FFB41600ZW FFB41600ZM USER MANUAL NL FR Gebruiksaanwijzing Afwasautomaat Notice d'utilisation Lave-vaisselle 2 24
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE......................................................................................... 2 2. VEILIGHEIDSVOORSCHRIFTEN.................................................................................4 3. BESCHRIJVING VAN HET PRODUCT........................................................................6 4. BEDIENINGSPANEEL................................................................................................. 7 5. PROGRAMMA’S..................
NEDERLANDS 3 niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • Leg het bestek in de besteklade met de scherpe randen naar beneden of leg ze horizontaal in de besteklade met de scherpe randen naar beneden. Laat om ongelukken te voorkomen het apparaat niet onbeheerd achter met open deur. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen onder druk en/of stoom om het apparaat te reinigen.
NEDERLANDS of er nieuwe apparaten zijn geplaatst (watermeters, enz.), moet u, voordat de nieuwe buizen worden aangesloten, het water laten stromen tot het schoon en helder is. • Zorg ervoor dat er geen zichtbare waterlekken zijn tijdens en na het eerste gebruik van het apparaat. • De watertoevoerslang heeft een veiligheidsventiel en een omhulsel met een hoofdkabel aan de binnenkant. • Vaatwasmiddel is gevaarlijk. Volg de veiligheidsinstructies op de verpakking van het wasmiddel op.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 8 1 2 3 4 5 Aan/uit-toets Program-toets Programma-indicatielampjes Weergave Delay-toets 3 4 7 5 6 6 Option-toets 7 Indicatielampjes 8 Start-toets 4.1 Indicatielampjes Aanduiding Beschrijving Wasfase. Gaat aan wanneer de wasfase loopt. Spoelfase. Gaat aan wanneer de spoelfase loopt. Droogfase. Gaat aan wanneer de droogfase loopt. Einde-indicatielampje. XtraDry-indicatielampje. Glansmiddelindicatielampje.
www.aeg.com Aanduiding Beschrijving ExtraHygiene-indicatielampje. Deur-indicatielampje. Gaat aan als de deur niet goed is geopend of gesloten. 5.
NEDERLANDS Programma 1) Water (l) Energie (kWh) Programmaduur (min.) 10 0.8 30 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten info.test@dishwasher-production.com Schrijf het productnummer (PNC) op dat u op het typeplaatje vindt. Stuur voor alle benodigde informatie over testprestaties een e-mail naar: 6. INSTELLINGEN 6.
www.aeg.com Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Fabrieksinstelling. 2) Gebruik geen zout op dit niveau.
NEDERLANDS Het uitschakelen van de melding van een leeg glansmiddeldoseerbakje LET OP! Probeer de deur van het apparaat niet binnen 2 minuten na automatisch openen te sluiten. Dit kan het apparaat beschadigen. Het apparaat moet in de programmaselectiemodus staan. 1. Als u naar de gebruikersmodus wilt gaan, houdt u Delay en Option gelijktijdig ingedrukt totdat de indicatielampjes , en beginnen te knipperen en de display leeg is. 2. Druk op Start. • De indicatielampjes zijn uit.
www.aeg.com 7. OPTIES De gewenste opties moeten elke keer dat u een programma start worden geactiveerd. De opties kunnen niet worden in- of uitgeschakeld als een programma in werking is. Niet alle opties kunnen met elkaar worden gecombineerd. Als u opties hebt geselecteerd die niet met elkaar te combineren zijn, dan schakelt het apparaat automatisch één of meerdere opties uit. Alleen de indicatielampjes van de actieve opties blijven aan. 7.
NEDERLANDS herladen. Het lijkt alsof het apparaat niet werkt. De wasfase start pas nadat deze procedure voltooid is. De procedure wordt regelmatig herhaald. 13 8.2 Het vullen van het glansmiddeldoseerbakje A D B 8.1 Het zoutreservoir LET OP! Gebruik alleen zout dat voor afwasautomaten is gemaakt. Het zout wordt gebruikt om de hars in de waterontharder te herladen en voor goede wasresultaten voor dagelijks gebruik. C Het zoutreservoir vullen B A M AX 4 3 2 + 1 1.
www.aeg.com 9. DAGELIJKS GEBRUIK 1. Draai de waterkraan open. 2. Druk op de aan-/uittoets om het apparaat te activeren. Zorg dat het apparaat in de programmakeuzemodus staat. • Vul het zoutreservoir als het zoutindicatielampje brandt. • Vul het glansmiddeldoseerbakje als het indicatielampje van het glansmiddel brandt. 3. Ruim de korven in. 4. Voeg vaatwasmiddel toe. 5. U dient het juiste programma in te stellen en te starten voor het type lading en de mate van vervuiling. 2.
NEDERLANDS 3. Druk op Start om het aftellen te starten. • Het controlelampje uitgestelde start gaat aan om de start van het aftellen te bevestigen. • Het aftellen vindt plaats in stappen van 1 uur. Alleen het laatste uur telt af in stappen van 1 minuut. Als het aftellen klaar is, start het programma en gaat het indicatielampje van de lopende fase branden. Het lampje uitgestelde start gaat uit.
www.aeg.com • U kunt apart vaatwasmiddel, glansmiddel en zout gebruiken of kiezen voor het gebruik van multitabletten (bijv. ''3in1'', ''4in1'', ''All in 1''). Volg de aanwijzing op de verpakking. • U dient het juiste programma in te stellen voor het type lading en de mate van vervuiling. Het programma ECO biedt het meest efficiënte wateren energieverbruik voor normaal vervuild serviesgoed en bestek. 10.
NEDERLANDS • De positie van de items in de mandjes correct is. • Het programma van toepassing is op het type lading en de mate van bevuiling. • De juiste hoeveelheid afwasmiddel is gebruikt. 17 borden zijn gevoelig voor beschadigingen. 2. Ruim eerst het onderrek en dan het bovenrek uit. Aan het einde van het programma kan er water aan de zijkanten en de deur van het apparaat achterblijven. 10.6 De rekken uitruimen 1. Laat de borden afkoelen voordat u deze uit het apparaat neemt. Hete 11.
www.aeg.com LET OP! Een onjuiste plaatsing van de filters kan leiden tot slechte wasresultaten en het apparaat beschadigen. 11.2 De sproeiarmen reinigen Probeer niet de sproeiarmen te verwijderen. Als etensresten de openingen in de sproeiarmen hebben verstopt, verwijder deze dan met een smal en puntig voorwerp. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter terug (A). Zorg ervoor dat het goed onder de 2 geleidingen zit. 11.
NEDERLANDS 19 12. PROBLEEMOPLOSSING Als het apparaat niet start of stopt tijdens de bediening, kijk dan of u het probleem zelf kunt oplossen met behulp van de informatie in de tabel of door contact op te nemen met een erkend servicecentrum. WAARSCHUWING! Niet juist uitgevoerde reparaties kunnen de veiligheid van de gebruiker ernstig in gevaar brengen. Alle reparaties moeten worden uitgevoerd door bevoegd personeel. Bij sommige problemen wordt er op de display een alarmcode weergegeven.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing De anti-overstromingsbevei- • Draai de waterkraan dicht en neem contact op met de liging is ingeschakeld. service-afdeling. Op het display verschijnt . Het apparaat stopt en start meerdere keren tijdens de werking. • Dat is normaal. Het voorziet in optimale reinigingsresultaten en energiebesparing. Het programma duurt te lang.
NEDERLANDS 21 12.1 De was- en droogresultaten zijn niet naar tevredenheid Probleem Mogelijke oorzaak en oplossing Slechte wasresultaten. • Raadpleeg "Dagelijks gebruik", "Aanwijzingen en tips" en de folder voor het laden van de korf. • Gebruik intensievere wasprogramma´s. • Maak de inspuiters van de sproeiarm en het filter schoon. Zie "Onderhoud en reiniging". Slechte droogresultaten. • Serviesgoed heeft te lang in het gesloten apparaat gestaan.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Roestresten op bestek. • Er wordt voor het wassen teveel zout in het water gebruikt. Zie 'De waterontharder instellen'. • Zilver en roestvrijstalen bestek zijn samen geplaatst. Zet zilveren en roestvrijstalen voorwerpen niet dicht bij elkaar. Er bevinden zich aan het einde • De vaatwastablet raakte klem in het vaatwasmiddeldovan het programma resten van seerbakje en is daardoor niet volledig weggespoeld vaatwasmiddel in het vaatwasdoor het water.
NEDERLANDS Watertoevoerdruk Min. / max. bar (MPa) Watertoevoer Koud water of warm water2) max. 60 °C Vermogen Couverts 13 Energieverbruik Modus aan laten (W) 5.0 Energieverbruik Uit-modus (W) 0.50 23 0.5 (0.05) / 8 (0.8) 1) Zie het typeplaatje voor andere waarden. 2) Als het hete water door alternatieve, milieuvriendelijkere energiebronnen geproduceerd wordt (bijv. zonnepanelen en windenergie), gebruik dan een heetwatervoorziening om het energieverbruik te verminderen. 14.
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................24 2. CONSIGNES DE SÉCURITÉ......................................................................................26 3. DESCRIPTION DE L'APPAREIL.................................................................................28 4. BANDEAU DE COMMANDE....................................................................................29 5. PROGRAMMES....................
FRANÇAIS 25 pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • agréé ou un technicien qualifié afin d'éviter tout danger. Placez les couverts dans le panier à couverts, avec les extrémités pointues vers le bas, ou placez-les dans le bac à couverts en position horizontale, bords tranchants vers le bas. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter de vous prendre accidentellement les pieds dedans. Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur.
FRANÇAIS électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant d'installer des tuyaux neufs, des tuyaux n'ayant pas servi depuis longtemps, lorsqu'une réparation a été effectuée ou qu'un nouveau dispositif a été installé (compteurs d'eau, etc.), laissez l'eau s'écouler jusqu'à ce qu'elle soit parfaitement propre et claire.
www.aeg.com 3.
FRANÇAIS 4. BANDEAU DE COMMANDE 1 2 8 1 2 3 4 5 Touche Marche/Arrêt Touche Program Voyants de programme Affichage Touche Delay 3 4 7 5 6 6 Touche Option 7 Voyants 8 Touche Start 4.1 Voyants Indicateur Description Phase de lavage. Il s'allume au cours de la phase de lavage. Phase de rinçage. Il s'allume au cours de la phase de rinçage. Phase de séchage. Il s'allume au cours de la phase de séchage. Voyant de fin. Voyant XtraDry. Voyant du réservoir de liquide de rinçage.
www.aeg.com Indicateur Description Voyant ExtraHygiene. Voyant de porte. Il s'allume lorsque la porte de l'appareil est ouverte ou mal fermée. 5.
FRANÇAIS Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 10 0.8 30 31 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.2 Informations pour les instituts de test Pour toute information relative aux performances de test, envoyez un courrier électronique à l'adresse : info.test@dishwasher-production.
www.aeg.com Dureté eau Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Niveau de l'adoucisseur d'eau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
FRANÇAIS 33 s'allume pour signaler qu'un remplissage du liquide de rinçage est nécessaire. Si les résultats de séchage sont satisfaisants lors de l'utilisation de pastilles de détergent multifonctions, il est possible de désactiver la notification de remplissage du distributeur de liquide de rinçage Nous vous recommandons, cependant, de toujours utiliser du liquide de rinçage pour de meilleures performances du séchage.
www.aeg.com • Les voyants sont éteints. et • Le voyant clignote toujours. • L'affichage indique le réglage actuel : = AirDry activé. 3. Appuyez sur la touche Delay pour modifier le réglage : = AirDry désactivé. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 7. OPTIONS Vous devez activer les options souhaitées à chaque fois avant de lancer un programme. Vous ne pouvez pas activer ni désactiver d'options pendant le déroulement d'un programme.
FRANÇAIS 35 8. AVANT LA PREMIÈRE UTILISATION 1. Assurez-vous que le réglage actuel de l'adoucisseur d'eau est compatible avec la dureté de l'arrivée d'eau. Si ce n'est pas le cas, réglez le niveau de l'adoucisseur d'eau. 2. Remplissez le réservoir de sel régénérant. 3. Remplissez le distributeur de liquide de rinçage. 4. Ouvrez le robinet d'eau. 5. Lancez un programme pour éliminer tous les résidus qui peuvent toujours se trouver à l'intérieur de l'appareil.
www.aeg.com 8.2 Comment remplir le distributeur de liquide de rinçage A D ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. B C B A 1. Appuyez sur le bouton d'ouverture (D) pour ouvrir le couvercle (C). 2. Versez le liquide de rinçage dans le distributeur (A) jusqu'à ce qu'il atteigne le niveau « max ». 3. Si le liquide de rinçage déborde, épongez-le avec un chiffon absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle.
FRANÇAIS B A 30 D 20 C ATTENTION! Utilisez uniquement du produit de lavage spécifiquement conçu pour les lave-vaisselle. 1. Appuyez sur le bouton d'ouverture (B) pour ouvrir le couvercle (C). 2. Versez le produit de lavage, en poudre ou en pastilles, dans le compartiment (A). 3. Si le programme comporte une phase de prélavage, versez une petite quantité de produit de lavage dans le compartiment (D). 4. Fermez le couvercle. Assurez-vous que le bouton d'ouverture se verrouille correctement. 9.
www.aeg.com Durant la phase de séchage, si la porte est ouverte pendant plus de 30 secondes, le programme en cours s'arrête. Ceci ne se produit pas si la porte est ouverte par la fonction AirDry. Ne tentez pas de refermer la porte dans les 2 minutes suivant son ouverture automatique par la fonction AirDry car vous pourriez endommager l'appareil. Si par la suite vous refermez la porte pendant 3 minutes, le programme en cours se termine.
FRANÇAIS 10.2 Utilisation de sel régénérant, de liquide de rinçage et de produit de lavage • Utilisez uniquement du sel régénérant, du liquide de rinçage et du produit de lavage conçus pour les lave-vaisselle. D'autres produits peuvent endommager l'appareil.
www.aeg.com • Le programme est adapté au type de vaisselle et au degré de salissure. • Vous utilisez la bonne quantité de produit de lavage. vaisselle encore chaude est sensible aux chocs. 2. Commencez par décharger le panier inférieur, puis le panier supérieur. À la fin du programme, il peut rester de l'eau sur les parois et la porte de l'appareil. 10.6 Déchargement des paniers 1. Attendez que la vaisselle refroidisse avant de la retirer de l'appareil. La 11.
FRANÇAIS 41 ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d'aspersion. Si des résidus ont bouché les orifices des bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat (A) en place.
www.aeg.com 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'il s'arrête en cours de fonctionnement, vérifiez d'abord si vous pouvez résoudre le problème par vous-même en vous aidant des informations du tableau ou contactez le Service après-vente agréé. Pour certaines anomalies, l'écran affiche un code d'alarme. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé.
FRANÇAIS 43 Problème et code d'alarme Cause et solution possibles Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Fermez le robinet d'eau et contactez le service aprèsvente agréé. . L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps. • Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte.
www.aeg.com 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
FRANÇAIS 45 Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage pour lavevaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après-vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble.
www.aeg.com 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 600 / 850 / 625 Branchement électrique 1) Tension (V) 200 - 240 Fréquence (Hz) 50 / 60 Pression de l'arrivée d'eau Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 13 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.50 1) Reportez-vous à la plaque signalétique pour d'autres valeurs.
FRANÇAIS 47
156920210-A-262017 www.aeg.