FFB53600ZM FFB53600ZW NL EN FR USER MANUAL Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 24 44
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE......................................................................................... 3 2. VEILIGHEIDSVOORSCHRIFTEN.................................................................................4 3. BESCHRIJVING VAN HET PRODUCT........................................................................6 4. BEDIENINGSPANEEL................................................................................................. 7 5. PROGRAMMA’S..................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • • Als de voedingskabel beschadigd is, moet de fabrikant, een erkende serviceverlener of een gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt.
NEDERLANDS • Alleen voor VK en Ierland. Het apparaat heeft een stekker van 13 ampère. Als de zekering van de stekker verwisseld moet worden, gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Beschadig de waterslangen niet. • Indien buizen lang niet zijn gebruikt, er reparaties hebben plaatsgevonden of er nieuwe apparaten zijn geplaatst (watermeters, enz.), moet u, voordat de nieuwe buizen worden aangesloten, het water laten stromen tot het schoon en helder is.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 3 8 1 2 3 4 5 Aan/uit-toets Program-toets Programma-indicatielampjes Weergave Delay-toets 4 7 5 6 6 Option-toets 7 Indicatielampjes 8 Start-toets 4.1 Indicatielampjes Aanduiding Beschrijving Wasfase. Gaat aan wanneer de wasfase loopt. Spoelfase. Gaat aan wanneer de spoelfase loopt. Droogfase. Gaat aan wanneer de droogfase loopt. Einde-indicatielampje. TimeSaver-indicatielampje. XtraDry-indicatielampje. Glansmiddelindicatielampje.
www.aeg.com Aanduiding Beschrijving Delay-indicatielampje. Deur-indicatielampje. Gaat aan als de deur niet goed is geopend of gesloten. 5.
NEDERLANDS 9 5.1 Verbruiksgegevens Programma 1) Water (l) Energie (kWh) Programmaduur (min.) 9,9 0.832 240 7 - 12 0.7 - 1.5 45 - 160 13 - 15 1.4 - 1.6 140 - 160 9 0.8 30 13 - 14 0.9 - 1.1 70 - 85 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.
www.aeg.com Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
NEDERLANDS 11 droogresultaten altijd glansmiddel te gebruiken. Schakel de aanduiding in om de glansmiddelindicator actief te houden als u standaard wasmiddel of multitabletten zonder glansmiddel bevat. Het uitschakelen van de melding van een leeg glansmiddeldoseerbakje Het apparaat moet in de programmakeuzemodus staan. Tijdens de werking van de droogfase, wordt de deur van het apparaat door een instrument geopend. De deur blijft op een kier. 1.
www.aeg.com 3. Druk op Delay om de instelling te wijzigen: = AirDry uitgeschakeld. 4. Druk op de knop aan/uit om de instelling te bevestigen. 7. OPTIES De gewenste opties moeten elke keer dat u een programma start worden geactiveerd. De opties kunnen niet worden in- of uitgeschakeld als een programma in werking is. Niet alle opties kunnen met elkaar worden gecombineerd.
NEDERLANDS apparaat zijn achtergebleven. Gebruik geen afwasmiddel en gebruik de mandjes niet. Als u een programma start, doet het apparaat er ongeveer 5 minuten over om de hars in de waterontharder te herladen. Het lijkt alsof het apparaat niet werkt. De wasfase start pas nadat deze procedure voltooid is. De procedure wordt periodiek herhaald. 8.1 Het zoutreservoir LET OP! Gebruik uitsluitend zout dat specifiek is bedoeld voor gebruik in vaatwassers.
www.aeg.com 4. Sluit het deksel. Zorg ervoor dat het ontgrendelknopje op zijn plaats dichtklikt. U kunt het schuifje voor de vrij te geven hoeveelheid (B) instellen tussen stand 1 (laagste hoeveelheid) en stand 4 of 6 (hoogste hoeveelheid). 9. DAGELIJKS GEBRUIK 1. Draai de waterkraan open. 2. Druk op de aan-/uittoets om het apparaat te activeren. Zorg dat het apparaat in de programmakeuzemodus staat. • Vul het zoutreservoir als het zoutindicatielampje brandt.
NEDERLANDS 3. Stel de bruikbare opties in. 4. Druk op Start om het programma te starten. • Het indicatielampje van de lopende fase gaat aan. • De programmaduur neemt af in stappen van 1 minuut. Een programma starten met een uitgestelde start 1. Stel een programma in. 2. Blijf op Delay drukken tot het display de uitgestelde tijd toont die u wilt instellen (van 1 tot 24 uur). 3. Druk op Start om het aftellen te starten.
www.aeg.com • Zorg er bij het inladen van het apparaat voor dat de vaat helemaal kan worden bereikt en gewassen door het water uit de sproeiarmen. Zorg ervoor dat de vaat elkaar niet raakt of overlapt. • U kunt apart vaatwasmiddel, glansmiddel en zout gebruiken of kiezen voor het gebruik van multitabletten (bijv. ''3in1'', ''4in1'', ''All in 1''). Volg de aanwijzing op de verpakking. • U dient het juiste programma in te stellen voor het type lading en de mate van vervuiling.
NEDERLANDS • Er regenereerzout en glansmiddel is toegevoegd (tenzij u gecombineerde afwastabletten gebruikt). • De positie van de items in de mandjes correct is. • Het programma van toepassing is op het type lading en de mate van bevuiling. • De juiste hoeveelheid afwasmiddel is gebruikt. 17 borden zijn gevoelig voor beschadigingen. 2. Ruim eerst het onderrek en dan het bovenrek uit. Aan het einde van het programma kan er water aan de zijkanten en de deur van het apparaat achterblijven. 10.
www.aeg.com LET OP! Een onjuiste plaatsing van de filters kan leiden tot slechte wasresultaten en het apparaat beschadigen. 11.2 De sproeiarmen reinigen Probeer niet de sproeiarmen te verwijderen. Als etensresten de openingen in de sproeiarmen hebben verstopt, verwijder deze dan met een smal en puntig voorwerp. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter terug (A). Zorg ervoor dat het goed onder de 2 geleidingen zit. 11.
NEDERLANDS 19 12. PROBLEEMOPLOSSING Het apparaat start of stopt niet tijdens de werking. Kijk voordat u contact opneemt met de klantenservice of u het probleem zelf kunt oplossen met behulp van de informatie in de tabel. WAARSCHUWING! Niet juist uitgevoerde reparaties kunnen de veiligheid van de gebruiker ernstig in gevaar brengen. Alle reparaties moeten worden uitgevoerd door bevoegd personeel. Bij sommige problemen wordt er op de display een alarmcode weergegeven.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing Het apparaat stopt en start meerdere keren tijdens de werking. • Dat is normaal. Het voorziet in optimale reinigingsresultaten en energiebesparing. Het programma duurt te lang. • Kies de optie TimeSaver om de programmaduur te verkorten. • Als de optie uitgestelde start is ingesteld, annuleert u deze functie of wacht u tot het aftellen is voltooid.
NEDERLANDS 21 12.1 De was- en droogresultaten zijn niet naar tevredenheid Probleem Mogelijke oorzaak en oplossing Slechte wasresultaten. • Raadpleeg "Dagelijks gebruik", "Aanwijzingen en tips" en de folder voor het laden van de korf. • Gebruik intensievere wasprogramma´s. • Maak de inspuiters van de sproeiarm en het filter schoon. Zie "Onderhoud en reiniging". Slechte droogresultaten. • Serviesgoed heeft te lang in het gesloten apparaat gestaan.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Roestresten op bestek. • Er wordt voor het wassen teveel zout in het water gebruikt. Zie 'De waterontharder instellen'. • Zilver en roestvrijstalen bestek zijn samen geplaatst. Zet zilveren en roestvrijstalen voorwerpen niet dicht bij elkaar. Er bevinden zich aan het einde • De vaatwastablet raakte klem in het vaatwasmiddeldovan het programma resten van seerbakje en is daardoor niet volledig weggespoeld vaatwasmiddel in het vaatwasdoor het water.
NEDERLANDS Watertoevoerdruk Min. / max. bar (MPa) Watertoevoer Koud water of warm water2) max. 60 °C Vermogen Couverts 13 Energieverbruik Modus aan laten (W) 5.0 Energieverbruik Uit-modus (W) 0.10 23 0.5 (0.05) / 8 (0.8) 1) Zie het typeplaatje voor andere waarden. 2) Als het hete water door alternatieve, milieuvriendelijkere energiebronnen geproduceerd wordt (bijv. zonnepanelen en windenergie), gebruik dan een heetwatervoorziening om het energieverbruik te verminderen. 14.
www.aeg.com CONTENTS 1. SAFETY INFORMATION........................................................................................... 25 2. SAFETY INSTRUCTIONS...........................................................................................26 3. PRODUCT DESCRIPTION.........................................................................................27 4. CONTROL PANEL..................................................................................................... 28 5. PROGRAMMES......
ENGLISH 1. 25 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
ENGLISH • The water inlet hose has a safety valve and a sheath with an inner mains cable. • • • • WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging.
www.aeg.com 3 4 5 6 7 8 Lower spray arm Filters Rating plate Salt container Air vent Rinse aid dispenser 9 10 11 12 Detergent dispenser Cutlery basket Lower basket Upper basket 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Rinsing phase. It comes on when the rinsing phase operates.
ENGLISH Indicator 29 Description TimeSaver indicator. XtraDry indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. Delay indicator. Door indicator. It comes on when the appliance door is open or is not correctly closed. 5.
www.aeg.com 5.1 Consumption values Programme 1) Water (l) Energy (kWh) Duration (min) 9.9 0.832 240 7 - 12 0.7 - 1.5 45 - 160 13 - 15 1.4 - 1.6 140 - 160 9 0.8 30 13 - 14 0.9 - 1.1 70 - 85 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes For all the necessary information for test performance, send an email to: info.test@dishwasher-production.
ENGLISH 31 Water hardness German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
www.aeg.com notification to keep the rinse aid refill indicator active. While the drying phase operates, a device opens the appliance door. The door is then kept ajar. How to deactivate the rinse aid empty notification The appliance must be in programme selection mode. 1. To enter the user mode, press and hold simultaneously Delay and Option until the indicators , and start to flash and the display is blank. 2. Press Start. • The indicators off. and go • The indicator continues to flash.
ENGLISH 33 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you have selected non compatible options, the appliance will automatically deactivate one or more of them. Only the indicators of the options still active will stay on. How to activate XtraDry Press Option until the indicator comes on.
www.aeg.com 8.1 The salt container CAUTION! Only use salt specifically designed for dishwashers. 8.2 How to fill the rinse aid dispenser A D B The salt is used to recharge the resin in the water softener and to assure good washing results in the daily use. How to fill the salt container 1. Turn the cap of the salt container counterclockwise and remove it. 2. Put 1 litre of water in the salt container (Only for the first time). 3. Fill the salt container with dishwasher salt.
ENGLISH Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil. 9.1 Using the detergent D A B 35 9.
www.aeg.com Opening the door while the appliance operates If you open the door while a programme is running, the appliance stops. It may affect the energy consumption and the programme duration. When you close the door, the appliance continues from the point of interruption. If the door is opened for more than 30 seconds during the drying phase, the running programme ends. This does not happen if the door is opened by AirDry function.
ENGLISH 10.2 Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance. • In areas with hard and very hard water we recommend to use plain dishwasher detergent (powder, gel, tablets containing no additional agents), rinse aid and salt separately for optimal cleaning and drying results. • At least once a month run the appliance with the use of appliance cleaner which is particularly suitable for this purpose.
www.aeg.com 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. 4. Wash the filters. 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A).
ENGLISH 39 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 11.4 Internal cleaning CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object.
www.aeg.com Problem and alarm code Possible cause and solution The program does not start. • Make sure that the appliance door is closed. • Press Start. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to recharge the resin inside the water softener. The duration of the procedure is approximately 5 minutes. The appliance does not fill with water. • Make sure that the water tap is open.
ENGLISH 41 Problem and alarm code Possible cause and solution The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use. • Internal electrical fault of the appliance. Contact an Authorised Service Centre. Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes.
www.aeg.com Problem Possible cause and solution The dishes are wet. • For the best drying performance activate the option XtraDry and set AirDry . • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together.
ENGLISH 43 Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. 13. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 600 / 850 / 625 Electrical connection 1) Voltage (V) 200 - 240 Frequency (Hz) 50 / 60 Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 5.0 Power consumption Off-mode (W) 0.
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................45 2. CONSIGNES DE SÉCURITÉ......................................................................................46 3. DESCRIPTION DE L'APPAREIL.................................................................................48 4. BANDEAU DE COMMANDE....................................................................................49 5. PROGRAMMES....................
FRANÇAIS 1. 45 INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximal de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant d'installer des tuyaux neufs, des tuyaux n'ayant pas servi depuis longtemps, lorsqu'une réparation a été effectuée ou qu'un nouveau dispositif a été installé (compteurs d'eau, etc.), laissez l'eau s'écouler jusqu'à ce qu'elle soit parfaitement propre et claire.
www.aeg.com 3.
FRANÇAIS 4. BANDEAU DE COMMANDE 1 2 8 1 2 3 4 5 Touche Marche/Arrêt Touche Program Voyants de programme Affichage Touche Delay 3 4 7 5 6 6 Touche Option 7 Voyants 8 Touche Start 4.1 Voyants Indicateur Description Phase de lavage. Il s'allume au cours de la phase de lavage. Phase de rinçage. Il s'allume au cours de la phase de rinçage. Phase de séchage. Il s'allume au cours de la phase de séchage. Voyant de fin. Voyant TimeSaver. Voyant XtraDry. Voyant du réservoir de liquide de rinçage.
www.aeg.com Indicateur Description Voyant Delay. Voyant de porte. Il s'allume lorsque la porte de l'appareil est ouverte ou mal fermée. 5.
FRANÇAIS 51 5.1 Valeurs de consommation Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 9.9 0.832 240 7 - 12 0.7 - 1.5 45 - 160 13 - 15 1.4 - 1.6 140 - 160 9 0.8 30 13 - 14 0.9 - 1.1 70 - 85 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.com Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région. Il est important de régler l'adoucisseur d'eau sur un niveau adéquat pour vous garantir de bons résultats de lavage.
FRANÇAIS Le liquide de rinçage est automatiquement ajouté au cours de la phase de rinçage chaud. Notification du réservoir de liquide de rinçage vide Le liquide de rinçage permet à la vaisselle de sécher sans traces ni taches. Le liquide de rinçage est automatiquement libéré au cours de la phase de rinçage chaud. – = notification du distributeur de liquide de rinçage vide désactivée. 3. Appuyez sur Start pour modifier le réglage. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.
www.aeg.com 1. Pour entrer en mode utilisateur, maintenez les touches Delay et Option enfoncées jusqu'à ce que les , et se voyants mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur Delay. • Les voyants s'éteignent. et • Le voyant continue à clignoter. • L'affichage indique le réglage actuel : = AirDry activé. 3. Appuyez sur la touche Delay pour modifier le réglage : = AirDry désactivé. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 7.
FRANÇAIS 55 8. AVANT LA PREMIÈRE UTILISATION 1. Assurez-vous que le réglage actuel de l'adoucisseur d'eau est compatible avec la dureté de l'arrivée d'eau. Si ce n'est pas le cas, réglez le niveau de l'adoucisseur d'eau. 2. Remplissez le réservoir de sel régénérant. 3. Remplissez le distributeur de liquide de rinçage. 4. Ouvrez le robinet d'eau. 5. Lancez un programme pour éliminer tous les résidus qui peuvent toujours se trouver à l'intérieur de l'appareil.
www.aeg.com 8.2 Comment remplir le distributeur de liquide de rinçage A D ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. B C B A 1. Appuyez sur le bouton d'ouverture (D) pour ouvrir le couvercle (C). 2. Versez le liquide de rinçage dans le distributeur (A) jusqu'à ce qu'il atteigne le niveau « max ». 3. Si le liquide de rinçage déborde, épongez-le avec un chiffon absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle.
FRANÇAIS B A 30 D 20 C ATTENTION! Utilisez uniquement du produit de lavage spécifiquement conçu pour les lave-vaisselle. 1. Appuyez sur le bouton d'ouverture (B) pour ouvrir le couvercle (C). 2. Versez le produit de lavage, en poudre ou en pastilles, dans le compartiment (A). 3. Si le programme comporte une phase de prélavage, versez une petite quantité de produit de lavage dans le compartiment (D). 4. Fermez le couvercle. Assurez-vous que le bouton d'ouverture se verrouille correctement. 9.
www.aeg.com Durant la phase de séchage, si la porte est ouverte pendant plus de 30 secondes, le programme en cours s'arrête. Ceci ne se produit pas si la porte est ouverte par la fonction AirDry. Ne tentez pas de refermer la porte dans les 2 minutes suivant son ouverture automatique par la fonction AirDry car vous pourriez endommager l'appareil. Si par la suite vous refermez la porte pendant 3 minutes, le programme en cours se termine.
FRANÇAIS 10.2 Utilisation de sel régénérant, de liquide de rinçage et de produit de lavage • Utilisez uniquement du sel régénérant, du liquide de rinçage et du produit de lavage conçus pour les lave-vaisselle. D'autres produits peuvent endommager l'appareil.
www.aeg.com • Le programme est adapté au type de vaisselle et au degré de salissure. • Vous utilisez la bonne quantité de produit de lavage. vaisselle encore chaude est sensible aux chocs. 2. Commencez par décharger le panier inférieur, puis le panier supérieur. À la fin du programme, il peut rester de l'eau sur les parois et la porte de l'appareil. 10.6 Déchargement des paniers 1. Attendez que la vaisselle refroidisse avant de la retirer de l'appareil. La 11.
FRANÇAIS 61 ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d'aspersion. Si des résidus ont bouché les orifices des bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat (A) en place.
www.aeg.com 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'arrête en cours de programme. Avant de contacter le service après-vente agréé, vérifiez si vous pouvez résoudre le problème par vous-même à l'aide des informations du tableau. Pour certaines anomalies, l'écran affiche un code d'alarme. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé.
FRANÇAIS 63 Problème et code d'alarme Cause et solution possibles Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Fermez le robinet d'eau et contactez le service aprèsvente agréé. . L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps. • Sélectionnez l'option TimeSaver pour raccourcir la durée du programme.
www.aeg.com 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
FRANÇAIS 65 Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage pour lavevaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble.
www.aeg.com 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 600 / 850 / 625 Branchement électrique 1) Tension (V) 200 - 240 Fréquence (Hz) 50 / 60 Pression de l'arrivée d'eau Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 13 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.10 1) Reportez-vous à la plaque signalétique pour d'autres valeurs.
FRANÇAIS 67
156910911-A-442016 www.aeg.