com 11.1 Reinigen der Filter Das Filtersystem besteht aus 3 Teilen. C B A 1. Drehen Sie den Filter (B) nach links und nehmen Sie ihn heraus. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 4. Reinigen Sie die Filter. 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein.
DEUTSCH VORSICHT! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 11.2 Reinigen der Sprüharme Bauen Sie die Sprüharme nicht aus. Falls die Löcher in den Sprüharmen verstopft sind, reinigen Sie sie mit einem dünnen spitzen Gegenstand. 11.3 Reinigen der Außenseiten • Reinigen Sie das Gerät mit einem weichen, feuchten Tuch. • Verwenden Sie ausschließlich Neutralreiniger.
www.aeg.com Störung und Alarmcode Mögliche Ursache und Abhilfe Das Programm startet nicht. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Drücken Sie Start. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie diese ab, oder warten Sie, bis sie abgelaufen ist. • Das Gerät regeneriert das Filterharz des Wasserenthärters. Dieser Vorgang dauert ca. 5 Minuten. Es läuft kein Wasser in das Gerät. • Stellen Sie sicher, dass der Wasserzulaufhahn geöffnet ist.
DEUTSCH Störung und Alarmcode Mögliche Ursache und Abhilfe Die Gerätetür ist schwer zu schließen. • Das Gerät ist nicht ausgerichtet. Schrauben Sie die Schraubfüße weiter hinein oder weiter heraus (falls vorhanden). • Teile des Geschirrs ragen aus den Körben heraus. 21 Klappernde/schlagende Ge- • Das Geschirr ist nicht richtig in den Körben eingeordnet. räusche aus dem GeräteinSiehe Broschüre zum Beladen der Körbe. neren. • Achten Sie darauf, dass sich die Sprüharme frei drehen können.
www.aeg.com Störung Mögliche Ursache und Abhilfe Nicht zufriedenstellende Trocknungsergebnisse. • Das Geschirr stand zu lange im geschlossenen Gerät. • Es ist kein Klarspülmittel vorhanden oder die Klarspülmittelmenge ist nicht ausreichend. Stellen Sie den Klarspülmittel-Dosierer auf eine höhere Einstellung. • Kunststoffteile müssen eventuell mit einem Tuch abgetrocknet werden. • Schalten Sie die Option XtraDry ein, und stellen Sie AirDry ein, um die beste Trocknungsleistung zu erzielen.
DEUTSCH 23 Störung Mögliche Ursache und Abhilfe Am Ende des Programms befinden sich Reinigungsmittelreste im Behälter. • Das Reinigungsmittel-Tab blieb im Behälter stecken und wurde daher nicht vollständig vom Wasser mitgenommen. • Das Wasser kann das Reinigungsmittel nicht aus dem Behälter ausspülen. Achten Sie darauf, dass der Sprüharm nicht blockiert oder verstopft ist. • Stellen Sie sicher, dass die im Korb eingeordneten Gegenstände ein Öffnen des Reinigungsmittelbehälters nicht verhindern.
www.aeg.com Wasserversorgung Kalt- oder Warmwasser 2) max. 60 °C Fassungsvermögen Maßgedecke 13 Leistungsaufnahme Ein-Zustand (W) 5.0 Leistungsaufnahme Aus-Zustand (W) 0.50 1) Weitere Angaben finden Sie auf dem Typenschild. 2) Wenn Sie Heißwasser mit umweltfreundlichen, alternativen Energiequellen (z. B. Solaranlagen oder Windkraft) aufbereiten, können Sie durch den Anschluss des Geräts an die Heißwasserversorgung Energie sparen. 14. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol .
DEUTSCH 25
www.aeg.
DEUTSCH 27
156910741-A-322017 www.aeg.