FFB93700PM EN PL USER MANUAL User Manual Dishwasher Instrukcja obsługi Zmywarka 2 26
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. If the appliance has ventilation openings in the base, they must not be covered e.g. by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets.
ENGLISH 5 2.5 Internal light WARNING! Risk of injury. WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance.
www.aeg.com 3.
ENGLISH 7 4. CONTROL PANEL 1 2 3 4 5 6 10 9 1 2 3 4 5 6 On/off button Program key Navigation key (up) Display Delay key MyFavourite key 4.1 Key behaviour Program key • Short press enters the programme list. Default programme: ECO. • Long press (3 sec.) when a programme is running will delete the programme. The display shows the default programme. • Press at the same time the keys Program and Back to activate or deactivate the option Child lock.
www.aeg.com 5.
ENGLISH Programme Degree of soil Type of load Programme phases Rinse&Hold 6) • All • Prewash 9 Options 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets . It automatically adjusts the temperature and the quantity of water, the energy consumption and the programme duration.
www.aeg.com Settings Values Description MyFavourite List of programmes Set your favourite daily programme. Refer to specific information provided in this chapter. AirDry ON (default value) OFF Set the automatic door opening for all programmes except Rinse&Hold. Refer to the specific information provided in this chapter. Brightness From level 0 to level 9. Change the brightness of the display. Contrast From level 0 to level 9. Change the contrast of the display.
ENGLISH 11 6.4 How to save the MyFavourite programme You can only save 1 programme at a time. A new setting cancels the previous one. 1. Press the Option key. 2. Select Settings. 3. Press the OK key. 4. Select MyFavourite. 5. Press the OK key. The display shows the programme list. 6. Select a programme. 7. Press the OK key. 8. The display shows Add option and Done. • Select Done if you want to save a programme without options and press the OK key.
www.aeg.com 7.1 Option list Options Values Description Delay start From 1 to 24 hours OFF (default value) Delay the start of the programme. XtraDry ON OFF (default value) Activate this option if you want to boost the drying performance. Refer to specific information provided in this chapter. ExtraHygiene ON OFF (default value) The use of this option sanitizes cutlery and tableware. During the last rinsing phase, the temperature stays at 70 °C for at least 10 minutes.
ENGLISH The washing results are the same as with the normal programme duration but the drying results can be less satisfactory. The TimeSaver option is not applicable to all programmes. 1. Scroll through the programme list and select a programme. 2. Press the OK key to confirm. If the TimeSaver option is applicable to the selected programme, the display shows the 2 conditions Fast and Normal and the programme duration for each condition: • Fast: TimeSaver activated. Press the OK key to confirm.
www.aeg.com German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level.
ENGLISH 8.3 The rinse aid dispenser CAUTION! Only use rinse aid specifically designed for dishwashers. The rinse aid helps to dry the dishes without streaks and stains. The rinse aid is automatically released during the hot rinse phase. It is possible to set the released quantity of rinse aid between level 1 (minimum quantity) and level 6 (maximum quantity). Level 0 deactivates the rinse aid dispenser and no rinse aid is released. Factory setting: level 4. 1. Open the lid (C). 2.
www.aeg.com CAUTION! Only use detergent specifically designed for dishwashers. 1. Press the release button (A) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (B). 3. If the programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance door. 4. Close the lid. Make sure that the lid locks into position. 9.
ENGLISH 17 2. Press and hold the Program key for about 3 seconds until the display shows Stop washing?. • Select Resume to continue with the countdown. Press the OK key to confirm. • Select Stop to cancel the delay start. Press the OK key to confirm. • Select Stop to cancel the running programme. Press the OK key to confirm. Make sure that there is detergent in the detergent dispenser before you start a new programme.
www.aeg.com we recommend that you use the tablets with long programmes. • Do not use more than the correct quantity of detergent. Refer to the instructions on the detergent packaging. 10.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase.
ENGLISH 19 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 1. Turn the filter (B) counterclockwise and remove it. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B). 3.
www.aeg.com 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 4. To engage again the spray arm to the basket, press the spray arm upwards in the direction indicated by the lower arrow and simultaneously turn it counterclockwise until it locks into place. 11.3 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes.
ENGLISH 21 12. TROUBLESHOOTING If the appliance does not start or it stops during operation, first check if you can solve the problem by yourself with the help of the information in the table or contact an Authorised Service Centre. WARNING! Repairs not properly done may result in serious risk to the safety of the user. Any repairs must be performed by qualified personnel. With some problems, the display shows an alarm code.
www.aeg.com Problem and alarm code Possible cause and solution The program lasts too long. • Select the TimeSaver option to shorten the program time. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown. The remaining time in the • This is not a defect. The appliance is working correctly. display increases and skips nearly to the end of program time. Small leak from the appliance door. • The appliance is not levelled.
ENGLISH 23 Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option XtraDry and set AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets.
www.aeg.com Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. The level of salt is low, check the refill indicator. The cap of the salt container is loose. Your tap water is hard.
ENGLISH appliances marked with the symbol with the household waste. Return the 25 product to your local recycling facility or contact your municipal office.
www.aeg.com SPIS TREŚCI 1. INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA............................................27 2. WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA.............................................28 3. OPIS URZĄDZENIA............................................................................................30 4. PANEL STEROWANIA....................................................................................... 31 5. PROGRAMY...............................................................................
POLSKI 1. 27 INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA Przed przystąpieniem do instalacji i rozpoczęciem eksploatacji urządzenia należy uważnie zapoznać się z załączoną instrukcją obsługi. Producent nie odpowiada za obrażenia ciała ani szkody spowodowane nieprawidłową instalacją lub eksploatacją urządzenia. Należy zachować instrukcję obsługi w bezpiecznym i łatwo dostępnym miejscu do wykorzystania w przyszłości. 1.
www.aeg.com do obsługi przez klientów w hotelach, motelach, obiektach noclegowych i innych obiektach mieszkalnych. Nie zmieniać parametrów technicznych urządzenia. Robocze ciśnienie wody (minimalne i maksymalne) musi mieścić się w granicach 0.5 (0.05) / 8 (0.8) barów (MPa) Maksymalna liczba kompletów wynosi 15. Jeśli przewód zasilający jest uszkodzony, ze względów bezpieczeństwa musi go wymienić producent, autoryzowane centrum serwisowe lub inna wykwalifikowana osoba.
POLSKI 2.2 Podłączenie do sieci elektrycznej OSTRZEŻENIE! Występuje zagrożenie pożarem i porażeniem prądem elektrycznym. • • • • • • • • • Urządzenie musi być uziemione. Upewnić się, że parametry na tabliczce znamionowej odpowiadają parametrom znamionowym źródła zasilania. Należy używać wyłącznie prawidłowo zamontowanego gniazda elektrycznego z uziemieniem. Nie stosować rozgałęźników ani przedłużaczy. Należy zwrócić uwagę, aby nie uszkodzić wtyczki ani przewodu zasilającego.
www.aeg.com 2.5 Wewnętrzne oświetlenie • OSTRZEŻENIE! Zagrożenie odniesieniem obrażeń. • • • Urządzenie jest wyposażone w oświetlenie wewnętrzne, które włącza się w momencie otwarcia drzwi i wyłącza po ich zamknięciu. Źródło światła zastosowane w urządzeniu nie jest odpowiednie do oświetlania pomieszczeń domowych. Aby wymienić oświetlenie, należy skontaktować się z autoryzowanym serwisem. 2.6 Serwis • Aby zlecić naprawę urządzenia, należy skontaktować się z autoryzowanym centrum serwisowym.
POLSKI 10 Dozownik detergentu 11 Dolny kosz 12 Górny kosz 31 13 Szuflada na sztućce 4. PANEL STEROWANIA 1 2 3 4 5 6 10 9 1 2 3 4 5 6 Przycisk wł./wył. Przycisk Program Przycisk nawigacji (w górę) Wyświetlacz Przycisk Delay Przycisk MyFavourite 8 7 7 8 9 10 4.1 Działanie przycisków Przycisk Program • Krótkie naciśnięcie powoduje wyświetlenie listy programów. Domyślny program: ECO. • Długie naciśnięcie (3 s) podczas trwania programu powoduje anulowanie programu.
www.aeg.com • Nacisnąć, aby uruchomić program lub opcję opóźnienia rozpoczęcia programu. Przycisk Back • Przejście do poprzedniego ekranu. Przyciski nawigacyjne • Przyciski służą do przewijania list i tekstu informacji. 5.
POLSKI Program Stopień zabrudze‐ nia Rodzaj załadunku Fazy programu Rinse&Hold 6) • • Dowolne 33 Opcje Zmywanie wstęp‐ ne 1) W tym programie uzyskuje się największą efektywność zużycia wody i energii elektrycznej podczas zmywania średnio zabrudzonych naczyń i sztućców. (Jest to standardowy program dla ośrodków prze‐ prowadzających testy). 2) Urządzenie rozpoznaje stopień zabrudzenia oraz ilość naczyń znajdujących się w koszach.
www.aeg.com 6. USTAWIENIA 6.1 Lista ustawień Aby wyświetlić listę ustawień, należy z poziomu listy opcji wybrać pozycję Ustawienia. Ustawienia Wartości Opis MyFavourite Lista programów Ustawienie ulubionego, często używanego progra‐ mu. Dokładne informacje podano w odpowiedniej części tego rozdziału. AirDry WŁ. (wartość domyśl‐ na) WYŁ. Ustawienie automatycznego otwierania drzwi we wszyst‐ kich programach z wyjątkiem Rinse&Hold.
POLSKI 6.2 Zmiana ustawienia obejmującego dwie wartości (WŁ. i WYŁ.) Po wprowadzeniu zmiany ustawienie pozostanie zachowane, nawet jeśli program zakończy się lub zostanie anulowany. 1. 2. 3. 4. 5. Nacisnąć przycisk Option. Wybrać Ustawienia. Nacisnąć przycisk OK. Wybrać zmieniane ustawienie. Nacisnąć przycisk OK, aby zmienić wartość z WŁ. na WYŁ. lub odwrotnie. 6. Kilkakrotnie nacisnąć przycisk Option, aż na wyświetlaczu pojawi się lista programów. 6.
www.aeg.com UWAGA! W przypadku obecności dzieci opcję AirDry można wyłączyć, aby drzwi pozostawały zamknięte po zakończeniu cyklu. Opcja AirDry włącza się automatycznie we wszystkich programach z wyjątkiem Rinse&Hold. Aby poprawić skuteczność suszenia, należy skorzystać z opcji XtraDry lub włączyć opcję AirDry. 7. OPCJE Żądane opcje należy zawsze włączać przed uruchomieniem programu. Opcji nie można włączać ani wyłączać w trakcie programu. Nie wszystkie opcje są ze sobą zgodne.
POLSKI godzin i ponownie nacisnąć przycisk OK w celu potwierdzenia. 4. Aby powrócić do listy programów, należy kilkakrotnie nacisnąć przycisk Option, aż na wyświetlaczu pojawi się wybrany program. 7.3 XtraDry Tę opcję należy włączyć, aby poprawić wydajność suszenia. Użycie tej opcji może wpłynąć na czas trwania niektórych programów, zużycie wody oraz temperaturę ostatniego płukania.
www.aeg.com Po uruchomieniu programu urządzenie zaczyna doprowadzać żywicę do zmiękczacza wody – może to potrwać do 5 minut. Może wydawać się, że urządzenie nie pracuje. Program rozpoczyna się dopiero po zakończeniu tego procesu. Proces ten jest powtarzany co pewien czas. 8.1 Zmiękczanie wody Zmiękczacz usuwa z wody substancje mineralne, które mogą mieć negatywny wpływ na efekty zmywania lub na pracę urządzenia. Im wyższa zawartość substancji mineralnych, tym twardsza jest woda.
POLSKI 2. Wlać 1 litr wody do zbiornika soli (tylko za pierwszym razem). 3. Napełnić zbiornik soli solą do zmywarek. 39 ilość). Poziom 0 oznacza wyłączenie dozownika płynu nabłyszczającego oraz dozowania. Ustawienie fabryczne: poziom 4. Napełnianie dozownika płynu nabłyszczającego A B 4. Usunąć sól rozsypaną wokół otworu zbiornika soli. C 5. Obrócić pokrywkę zbiornika soli w prawo, aby zamknąć zbiornik soli. Podczas napełniania zbiornika soli może się z niego wydostawać woda i sól.
www.aeg.com jest zadowalająca, można wyłączyć wskaźnik uzupełniania płynu nabłyszczającego, ustawiając poziom płynu nabłyszczającego na 0. W celu zapewnienia lepszych efektów suszenia zaleca się stałe stosowanie płynu nabłyszczającego, także w połączeniu z tabletkami wieloskładnikowymi zawierającymi środek nabłyszczający. 9. CODZIENNA EKSPLOATACJA 1. Odkręcić zawór wody. 2. Nacisnąć przycisk wł./wył., aby włączyć urządzenie. Upewnić się, że urządzenie jest w trybie wyboru programu.
POLSKI Jeśli dany program działa z opcją TimeSaver, należy wybrać pozycję Szybki lub Normalny. 4. Zamknąć drzwi urządzenia, aby uruchomić program Anulowanie opóźnienia rozpoczęcia programu Funkcji opóźnienia rozpoczęcia programu nie można ustawić z programem MyFavourite. 1. Ustawić program. 2. Nacisnąć przycisk Delay. Czas opóźnienia jest widoczny w prawym górnym rogu wyświetlacza. 3. Nacisnąć kilkakrotnie przycisk Delay, aby zwiększyć liczbę godzin opóźnienia rozpoczęcia programu.
www.aeg.com 10. WSKAZÓWKI I PORADY 10.1 Informacje ogólne • Stosowanie się do poniższych wskazówek pozwoli zapewnić optymalne efekty zmywania i suszenia podczas codziennej eksploatacji oraz przyczyni się do ochrony środowiska. • • • • • • Większe resztki żywności z naczyń należy wyrzucić do kosza. Nie opłukiwać naczyń ręcznie. W razie potrzeby użyć programu zmywania wstępnego (jeśli jest dostępny) lub wybrać program z fazą zmywania wstępnego. Należy zawsze wykorzystywać całą pojemność koszy.
POLSKI ani nie umieszczać naczyń w koszach. 4. Po zakończeniu programu ustawić stopień zmiękczania wody odpowiednio do twardości wody doprowadzanej do urządzenia. 5. Wyregulować dozowanie płynu nabłyszczającego. 6. Włączyć funkcję powiadomienia o konieczności uzupełnienia płynu nabłyszczającego. 10.5 Przed rozpoczęciem programu Upewnić się, że: • • • • 10.4 Ładowanie koszy • • • • • • • • • • W urządzeniu należy zmywać przedmioty przystosowane do zmywania w zmywarkach.
www.aeg.com C B A 1. Obrócić filtr (B) przeciwnie do ruchu wskazówek zegara i wyjąć go. 2. Wyjąć filtr (C) z filtra (B). 3. Wyjąć filtr płaski (A). 4. Umyć filtry. 5. Upewnić się, że wokół krawędzi osadnika nie znajdują się resztki żywności ani zanieczyszczenia. 6. Włożyć na miejsce filtr płaski (A). Upewnić się, że jest prawidłowo umieszczony pod 2 prowadnicami. 7. Włożyć filtry (B) i (C). 8. Włożyć filtr (B) do filtra płaskiego (A). Obrócić zgodnie z ruchem wskazówek zegara, aż się zablokuje.
POLSKI 45 UWAGA! Nieprawidłowe umiejscowienie filtrów może skutkować niezadowalającymi efektami zmywania i uszkodzeniem urządzenia. 11.2 Czyszczenie ramion spryskujących Nie wolno wyjmować ramion spryskujących. Jeżeli otwory w ramionach spryskujących są zatkane, zabrudzenia należy usunąć za pomocą cienkiego, spiczastego przedmiotu. 11.3 Czyszczenie górnego ramienia spryskującego 4.
www.aeg.com w miesiącu specjalnego środka czyszczącego do zmywarek. Należy ściśle przestrzegać wskazówek umieszczonych na opakowaniu produktu. 12. ROZWIĄZYWANIE PROBLEMÓW Jeśli urządzenia nie można uruchomić lub przestaje ono działać podczas pracy, należy najpierw sprawdzić, czy problem można rozwiązać samodzielnie, korzystając z informacji zawartych w tabeli, lub skontaktować się z autoryzowanym centrum serwisowym. Przy niektórych usterkach na wyświetlaczu pojawia się kod alarmowy.
POLSKI Problem i kod alarmowy Możliwa przyczyna i rozwiązanie Włączyło się zabezpieczenie • przed zalaniem. Na wyświetlaczu widoczne jest wskazanie 47 Zakręcić zawór wody i skontaktować się z autoryzowa‐ nym centrum serwisowym. . Urządzenie wielokrotnie przerywa i wznawia pracę. • Jest to normalne zjawisko. Zapewnia to optymalne efek‐ ty zmywania i oszczędność energii. Program trwa zbyt długo. • Wybrać opcję TimeSaver, aby skrócić czas trwania pro‐ gramu.
www.aeg.com 12.1 Efekty zmywania i suszenia są niezadowalające Problem Możliwa przyczyna i rozwiązanie Niezadowalające efekty zmy‐ wania. • • • Niezadowalające efekty su‐ szenia. • • • • • Białawe smugi lub niebieska‐ wy nalot na szklankach i na‐ czyniach. • • Patrz punkty „Codzienna eksploatacja”, „Wskazów‐ ki i porady” oraz broszura dotycząca załadunku ko‐ szy. Używać programów zapewniających bardziej inten‐ sywny cykl zmywania. Wyczyścić ramię spryskujące i filtr.
POLSKI Problem Możliwa przyczyna i rozwiązanie Ślady rdzy na sztućcach. • • Po zakończeniu programu w • dozowniku znajdują się pozos‐ tałości detergentu. • • 49 W wodzie używanej do zmywania jest zbyt dużo soli. Patrz „Zmiękczacz wody”. Umieszczono razem sztućce ze srebra i stali nie‐ rdzewnej. Należy unikać umieszczania blisko siebie sztućców ze srebra i stali nierdzewnej. Tabletka z detergentem zablokowała się w dozowniku i woda nie wypłukała jej całkowicie.
www.aeg.com 13. DANE TECHNICZNE Wymiary Szerokość / wysokość / głębokość 596 / 850 / 610 (mm) Podłączenie do sieci elek‐ Napięcie (V) 200 - 240 trycznej 1) Częstotliwość (Hz) 50 / 60 Ciśnienie doprowadzanej wo‐ bar (minimalne i maksymalne) dy MPa (minimalne i maksymalne) 0.5 - 8 Dopływ wody Zimna lub ciepła woda 2) maks. 60°C Pojemność Liczba kompletów 15 Pobór mocy Tryb czuwania (W) 5.0 Pobór mocy Tryb wyłączenia (W) 0.10 0.05 - 0.
POLSKI 51
117882552-A-322017 www.aeg.