FSB52610Z NL EN ET USER MANUAL Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Kasutusjuhend Nõudepesumasin 2 25 47
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE......................................................................................... 3 2. VEILIGHEIDSVOORSCHRIFTEN.................................................................................4 3. BESCHRIJVING VAN HET PRODUCT........................................................................6 4. BEDIENINGSPANEEL................................................................................................. 7 5. PROGRAMMA´S..................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • • • • • De specificatie van het apparaat mag niet worden veranderd. De waterdruk (minimaal en maximaal) moet liggen tussen 0.5 (0.05) / 8 (0.8) bar (MPa) Houd rekening met het maximale aantal 13 plaatsen. Als de voedingskabel beschadigd is, moet de fabrikant, een erkende serviceverlener of een gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen.
NEDERLANDS • Dit apparaat moet worden aangesloten op een geaard stopcontact. • Zorg ervoor dat de parameters op het vermogensplaatje overeenkomen met elektrische vermogen van de netstroom. • Gebruik altijd een juist geïnstalleerd schokbestendig stopcontact. • Gebruik geen meerwegstekkers en verlengsnoeren. • Zorg dat u de hoofdstekker en kabel niet beschadigt. Indien de voedingskabel moet worden vervangen, dan moet dit gebeuren door onze Klantenservice.
www.aeg.com • Haal de stekker uit het stopcontact. • Snij het netsnoer van het apparaat af en gooi dit weg. • Verwijder de deurgreep om te voorkomen dat kinderen en huisdieren opgesloten raken in het apparaat. 3. BESCHRIJVING VAN HET PRODUCT 1 2 11 10 1 2 3 4 5 6 9 8 7 Bovenste sproeiarm Onderste sproeiarm Filters Typeplaatje Zoutreservoir Luchtopening 3.1 Beam-on-Floor De Beam-on-Floor is een lichtstraal die op de vloer onder de deur van het apparaat verschijnt.
NEDERLANDS 4. BEDIENINGSPANEEL 1 1 2 3 4 5 2 Aan/uit-toets Weergave Delay-toets Programmakeuzetoets (omhoog) Programmakeuzetoets (omlaag) 3 4 6 7 8 9 5 6 7 8 9 TimeSaver-toets XtraDry-toets RESET-toets Indicatielampjes 4.1 Indicatielampjes Aanduiding Beschrijving Glansmiddelindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. 5.
www.aeg.com Programma Mate van vervuiling Type lading Programmafasen Opties P4 • Pas bevuild • Serviesgoed en bestek • Wassen 60 °C of 65 °C • Spoelingen • XtraDry • Normaal of licht bevuild • Teer serviesgoed en glaswerk • Wassen 45 °C • Spoelingen • Drogen • XtraDry 3) P5 1) Dit programma biedt het meest efficiënte water- en energieverbruik voor normaal vervuild serviesgoed en bestek. Dit is het standaard programma voor testinstituten.
NEDERLANDS 9 6. INSTELLINGEN 6.1 Programmakeuzemodus en gebruikersmodus Als het apparaat in de programmakeuzemodus staat, kan een programma worden ingesteld en de gebruikersmodus worden ingevoerd. Houd tegelijkertijd RESET ingedrukt tot het apparaat in de programmakeuzemodus staat. Gebruikersmodus ingaan Instellingen die in de gebruikersmodus beschikbaar zijn: • Het niveau van de waterverzachter afgestemd op de waterhardheid.
www.aeg.com Duitse hardheid (°dH) Franse hardheid (°fH) mmol/l Clarke-graden Wateronthardingsniveau 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Fabrieksinstelling. 2) Gebruik geen zout op dit niveau. Stel ongeacht het gebruikte soort wasmiddel het juiste waterhardheidniveau in om de bijvulindicator voor zout geactiveerd te houden.
NEDERLANDS Na het beëindigen van het programma klinkt er tevens een geluidssignaal. Dit geluidssignaal is standaard uitgeschakeld, maar kan worden geactiveerd. Het geluidssignaal voor het einde van het programma inschakelen Zorg dat het apparaat in de gebruikersmodus staat. 1. Druk op LET OP! Probeer de deur van het apparaat niet binnen 2 minuten na automatisch openen te sluiten. Dit kan het apparaat beschadigen. AirDry wordt automatisch bij alle programma´s geactiveerd, behalve bij .
www.aeg.com 7. OPTIES De gewenste opties moeten elke keer dat u een programma start worden geactiveerd. De opties kunnen niet worden in- of uitgeschakeld als een programma in werking is. Niet alle opties kunnen met elkaar worden gecombineerd. Als u opties hebt geselecteerd die niet met elkaar te combineren zijn, dan schakelt het apparaat automatisch één of meerdere opties uit. Alleen de indicatielampjes van de actieve opties zijn aan.
NEDERLANDS de waterhardheid in uw omgeving. Indien niet, stel dan de stand van de waterontharder juist in. 2. Vul het zoutreservoir. 3. Vul het glansmiddeldoseerbakje. 4. Draai de waterkraan open. 5. Start een programma om resten te verwijderen die misschien nog in het apparaat zijn achtergebleven. Gebruik geen afwasmiddel en belaad de manden niet. Na het starten van een programma, doet het apparaat er ongeveer 5 minuten over om de hars in de waterontharder te herladen.
www.aeg.com LET OP! Gebruik alleen glansmiddel voor vaatwassers. 1. Druk op de ontgrendelknop (D) om de deksel te openen (C). 2. Giet het glansmiddel in het doseervakje (A) tot de vloeistof het niveau 'max' heeft bereikt. 3. Verwijder gemorst glansmiddel met een absorberend doekje om te voorkomen dat er te veel schuim ontstaat. 4. Sluit het deksel. Zorg ervoor dat het ontgrendelknopje op zijn plaats dichtklikt.
NEDERLANDS Een programma starten 1. Laat de deur op een kier staan. 2. Druk op de aan/uit-knop om het apparaat te activeren. Zorg dat het apparaat in de keuzemodus Programma staat. 3. Druk herhaaldelijk op of tot het display het nummer van het gekozen programma weergeeft. Het nummer van het programma worden circa 3 seconden op het display weergegeven en toont daarna de programmaduur. 4. Stel de bruikbare opties in. 5. Sluit de deur van de afwasmachine om het programma te starten.
www.aeg.com 10. AANWIJZINGEN EN TIPS 10.1 Algemene Volg de onderstaande tips om te zorgen voor optimale schoonmaak- en droogresultaten en ook het milieu te helpen beschermen. • Verwijder grotere etensresten van de borden en gooi ze in de vuilnisbak. • Spoel de vaat niet eerst af. Kies indien nodig een programma met voorwasfase. • Gebruik altijd de hele ruimte van de mandjes. • Zorg ervoor dat de vaat in de manden elkaar niet raakt of overlapt.
NEDERLANDS • Zorg er voor dat de sproeiarm vrij kan ronddraaien voordat u een programma start. 10.5 Voor het starten van een programma Zorg er, voordat u het gekozen programma start, voor dat: • De filters schoon zijn en correct zijn geplaatst. • De dop van het zoutreservoir goed dicht zit. • De sproeiarmen niet zijn verstopt. • Er regenereerzout en glansmiddel is toegevoegd (tenzij u gecombineerde afwastabletten gebruikt). • De positie van de items in de mandjes correct is.
www.aeg.com 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3. Verwijder de platte filter (A). 4. Was de filters. LET OP! Een onjuiste plaatsing van de filters kan leiden tot slechte wasresultaten en het apparaat beschadigen. 11.2 De sproeiarmen reinigen Probeer niet de sproeiarmen te verwijderen. Als etensresten de openingen in de sproeiarmen hebben verstopt, verwijder deze dan met een smal en puntig voorwerp.
NEDERLANDS schoonmaakproduct voor vaatwasmachines te gebruiken. Volg 19 de instructies op de verpakking van de producten zorgvuldig op. 12. PROBLEEMOPLOSSING Als het apparaat niet start of stopt tijdens de bediening, kijk dan of u het probleem zelf kunt oplossen met behulp van de informatie in de tabel of door contact op te nemen met een erkend servicecentrum. WAARSCHUWING! Niet juist uitgevoerde reparaties kunnen de veiligheid van de gebruiker ernstig in gevaar brengen.
www.aeg.com Probleem en alarmcode Mogelijke oorzaak en oplossing De anti-overstromingsbevei- • Draai de waterkraan dicht en neem contact op met de liging is ingeschakeld. service-afdeling. Op het display verschijnt . Het apparaat stopt en start meerdere keren tijdens de werking. • Dat is normaal. Het voorziet in optimale reinigingsresultaten en energiebesparing. Het programma duurt te lang. • Kies de optie TimeSaver om de programmaduur te verkorten.
NEDERLANDS 21 12.1 De was- en droogresultaten zijn niet naar tevredenheid Probleem Mogelijke oorzaak en oplossing Slechte wasresultaten. • Raadpleeg "Dagelijks gebruik", "Aanwijzingen en tips" en de folder voor het laden van de korf. • Gebruik intensievere wasprogramma´s. • Maak de inspuiters van de sproeiarm en het filter schoon. Zie "Onderhoud en reiniging". Slechte droogresultaten. • Serviesgoed heeft te lang in het gesloten apparaat gestaan.
www.aeg.com Probleem Mogelijke oorzaak en oplossing Roestresten op bestek. • Er wordt voor het wassen teveel zout in het water gebruikt. Zie 'De waterontharder instellen'. • Zilver en roestvrijstalen bestek zijn samen geplaatst. Zet zilveren en roestvrijstalen voorwerpen niet dicht bij elkaar. Er bevinden zich aan het einde • De vaatwastablet raakte klem in het vaatwasmiddeldovan het programma resten van seerbakje en is daardoor niet volledig weggespoeld vaatwasmiddel in het vaatwasdoor het water.
NEDERLANDS Energie-efficiëntieklasse A++ Energieverbruik in kWh per jaar, gebaseerd op 280 standaardcycli met toevoer van koud water en het verbruik in de energiebesparende standen. Het werkelijke energieverbruik wordt bepaald door de wijze waarop het apparaat wordt gebruikt 262 Energieverbruik van standaard reinigingscyclus (kWh) 0.921 Het elektriciteitsverbruik in de uit-stand (W) 0.50 Het elektriciteitsverbruik in de sluimerstand (W) 5.
www.aeg.com volksgezondheid te beschermen en recycle het afval van elektrische en elektronische apparaten. Gooi apparaten gemarkeerd met het symbool niet weg met het huishoudelijk afval. Breng het product naar het milieustation bij u in de buurt of neem contact op met de gemeente.
ENGLISH 25 CONTENTS 1. SAFETY INFORMATION........................................................................................... 25 2. SAFETY INSTRUCTIONS...........................................................................................27 3. PRODUCT DESCRIPTION.........................................................................................29 4. CONTROL PANEL..................................................................................................... 30 5. PROGRAMMES..........
www.aeg.com manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
ENGLISH • • • • • • • 27 If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
www.aeg.com • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. • UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses.
ENGLISH 3. PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 9 8 7 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 Beam-on-Floor The Beam-on-Floor is a light that is displayed on the floor below the appliance door. • When the programme starts, a red light comes on and stays on for the duration of the programme. • When the programme is completed, a green light comes on. • When the appliance has a malfunction, the red light flashes.
www.aeg.com 4. CONTROL PANEL 1 1 2 3 4 5 2 On/off button Display Delay button Programme button (up) Programme button (down) 3 4 6 7 8 9 5 6 7 8 9 TimeSaver button XtraDry button RESET button Indicators 4.1 Indicators Indicator Description Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. 5. PROGRAMMES The numbering of the programmes in the table (P1, P2, etc.) reflects their sequence on the control panel.
ENGLISH Programme Degree of soil Type of load Programme phases Options P4 • Fresh soil • Crockery and cutlery • Wash 60 °C or 65 °C • Rinses • XtraDry • Normal or light soil • Delicate crockery and glassware • Wash 45 °C • Rinses • Dry • XtraDry 3) P5 31 1) This programme offers the most efficient use of water and energy consumption for crockery and cutlery with normal soil. This is the standard programme for test institutes.
www.aeg.com 6. SETTINGS 6.1 Programme selection mode and user mode Press and hold RESET until the appliance is in programme selection mode. When the appliance is in programme selection mode it is possible to set a programme and to enter the user mode. How to enter user mode Settings available in the user mode: • The level of water softener according to the water hardness. • Activation or deactivation of the acoustic signal for the end of a programme.
ENGLISH 33 German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level. Regardless of the type of detergent used, set the proper water hardness level to keep the salt refill indicator active. Multi-tabs containing salt are not effective enough to soften hard water. How to set the water softener level Make sure the appliance is in user mode. 1. Press . • The indicators are off.
www.aeg.com – – = Acoustic signal off. = Acoustic signal on. 2. Press to change the setting. 3. Press on/off to confirm the setting. 6.5 AirDry AirDry improves the drying results with less energy consumption. AirDry is automatically activated with all programmes excluding applicable). (if To improve the drying performance refer to the XtraDry option or activate AirDry. CAUTION! If children have access to the appliance, it is advised to deactivate AirDry as opening the door may pose a danger.
ENGLISH XtraDry is a permanent option for all programmes other than and need not to be selected at every cycle. In the other programmes the setting of XtraDry is permanent and it is automatically used in next cycles. This configuration can be changed at any time. Every time is activated, XtraDry is off and needs to be chosen manually. 35 2. Press . The related indicator is on. The display shows the updated programme duration. 7.
www.aeg.com B A M AX 4 4. Carefully shake the funnel by its handle to get the last granules inside. 5. Remove the salt around the opening of the salt container. 6. Turn the cap of the salt container clockwise to close the salt container. CAUTION! Water and salt can come out of the salt container when you fill it. After you fill the salt container, immediately start a programme to prevent corrosion. 8.2 How to fill the rinse aid dispenser A D B C 9. DAILY USE 1. Open the water tap.
ENGLISH 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil. 9.1 Using the detergent 20 The function comes into operation: • 5 minutes after the completion of the programme.
www.aeg.com the energy consumption and the programme duration. After closing the door, the appliance continues from the point of interruption. Press and hold RESET until the appliance is in programme selection mode. Cancelling the programme If the door is opened for more than 30 seconds during the drying phase, the running programme ends. It does not happen if the door is opened by AirDry function. Press and hold RESET until the appliance is in programme selection mode.
ENGLISH • Detergent tablets do not fully dissolve with short programmes. To prevent detergent residues on the tableware, we recommend that you use the tablets with long programmes. • Do not use more than the correct quantity of detergent. Refer to the instructions on the detergent packaging. 10.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2.
www.aeg.com 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 1. Turn the filter (B) counterclockwise and remove it. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B).
ENGLISH 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 41 • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance.
www.aeg.com Problem and alarm code Possible cause and solution The appliance does not fill with water. • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the filter in the inlet hose is not clogged. • Make sure that the inlet hose has no kinks or bends. The display shows or . The appliance does not drain the water.
ENGLISH Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes. Once you have checked the appliance, deactivate and activate the appliance. If 43 the problem occurs again, contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre. 12.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results.
www.aeg.com Problem Possible cause and solution Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener". • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together. There are residues of detergent in the dispenser at the end of the programme. • The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
ENGLISH 45 Energy consumption in kWh per year, based on 280 standard clean- 262 ing cycles using cold water fill and the consumption of the low power modes. The actual energy consumption will depend on how the appliance is used. Energy consumption of standard cleaning cycle (kWh) 0.921 Power consumption in off mode (W) 0.50 Power consumption in left-on mode (W) 5.0 Water consumption in litres per year, based on 280 standard clean2775 ing cycles.
www.aeg.com product to your local recycling facility or contact your municipal office.
EESTI 47 SISUKORD 1. OHUTUSINFO.................................................................................................... 48 2. OHUTUSJUHISED..............................................................................................49 3. SEADME KIRJELDUS........................................................................................ 51 4. JUHTPANEEL.....................................................................................................52 5. PROGRAMMID.....................
1. www.aeg.com OHUTUSINFO Enne seadme paigaldamist ja kasutamist lugege kaasasolev juhend tähelepanelikult läbi. Tootja ei võta endale vastutust vigastuste või varalise kahju eest, mis on tingitud paigaldusnõuete eiramisest või väärast kasutusest. Hoidke kasutusjuhend kindlas kohas alles, et saaksite seda vajadusel vaadata. 1.
EESTI • • • • • • • • 49 Järgige kohalikku maksimaalset 13 taset. Kui toitejuhe on vigastatud, laske see ohutuse mõttes välja vahetada tootja, selle volitatud hooldekeskuses või lihtsalt kvalifitseeritud isiku poolt. Pange söögiriistad söögiriistade korvi teravama otsaga allapoole või horisontaalasendis söögiriistade sahtlisse teravama servaga allapoole. Ärge jätke seadme ust lahti, kui selle juurest ära lähete, sest keegi võib kogemata ukse taha komistada.
www.aeg.com 2.3 Veeühendus • • • • • • Vältige veevoolikute kahjustamist. Enne ühendamist uute või pikalt kasutamata torudega või pärast parandustöid või uute seadeldiste (nt veemõõdikute) paigaldamist laske veel mõnda aega voolata, kuni see on puhas ja selge. Seadme esmakordsel kasutamisel ja pärast seda kontrollige, ega kuskil pole lekkeid. Vee sisselaskevoolikul on kaitseklapp ja kattega sisemine toitejuhe. • • • Nõudepesumasina pesuained on ohtlikud.
EESTI 3. SEADME KIRJELDUS 1 2 11 10 1 2 3 4 5 6 9 8 7 Ülemine pihustikonsool Alumine pihustikonsool Filtrid Andmeplaat Soolamahuti Ventilatsiooniava 3.1 Beam-on-Floor Beam-on-Floor on tuli, mis kuvatakse seadme ukse ette põrandale. • • • Kui programm käivitub, süttib punane tuli, mis põleb kuni programmi lõppemiseni. Kui programm on lõppenud, süttib roheline tuli. Seadme rikke korral punane tuli vilgub.
www.aeg.com 4. JUHTPANEEL 1 1 2 3 4 5 2 Sisse/välja-nupp Ekraan Delay-nupp Programminupp (üles) Programminupp (alla) 3 4 6 7 8 9 5 6 7 8 9 TimeSaver-nupp XtraDry-nupp RESET-nupp Indikaatorid 4.1 Indikaatorid Indikaator Kirjeldus Loputusvahendi indikaator. Programmi töötamise ajal on see indikaator alati väljas. Soolaindikaator. Programmi töötamise ajal on see indikaator alati väljas. 5. PROGRAMMID Tabelis olevad programmide numbrid (P1, P2 jne) näitavad nende järjekorda juhtpaneelil.
EESTI Programm Määrdumisaste Nõude tüüp Programmi faasid Valikud P4 • • • Pesu 60 °C või 65 °C Loputused • XtraDry Pesu 45 °C Loputused Kuivatamine • XtraDry 3) P5 • • • Värske määrdu‐ mine Lauanõud ja söögiriistad Tavaline või ker‐ • ge määrdumine • Õrnad lauanõud • ja klaas 53 1) See programm tarbib tavalise määrdumisastmega lauanõude ja söögiriistade pesemiseks vett ja ener‐ giat kõige efektiivsemalt. See on standardprogramm testimisasutustele.
www.aeg.com 6. SEADED 6.1 Programmi valiku režiim ja kasutajarežiim ei ole, valige programmi valimise režiim järgmiselt: Kui seade on programmi valimise režiimis, saab valida sobiva programmi ja sisestada kasutajarežiimi. Kasutajarežiimi puhul saadaolevad valikud: • Veepehmendaja taset vastavalt vee karedusele. • Programmi lõppu tähistavate helisignaalide sisse- või väljalülitamist. • Tühja loputusvahendi jaoturi märguande sisse- või väljalülitamist. • Valiku AirDry sisse- või väljalülitamist.
EESTI 55 Saksa kraadid (°dH) Prantsuse kraadid (°fH) mmol/l Clarke'i kraadid Veepehmendaja ta‐ se <4 <7 <0.7 <5 1 2) 1) Tehaseseade. 2) Selle taseme puhul ärge soola kasutage. Olenemata kasutatavast pesuainest valige õige veekareduse tase, et hoida soolamahuti täitmise indikaatorit sisselülitatult. Soola sisaldavad multitabletid ei ole kareda vee pehmendamiseks piisavalt tõhusad. Tühja loputusvahendi jaoturi märguande väljalülitamine Veenduge, et seade on kasutajarežiimis. 1.
www.aeg.com – – = helisignaal on väljas. = helisignaal on sees. 2. Seade muutmiseks vajutage . 3. Seade kinnitamiseks vajutage sisse/ välja-nuppu. AirDry lülitatakse sisse automaatselt kõigi programmidega, välja arvatud (kui see on olemas). Paremate kuivatustulemuste saamiseks valige XtraDry või lülitage AirDry sisse. ETTEVAATUST! Kui lapsed võivad seadme juurde pääseda, tuleks AirDry välja lülitada, sest seadme avatud uks võib endast ohtu kujutada. 6.
EESTI XtraDry on püsivalik kõigi programmide puhul, välja arvatud , ning seda pole tarvis iga kord eraldi valida. Muude programmide puhul on valik XtraDry püsiv ja seda kasutatakse automaatselt ka järgmistes tsüklites. Seda seadistust saab alati muuta. Programmi igakordsel sisselülitamisel on XtraDry välja lülitatud ja see tuleb valida käsitsi. 2. Vajutage . Vastav indikaator põleb. Ekraan näitab programmi uuendatud kestust. 7.2 TimeSaver See valik tõstab veesurvet ja temperatuuri.
www.aeg.com B A M AX 4 ETTEVAATUST! Vesi ja sool võivad soolamahutist täitmise ajal välja tulla. Rooste ärahoidmiseks käivitage programm kohe pärast soolamahuti täitmist. - C D 4. Raputage kergelt lehtrit, et kõik soolagraanulid mahutisse juhtida. 5. Eemaldage sool soolamahuti avause ümbert. 6. Soolamahuti sulgemiseks keerake soolamahuti korki päripäeva. 1 3 2 + ETTEVAATUST! Kasutage vaid nõudepesumasina jaoks mõeldud loputusvahendit. 1. Vajutage avamisnuppu (D), et avada kaas (C). 2.
EESTI Veenduge, et seade on programmi valimise režiimis. • Kui soolaindikaator põleb, täitke soolamahuti. • Kui loputusvahendi indikaator põleb, täitke loputusvahendi jaotur. 3. Pange nõud korvidesse. 4. Lisage pesuaine. 5. Määrake ja käivitage nõude tüübile ja määrdumisastmele vastav programm. 9.1 Pesuaine kasutamine 20 Funktsioon käivitub: • 5 minutit pärast pesuprogrammi lõppu. • Kui 5 minuti jooksul ei ole programm käivitunud. 3.
www.aeg.com uuesti sulgete, jätkub seadme töö kohast, kus see katkes. Vajutage ja hoidke RESET, kuni seade jõuab programmi valimise režiimi. Kui kuivatusfaasi ajal avatakse uks kauemaks kui 30 sekundit, lülitub käimasolev programm välja. Seda ei juhtu juhul, kui uks avatakse funktsiooniga AirDry. Programmi tühistamine Pärast ukse automaatset avanemist funktsiooniga AirDry ärge üritage seda esimese 2 minuti jooksul sulgeda, sest see võib seadet kahjustada.
EESTI 10.3 Kuidas lõpetada multitablettide kasutamine Enne pesuaine, soola ja loputusvahendi eraldi kasutamist tehke järgmist. 1. Valige kõrgeim veepehmendaja tase. 2. Veenduge, et soolamahuti ja loputusvahendi jaotur on täis. 3. Käivitage lühim loputusfaasiga programm. Ärge kasutage pesuainet ega pange midagi korvidesse. 4. Kui pesuprogramm on lõppenud, kohandage veepehmendaja vastavalt oma piirkonna vee karedusele. 5. Reguleerige eraldatava loputusvahendi kogust. 6.
www.aeg.com C B A 1. Pöörake filtrit (B) vastupäeva ja võtke välja. 2. Eemaldage filter (C) filtrist (B). 3. Eemaldage lame filter (A). 4. Peske filtrid puhtaks. 5. Veenduge, ega settevanni äärte ümber pole kogunenud toidujäätmeid või mustust. 6. Asetage lame filter (A) tagasi. Veenduge, et see paikneb õigesti kahe juhiku all. 7. Pange uuesti kokku filtrid (B) ja (C). 8. Pange tagasi filter (B) lameda filtri sees (A). Keerake päripäeva, kuni see kohale lukustub.
EESTI ETTEVAATUST! Filtrite ebaõige asend võib põhjustada kehva pesutulemust ja kahjustada seadet. 11.2 Pihustikonsoolide puhastamine 11.3 Välispinna puhastamine • Puhastage seadet pehme niiske lapiga. Kasutage ainult neutraalseid pesuaineid. Ärge kasutage abrasiivseid tooteid, küürimisšvamme ega lahusteid. 11.4 Sisemuse puhastamine • • Ärge pihustikonsoole eemaldage. Kui pihustikonsoolide avad on ummistunud, eemaldage mustus peenikese teravaotsalise esemega.
www.aeg.com Probleem ja veakood Võimalik põhjus ja lahendus Seade ei tühjene veest. • • • • Ekraanil kuvatakse . Üleujutusvastane seade töö‐ • tab. Ekraanil kuvatakse Veenduge, et valamu äravool ei ole ummistunud. Veenduge, et tühjendusvooliku filter ei ole ummistunud. Veenduge, et sisemine filtrisüsteem ei ole ummistunud. Veenduge, et tühjendusvoolik ei ole muljutud ega vää‐ natud. Sulgege veekraan ja pöörduge hoolduskeskusse. .
EESTI 65 12.1 Pesu- ja kuivatustulemused ei ole rahuldavad Probleem Võimalik põhjus ja lahendus Kehvad pesutulemused. • • • Kehvad kuivatustulemused. • • • • • Valged jooned ja plekid või si‐ nakas kiht klaasidel ja nõudel. Plekid ja kuivanud veetilkade jäljed nõudel ja klaasidel. Nõud on märjad. • • • • • • • • • Vt "Igapäevane kasutamine", "Vihjeid ja näpunäi‐ teid" ja infolehte korvide täitmise kohta. Kasutage intensiivsemaid pesuprogramme. Puhastage pihustikonsool ja filter.
www.aeg.com Probleem Võimalik põhjus ja lahendus Programmi lõpus on pesuaine‐ • jaoturis pesuainejäägid. • • Pesutablett on jäänud jaoturisse kinni ja pole seetõttu veega täielikult ära uhutud. Vesi ei suuda jaoturis olevat pesuainet välja uhtuda. Vaadake, ega pihustikonsool pole blokeeritud või um‐ mistunud. Kontrollige, ega korvides olevad esemed ei takista pe‐ suainejaoturi kaane avanemist. Seadmes on lõhnad. • Vt "Sisemuse puhastamine". Katlakivijäägid nõudel, sise‐ musel ja ukse siseküljel.
EESTI Võimsustarve väljalülitatud seisundis (W) 0.50 Võimsustarve ooteseisundis (W) 5.0 Veetarbimine liitrites aastas, võttes aluseks 280 tavalist pesemistsü‐ klit. Seadme tegelik veetarbimine oleneb selle kasutusviisist.
156910624-A-442018 www.aeg.