FFB83806PM USER MANUAL FR Notice d'utilisation Lave-vaisselle
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ.................................................................................2 2. CONSIGNES DE SÉCURITÉ........................................................................................4 3. DESCRIPTION DE L'APPAREIL...................................................................................6 4. BANDEAU DE COMMANDE......................................................................................7 5. PROGRAMMES.................
FRANÇAIS 3 pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.1 Sécurité des enfants et des personnes vulnérables.
www.aeg.com • • • • • • • • • La pression de l'eau en fonctionnement (minimale et maximale) doit se situer entre 0.5 (0.05) / 8 (0.8) bar (MPa) Respectez le nombre maximal de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger.
FRANÇAIS • Vérifiez que les paramètres figurant sur la plaque signalétique correspondent aux données électriques de votre réseau. • Utilisez toujours une prise de courant de sécurité correctement installée. • N'utilisez pas d'adaptateurs multiprises ni de rallonges. • Veillez à ne pas endommager la fiche secteur ni le câble d'alimentation. Le remplacement du câble d'alimentation de l'appareil doit être effectué par notre service après-vente agréé.
www.aeg.com appareils domestiques. Ne les utilisez pas pour éclairer votre logement. • Pour remplacer l'éclairage intérieur, contactez le service après-vente agréé. 2.6 Maintenance • Pour réparer l'appareil, contactez un service après-vente agréé. • Utilisez exclusivement des pièces d'origine. • Débranchez l'appareil de l'alimentation électrique. • Coupez le câble d'alimentation et mettez-le au rebut.
FRANÇAIS 3.1 Beam-on-Floor 7 Le faisceau Beam-on-Floor s'éteint lorsque vous arrêtez l'appareil. Le faisceau Beam-on-Floor est une lumière projetée sur le sol, sous la porte de l'appareil. La projection au sol peut être partiellement visible lorsque le mode AirDry est activé durant la phase de séchage. Pour savoir si le cycle est terminé, regardez le bandeau de commande. • Lorsque le programme démarre, le faisceau rouge s'allume et reste allumé pendant toute la durée du programme.
www.aeg.
FRANÇAIS Programme Degré de salissure Type de vaisselle Phases du programme P0 • Pas de vaisselle • Auto-nettoyage 9 Options 10) 1) Ce programme vous permet d'optimiser votre consommation d'eau et d'énergie pour la vaisselle et les couverts normalement sales. Il s'agit du programme standard pour les instituts de tests. 2) L'appareil détecte le degré de salissure et la quantité de vaisselle dans les paniers.
www.aeg.com Eau (l) Consommation électrique (kWh) Durée (min) P5 10 0.9 30 P7 12 - 14 0.8 - 1.0 82 - 92 P8 12 - 13 1.1 - 1.3 230 - 250 P9 4 0.1 14 P0 10 0.86 60 - 70 Programme 1) 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
FRANÇAIS 11 sélection de programme. Dans le cas contraire, définissez le mode de sélection de programme de la manière suivante : commencent à clignoter et que plus rien ne s'affiche. Maintenez les touches et enfoncées simultanément jusqu'à ce que l'appareil se mette en mode Programmation. L'adoucisseur d'eau élimine les minéraux de l'arrivée d'eau qui pourraient avoir un impact négatif sur les résultats de lavage et sur l'appareil.
www.aeg.com Comment régler le niveau de l'adoucisseur d'eau Assurez-vous que l'appareil est en mode Utilisateur. 1. Appuyez sur . , • Les voyants éteints. , et sont • Le voyant clignote toujours. • L'affichage indique le réglage actuel : Par ex., = niveau 5. 2. Appuyez plusieurs fois sur la touche pour modifier le réglage. 3. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.
FRANÇAIS s'est produite. Il est impossible de désactiver ces signaux sonores. Un signal sonore retentit également lorsque le programme est terminé. Par défaut, ce signal sonore est désactivé, mais il est possible de l'activer. Comment activer le signal sonore de fin de programme Assurez-vous que l'appareil est en mode Utilisateur. 1. Appuyez sur • Les voyants éteints. . , , et sont clignote toujours. • Le voyant • L'affichage indique le réglage actuel. – = le signal sonore est désactivé.
www.aeg.com Vous ne pouvez enregistrer qu'un programme. Tout nouveau réglage annule le précédent. Comment sélectionner le programme MyFavourite Comment enregistrer le programme MyFavourite Appuyez sur . • Le voyant MyFavourite est allumé. • L'affichage indique le numéro et la durée du programme. • Si des options ont été sauvegardées avec le programme, les voyants correspondant à ces options s'allument. 1. Sélectionnez le programme choisi.
FRANÇAIS programme. Les résultats de séchage peuvent être moins satisfaisants. L'affichage indique la durée du programme réactualisée. Cette option augmente la pression et la température de l'eau. Les phases de lavage et de séchage sont réduites. 7.3 ExtraHygiene Par défaut, l'option TimeSaver est désactivée, mais il est possible de l'activer manuellement. Cette option ne peut pas être utilisée en combinaison avec XtraDry. Comment activer l'option TimeSaver Appuyez sur .
www.aeg.com 8.2 Comment remplir le distributeur de liquide de rinçage A B 4. Secouez doucement l'entonnoir par la poignée pour faire tomber les derniers grains qu'il contient. 5. Enlevez le sel qui se trouve autour de l'ouverture du réservoir de sel régénérant. C 6. Tournez le couvercle du réservoir de sel régénérant vers la droite pour le refermer. ATTENTION! De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez.
FRANÇAIS 9.1 Comfort Lift 17 détache des deux côtés. ATTENTION! Ne vous asseyez pas et n'exercez pas de forte pression sur le panier verrouillé. ATTENTION! Ne dépassez pas la charge maximale de 18 kg. ATTENTION! Assurez-vous que les articles ne sont pas collés au cadre du panier car vous pourriez endommager ces articles, ainsi que le mécanisme Comfort Lift.
www.aeg.com 3. Si le programme comporte une phase de prélavage, versez une petite quantité de produit de lavage à l'intérieur de la porte de l'appareil. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. 9.3 Réglage et départ d'un programme Départ d'un programme 1. Laissez la porte de l'appareil entrouverte. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. 3.
FRANÇAIS Si vous ouvrez la porte avant l'activation de la fonction Auto Off, l'appareil s'éteint automatiquement. 2. Fermez le robinet d'arrivée d'eau. Fonction Auto Off Cette fonction réduit la consommation d'énergie en éteignant 19 automatiquement l'appareil lorsqu'il ne fonctionne pas. La fonction s'active : • 5 minutes après la fin du programme de lavage. • Au bout de 5 minutes si le programme n'a pas démarré. 10. CONSEILS 10.
www.aeg.com 5. Ajustez la quantité de liquide de rinçage libérée. 6. Activez la notification du distributeur de liquide de rinçage vide. 10.4 Chargement des paniers • N'utilisez l'appareil que pour laver des articles adaptés au lave-vaisselle. • Ne lavez pas au lave-vaisselle des articles en bois, en corne, en aluminium, en étain et en cuivre. • Ne placez pas dans l'appareil des objets pouvant absorber l'eau (éponges, chiffons de nettoyage). • Retirez les plus gros résidus alimentaires des plats.
FRANÇAIS 21 C B A 1. Faites pivoter le filtre (B) dans le sens antihoraire puis sortez-le. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat à sa place (A). Vérifiez qu'il est correctement positionné sous les deux guides. 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A).
www.aeg.com ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 4. Pour réinstaller le bras d'aspersion, pousser le bras vers le haut tout en le tournant vers la gauche, jusqu'à ce qu'il se verrouille en place. 11.2 Nettoyage du bras d'aspersion supérieur Nous vous conseillons de nettoyer régulièrement le bras d'aspersion supérieur afin d'éviter que ses orifices ne se bouchent.
FRANÇAIS 23 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT AVERTISSEMENT! Une mauvaise réparation de l'appareil peut entraîner un danger pour la sécurité de l'utilisateur. Toute réparation ne doit être effectuée que par un technicien qualifié. Reportez-vous au tableau ci-dessous pour obtenir plus d'informations sur les problèmes possibles. Pour certaines anomalies, l'écran affiche un code d'alarme. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé.
www.aeg.com Problème et code d'alarme Cause et solution possibles L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps. • Si vous avez sélectionné l'option de départ différé, annulez-le ou attendez la fin du décompte. • Activez l'option TimeSaver pour réduire la durée du programme. • Activer certaines options peut rallonger la durée du programme.
FRANÇAIS 25 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
www.aeg.com Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage spécialement conçus pour les lave-vaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après-vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ».
FRANÇAIS 27 Reportez-vous aux chapitres « Avant la première utilisation », « Utilisation quotidienne » ou « Conseils » pour connaître les autres causes probables. 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 850 / 610 Branchement électrique 1) Tension (V) 200 - 240 Fréquence (Hz) 50 / 60 bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude 2) max.
117872760-A-212018 www.aeg.