FFB62620PW FFB62620PM USER MANUAL NL FR Gebruiksaanwijzing Afwasautomaat Notice d'utilisation Lave-vaisselle 2 25
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE......................................................................................... 2 2. VEILIGHEIDSVOORSCHRIFTEN.................................................................................4 3. BESCHRIJVING VAN HET PRODUCT........................................................................6 4. BEDIENINGSPANEEL................................................................................................. 7 5. PROGRAMMA’S..................
NEDERLANDS 3 niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • Leg het bestek in de besteklade met de scherpe randen naar beneden of leg ze horizontaal in de besteklade met de scherpe randen naar beneden. Laat om ongelukken te voorkomen het apparaat niet onbeheerd achter met open deur. Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht. Gebruik geen waterstralen onder druk en/of stoom om het apparaat te reinigen.
NEDERLANDS moet worden, moet een ASTA (BS 1362)-zekering van 13-ampère worden gebruikt. 2.3 Aansluiting aan de waterleiding • Beschadig de waterslangen niet. • Indien buizen lang niet zijn gebruikt, er reparaties hebben plaatsgevonden of er nieuwe apparaten zijn geplaatst (watermeters, enz.), moet u, voordat de nieuwe buizen worden aangesloten, het water laten stromen tot het schoon en helder is. • Zorg ervoor dat er geen zichtbare waterlekken zijn tijdens en na het eerste gebruik van het apparaat.
www.aeg.com 3.
NEDERLANDS 4. BEDIENINGSPANEEL 1 2 3 8 1 2 3 4 5 Aan/uit-toets Program-toets Programma-indicatielampjes Weergave Delay-toets 4 7 5 6 6 Option-toets 7 Indicatielampjes 8 Start-toets 4.1 Indicatielampjes Aanduiding Beschrijving Wasfase. Gaat aan wanneer de wasfase loopt. Spoelfase. Gaat aan wanneer de spoelfase loopt. Droogfase. Gaat aan wanneer de droogfase loopt. Einde-indicatielampje. TimeSaver-indicatielampje. XtraDry-indicatielampje. Glansmiddelindicatielampje.
www.aeg.com 5.
NEDERLANDS Programma 1) Water (l) Energie(kWh) Bereidingstijd (min.) 12.5 - 14.5 1.4 - 1.7 170 - 190 12 - 14 0.7 - 0.9 82 - 92 10 0.9 30 9 - 10 1.1 - 1.3 230 - 250 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.
www.aeg.com De waterontharder moet worden afgesteld op de hardheid van het water in uw woonplaats. Uw waterleidingbedrijf kan u informeren over de hardheid van het water in uw woonplaats. Het is belangrijk om het correcte niveau voor de waterontharder in te stellen voor goede wasresultaten. Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.
NEDERLANDS droogprestaties dient u echter altijd glansmiddel te gebruiken. Schakel de aanduiding in om de glansmiddelindicator actief te houden als u standaard wasmiddel of multitabletten zonder glansmiddel gebruikt. Het uitschakelen van de melding van een leeg glansmiddeldoseerbakje Zorg dat het apparaat in de gebruikersmodus staat. 1. Druk op Start. • De indicatielampjes en , zijn uit. • Het indicatielampje blijft knipperen. • Het display toont de huidige 1. Druk op Delay.
www.aeg.com Gebruik om de droogresultaten te verbeteren de optie XtraDry of activeer AirDry. Het deactiveren van AirDry Zorg dat het apparaat in de gebruikersmodus staat. 1. Druk op Option. • De indicatielampjes en , zijn uit. • Het indicatielampje blijft knipperen. • Het display toont de huidige instelling: = AirDry ingeschakeld. 2. Druk op Option om de instelling te wijzigen: = AirDry uitgeschakeld. 3. Druk op aan/uit om de instelling te bevestigen. 7.
NEDERLANDS 7.3 ExtraHygiene Deze optie geeft hygiënischere resultaten door de temperatuur tijdens de laatste spoelfase gedurende minstens 10 minuten op 70°C te houden. Het activeren van ExtraHygiene Druk op Option totdat het indicatielampje aangaat. 13 Als de optie niet van toepassing is op het programma, dan gaat het bijbehorende indicatielampje niet branden of het knippert even en gaat dan uit. Het display geeft de bijgewerkte programmaduur weer. - 8.
www.aeg.com LET OP! Water en zout kunnen uit het zoutreservoir stromen als u het bijvult. Start na het bijvullen van het zoutreservoir onmiddellijk een programma om corrosie te voorkomen. 8.2 Het vullen van het glansmiddeldoseerbakje A 1. Open het deksel (C). 2. Vul het glansmiddeldoseerbakje (B) niet verder dan de aanduiding ''MAX''. 3. Verwijder gemorst glansmiddel met een absorberend doekje om te voorkomen dat er te veel schuim ontstaat. 4. Sluit het deksel.
NEDERLANDS LET OP! Gebruik uitsluitend vaatwasmiddelen die specifiek zijn bedoeld voor gebruik in vaatwassers 1. Druk op de ontgrendelknop (A) om de deksel te openen (C). 2. Doe de vaatwastablet of het poeder in het doseerbakje (B). 3. Plaats een kleine hoeveelheid van het vaatwasmiddel in de binnenkant van de deur van het apparaat als het programma een voorwasfase heeft. 4. Sluit het deksel. Zorg ervoor dat de deksel op zijn plaats dichtklikt. 9.
www.aeg.com De uitgestelde start annuleren tijdens het aftellen Als u de uitgestelde start annuleert, moet u een programma en de opties opnieuw instellen. Houd tegelijkertijd Delay en Option ingedrukt tot het apparaat in de programmakeuzemodus staat. Een programma annuleren Houd tegelijkertijd Delay en Option ingedrukt tot het apparaat in de programmakeuzemodus staat. Controleer of er vaatwasmiddel in het vaatwasmiddelbakje aanwezig is voordat u een nieuw programma start.
NEDERLANDS 10.3 Wat moet u doen als u wilt stoppen met het gebruik van multitabletten Doe het volgende voordat u begint met het gebruiken van apart wasmiddel, zout en glansmiddel. 1. Stel het hoogste niveau van de waterontharder in. 2. Zorg ervoor dat het zout- en het glansmiddeldoseerbakje gevuld zijn. 3. Start het kortste programma met een spoelfase. Voeg geen afwasmiddel toe en ruim de mandjes niet in. 4. Als het programma is voltooid, wijzigt u de waterontharder in de waterhardheid van uw omgeving. 5.
www.aeg.com 11.1 De filters reinigen Het filtersystem bestaat uit 3 delen. C B A 1. Draai de filter (B) linksom en verwijder het. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter (A) terug. Zorg ervoor dat het goed onder de 2 geleidingen zit. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3.
NEDERLANDS 11.2 De bovenste sproeiarm schoonmaken We raden u aan om de bovenste sproeiarm regelmatig schoon te maken om te voorkomen dat vuil de gaten verstopt. 19 naar boven in de richting van de lagere pijl en draait u hem tegelijkertijd tegen de wijzers van de klok in, zodat hij op zijn plek vergrendelt. Verstopte gaten kunnen onbevredigende wasresultaten opleveren. 1. Trek het bovenrek naar buiten. 2.
www.aeg.com contact op te nemen met een erkend servicecentrum. WAARSCHUWING! Niet juist uitgevoerde reparaties kunnen de veiligheid van de gebruiker ernstig in gevaar brengen. Alle reparaties moeten worden uitgevoerd door bevoegd personeel. Bij sommige problemen wordt er op de display een alarmcode weergegeven. Het merendeel van de problemen die ontstaan kunnen worden opgelost zonder contact op te nemen met een erkend servicecentrum.
NEDERLANDS 21 Probleem en alarmcode Mogelijke oorzaak en oplossing Het programma duurt te lang. • Kies de optie TimeSaver om de programmaduur te verkorten. • Als de optie uitgestelde start is ingesteld, annuleert u deze functie of wacht u tot het aftellen is voltooid. De resterende duur in het display wordt verlengd en schakelt bijna naar het eind van de programmaduur. • Dit is geen storing. Het apparaat werkt goed. Kleine lekkage uit de deur van het apparaat. • Het apparaat staat niet waterpas.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Slechte droogresultaten. • Serviesgoed heeft te lang in het gesloten apparaat gestaan. • Het glansmiddel is op of de dosering van glansmiddel is niet voldoende. Stel de dosering van het glansmiddel in op een hogere stand. • Plastic voorwerpen moeten mogelijk met een doek worden afgedroogd. • Activeer voor de beste droogprestatie de optie XtraDry en stel AirDry in. • We raden aan altijd glansmiddel te gebruiken, zelfs in combinatie met wastabletten.
NEDERLANDS Probleem 23 Mogelijke oorzaak en oplossing Er bevinden zich aan het einde • De vaatwastablet raakte klem in het vaatwasmiddeldovan het programma resten van seerbakje en is daardoor niet volledig weggespoeld vaatwasmiddel in het vaatwasdoor het water. middeldoseerbakje. • Het water kan het vaatwasmiddel niet uit het vaatwasmiddeldoseerbakje spoelen. Zorg ervoor dat de bovenste sproeiarm niet geblokkeerd of verstopt is.
www.aeg.com Energieverbruik Modus aan laten (W) 5.0 Energieverbruik Uit-modus (W) 0.10 1) Zie het typeplaatje voor andere waarden. 2) Als het hete water door een alternatieve, milieuvriendelijkere energiebron geproduceerd wordt (bijv. zonnepanelen en windenergie), gebruik dan een heetwatervoorziening om het energieverbruik te verminderen. 14. MILIEUBESCHERMING Recycle de materialen met het symbool . Gooi de verpakking in een geschikte verzamelcontainer om het te recyclen.
FRANÇAIS 25 TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................25 2. CONSIGNES DE SÉCURITÉ......................................................................................27 3. DESCRIPTION DE L'APPAREIL.................................................................................29 4. BANDEAU DE COMMANDE....................................................................................30 5. PROGRAMMES.......................
www.aeg.com pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
FRANÇAIS • • • • • • 27 agréé ou un technicien qualifié afin d'éviter tout danger. Placez les couverts dans le panier à couverts, avec les extrémités pointues vers le bas, ou placez-les dans le bac à couverts en position horizontale, bords tranchants vers le bas. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter de vous prendre accidentellement les pieds dedans. Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur.
www.aeg.com prise de courant est accessible une fois l'appareil installé. • Ne tirez jamais sur le câble d'alimentation pour débrancher l'appareil. Tirez toujours sur la fiche. • Cet appareil est conforme aux directives CEE. • Royaume-Uni et Irlande uniquement. Cet appareil est fourni avec un câble d'alimentation de 13 A. Si vous devez changer le fusible de la fiche secteur, utilisez uniquement un fusible 13 A approuvé ASTA (BS 1362). 2.
FRANÇAIS 3.
www.aeg.com 4. BANDEAU DE COMMANDE 1 2 8 1 2 3 4 5 Touche Marche/Arrêt Touche Program Voyants de programme Affichage Touche Delay 3 4 7 5 6 6 Touche Option 7 Voyants 8 Touche Start 4.1 Voyants Indicateur Description Phase de lavage. Il s'allume au cours de la phase de lavage. Phase de rinçage. Il s'allume au cours de la phase de rinçage. Phase de séchage. Il s'allume au cours de la phase de séchage. Voyant de fin. Voyant TimeSaver. Voyant XtraDry. Voyant du réservoir de liquide de rinçage.
FRANÇAIS 31 5.
www.aeg.com Programme1) Eau (l) Énergie (kWh) Durée (min) 7 - 15 0.6 - 1.7 40 - 170 12.5 - 14.5 1.4 - 1.7 170 - 190 12 - 14 0.7 - 0.9 82 - 92 10 0.9 30 9 - 10 1.1 - 1.3 230 - 250 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
FRANÇAIS 33 L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région. Il est important de régler l'adoucisseur d'eau sur un niveau adéquat pour vous garantir de bons résultats de lavage. commencent à clignoter et que plus rien ne s'affiche. 6.
www.aeg.com 3. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.4 Le distributeur de liquide de rinçage 6.3 Notification de liquide de rinçage vide Le liquide de rinçage permet à la vaisselle de sécher sans traces ni taches. Le liquide de rinçage permet à la vaisselle de sécher sans traces ni taches. Le liquide de rinçage est automatiquement ajouté au cours du rinçage chaud.
FRANÇAIS 35 Pour améliorer les performances de séchage, reportez-vous à l'option XtraDry ou activez l'option AirDry. Comment désactiver l'option AirDry Assurez-vous que l'appareil est en mode Utilisateur. 1. Appuyez sur Option. • Les voyants , et sont éteints. Durant la phase de séchage, un dispositif ouvre la porte de l'appareil. Elle est alors maintenue entrouverte. ATTENTION! Ne tentez pas de refermer la porte de l'appareil dans les 2 minutes suivant son ouverture automatique.
www.aeg.com d'eau et la température du dernier rinçage peuvent être affectés. L'option XtraDry est une option permanente pour tous les programmes, à l'exception du programme pour lequel elle doit être sélectionnée à chaque cycle. À chaque fois que vous sélectionnez le programme , l'option XtraDry est désactivée et doit être sélectionnée manuellement. Pour les autres programmes, l'option XtraDry est permanente et automatiquement utilisée pour les cycles suivants.
FRANÇAIS 37 lavage ne démarre qu'une fois cette procédure achevée. La procédure sera répétée régulièrement. 8.1 Réservoir de sel régénérant ATTENTION! Utilisez uniquement du gros sel spécialement conçu pour les lave-vaisselle. Le sel fin augmente le risque de corrosion. Le sel permet de recharger la résine dans l'adoucisseur d'eau et de garantir de bons résultats de lavage au quotidien. Comment remplir le réservoir de sel 1.
www.aeg.com 3. Si le liquide de rinçage déborde, épongez-le avec un chiffon absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. Si vous utilisez des pastilles de détergent multifonctions et que les performances du séchage sont satisfaisantes, l'indication de remplissage du liquide de rinçage peut être désactivée.
FRANÇAIS Départ d'un programme 1. Appuyez sur la touche Marche/Arrêt pour mettre en marche l'appareil. Assurez-vous que l'appareil est en mode de sélection de programme et que la porte est fermée. 2. Appuyez sur Program à nouveau et encore jusqu'à ce que l'indicateur du programme souhaité soit allumé. L'affichage indique la durée du programme. 3. Sélectionnez les options compatibles. 4. Appuyez sur la touche Start pour lancer le programme. • L'indicateur de la phase de fonctionnement est activé.
www.aeg.com Si vous ouvrez la porte avant l'activation de Auto Off, l'appareil est automatiquement éteint. 2. Fermez le robinet d'arrivée d'eau. 10. CONSEILS 10.1 Raccordement Les conseils suivants vous garantissent des résultats de lavage et de séchage optimaux au quotidien, et vous aideront à protéger l'environnement. • Videz les plus gros résidus alimentaires des plats dans une poubelle. • Ne rincez pas vos plats à la main au préalable.
FRANÇAIS 5. Ajustez la quantité de liquide de rinçage libérée. 6. Activez la notification du distributeur de liquide de rinçage vide. 10.4 Chargement des paniers • Utilisez uniquement cet appareil pour laver des articles qui peuvent passer au lave-vaisselle. • Ne mettez pas dans le lave-vaisselle des articles en bois, en corne, en aluminium, en étain et en cuivre. • Ne placez pas dans l'appareil des objets pouvant absorber l'eau (éponges, chiffons de nettoyage).
www.aeg.com C B A 1. Faites pivoter le filtre (B) dans le sens antihoraire puis sortez-le. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat à sa place (A). Vérifiez qu'il est correctement positionné sous les deux guides. 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A).
FRANÇAIS ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 43 4. Pour réinstaller le bras d'aspersion supérieur sur le panier, poussez le bras d'aspersion vers le haut, dans la direction indiquée par la flèche du bas, tout en le tournant vers la gauche jusqu'à ce qu'il se bloque en place.
www.aeg.com 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'il s'arrête en cours de fonctionnement, vérifiez d'abord si vous pouvez résoudre le problème par vous-même en vous aidant des informations du tableau ou contactez le Service après-vente agréé. Pour certaines anomalies, l'écran affiche un code d'alarme. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé.
FRANÇAIS 45 Problème et code d'alarme Cause et solution possibles Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Fermez le robinet d'eau et contactez le service aprèsvente agréé. . L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps. • Sélectionnez l'option TimeSaver pour raccourcir la durée du programme.
www.aeg.com 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
FRANÇAIS 47 Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage pour lavevaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après-vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble.
www.aeg.com 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 850 / 610 Branchement électrique1) Tension (V) 220 - 240 Fréquence (Hz) 50 bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 13 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.
FRANÇAIS 49
www.aeg.
FRANÇAIS 51
117879540-A-312017 www.aeg.