FFB62620PW FFB62620PM USER MANUAL EN DE User Manual Dishwasher Benutzerinformation Geschirrspüler 2 24
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
ENGLISH • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. • UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses.
www.aeg.com 3.
ENGLISH 7 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Salt indicator. It is on when the salt container needs refilling. It is always off while the programme operates. Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. It is always off while the programme operates. Washing phase indicator.
www.aeg.com 5. PROGRAMMES The order of the programmes in the table may not reflect their sequence on the control panel.
ENGLISH 9 5.1 Consumption values Programme 1) Water (l) Energy (kWh) Duration (min) 10.5 0.921 235 8 - 15 0.7 - 1.7 46 - 170 12.5 - 14.5 1.4 - 1.7 170 - 190 12 - 14 0.8 - 1.0 82 - 92 10 0.9 30 12 - 13 1.1 - 1.3 230 - 250 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes To receive the necessary information for conducting performance tests (e.g.
www.aeg.com the indicators , , The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area. It is important to set the right level of the water softener to assure good washing results. and flash and the display is blank. 6.2 The water softener The water softener removes minerals from the water supply, which would have a negative effect on the washing results and on the appliance.
ENGLISH automatically released during the hot rinse phase. When the rinse aid chamber is empty, the rinse aid indicator is turned on notifying to refill rinse aid. If the drying results are satisfactory while using multitablets only, it is possible to deactivate the notification for refilling rinse aid. However, for best drying performance, always use rinse aid. If standard detergent or multi-tablets without rinse aid are used, activate the notification to keep the rinse aid refill indicator active.
www.aeg.com How to deactivate AirDry Make sure the appliance is in user mode. 1. Press Option. • The indicators and – = AirDry is activated. 2. Press Option to change the setting. 3. Press on/off to confirm the setting. , are off. • The indicator flashes. • The display shows the current setting. – = AirDry is deactivated. still 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running.
ENGLISH °C for at least 10 minutes during the last rinsing phase. 13 The display shows the updated programme duration. How to activate ExtraHygiene Press Option until the indicator is on. 8. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5.
www.aeg.com 8.2 How to fill the rinse aid dispenser A B CAUTION! Only use rinse aid designed specifically for dishwashers. 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent excessive foam formation. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) is clear. C 9. DAILY USE 1. Open the water tap. 2.
ENGLISH 15 4. Press Start to start the programme. • The indicator of the running phase is on. • The programme duration starts to decrease with steps of 1 minute. Press and hold simultaneously Delay and Option until the appliance is in programme selection mode. Starting a programme with delay start Press and hold simultaneously Delay and Option until the appliance is in programme selection mode. Make sure that there is detergent in the detergent dispenser before you start a new programme. 1.
www.aeg.com • Always use the whole space of the baskets. • Make sure that items in the baskets do not touch or cover each other. Only then can the water completely reach and wash the dishes. • You can use dishwasher detergent, rinse aid and salt separately or you can use the multi-tablets (e.g. ''All in 1''). Follow the instructions on the packaging. • Select a programme according to the type of load and the degree of soil. offers the most efficient use of water and energy consumption. 10.
ENGLISH 10.6 Unloading the baskets 1. Let the tableware cool down before you remove it from the appliance. Hot items can be easily damaged. 2. First remove items from the lower basket, then from the upper basket. 17 After the programme is completed, water can still remain on the inside surfaces of the appliance. 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results.
www.aeg.com 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 3. Wash the spray arm under running water. Use a thin pointed tool, e.g. a toothpick, to remove particles of soil from the holes. 4. To install the spray arm back, press the spray arm upwards and simultaneously turn it counterclockwise until it locks into place.
ENGLISH 11.4 Internal cleaning • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth. • To maintain the performance of your appliance, use a cleaning product designed specifically for dishwashers at least once a month. Carefully follow the instructions on the packaging of the product. 19 • Do not use abrasive products, abrasive cleaning pads, sharp tools, strong chemicals, scourer or solvents.
www.aeg.com Problem and alarm code Possible cause and solution The anti-flood device is on. • Close the water tap and contact an Authorised Service Centre. The display shows . The appliance stops and • It is normal. It provides optimal cleaning results and enstarts more times during opergy savings. eration. The programme lasts too long. • If the delay start option is set, cancel the delay setting or wait for the end of the countdown.
ENGLISH 21 12.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results. • Refer to "Daily use", "Hints and tips" and the basket loading leaflet. • Use more intensive washing programmes. • Clean spray arm jets and the filter. Refer to "Care and Cleaning". Poor drying results. • Tableware has been left for too long inside the closed appliance. • There is no rinse aid or the dosage of rinse aid is not sufficient.
www.aeg.com Problem Possible cause and solution There are residues of detergent in the dispenser at the end of the programme. • The detergent tablet got stuck in the dispenser and was not completely washed away by water. • Water cannot wash away the detergent from the dispenser. Make sure that the spray arm is not blocked or clogged. • Make sure that items in the baskets do not impede the lid of the detergent dispenser from opening. Odours inside the appliance. • Refer to "Internal cleaning".
ENGLISH Energy consumption of standard cleaning cycle (kWh) 0.921 Power consumption in off mode (W) 0.50 Power consumption in left-on mode (W) 5.0 23 Water consumption in litres per year, based on 280 standard clean2940 ing cycles. The actual water consumption will depend on how the appliance is used Drying efficiency class on a scale from G (least efficient) to A (most efficient) A The ‘standard programme’ is the standard cleaning cycle to which the information in the label and the fiche relates.
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE........................................................................................... 25 2. SICHERHEITSANWEISUNGEN.................................................................................27 3. GERÄTEBESCHREIBUNG......................................................................................... 28 4. BEDIENFELD..............................................................................................................29 5.
DEUTSCH 1. 25 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com Bauernhöfe, Personalküchenbereiche in Geschäften, Büros und anderen Arbeitsumfeldern. – Für Gäste in Hotels, Motels, Pensionen und anderen wohnungsähnlichen Räumlichkeiten. Nehmen Sie keine technischen Änderungen am Gerät vor. Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt.
DEUTSCH 27 2. SICHERHEITSANWEISUNGEN 2.1 Montage WARNUNG! Die Montage des Geräts darf nur von einer qualifizierten Fachkraft durchgeführt werden. • Entfernen Sie das gesamte Verpackungsmaterial. • Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. • Halten Sie sich an die mitgelieferte Montageanleitung. • Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk.
www.aeg.com solche nicht in die Nähe oder auf das Gerät. des Wasserzulaufschlauchs an den autorisierten Kundendienst. 2.4 Gebrauch 2.5 Service • Setzen oder stellen Sie sich niemals auf die geöffnete Gerätetür. • Geschirrspüler-Reinigungsmittel sind gefährlich. Beachten Sie die Sicherheitsanweisungen auf der Reinigungsmittelverpackung. • Trinken Sie nicht das Wasser aus dem Gerät und verwenden Sie es nicht zum Spielen. • Nehmen Sie kein Geschirr aus dem Gerät, bevor das Programm beendet ist.
DEUTSCH 9 Klarspülmittel-Dosierer 10 Reinigungsmittelfach 11 Besteckkorb 29 12 Unterkorb 13 Oberkorb 4. BEDIENFELD 1 2 8 1 2 3 4 5 Taste „Ein/Aus“ Program Taste Programmkontrolllampen Display Delay Taste 3 4 7 5 6 6 Option Taste 7 Kontrolllampen 8 Start Taste 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe Salz. Leuchtet, wenn der Salzbehälter nachgefüllt werden muss. Sie erlischt während des Programmbetriebs. Kontrolllampe Klarspülmittel.
www.aeg.com Kontrolllampe Beschreibung Kontrolllampe Programmende. Leuchtet nach dem Ende des Spülprogramms. Kontrolllampe Delay. Kontrolllampe TimeSaver. Kontrolllampe XtraDry. Kontrolllampe ExtraHygiene. 5. PROGRAMME Die Reihenfolge der Programme in der Tabelle entspricht möglicherweise nicht ihrer Reihenfolge auf dem Bedienfeld.
DEUTSCH Programm Verschmutzungsgrad Beladung Programmphasen Optionen 5) • Vor kurzem be• Hauptspülgang 60 °C nutztes Geschirr • Spülen • Geschirr und Besteck • ExtraHygiene • XtraDry 6) • Normaler Verschmutzungsgrad • Geschirr und Besteck • XtraDry • • • • Vorspülen Hauptspülgang 50 °C Spülen Trocknen 31 1) Dieses Programm gewährleistet den wirtschaftlichsten Wasser- und Energieverbrauch für normal verschmutztes Geschirr und Besteck. Dies ist das Standardprogramm für Prüfinstitute.
www.aeg.com 5.2 Informationen für Prüfinstitute Geben Sie in Ihrer Anfrage den Produktnummerncode (PNC) an, den Sie auf dem Typenschild finden. Wenn Sie Informationen zur Durchführung von Leistungsprüfungen (z.B. gemäß EN60436) benötigen, schicken Sie eine E-Mail an: Bezüglich anderer Fragen zu Ihrem Geschirrspüler siehe die mit dem Gerät gelieferte Bedienungsanleitung. info.test@dishwasher-production.com 6. EINSTELLUNGEN 6.
DEUTSCH Deutsche Wasserhärtegrade (°dH) Französische Wasserhärtegrade (°fH) mmol/l 43 - 46 76 - 83 7,6 - 8,3 53 - 57 9 37 - 42 65 - 75 6,5 - 7,5 46 - 52 8 29 - 36 51 - 64 5,1 - 6,4 36 - 45 7 23 - 28 40 - 50 4,0 - 5,0 28 - 35 6 19 - 22 33 - 39 3,3 - 3,9 23 - 27 5 1) 15 - 18 26 - 32 2,6 - 3,2 18 - 22 4 11 - 14 19 - 25 1,9 - 2,5 13 - 17 3 4 - 10 7 - 18 0,7 - 1,8 5 - 12 2 <4 <7 <0,7 <5 1 2) 33 Clarke Was- Einstellung für den serhärtegra- Wasserenthärter de 1) W
www.aeg.com Ausschalten der Klarspülmittelnachfüllanzeige Stellen Sie sicher, dass sich das Gerät im Benutzermodus befindet. 1. Drücken Sie Start. • Die Kontrolllampen und , erlöschen. • Die Kontrolllampe blinkt weiterhin. • Im Display wird die aktuelle Einstellung angezeigt. – Klarspülmittel zugegeben wird. 2. Drücken Sie Delay wiederholt zum Ändern der Einstellung. 3. Drücken Sie Ein/Aus zum Bestätigen der Einstellung. 6.
DEUTSCH VORSICHT! Haben Kinder Zugang zum Gerät, wird empfohlen AirDry auszuschalten, da das Öffnen der Tür eine Gefahr darstellen könnte. So schalten Sie AirDry aus Stellen Sie sicher, dass sich das Gerät im Benutzermodus befindet. 1. Drücken Sie Option. • Die Kontrolllampen und 35 • Die Kontrolllampe blinkt weiterhin. • Im Display wird die aktuelle Einstellung angezeigt. – = AirDry ist ausgeschaltet. – = AirDry ist eingeschaltet. 2. Drücken Sie Option zum Ändern der Einstellung. 3.
www.aeg.com 7.2 TimeSaver Mit dem TimeSaver können Sie die Dauer des gewählten Programms um etwa 50% verkürzen. Die Spülergebnisse entsprechen denen einer normalen Programmdauer. Die Trockenergebnisse können beeinträchtigt werden. Das Display zeigt die aktualisierte Programmdauer an. 7.3 ExtraHygiene Diese Option bietet bessere Hygieneergebnisse, indem die Temperatur im letzten Spülgang für mindestens 10 Minuten auf 70 °C gehalten wird.
DEUTSCH 37 8.2 Füllen des KlarspülmittelDosierers A B 4. Schütteln Sie den Trichter leicht am Griff, damit auch die verbleibenden Körner in den Behälter gelangen. 5. Entfernen Sie das Salz, das sich um die Öffnung des Salzbehälters herum angesammelt hat. C VORSICHT! Verwenden Sie ausschließlich Klarspülmittel für Geschirrspüler. 6. Drehen Sie den Deckel des Salzbehälters im Uhrzeigersinn, um den Salzbehälter zu schließen. VORSICHT! Beim Befüllen des Salzbehälters können Wasser und Salz austreten.
www.aeg.com 9.1 Verwenden des Reinigungsmittels A B • Die Kontrolllampe für das laufende Programm leuchtet. • Die Programmdauer nimmt in Schritten von jeweils 1 Minute ab. Starten eines Programms mit Zeitvorwahl 1. Wählen Sie ein Programm. 2. Drücken Sie Delay wiederholt, bis im Display die gewünschte Zeitvorwahl angezeigt wird (zwischen 1 und 24 Stunden). 3. Drücken Sie Start, um den Countdown zu starten. C VORSICHT! Verwenden Sie nur Reinigungsmittel für Geschirrspüler. 1.
DEUTSCH Halten Sie Delay und Option gleichzeitig gedrückt, bis sich das Gerät im Programmwahlmodus befindet. Abbrechen eines Programms Halten Sie Delay und Option gleichzeitig gedrückt, bis sich das Gerät im Programmwahlmodus befindet. Bevor Sie ein neues Programm starten, stellen Sie sicher, dass der Reinigungsmittelbehälter gefüllt ist. Programmende Wenn das Programm beendet ist, wird im Display 0:00 angezeigt. Die Kontrolllampe leuchtet. Alle Tasten außer der Taste Ein/Aus sind inaktiv. 39 1.
www.aeg.com 10.3 Was tun, wenn Sie keine Multi-Reinigungstabletten mehr verwenden möchten Vorgehensweise, um zurück zur separaten Verwendung von Reinigungsmittel, Salz und Klarspülmittel zu kehren: 1. Stellen Sie die höchste Wasserenthärterstufe ein. 2. Stellen Sie sicher, dass der Salzbehälter und der KlarspülmittelDosierer gefüllt sind. 3. Starten Sie das kürzeste Programm mit einer Spülphase. Verwenden Sie kein Reinigungsmittel und beladen Sie die Körbe nicht. 4.
DEUTSCH 41 11. REINIGUNG UND PFLEGE WARNUNG! Schalten Sie das Gerät immer aus und ziehen Sie den Netzstecker aus der Steckdose, bevor Reinigungsarbeiten durchgeführt werden. Verschmutzte Siebe und verstopfte Sprüharme beeinträchtigen das Spülergebnis. Prüfen Sie die Siebe regelmäßig und reinigen Sie diese, falls nötig. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 11.1 Reinigen der Filter Das Filtersystem besteht aus 3 Teilen. 4. Reinigen Sie die Filter.
www.aeg.com 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet. VORSICHT! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 3. Reinigen Sie den Sprüharm unter fließendem Wasser. Entfernen Sie Verunreinigungen aus den Öffnungen des Sprüharms mit einem spitzen Gegenstand, z.B. einem Zahnstocher. 4.
DEUTSCH • Benutzen Sie keine Scheuermittel, scheuernde Reinigungsschwämmchen oder Lösungsmittel. 11.4 Reinigung des Geräteinnenraums • Reinigen Sie das Gerät und die Gummidichtung der Tür sorgfältig mit einem weichen, feuchten Tuch. • Verwenden Sie einmal im Monat ein spezielles Reinigungsmittel für Geschirrspüler, um die Leistungsfähigkeit des Geräts zu erhalten. Befolgen Sie sorgfältig die 43 Anweisungen auf der Reinigungsmittelverpackung.
www.aeg.com Störung und Alarmcode Mögliche Ursache und Abhilfe Es läuft kein Wasser in das Gerät. • Stellen Sie sicher, dass der Wasserzulaufhahn geöffnet ist. • Vergewissern Sie sich, dass der Wasserdruck der Wasserversorgung nicht zu niedrig ist. Diese Informationen erhalten Sie von Ihrem lokalen Wasserversorger. • Stellen Sie sicher, dass der Wasserzulaufhahn nicht verstopft ist. • Vergewissern Sie sich, dass das Sieb im Zulaufschlauch nicht verstopft ist.
DEUTSCH 45 Störung und Alarmcode Mögliche Ursache und Abhilfe Klappernde oder schlagende Geräusche aus dem Geräteinneren. • Das Geschirr ist nicht richtig in den Körben eingeordnet. Siehe Broschüre zum Beladen der Körbe. • Achten Sie darauf, dass sich die Sprüharme frei drehen können. Das Gerät löst die Sicherung • Die abgesicherte Stromstärke reicht nicht für den gleichaus. zeitigen Betrieb aller eingeschalteten Geräte. Überprüfen Sie, für welche Stromstärke die Steckdose bzw.
www.aeg.com Störung Mögliche Ursache und Abhilfe Wasserflecken und andere Flecken auf Gläsern und Geschirr. • Die zugegebene Klarspülmittelmenge ist zu niedrig. Stellen Sie eine höhere Klarspülmittelmenge ein. • Die Ursache kann in der Qualität des Klarspülmittels liegen. Das Geschirr ist nass. • Schalten Sie XtraDry und AirDry ein, um die beste Trocknungsleistung zu erzielen. • Das Programm enthält keine Trocknungsphase oder eine Trocknungsphase mit niedriger Temperatur.
DEUTSCH 47 Störung Mögliche Ursache und Abhilfe Kalkablagerungen auf dem Geschirr, im Innenraum und auf der Türinnenseite. • Die Salzmenge ist nicht ausreichend. Überprüfen Sie die Salzkontrolllampe. • Der Deckel des Salzbehälters ist locker. • Ihr Leitungswasser ist hart. Siehe „Wasserenthärter“. • Verwenden Sie Salz und schalten Sie die Regenerierung des Wasserenthärters ein, selbst wenn Sie MultiReinigungstabletten verwenden. Siehe „Wasserenthärter“.
www.aeg.com Wasserverbrauch in Liter/Jahr, auf der Grundlage von 280 Standardreinigungszyklen. Der tatsächliche Wasserverbrauch hängt von der Art der Nutzung des Geräts ab. 2940 Trocknungseffizienzklasse auf einer Skala von G (geringste Effizienz) bis A (höchste Effizienz).
DEUTSCH 49
www.aeg.
DEUTSCH 51
117879552-A-432018 www.aeg.