FFS52610ZW USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................5 4. CONTROL PANEL....................................................................................................... 6 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. If the appliance has ventilation openings in the base, they must not be covered e.g. by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets.
ENGLISH WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is complete.
www.aeg.com 5 6 7 8 9 Rating plate Salt container Air vent Rinse aid dispenser Detergent dispenser 10 Cutlery basket 11 Lower basket 12 Upper basket 4. CONTROL PANEL 1 2 8 1 2 3 4 5 On/off button Program button Programme indicators Display Delay button 3 4 7 5 6 6 Option button 7 Indicators 8 Start button 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Rinsing phase. It comes on when the rinsing phase operates. Drying phase.
ENGLISH Indicator 7 Description TimeSaver indicator. XtraDry indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. Delay indicator. Door indicator. It comes on when the appliance door is open or is not correctly closed. 5.
www.aeg.com 5.1 Consumption values Programme 1) Water (l) Energy (kWh) Duration (min) 9.9 0.921 240 7 - 12 0.7 - 1.5 45 - 160 13-15 1.4 - 1.6 140 - 160 9 0.8 30 13 - 14 0.9 - 1.1 70 - 85 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes For all the necessary information for test performance, send an email to: info.test@dishwasher-production.
ENGLISH 9 Water hardness German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
www.aeg.com How to deactivate the rinse aid empty notification During the drying phase, the door opens automatically and remains ajar. The appliance must be in programme selection mode. 1. To enter the user mode, press and hold simultaneously Delay and Option until the indicators , and start flashing and the display is blank. 2. Press Start. • The indicators off. and are still • The indicator flashes. • The display shows the current setting. – = rinse aid empty notification activated.
ENGLISH Not all options are compatible with each other. If you have selected non compatible options, the appliance will automatically deactivate one or more of them. Only the indicators of the options still active will stay on. 7.1 XtraDry Activate this option to boost the drying performance. With XtraDry on, the duration of some programmes, water consumption and the last rinse temperature can be affected.
www.aeg.com How to fill the salt container 1. Turn the cap of the salt container counterclockwise and remove it. 2. Put 1 litre of water in the salt container (Only for the first time). 3. Fill the salt container with dishwasher salt. 8.2 How to fill the rinse aid dispenser A D B C B A 4. Remove the salt around the opening of the salt container. M AX 4 1 3 2 + - C D 5. Turn the cap of the salt container clockwise to close the salt container.
ENGLISH Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil. 9.1 Using the detergent D A B 13 9.
www.aeg.com Opening the door while the appliance operates Opening the door while a programme is running stops the appliance. It may affect the energy consumption and the programme duration. After closing the door, the appliance continues from the point of interruption. If the door is opened for more than 30 seconds during the drying phase, the running programme ends. It does not happen if the door is opened by AirDry function.
ENGLISH 10.2 Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance. • In areas with hard and very hard water we recommend to use plain dishwasher detergent (powder, gel, tablets containing no additional agents), rinse aid and salt separately for optimal cleaning and drying results. • At least once a month run the appliance with the use of appliance cleaner which is particularly suitable for this purpose.
www.aeg.com 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. 4. Wash the filters. 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A).
ENGLISH 17 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 11.4 Internal cleaning CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object.
www.aeg.com Problem and alarm code Possible cause and solution The program does not start. • Make sure that the appliance door is closed. • Press Start. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to recharge the resin inside the water softener. The duration of the procedure is approximately 5 minutes. The appliance does not fill with water. • Make sure that the water tap is open.
ENGLISH 19 Problem and alarm code Possible cause and solution The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use. • Internal electrical fault of the appliance. Contact an Authorised Service Centre. Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes.
www.aeg.com Problem Possible cause and solution The dishes are wet. • For the best drying performance activate the option XtraDry and set AirDry . • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together.
ENGLISH 21 Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. 13. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 600 / 850 / 625 Electrical connection 1) Voltage (V) 200 - 240 Frequency (Hz) 50 / 60 Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 5.0 Power consumption Off-mode (W) 0.
www.aeg.
ENGLISH 23
156914730-A-062017 www.aeg.