FFB83730PW USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
ENGLISH fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses. • Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.), let the water flow until it is clean and clear. • Ensure that there are no visible water leaks during and after the first use of the appliance. • The water inlet hose has a safety valve and a sheath with an inner mains cable.
www.aeg.com 3.
ENGLISH 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Rinsing phase. It comes on when the rinsing phase operates. Drying phase. It comes on when the drying phase operates. End indicator. TimeSaver indicator. XtraDry indicator. Rinse aid indicator.
www.aeg.com Indicator Description Delay indicator. ExtraHygiene indicator. 5.
ENGLISH Programme 8) Degree of soil Type of load Programme phases Options • Normal soil • Crockery and cutlery • • • • • XtraDry Prewash Wash 50 °C Rinses Dry 9 1) This programme offers the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets .
www.aeg.com 5.2 Information for test institutes info.test@dishwasher-production.com For all the necessary information for test performance, send an email to: Write down the product number (PNC) that is on the rating plate. 6. SETTINGS 6.1 Programme selection mode and user mode Press and hold simultaneously Delay and Option until the appliance is in programme selection mode. When the appliance is in programme selection mode it is possible to set a programme and to enter user mode.
ENGLISH 11 German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level. Whether you use a standard detergent or multi-tabs (with or without salt), set the proper water hardness level to keep the salt refill notification active.
www.aeg.com • The indicators and , are off. • The indicator still flashes. • The display shows the current setting: e.g. = level 4. – The levels of rinse aid range from 0A to 6A where level 0A means no rinse aid is used. 2. Press Delay repeatedly to change the setting. 3. Press on/off to confirm the setting. 6.5 AirDry AirDry improves the drying results with less energy consumption. AirDry is automatically activated with all programmes excluding applicable).
ENGLISH Not all options are compatible with each other. If you select non compatible options, the appliance automatically deactivates one or more of them. Only the indicators of the still active options are on. If an option is not applicable to a programme, the related indicator is off or it flashes quickly for a few seconds and then goes out. Activating options can affect the water and energy consumption as well as the programme duration. 7.1 XtraDry 13 The display shows the updated programme duration.
www.aeg.com 8.1 The salt container CAUTION! Use rough salt designed for dishwashers only. Fine salt increases the risk of corrosion. 8.2 How to fill the rinse aid dispenser A B The salt is used to recharge the resin in the water softener and to assure good washing results in daily use. How to fill the salt container 1. Turn the cap of the salt container counterclockwise and remove it. 2. Put 1 litre of water in the salt container (only for the first time). 3.
ENGLISH 15 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil. 9.1 Using the detergent A B 9.2 Setting and starting a programme Starting a programme 1.
www.aeg.com If the door is opened for more than 30 seconds during the drying phase, the running programme ends. It does not happen if the door is opened by AirDry function. Cancelling the delay start while the countdown operates When you cancel the delay start you have to set a programme and options again. 1. Open the appliance door. 2. Press and hold simultaneously Delay and Option until the appliance is in programme selection mode. Cancelling a programme 1. Open the appliance door. 2.
ENGLISH 10.2 Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance. • In areas with hard and very hard water we recommend to use plain dishwasher detergent (powder, gel, tablets containing no additional agents), rinse aid and salt separately for optimal cleaning and drying results. • At least once a month run the appliance with the use of appliance cleaner which is particularly suitable for this purpose.
www.aeg.com 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. 3. Remove the flat filter (A). 4. Wash the filters. 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6.
ENGLISH CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the upper spray arm 19 4. To engage again the spray arm to the basket, press the spray arm upwards in the direction indicated by the lower arrow and simultaneously turn it counterclockwise until it locks into place. We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. Clogged holes can cause unsatisfactory washing results. 1.
www.aeg.com • Using short-duration programmes regularly can cause grease and limescale buildup inside the appliance. Run long-duration programmes at least twice a month to prevent the buildup. 12. TROUBLESHOOTING WARNING! Improper repair of the appliance may pose a danger to the safety of the user. Any repairs must be performed by qualified personnel. to contact an Authorised Service Centre. Refer to the above table for information on possible problems.
ENGLISH 21 Problem and alarm code Possible cause and solution The programme lasts too long. • If the delay start option is set, cancel the delay setting or wait for the end of the countdown. • Activate the TimeSaver option to reduce the programme duration. • Activating options can increase the programme duration. The remaining time in the display increases and skips nearly to the end of the programme duration. • This is not a defect. The appliance is working correctly.
www.aeg.com Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option XtraDry and set AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets.
ENGLISH 23 Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. • For washing delicate items and glassware, select the dedicated programme. Refer to "Programmes".
www.aeg.com 14. ENVIRONMENTAL CONCERNS Recycle materials with the symbol . Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose of * appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
ENGLISH 25
www.aeg.
ENGLISH 27
117873370-A-492017 www.aeg.
