FFB51400ZM USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
ENGLISH fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses. • Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.), let the water flow until it is clean and clear. • Ensure that there are no visible water leaks during and after the first use of the appliance. • The water inlet hose has a safety valve and a sheath with an inner mains cable. 5 2.
www.aeg.com 3.
ENGLISH 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Rinsing phase. It comes on when the rinsing phase operates. Drying phase. It comes on when the drying phase operates. End indicator. TimeSaver indicator. XtraDry indicator. Rinse aid indicator.
www.aeg.com Indicator Description Delay indicator. Door indicator. It comes on when the appliance door is open or is not correctly closed. 5. PROGRAMMES The numbering of the programmes in the table (P1, P2, etc.) reflects their sequence on the control panel. Programme 1) 2) 3) The order of the programmes in the table may not reflect their sequence on the control panel.
ENGLISH 9 5.1 Consumption values Programme 1) Water (l) Energy (kWh) Duration (min) 9.9 0.778 245 6 - 12 0.5 - 1.2 40 - 150 11 - 13 1.0 - 1.2 130 - 150 8 0.6 - 0.8 30 10 - 12 0.8 - 0.9 60 - 80 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes To receive the necessary information for conducting performance tests (e.g.
www.aeg.com The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area. It is important to set the right level of the water softener to assure good washing results.
ENGLISH How to deactivate the rinse aid empty notification Make sure the appliance is in user mode. 1. Press Start. • The indicators off. and are still • The indicator flashes. • The display shows the current setting. – = rinse aid empty notification activated. = rinse aid empty notification deactivated. 2. Press Start to change the setting. 3. Press on/off to confirm the setting. – 11 CAUTION! Do not try to close the appliance door within 2 minutes after automatic opening.
www.aeg.com Not all options are compatible with each other. If you select non compatible options, the appliance automatically deactivates one or more of them. Only the indicators of the still active options are on. If an option is not applicable to a programme, the related indicator is off or it flashes quickly for a few seconds and then goes out. Activating options can affect the water and energy consumption as well as the programme duration. 7.
ENGLISH How to fill the salt container 1. Turn the cap of the salt container counterclockwise and remove it. 2. Put 1 litre of water in the salt container (only for the first time). 3. Fill the salt container with 1 kg of salt (until it is full). 13 8.2 How to fill the rinse aid dispenser A DB M AX 4 1 3 2 + - C 4. Carefully shake the funnel by its handle to get the last granules inside. 5. Remove the salt around the opening of the salt container. 6.
www.aeg.com 9.1 Using the detergent A B 30 20 C 2. Press Program again and again until the indicator of the desired programme is on. The display shows the programme duration. 3. Set the applicable options. 4. Press Start to start the programme. • The indicator of the running phase is on. • The programme duration starts to decrease with steps of 1 minute. Starting a programme with delay start CAUTION! Only use detergent specifically designed for dishwashers. 1.
ENGLISH Do not try to close the appliance door within 2 minutes after AirDry automatically opens it, as this may cause damage to the appliance. If, afterwards, the door is closed for another 3 minutes, the running programme ends. Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again. 15 Make sure that there is detergent in the detergent dispenser before you start a new programme.
www.aeg.com 10.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5.
ENGLISH 17 C B A 1. Turn the filter (B) counterclockwise and remove it. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 4. Wash the filters.
www.aeg.com 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance.
ENGLISH 19 Problem and alarm code Possible cause and solution The appliance does not fill with water. • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the filter in the inlet hose is not clogged. • Make sure that the inlet hose has no kinks or bends. The display shows or . The appliance does not drain the water.
www.aeg.com Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes. Once you have checked the appliance, deactivate and activate the appliance. If the problem occurs again, contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre. 12.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results.
ENGLISH 21 Problem Possible cause and solution Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener". • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together. There are residues of detergent in the dispenser at the end of the programme. • The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
www.aeg.com Capacity Place settings 9 Power consumption Left-on mode (W) 5.0 Off-mode (W) 0.50 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to decrease energy consumption. 14. ENVIRONMENTAL CONCERNS Recycle materials with the symbol . Put the packaging in relevant containers to recycle it.
X X X Hydraulic circuit (including tanks)* Wiring harnesses * Hg Cd Cr6+ Hazardous substances PBBs PBDEs Note: 1. This table is compiled according to SJ/T11364-2014. means that this kind of hazardous substance content in all of the homogenous materials of this part is under the limitations 2. regulated in GB/T26572-2011. 3. X means that this kind of hazardous substance content in at least one homogenous material of this part exceeds the limitations regulated in GB/T26572-2011. 4.
156929540-A-142018 www.aeg.