FFB62400PW USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................5 4. CONTROL PANEL....................................................................................................... 6 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. If the appliance has ventilation openings in the base, they must not be covered e.g. by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets.
ENGLISH WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is complete.
www.aeg.com 5 6 7 8 9 Rating plate Salt container Air vent Rinse aid dispenser Detergent dispenser 10 Cutlery basket 11 Lower basket 12 Upper basket 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Rinsing phase. It comes on when the rinsing phase operates. Drying phase.
ENGLISH Indicator Description TimeSaver indicator. XtraDry indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. Delay indicator. ExtraHygiene indicator. 5.
www.aeg.com Programme Degree of soil Type of load Programme phases Options • Normal or light soil • Delicate crockery and glassware • Wash 45 °C • Rinses • Dry • XtraDry 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets .
ENGLISH How to set the programme selection mode the indicators , flash and the display is blank. The appliance is in programme selection mode when the programme indicator 6.2 The water softener 9 and The water softener removes minerals from the water supply, which would have a detrimental effect on the washing results and on the appliance. flashes and the display shows the programme duration. After activation, the appliance is in programme selection mode by default.
www.aeg.com How to set the water softener level Make sure the appliance is in user mode. 1. Press Program. • The indicators are off. • The display shows the current setting. – = rinse aid empty notification activated. – and still flashes. • The indicator • The display shows the current setting: e.g. = level 5. 2. Press Program repeatedly to change the setting. 3. Press the on/off button to confirm the setting. = rinse aid empty notification deactivated. 2. Press Start to change the setting. 3.
ENGLISH • The indicators and are off. • The indicator still flashes. • The display shows the current setting: 11 2. Press Delay to change the setting: = AirDry deactivated. 3. Press on/off to confirm the setting. = AirDry activated. 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other.
www.aeg.com The display shows the updated programme duration. 8. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets.
ENGLISH 8.2 How to fill the rinse aid dispenser A B M AX 4 1 3 2 + - C D 13 1. Press the release button (D) to open the lid (C). 2. Fill the dispenser (A) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the release button locks into position. You can turn the selector of the released quantity (B) between position 1 (lowest quantity) and position 4 or 6 (highest quantity).
www.aeg.com Starting a programme 1. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode and the door is closed. 2. Press Program again and again until the indicator of the desired programme is on. The display shows the programme duration. 3. Set the applicable options. 4. Press Start to start the programme. • The indicator of the running phase is on. • The programme duration starts to decrease with steps of 1 minute.
ENGLISH 15 10. HINTS AND TIPS 10.1 General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase. • Always use the whole space of the baskets.
www.aeg.com • Make sure that the spray arm can move freely before you start a programme. 10.5 Before starting a programme Make sure that: • The filters are clean and correctly installed. • The cap of the salt container is tight. • The spray arms are not clogged. • There is dishwasher salt and rinse aid (unless you use multi- tablets). • The position of the items in the baskets is correct. • The programme is applicable for the type of load and for the degree of soil.
ENGLISH 17 CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.3 External cleaning 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7.
www.aeg.com solve the problem by yourself with the help of the information in the table or contact an Authorised Service Centre. WARNING! Repairs not properly done may result in serious risk to the safety of the user. Any repairs must be performed by qualified personnel. With some problems, the display shows an alarm code. The majority of problems that can occur can be solved without the need to contact an Authorised Service Centre.
ENGLISH Problem and alarm code 19 Possible cause and solution The remaining time in the • This is not a defect. The appliance is working correctly. display increases and skips nearly to the end of program time. Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if applicable). The appliance door is difficult to close. • The appliance is not levelled.
www.aeg.com Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option XtraDry and set AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets.
ENGLISH 21 Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. The level of salt is low, check the refill indicator. The cap of the salt container is loose. Your tap water is hard.
www.aeg.com your local recycling facility or contact your municipal office.
ENGLISH 23
156914690-A-052017 www.aeg.