FFB62400PW USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................5 4. CONTROL PANEL....................................................................................................... 6 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. If the appliance has ventilation openings in the base, they must not be covered e.g. by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets.
ENGLISH WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is complete.
www.aeg.com 5 6 7 8 9 Rating plate Salt container Air vent Rinse aid dispenser Detergent dispenser 10 Cutlery basket 11 Lower basket 12 Upper basket 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Rinsing phase. It comes on when the rinsing phase operates. Drying phase.
ENGLISH Indicator Description TimeSaver indicator. XtraDry indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. Delay indicator. ExtraHygiene indicator. 5.
www.aeg.com Programme Degree of soil Type of load Programme phases Options • Normal or light soil • Delicate crockery and glassware • Wash 45 °C • Rinses • Dry • XtraDry 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets .
ENGLISH How to set the programme selection mode the indicators , flash and the display is blank. The appliance is in programme selection mode when the programme indicator 6.2 The water softener 9 and The water softener removes minerals from the water supply, which would have a detrimental effect on the washing results and on the appliance. flashes and the display shows the programme duration. After activation, the appliance is in programme selection mode by default.
www.aeg.com How to set the water softener level Make sure the appliance is in user mode. 1. Press Program. • The indicators are off. • The display shows the current setting. – = rinse aid empty notification activated. – and still flashes. • The indicator • The display shows the current setting: e.g. = level 5. 2. Press Program repeatedly to change the setting. 3. Press the on/off button to confirm the setting. = rinse aid empty notification deactivated. 2. Press Start to change the setting. 3.
ENGLISH • The indicators and are off. • The indicator still flashes. • The display shows the current setting: 11 2. Press Delay to change the setting: = AirDry deactivated. 3. Press on/off to confirm the setting. = AirDry activated. 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other.
www.aeg.com The display shows the updated programme duration. 8. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets.
ENGLISH 8.2 How to fill the rinse aid dispenser A D B C M AX 4 1. Press the release button (D) to open the lid (C). 2. Pour the rinse aid in the dispenser (A) until the liquid reaches the fill level 'max'. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the release button locks into position. 1 3 2 + CAUTION! Only use rinse aid specifically designed for dishwashers.
www.aeg.com B A 30 3. Set the applicable options. 4. Press Start to start the programme. • The indicator of the running phase comes on. • The programme duration starts to decrease with steps of 1 minute. D 20 C CAUTION! Only use detergent specifically designed for dishwashers. 1. Press the release button (B) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (A). 3. If the programme has a prewash phase, put a small quantity of detergent in the compartment (D). 4.
ENGLISH Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again. Press simultaneously Delay and Option until the appliance is in programme selection mode. Cancelling the programme Press and hold simultaneously Delay and Option until the appliance is in programme selection mode. Make sure that there is detergent in the detergent dispenser before you start a new programme.
www.aeg.com 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5. Adjust the released quantity of rinse aid. 6. Activate the rinse aid empty notification. 10.
ENGLISH 17 C B A 1. Turn the filter (B) counterclockwise and remove it. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 4. Wash the filters.
www.aeg.com 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance.
ENGLISH 19 Problem and alarm code Possible cause and solution The appliance does not fill with water. • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the filter in the inlet hose is not clogged. • Make sure that the inlet hose has no kinks or bends. The display shows or . The appliance does not drain the water.
www.aeg.com Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes. Once you have checked the appliance, deactivate and activate the appliance. If the problem occurs again, contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre. 12.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results.
ENGLISH 21 Problem Possible cause and solution Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener". • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together. There are residues of detergent in the dispenser at the end of the programme. • The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
www.aeg.com Capacity Place settings 9 Power consumption Left-on mode (W) 5.0 Power consumption Off-mode (W) 0.50 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption. 14. ENVIRONMENTAL CONCERNS Recycle materials with the symbol . Put the packaging in relevant containers to recycle it.
ENGLISH 23
156916750-A-142017 www.aeg.