FFB52600ZM EN FR DE USER MANUAL User Manual Dishwasher Notice d'utilisation Lave-vaisselle Benutzerinformation Geschirrspüler 2 24 48
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damage that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
ENGLISH • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse (UK and Ireland only). 2.3 Water connection • Do not cause damage to the water hoses. • Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.
www.aeg.com 3.
ENGLISH 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Rinsing phase. It comes on when the rinsing phase operates. Drying phase. It comes on when the drying phase operates. End indicator. TimeSaver indicator. XtraDry indicator. Rinse aid indicator.
www.aeg.com Indicator Description Delay indicator. Door indicator. It comes on when the appliance door is open or is not correctly closed. 5. PROGRAMMES The order of the programmes in the table may not reflect their sequence on the control panel.
ENGLISH 9 5.1 Consumption values Programme 1) Water (l) Energy (kWh) Duration (min) 9.9 0.920 237 6 - 12 0.6 - 1.5 44 - 160 14 - 15 1.5 - 1.7 155 - 171 10 0.8 30 13 - 14 1.0 - 1.1 75 - 85 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes To receive the necessary information for conducting performance tests (e.g.
www.aeg.com The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. Softening hard water increases the consumption of water and energy as well as the programme duration. The higher the level of water softener, the higher the consumption and the longer the duration. The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area.
ENGLISH only, it is possible to deactivate the notification for refilling rinse aid. However, for best drying performance, always use rinse aid. If standard detergent or multi-tablets without rinse aid are used, activate the notification to keep the rinse aid refill indicator active. How to deactivate the rinse aid empty notification 1. Press Start. and are • The indicator still flashes. • The display shows the current setting. – During the drying phase, the door opens automatically and remains ajar.
www.aeg.com 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. The Option button toggles between the available options and their possible combinations. Not all options are compatible with each other. If you select non compatible options, the appliance automatically deactivates one or more of them. Only the indicators of the still active options are on.
ENGLISH detergent and do not put dishes in the baskets. After starting the programme, the appliance recharges the resin in the water softener for up to 5 minutes. The washing phase starts only after this procedure is complete. The procedure is repeated periodically. 8.1 The salt container CAUTION! Use rough salt designed for dishwashers only. Fine salt increases the risk of corrosion. 13 CAUTION! Water and salt can come out of the salt container when you fill it.
www.aeg.com You can turn the selector of the released quantity (B) between position 1 (lowest quantity) and position 4 or 6 (highest quantity). 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5.
ENGLISH • The indicator of the running phase is on. • The programme duration starts to decrease with steps of 1 minute. Starting a programme with delay start 1. Set a programme. 2. Press Delay repeatedly until the display shows the desired delay time (from 1 to 24 hours). 3. Press Start to begin the countdown. • The indicator is on. • The remaining time counts down in hours. The final hour is displayed in minutes.
www.aeg.com 10. HINTS AND TIPS 10.1 General Follow the hints below to ensure optimal cleaning and drying results in daily use and to help you protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, select a programme with a prewash phase. • Always use the whole space of the baskets. • Make sure that items in the baskets do not touch or cover each other. Only then can the water completely reach and wash the dishes.
ENGLISH 10.5 Before starting a programme • The correct quantity of detergent is used. Before you start the selected programme, make sure that: 10.6 Unloading the baskets • The filters are clean and correctly installed. • The cap of the salt container is tight. • The spray arms are not clogged. • There is enough salt and rinse aid (unless you use multi-tablets). • The arrangement of the items in the baskets is correct. • The programme is suitable to the type of load and the degree of soil. 17 1.
www.aeg.com CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.3 External cleaning 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7.
ENGLISH solve the problem by yourself with the help of the information in the table or contact an Authorised Service Centre. WARNING! Repairs not properly done may result in serious risk to the safety of the user. Any repairs must be performed by qualified personnel. 19 With some problems, the display shows an alarm code. The majority of problems that can occur can be solved without the need to contact an Authorised Service Centre.
www.aeg.com Problem and alarm code Possible cause and solution The remaining time in the • This is not a defect. The appliance is working correctly. display increases and skips nearly to the end of program time. Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if applicable). The appliance door is difficult to close. • The appliance is not levelled.
ENGLISH 21 Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option XtraDry and set AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets.
www.aeg.com Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. The level of salt is low, check the refill indicator. The cap of the salt container is loose. Your tap water is hard.
ENGLISH 23 The ‘standard programme’ is the standard cleaning cycle to which the information in the label and the fiche relates. This programme is suitable to clean normally soiled tableware and is the most efficient programme in terms of combined energy and water consumption. It is indicated as "Eco" programme. Programme time of standard cleaning cycle (min) 237 Duration of the left-on mode (min) 5 Sound power level (db(A) re 1pW) 47 Built in appliance Y/N No 14.
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................25 2. CONSIGNES DE SÉCURITÉ......................................................................................26 3. DESCRIPTION DE L'APPAREIL.................................................................................28 4. BANDEAU DE COMMANDE....................................................................................29 5. PROGRAMMES....................
FRANÇAIS 1. 25 INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.1 Sécurité des enfants et des personnes vulnérables.
www.aeg.com bâtiments de ferme, cuisines réservées aux employés dans les magasins, bureaux et autres lieux de travail ; – pour une utilisation privée, par les clients, dans des hôtels et autres lieux de séjour. Ne modifiez pas les caractéristiques de cet appareil. La pression de l'eau en fonctionnement (minimale et maximale) doit se situer entre 0.5 (0.05) / 8 (0.8) bar (MPa) Respectez le nombre maximal de 13 couverts.
FRANÇAIS • Soyez toujours vigilants lorsque vous déplacez l'appareil car il est lourd. Utilisez toujours des gants de sécurité et des chaussures fermées. • N'installez pas l'appareil ou ne l'utilisez pas dans un endroit où la température ambiante est inférieure à 0 °C. • Installez l'appareil dans un lieu sûr et adapté répondant aux exigences d'installation. 2.2 Raccordement électrique AVERTISSEMENT! Risque d'incendie ou d'électrocution. • L’appareil doit être relié à la terre.
www.aeg.com pendant le déroulement d'un programme. 2.5 Maintenance • Pour réparer l'appareil, contactez un service après-vente agréé. • Utilisez exclusivement des pièces d'origine. • Débranchez l'appareil de l'alimentation électrique. • Coupez le câble d'alimentation et mettez-le au rebut. • Retirez le dispositif de verrouillage de la porte pour empêcher les enfants et les animaux de s'enfermer dans l'appareil. 2.6 Mise au rebut AVERTISSEMENT! Risque de blessure ou d'asphyxie. 3.
FRANÇAIS 4. BANDEAU DE COMMANDE 1 2 8 1 2 3 4 5 Touche Marche/Arrêt Touche Program Voyants de programme Affichage Touche Delay 3 4 7 5 6 6 Touche Option 7 Voyants 8 Touche Start 4.1 Voyants Indicateur Description Phase de lavage. Il s'allume au cours de la phase de lavage. Phase de rinçage. Il s'allume au cours de la phase de rinçage. Phase de séchage. Il s'allume au cours de la phase de séchage. Voyant de fin. Voyant TimeSaver. Voyant XtraDry. Voyant du réservoir de liquide de rinçage.
www.aeg.com Indicateur Description Voyant Delay. Voyant de porte. Il s'allume lorsque la porte de l'appareil est ouverte ou mal fermée. 5. PROGRAMMES Le numéro des programmes indiqué dans le tableau peut ne pas Programme 1) 2) 3) correspondre à leur ordre sur le bandeau de commande.
FRANÇAIS 31 5.1 Valeurs de consommation Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 9.9 0.920 237 6 - 12 0.6 - 1.5 44 - 160 14 - 15 1.5 - 1.7 155 - 171 10 0.8 30 13 - 14 1.0 - 1.1 75 - 85 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.com Comment entrer en mode utilisateur L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région. Il est important de régler l'adoucisseur d'eau sur un niveau adéquat pour vous garantir de bons résultats de lavage. Assurez-vous que l'appareil est en mode Programmation.
FRANÇAIS Comment régler le niveau de l'adoucisseur d'eau • Les voyants éteints. Assurez-vous que l'appareil est en mode Utilisateur. • Le voyant clignote toujours. • L'affichage indique le réglage actuel. 1. Appuyez sur Program. • Les voyants éteints. et sont clignote • Le voyant toujours. • L'affichage indique le réglage actuel : Par ex., = niveau 5. 2. Appuyez sur la touche Program plusieurs fois pour modifier le réglage. 3. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.
www.aeg.com ATTENTION! Si les enfants peuvent accéder à l'appareil, nous vous conseillons de désactiver l'option AirDry car l'ouverture de la porte pourrait présenter un danger. Comment désactiver l'option AirDry 1. Appuyez sur Delay. • Les voyants sont éteints. et • Le voyant clignote toujours. • L'affichage indique le réglage actuel : = AirDry activé. 2. Appuyez sur la touche Delay pour modifier le réglage : = AirDry désactivé. 3. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage.
FRANÇAIS Comment activer l'option XtraDry 35 Appuyez sur la touche Option jusqu'à ce Les résultats de lavage seront les mêmes qu'avec la durée normale du programme. Les résultats de séchage peuvent être moins satisfaisants. que le voyant s'allume. L'affichage indique la durée du programme réactualisée. Comment activer l'option TimeSaver 7.2 TimeSaver Appuyez sur la touche Option jusqu'à ce Cette option augmente la pression et la température de l'eau.
www.aeg.com B A M AX 4 6. Tournez le couvercle du réservoir de sel régénérant vers la droite pour le refermer. ATTENTION! De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Afin d'éviter la corrosion, lancez immédiatement un programme après avoir rempli le réservoir de sel régénérant. 8.
FRANÇAIS 9.1 Utilisation du produit de lavage Cette fonction réduit la consommation d'énergie en éteignant automatiquement l'appareil lorsqu'il ne fonctionne pas. 30 20 La fonction s'active : • 5 minutes après la fin du programme de lavage. • Au bout de 5 minutes si le programme n'a pas démarré. C B 30 9.
www.aeg.com Lorsque le décompte est terminé, le programme démarre et le voyant de la phase en cours s'allume. Le voyant est éteint. Ouverture de la porte au cours du fonctionnement de l'appareil Si vous ouvrez la porte lorsqu'un programme est en cours, l'appareil s'arrête. Cela peut avoir un impact sur la consommation d'énergie et la durée du programme. Lorsque vous refermez la porte, l'appareil reprend là où il a été interrompu.
FRANÇAIS 10.2 Utilisation de sel régénérant, de liquide de rinçage et de produit de lavage • Utilisez uniquement du sel régénérant, du liquide de rinçage et du produit de lavage conçus pour les lave-vaisselle. D'autres produits peuvent endommager l'appareil.
www.aeg.com • Le programme est adapté au type de vaisselle et au degré de salissure. • Vous utilisez la bonne quantité de produit de lavage. vaisselle encore chaude est sensible aux chocs. 2. Commencez par décharger le panier inférieur, puis le panier supérieur. Une fois le programme terminé, il peut rester de l'eau sur les surfaces intérieures de l'appareil. 10.6 Déchargement des paniers 1. Attendez que la vaisselle refroidisse avant de la retirer de l'appareil. La 11.
FRANÇAIS 41 ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d'aspersion. Si des résidus ont bouché les orifices des bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat (A) en place.
www.aeg.com 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'il s'arrête en cours de fonctionnement, vérifiez d'abord si vous pouvez résoudre le problème par vous-même en vous aidant des informations du tableau ou contactez le Service après-vente agréé. Pour certaines anomalies, l'écran affiche un code d'alarme. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé.
FRANÇAIS 43 Problème et code d'alarme Cause et solution possibles Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Fermez le robinet d'eau et contactez le service aprèsvente agréé. . L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps. • Sélectionnez l'option TimeSaver pour raccourcir la durée du programme.
www.aeg.com 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
FRANÇAIS 45 Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage pour lavevaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après-vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble.
www.aeg.com 13. FICHE PRODUIT Marque AEG Modèle FFB52600ZM 911514009 Capacité nominale (nombre de couverts standard) 13 Classe d’efficacité énergétique A++ Consommation d'énergie en kWh par an, basée sur 262 280 cycles de lavage standard utilisant de l'eau froide et les modes de basse consommation énergétique. La consommation énergétique réelle dépendra de l'utilisation de l'appareil. Consommation d’énergie du cycle de lavage standard (kWh) 0.
FRANÇAIS Tension (V) 220 - 240 Fréquence (Hz) 50 Pression de l'arrivée d'eau Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Branchement électrique 1) 47 1) Reportez-vous à la plaque signalétique pour d'autres valeurs. 2) Si l'eau chaude est produite à partir de sources d'énergie respectueuses de l'environnement (par exemple panneaux solaires), utilisez une arrivée d'eau chaude afin de réduire la consommation d'énergie. 15.
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE........................................................................................... 49 2. SICHERHEITSANWEISUNGEN.................................................................................51 3. PRODUKTBESCHREIBUNG...................................................................................... 52 4. BEDIENFELD..............................................................................................................53 5.
DEUTSCH 1. 49 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Bedienungsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung zum Nachschlagen an einem sicheren und zugänglichen Ort auf. 1.
www.aeg.com Bauernhöfe, Personalküchenbereiche in Geschäften, Büros und anderen Arbeitsumfeldern. – Für Gäste in Hotels, Motels, Pensionen und anderen wohnungsähnlichen Räumlichkeiten. Nehmen Sie keine technischen Änderungen am Gerät vor. Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt.
DEUTSCH 51 2. SICHERHEITSANWEISUNGEN 2.1 Montage WARNUNG! Die Montage des Geräts darf nur von einer qualifizierten Fachkraft durchgeführt werden. • Entfernen Sie das gesamte Verpackungsmaterial. • Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. • Halten Sie sich an die mitgelieferte Montageanleitung. • Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk.
www.aeg.com des Wasserzulaufschlauchs an den autorisierten Kundendienst. 2.4 Gebrauch • Laden Sie keine entflammbaren Produkte oder Gegenstände, die mit entflammbaren Produkten benetzt sind, in das Gerät und stellen Sie solche nicht in die Nähe oder auf das Gerät. • Geschirrspüler-Reinigungsmittel sind gefährlich. Beachten Sie die Sicherheitsanweisungen auf der Reinigungsmittelverpackung. • Trinken Sie nicht das Wasser aus dem Gerät und verwenden Sie es nicht zum Spielen.
DEUTSCH 5 6 7 8 9 Typenschild Salzbehälter Entlüftung Klarspülmittel-Dosierer Reinigungsmittelfach 10 Besteckkorb 11 Unterkorb 12 Oberkorb 4. BEDIENFELD 1 2 8 1 2 3 4 5 3 4 7 Taste „Ein/Aus“ Taste Program Programmkontrolllampen Display Taste Delay 5 6 6 Taste Option 7 Kontrolllampen 8 Taste Start 4.1 Kontrolllampen Kontrolllampe Beschreibung Hauptspülgang. Leuchtet während des Hauptspülgangs auf. Spülgang. Leuchtet während der Spülphase auf. Trockenphase.
www.aeg.com Kontrolllampe Beschreibung Kontrolllampe TimeSaver. Kontrolllampe XtraDry. Kontrolllampe Klarspülmittel. Sie erlischt während des Programmbetriebs. Kontrolllampe Salz. Sie erlischt während des Programmbetriebs. Kontrolllampe Delay. Kontrolllampe Tür. Leuchtet, wenn die Tür des Geräts offen oder nicht richtig geschlossen ist. 5.
DEUTSCH Programm Verschmutzungsgrad Beladung Programmphasen Optionen • Normaler oder leichter Verschmutzungsgrad • Empfindliches Geschirr und Gläser • Hauptspülgang 45 °C • Spülen • Trocknen • XtraDry 55 1) Dieses Programm gewährleistet den wirtschaftlichsten Wasser- und Energieverbrauch für normal verschmutztes Geschirr und Besteck. Dies ist das Standardprogramm für Prüfinstitute. 2) Das Gerät erkennt den Verschmutzungsgrad und die Anzahl der Geschirrteile in den Körben.
www.aeg.com 6. EINSTELLUNGEN 6.1 Programmwahlmodus und Benutzermodus Wenn sich das Gerät im Programmwahlmodus befindet, kann ein Programm eingestellt und der Benutzermodus aufgerufen werden. Einstellungen, die im Benutzermodus verfügbar sind: • Die Stufe des Wasserenthärters gemäß der Wasserhärte. • Ein- und Ausschalten der Klarspülmittelnachfüllanzeige.
DEUTSCH 57 Deutsche Wasserhärtegrade (°dH) Französische Wasserhärtegrade (°fH) mmol / l Clarke Wasserhärtegrade Einstellung des Wasserenthärters 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Werkseitige Einstellung.
www.aeg.com Ausschalten der Klarspülmittelnachfüllanzeige Stellen Sie sicher, dass sich das Gerät im Benutzermodus befindet. 1. Drücken Sie Start. • Die Kontrolllampen und erlöschen. • Die Kontrolllampe blinkt weiterhin. • Im Display wird die aktuelle Einstellung angezeigt. – = Klarspülmittelnachfüllanzeige eingeschaltet. – = Klarspülmittelnachfüllanzeige ausgeschaltet. 2. Drücken Sie Start zum Ändern der Einstellung. 3. Drücken Sie Ein/Aus zum Bestätigen der Einstellung.
DEUTSCH 59 7. OPTIONEN Sie müssen die gewünschten Optionen vor dem Programmstart einschalten. Es ist nicht möglich, Optionen während eines laufenden Programms einoder auszuschalten. Die Option-Taste schaltet zwischen den verfügbaren Optionen und den möglichen Kombinationen um. Die Option XtraDry bleibt permanent für alle Programme außer für eingeschaltet und muss nicht mit jedem Programm erneut ausgewählt werden.
www.aeg.com 8. VOR DER ERSTEN INBETRIEBNAHME 1. Prüfen Sie, ob die Einstellung des Wasserenthärters der Wasserhärte in Ihrem Gebiet entspricht. Wenn nicht, stellen Sie die Wasserenthärterstufe ein. 2. Füllen Sie den Salzbehälter. 3. Füllen Sie den KlarspülmittelDosierer. 4. Öffnen Sie den Wasserzulaufhahn. 5. Starten Sie ein Programm, um Fertigungsrückstände, die sich möglicherweise noch im Gerät befinden können, zu beseitigen. Verwenden Sie kein Reinigungsmittel und beladen Sie die Körbe nicht.
DEUTSCH 8.2 Füllen des KlarspülmittelDosierers A D B C B A 4 1 3 2 VORSICHT! Verwenden Sie ausschließlich Klarspülmittel für Geschirrspüler. 1. Drücken Sie die Entriegelungstaste (D), um den Deckel (C) zu öffnen. 2. Füllen Sie den Dosierer (A) mit Klarspülmittel bis zur Marke „MAX“. 3. Wischen Sie verschüttetes Klarspülmittel mit einem saugfähigen Tuch auf, um zu große Schaumbildung zu vermeiden. 4. Schließen Sie den Deckel. Achten Sie darauf, dass die Entriegelungstaste einrastet.
www.aeg.com B A 30 D 20 C VORSICHT! Verwenden Sie nur Reinigungsmittel für Geschirrspüler. 1. Drücken Sie die Entriegelungstaste (B), um den Deckel (C) zu öffnen. 2. Füllen Sie das Reinigungsmittel ein oder legen Sie eine Reinigungstablette in das Fach (A). 3. Wenn das Programm einen Vorspülgang hat, füllen Sie eine kleine Menge Reinigungsmittel in das Fach (D). 4. Schließen Sie den Deckel. Achten Sie darauf, dass die Entriegelungstaste einrastet. 9.
DEUTSCH Versuchen Sie nicht, die Gerätetür innerhalb der ersten 2 Minuten nach der automatischen Öffnung durch AirDry zu schließen, da das Gerät beschädigt werden könnte. Wird die Tür danach für weitere 3 Minuten geschlossen, wird das laufende Programm beendet. Abbrechen einer eingestellten Zeitvorwahl während des Countdowns Wenn Sie die eingestellte Zeitvorwahl abbrechen, müssen das Programm und die Optionen erneut eingestellt werden.
www.aeg.com Reinigungsmittel-Rückstände auf dem Geschirr zurückbleiben. • Verwenden Sie nicht mehr als die angegebene Reinigungsmittelmenge. Siehe hierzu die Angaben auf der Reinigungsmittelverpackung. 10.3 Was tun, wenn Sie keine Multi-Reinigungstabletten mehr verwenden möchten Vorgehensweise, um zur separaten Verwendung von Reinigungsmittel, Salz und Klarspülmittel zurückzukehren: 1. Stellen Sie die höchste Wasserenthärterstufe ein. 2.
DEUTSCH 65 11. REINIGUNG UND PFLEGE WARNUNG! Schalten Sie das Gerät immer aus und ziehen Sie den Netzstecker aus der Steckdose, bevor Reinigungsarbeiten durchgeführt werden. Verschmutzte Filter und verstopfte Sprüharme beeinträchtigen das Spülergebnis. Prüfen Sie die Filter regelmäßig und reinigen Sie diese, falls nötig. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 11.1 Reinigen der Filter Das Filtersystem besteht aus 3 Teilen. 4. Reinigen Sie die Filter.
www.aeg.com sind, reinigen Sie sie mit einem dünnen spitzen Gegenstand. 11.3 Reinigen der Außenseiten • Reinigen Sie das Gerät mit einem weichen, feuchten Tuch. • Verwenden Sie ausschließlich Neutralreiniger. • Benutzen Sie keine Scheuermittel, scheuernde Reinigungsschwämmchen oder Lösungsmittel. 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet.
DEUTSCH Bei manchen Störungen zeigt das Display einen Alarmcode an. 67 der autorisierte Kundendienst gerufen werden muss. Die meisten Störungen, die auftreten, können behoben werden, ohne dass Störung und Alarmcode Mögliche Ursache und Abhilfe Das Gerät lässt sich nicht einschalten. • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. Das Programm startet nicht.
www.aeg.com Störung und Alarmcode Mögliche Ursache und Abhilfe Die verbleibende Zeit im Display erhöht sich und springt bis kurz vor die Programmende-Zeit. • Dies ist keine Störung. Das Gerät arbeitet ordnungsgemäß. Aus der Gerätetür tritt ein wenig Wasser aus. • Das Gerät ist nicht ausgerichtet. Schrauben Sie die Schraubfüße weiter hinein oder weiter heraus (falls vorhanden). • Die Gerätetür ist nicht mittig zur Wanne positioniert. Stellen Sie den hinteren Fuß ein (sofern vorhanden).
DEUTSCH 69 Störung Mögliche Ursache und Abhilfe Nicht zufriedenstellende Trocknungsergebnisse. • Das Geschirr stand zu lange im geschlossenen Gerät. • Es ist kein Klarspülmittel vorhanden oder die Klarspülmittelmenge ist nicht ausreichend. Stellen Sie den Klarspülmittel-Dosierer auf eine höhere Einstellung. • Kunststoffteile müssen eventuell mit einem Tuch abgetrocknet werden. • Schalten Sie die Option XtraDry ein, und stellen Sie AirDry ein, um die beste Trocknungsleistung zu erzielen.
www.aeg.com Störung Mögliche Ursache und Abhilfe Am Ende des Programms befinden sich Reinigungsmittelreste im Behälter. • Das Reinigungsmittel-Tab blieb im Behälter stecken und wurde daher nicht vollständig vom Wasser mitgenommen. • Das Wasser kann das Reinigungsmittel nicht aus dem Behälter ausspülen. Achten Sie darauf, dass der Sprüharm nicht blockiert oder verstopft ist. • Stellen Sie sicher, dass die im Korb eingeordneten Gegenstände ein Öffnen des Reinigungsmittelbehälters nicht verhindern.
DEUTSCH 71 Energieverbrauch in kWh pro Jahr, basierend auf 280 262 Stanard-Reinigungszyklen bei Verwendung von kaltem Wasser und der Modi mit wenig Energiebedarf. Der tatsächliche Verbrauch hängt davon ab, wie das Gerät verwendet wird. Energieverbrauch des Standard-Reinigungs-Zyklus in kWh 0.920 Energieverbrauch im OFF-Modus in W 0.50 Energieverbauch im nicht-ausgeschalteten Zustand in W 5.0 Wasserverbrauch in Liter/Jahr, auf der Grundlage von 2775 280 Standardreinigungszyklen.
www.aeg.com 15. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte. Entsorgen Sie * Geräte mit diesem Symbol nicht mit dem Hausmüll. Bringen Sie das Gerät zu Ihrer örtlichen Sammelstelle oder wenden Sie sich an Ihr Gemeindeamt.
DEUTSCH 73
www.aeg.
DEUTSCH 75
156915221-A-242019 www.aeg.