FSB52620Z DE IT ES USER MANUAL Benutzerinformation Geschirrspüler Istruzioni per l’uso Lavastoviglie Manual de instrucciones Lavavajillas 2 26 49
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................5 3. GERÄTEBESCHREIBUNG........................................................................................... 6 4. BEDIENFELD................................................................................................................7 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com Bauernhöfe, Personalküchenbereiche in Geschäften, Büros und anderen Arbeitsumfeldern. – Für Gäste in Hotels, Motels, Pensionen und anderen wohnungsähnlichen Räumlichkeiten. Nehmen Sie keine technischen Änderungen am Gerät vor. Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt.
DEUTSCH 5 2. SICHERHEITSANWEISUNGEN 2.1 Montage WARNUNG! Die Montage des Geräts darf nur von einer qualifizierten Fachkraft durchgeführt werden. • Entfernen Sie das gesamte Verpackungsmaterial. • Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. • Halten Sie sich an die mitgelieferte Montageanleitung. • Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk.
www.aeg.com solche nicht in die Nähe oder auf das Gerät. des Wasserzulaufschlauchs an den autorisierten Kundendienst. 2.4 Gebrauch 2.5 Service • Setzen oder stellen Sie sich niemals auf die geöffnete Gerätetür. • Geschirrspüler-Reinigungsmittel sind gefährlich. Beachten Sie die Sicherheitsanweisungen auf der Reinigungsmittelverpackung. • Trinken Sie nicht das Wasser aus dem Gerät und verwenden Sie es nicht zum Spielen. • Nehmen Sie kein Geschirr aus dem Gerät, bevor das Programm beendet ist.
DEUTSCH 9 Besteckkorb 10 Unterkorb 11 Oberkorb 3.1 Beam-on-Floor Nach dem Abschalten des Gerätes erlischt der Beamon-Floor. Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Boden projiziert wird. Wird AirDry während der Trockenphase eingeschaltet, ist die Projektion auf dem Boden möglicherweise nicht vollständig sichtbar. Sie können dann auf dem Bedienfeld sehen, ob das Programm beendet wurde.
www.aeg.
DEUTSCH Wasserverbrauch (l) Energieverbrauch (kWh) Dauer (min.) P2 7 - 12 0.7 - 1.5 45 - 160 P3 13 - 15 1.4 - 1.6 140 - 160 P4 9 0.8 30 P5 13 - 14 0.9 - 1.1 70 - 85 Programm1) 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Informationen für Prüfinstitute Wenn Sie Informationen zur Durchführung von Leistungsprüfungen (z.B.
www.aeg.com , und blinken und das Display nichts anzeigt. 6.2 Wasserenthärter Der Wasserenthärter entfernt Mineralien aus dem Spülwasser, die sich nachteilig auf die Spülergebnisse und das Gerät auswirken könnten. Je höher der Mineralgehalt ist, um so härter ist Ihr Wasser. Die Wasserhärte wird in gleichwertigen Einheiten gemessen. Der Enthärter muss entsprechend der Wasserhärte Ihres Gebietes eingestellt werden. Ihr lokales Wasserwerk kann Sie über die Wasserhärte in Ihrem Gebiet informieren.
DEUTSCH 6.3 Klarspülmittelnachfüllanzeige Das Klarspülmittel ermöglicht das Trocknen des Geschirrs ohne Streifen und Flecken. Das Klarspülmittel wird automatisch während der heißen Spülphase abgegeben. Ist das Klarspülmittelfach leer, wird die Klarspülmittelnachfüllanzeige eingeschaltet und weist darauf hin, dass Klarspülmittel nachgefüllt werden sollte.
www.aeg.com Während der Trockenphase wird die Tür automatisch geöffnet und bleibt einen Spaltbreit offen. VORSICHT! Versuchen Sie nicht, die Gerätetür innerhalb der ersten 2 Minuten nach der automatischen Öffnung zu schließen. Andernfalls kann das Gerät beschädigt werden. AirDry wird bei allen Programmen mit (falls vorhanden) Ausnahme von automatisch eingeschaltet. Zur Verbesserung der Trocknungsleistung beachten Sie die XtraDry-Option oder schalten Sie AirDry ein.
DEUTSCH Die Option XtraDry bleibt permanent für alle Programme außer für eingeschaltet und muss nicht mit jedem Programm erneut ausgewählt werden. In anderen Programmen bleibt die Einstellung von XtraDry gespeichert und wird automatisch verwendet. Sie können diese Konfiguration jederzeit ändern. Jedes Mal, wenn eingeschaltet wird, wird die Option XtraDry ausgeschaltet und muss manuell ausgewählt werden. Durch das Einschalten der Option XtraDry wird TimeSaver ausgeschaltet und umgekehrt.
www.aeg.com 8.2 Füllen des KlarspülmittelDosierers A D 4. Schütteln Sie den Trichter leicht am Griff, damit auch die verbleibenden Körner in den Behälter gelangen. 5. Entfernen Sie das Salz, das sich um die Öffnung des Salzbehälters herum angesammelt hat. B C B A M AX + 6. Drehen Sie den Deckel des Salzbehälters im Uhrzeigersinn, um den Salzbehälter zu schließen. VORSICHT! Beim Befüllen des Salzbehälters können Wasser und Salz austreten.
DEUTSCH 15 9. TÄGLICHER GEBRAUCH 1. Öffnen Sie den Wasserhahn. 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. • Füllen Sie den Salzbehälter auf, wenn die Kontrolllampe Salz leuchtet. • Leuchtet die Kontrolllampe Klarspülmittel, füllen Sie den Klarspülmittel-Dosierer. 3. Beladen Sie die Körbe. 4. Füllen Sie Reinigungsmittel ein. 5. Stellen Sie je nach Beladung und Verschmutzungsgrad das passende Programm ein. 9.
www.aeg.com Die Kontrolllampe der Zeitvorwahl leuchtet auf. 3. Schließen Sie die Gerätetür, um den Countdown zu starten. Während des Countdowns kann die Zeitvorwahl weiter verlängert werden, es ist jedoch nicht möglich, die ausgewählten Programme und Optionen zu ändern. Nach Ablauf der Zeitvorwahl wird das Programm gestartet. Öffnen der Tür während eines laufenden Programms Wenn Sie die Tür während eines laufenden Programms öffnen, stoppt das Gerät.
DEUTSCH • Achten Sie darauf, dass das Geschirr in den Körben sich weder berührt noch von anderem Geschirr verdeckt wird. Nur so erreicht das Spülwasser das ganze Geschirr. • Sie können Geschirrspülreiniger, Klarspülmittel und Salz separat oder Kombi-Reinigungstabletten (z.B. „Allin-1“) verwenden. Beachten Sie die auf der Verpackung angegebenen Hinweise. • Wählen Sie ein Programm, das für die Beladung und den Verschmutzungsgrad geeignet ist. bietet den effizientesten Wasser- und Energieverbrauch. 10.
www.aeg.com • Vergewissern Sie sich, dass sich der Sprüharm ungehindert bewegen kann, bevor Sie ein Programm starten. 10.5 Vor dem Starten eines Programms Stellen Sie vor dem Start des Programms sicher, dass: • Die Siebe sauber und ordnungsgemäß eingesetzt sind. • Der Deckel des Salzbehälters fest geschlossen ist. • Die Sprüharme nicht verstopft sind. • Geschirrspülsalz und Klarspülmittel vorhanden sind (außer Sie verwenden Multi-Reinigungstabletten).
DEUTSCH 19 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet. 4. Reinigen Sie die Filter. VORSICHT! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 5.
www.aeg.com 11.4 Reinigung des Geräteinnenraums • Reinigen Sie das Gerät und die Gummidichtung der Tür sorgfältig mit einem weichen, feuchten Tuch. • Wenn Sie regelmäßig Kurzprogramme verwenden, können diese zu Fett- und Kalkablagerungen im Gerät führen. Um dieses zu vermeiden, wird empfohlen, mindestens zweimal im Monat Programme mit langer Laufzeit zu verwenden.
DEUTSCH 21 Störung und Alarmcode Mögliche Ursache und Abhilfe Es läuft kein Wasser in das Gerät. • Stellen Sie sicher, dass der Wasserzulaufhahn geöffnet ist. • Vergewissern Sie sich, dass der Wasserdruck der Wasserversorgung nicht zu niedrig ist. Diese Informationen erhalten Sie von Ihrem lokalen Wasserversorger. • Stellen Sie sicher, dass der Wasserzulaufhahn nicht verstopft ist. • Vergewissern Sie sich, dass das Sieb im Zulaufschlauch nicht verstopft ist.
www.aeg.com Störung und Alarmcode Mögliche Ursache und Abhilfe Klappernde/schlagende Ge- • Das Geschirr ist nicht richtig in den Körben eingeordnet. räusche aus dem GeräteinSiehe Broschüre zum Beladen der Körbe. neren. • Achten Sie darauf, dass sich die Sprüharme frei drehen können. Das Gerät löst die Sicherung • Die abgesicherte Stromstärke reicht nicht für den gleichaus. zeitigen Betrieb aller eingeschalteten Geräte. Überprüfen Sie, für welche Stromstärke die Steckdose bzw.
DEUTSCH 23 Störung Mögliche Ursache und Abhilfe Wasserflecken und andere Flecken auf Gläsern und Geschirr. • Die zugegebene Klarspülmittelmenge ist zu niedrig. Stellen Sie eine höhere Klarspülmittelmenge ein. • Die Ursache kann in der Qualität des Klarspülmittels liegen. Das Geschirr ist nass. • Schalten Sie die Option XtraDry ein, und stellen Sie AirDry ein, um die beste Trocknungsleistung zu erzielen. • Das Programm enthält keine Trocknungsphase oder eine Trocknungsphase mit niedriger Temperatur.
www.aeg.com Störung Mögliche Ursache und Abhilfe Kalkablagerungen auf dem Geschirr, im Innenraum und auf der Türinnenseite. • Es befindet sich zu wenig Salz im Behälter, prüfen Sie die Nachfüllanzeige. • Der Deckel des Salzbehälters ist locker. • Ihr Leitungswasser ist hart. Siehe „Wasserenthärter“. • Verwenden Sie stets Salz, auch wenn Sie Multi-Reinigungstabletten nutzen und stellen Sie die Regenerierung des Wasserenthärters ein. Siehe „Wasserenthärter“.
DEUTSCH Wasserverbrauch in Liter/Jahr, auf der Grundlage von 280 Standardreinigungszyklen. Der tatsächliche Wasserverbrauch hängt von der Art der Nutzung des Geräts ab. 2775 Trocknungseffizienzklasse auf einer Skala von G (geringste Effizienz) bis A (höchste Effizienz).
www.aeg.com INDICE 1. INFORMAZIONI DI SICUREZZA...............................................................................27 2. ISTRUZIONI DI SICUREZZA...................................................................................... 29 3. DESCRIZIONE DEL PRODOTTO............................................................................. 30 4. PANNELLO COMANDI.............................................................................................31 5. PROGRAMMI...........................
ITALIANO 1. 27 INFORMAZIONI DI SICUREZZA Leggere attentamente le istruzioni fornite prima di installare e utilizzare l'apparecchiatura. I produttori non sono responsabili di eventuali lesioni o danni derivanti da un'installazione o un uso scorretti. Conservare sempre le istruzioni in un luogo sicuro e accessibile per poterle consultare in futuro. 1.
www.aeg.com clienti di hotel, motel, bed and breakfast e altri ambienti residenziali. Non modificare le specifiche tecniche dell'apparecchiatura. La pressione di esercizio dell'acqua (minima e massima) deve essere compresa tra 0.5 (0.05) / 8 (0.8) bar (MPa) Rispettare il numero massimo di 13 coperti. Se il cavo di alimentazione è danneggiato, deve essere sostituito dal produttore, dal Centro di Assistenza Autorizzato o da una persona qualificata per evitare situazioni di pericolo.
ITALIANO 29 2. ISTRUZIONI DI SICUREZZA 2.1 Installazione AVVERTENZA! L’installazione dell'apparecchiatura deve essere eseguita da personale qualificato. • Rimuovere tutti i materiali di imballaggio. • Non installare o utilizzare l'apparecchiatura se è danneggiata. • Attenersi alle istruzioni fornite insieme all'apparecchiatura. • Prestare sempre attenzione in fase di spostamento dell'apparecchiatura, dato che è pesante. Usare sempre i guanti di sicurezza e le calzature adeguate.
www.aeg.com • Utilizzare esclusivamente ricambi originali. • I detersivi per la lavastoviglie sono pericolosi. Osservare le istruzioni di sicurezza riportate sulla confezione del detersivo. • Non bere o giocare con l’acqua all’interno dell’apparecchiatura. • Non rimuovere i piatti dall'apparecchiatura fino al completamento del programma. Potrebbe rimanere del detergente sui piatti. • L'apparecchiatura può rilasciare vapore caldo se si apre la porta durante lo svolgimento del programma.
ITALIANO 7 Contenitore del brillantante 8 Erogatore del detersivo 9 Cestello per le posate 10 Cestello inferiore 11 Cestello superiore 3.1 Beam-on-Floor Quando viene attivato AirDry durante la fase di asciugatura, la proiezione sul pavimento potrebbe non essere completamente visibile. Per vedere se il ciclo si è concluso, controllare il pannello di controllo. Il Beam-on-Floor è un fascio di luce mostrato sul pavimento al di sotto della porta dell'apparecchiatura.
www.aeg.com 5. PROGRAMMI La numerazione dei programmi nella tabella (P1, P2, ecc.) riflette la loro sequenza sul pannello di controllo. L'ordine dei programmi nella tabella potrebbe non riflettere la loro sequenza sul pannello di controllo.
ITALIANO Programma 1) Acqua (l) Energia elettrica (kWh) Durata (min.) P3 13 - 15 1.4 - 1.6 140 - 160 P4 9 0.8 30 P5 13 - 14 0.9 - 1.1 70 - 85 33 1) I valori possono variare a seconda della pressione e della temperatura dell'acqua, delle variazioni dell'alimentazione elettrica, delle opzioni selezionate e della quantità di stoviglie. 5.
www.aeg.com 6.2 Decalcificatore dell’acqua Il decalcificatore rimuove dall'acqua i minerali che avrebbero effetti negativi sui risultati di lavaggio e sull'apparecchiatura. La durezza dell'acqua dipende dal contenuto di questi minerali. La durezza dell'acqua è misurata in scale equivalenti. Il decalcificatore dell'acqua deve essere regolato in base alla durezza dell’acqua locale. Per informazioni sulla durezza dell’acqua nella propria zona è possibile rivolgersi all’ente erogatore locale.
ITALIANO Quando la vaschetta del brillantante è vuota, la spia corrispondente è attiva per indicare di aggiungere altro brillantante. Se i risultati di lavaggio sono soddisfacenti quando vengono usate solo pastiglie multifunzione, sarà possibile disattivare la notifica per il rifornimento del brillantante. Per prestazioni di asciugatura eccellenti, consigliamo tuttavia di usare sempre il brillantante.
www.aeg.com Per migliorare le prestazioni di asciugatura, fare riferimento all'opzione XtraDry o attivare nuovamente AirDry. ATTENZIONE! Qualora i bambini abbiano accesso all'apparecchiatura, consigliamo di disattivare AirDry in quanto l'apertura della porta potrebbe costituire un pericolo. Come disattivare l'opzione AirDry 1. Premere • Le spie . , e si spengono. • La spia lampeggia ancora. • Il display mostra l'impostazione attuale: = AirDry attivato. per cambiare 2.
ITALIANO 7.2 TimeSaver 37 programma. I risultati di asciugatura possono ridursi. L'opzione aumenta la pressione e la temperatura dell'acqua. Le fasi di lavaggio e di asciugatura sono più brevi. Come attivare TimeSaver La durata complessiva del programma si riduce di circa il 50%. Premere . La spia relativa è accesa. Il display indica la durata aggiornata del programma. I risultati di lavaggio sono gli stessi che si ottengono con la normale durata del 8. PRIMA DI UTILIZZARE L'ELETTRODOMESTICO 1.
www.aeg.com ATTENZIONE! Acqua e sale potrebbero fuoriuscire dal contenitore del sale durante il riempimento. Dopo aver riempito il contenitore del sale, avviare immediatamente un programma volto ad evitare la corrosione. 8.2 Come riempire il contenitore del brillantante A D B ATTENZIONE! Utilizzare solo prodotti brillantanti specifici per lavastoviglie. 1. Premere il tasto di sgancio (D) per aprire il coperchio (C). 2.
ITALIANO 9.1 Utilizzo del detersivo 30 20 3. Premere ripetutamente o finché il display non mostra il numero del programma selezionato. Il display mostrerà il numero del programma per circa 3 secondi, e poi indica la durata del programma. 4. Impostare le opzioni disponibili. 5. Chiudere la porta dell'apparecchiatura per avviare il programma. C 30 B Avvio di un programma 1. Tenere la porta dell'apparecchiatura socchiusa. 2. Premere il tasto On/Off per accendere l’apparecchiatura.
www.aeg.com Se la porta rimane aperta per più di 30 secondi durante la fase di asciugatura, il programma in corso termina. Ciò non avviene se la porta viene aperta dalla funzione AirDry. Non provare a chiudere la porta dell'apparecchiatura entro 2 minuti dopo che AirDry la apre automaticamente, dato che ciò potrebbe causare danni all'apparecchiatura. Qualora successivamente la porta venga chiusa per altri 3 minuti, si conclude la modalità in funzione.
ITALIANO evitare residui di detersivo sulle stoviglie, consigliamo di utilizzare il detersivo in pastiglie con i programmi lunghi. • Non usare una dose di detersivo superiore alla quantità raccomandata. Osservare le istruzioni riportate sulla confezione del detersivo. 10.3 Cosa fare se non si desidera utilizzare più il detersivo in pastiglie multifunzione Prima di iniziare ad usare separatamente detersivo, sale e brillantante attenersi alla procedura seguente: 1.
www.aeg.com 11. PULIZIA E CURA AVVERTENZA! Prima di eseguire qualunque intervento di manutenzione, spegnere l'apparecchiatura ed estrarre la spina dalla presa. Filtri sporchi e mulinelli ostruiti riducono i risultati di lavaggio. Eseguire controlli periodici e pulirli, se necessario. 3. Rimuovere il filtro piatto (A). 4. Lavare i filtri. 11.1 Pulizia dei filtri Il sistema del filtro si compone di 3 parti. C B A 5.
ITALIANO 43 • Utilizzare solo detergenti neutri. • Non usare prodotti abrasivi, spugnette abrasive o solventi. 11.4 Pulizia interna ATTENZIONE! Un’errata posizione dei filtri può comportare scadenti risultati di lavaggio e danni all’apparecchiatura. 11.2 Pulizia dei mulinelli Non rimuovere i mulinelli. Se i fori dei mulinelli sono ostruiti da residui di sporco, liberarli servendosi di un oggetto a punta fine.
www.aeg.com Problema e codice allarme Possibile causa e soluzione Non è possibile accendere l'apparecchiatura. • Verificare che la spina sia collegata alla presa elettrica. • Assicurarsi che il fusibile all'interno del quadro elettrico non sia danneggiato. Il programma non si avvia. • Controllare che l’oblò dell’apparecchiatura sia chiuso. • Se è stato impostato il ritardo, annullare l'impostazione o attendere il termine del conto alla rovescia.
ITALIANO 45 Problema e codice allarme Possibile causa e soluzione La porta dell'apparecchiatura si chiude con difficoltà. • L'apparecchiatura non è correttamente livellata. Allentare o stringere i piedini regolabili (ove previsti). • Alcune parti di pentole e stoviglie sporgono dai cestelli. Tintinnio/colpi dall'interno dell'apparecchiatura. • Le pentole e le stoviglie non sono state sistemate adeguatamente nei cestelli. Fare riferimento al libretto contenente le indicazioni per caricare il cestello.
www.aeg.com Problema Possibile causa e soluzione Su bicchieri e stoviglie riman- • La quantità di brillantante erogata è eccessiva. Regogono delle striature biancastre lare il livello del brillantante su una posizione inferiore. o striature bluastre. • È stata utilizzata una dose eccessiva di detersivo. Macchie e tracce di gocce d'acqua su bicchieri e stoviglie. • La quantità di brillantante erogata non è sufficiente. Regolare il livello del brillantante su una posizione superiore.
ITALIANO Problema 47 Possibile causa e soluzione Il calcare può depositarsi su • Il livello di sale è basso, controllare l'indicatore di pentole e stoviglie, nella vasca riempimento. o all'interno della porta. • Il tappo del contenitore del sale è lento. • L'acqua di rubinetto è dura. Fare riferimento a "Decalcificatore dell'acqua". • Anche le pastiglie multi-funzione usano il sale e impostano la rigenerazione dell'ammorbidente dell'acqua. Fare riferimento a "Decalcificatore dell'acqua".
www.aeg.com Consumo di acqua in litri/anno, basato su 280 cicli di lavaggio standard.
ESPAÑOL 49 CONTENIDO 1. INFORMACIÓN SOBRE SEGURIDAD..................................................................... 50 2. INSTRUCCIONES DE SEGURIDAD..........................................................................51 3. DESCRIPCIÓN DEL PRODUCTO............................................................................. 53 4. PANEL DE CONTROL............................................................................................... 54 5. PROGRAMAS..........................................
1. www.aeg.com INFORMACIÓN SOBRE SEGURIDAD Antes de instalar y utilizar el aparato, lea atentamente las instrucciones facilitadas. El fabricante no se hace responsable de lesiones o daños producidos como resultado de una instalación o un uso incorrectos: Conserve siempre estas instrucciones en lugar seguro y accesible para futuras consultas. 1.
ESPAÑOL 51 por clientes en hoteles, moteles, pensiones y otros entornos de tipo residencial. No cambie las especificaciones de este aparato. La presión de agua de funcionamiento (mínima y máxima) debe estar entre 0.5 (0.05) / 8 (0.8) bares (MPa) Respete el máximo número de ajustes de lugar de 13 . Si el cable eléctrico sufre algún daño, el fabricante, su servicio técnico autorizado o un profesional cualificado tendrán que cambiarlo para evitar riesgos.
www.aeg.com • El aparato debe conectarse a tierra. • Asegúrese de que los parámetros de la placa de características son compatibles con los valores eléctricos del suministro eléctrico. • Utilice siempre una toma con aislamiento de conexión a tierra correctamente instalada. • No utilice adaptadores de enchufes múltiples ni cables prolongadores. • Asegúrese de no provocar daños en el enchufe ni en el cable de red.
ESPAÑOL • Desconecte el aparato de la red. • Corte el cable de conexión a la red y deséchelo. • Retire el pestillo de la puerta para evitar que los niños y las mascotas queden encerrados en el aparato. 3. DESCRIPCIÓN DEL PRODUCTO 1 2 11 10 1 2 3 4 5 6 9 8 7 Brazo aspersor intermedio Brazo aspersor inferior Filtros Placa de características Depósito de sal Salida de aire 3.1 Beam-on-Floor Beam-on-Floor es una luz que aparece en el suelo bajo la puerta del aparato.
www.aeg.com 4. PANEL DE CONTROL 1 1 2 3 4 5 2 3 Botón de encendido/apagado Pantalla Tecla Delay Tecla de programa (ascendente) Tecla de programa (descendente) 4 6 7 8 9 5 6 7 8 9 Tecla TimeSaver Tecla XtraDry Tecla RESET Indicadores 4.1 Indicadores Indicador Descripción Indicador de abrillantador. Siempre está apagado mientras el programa está en funcionamiento. Indicador de sal. Siempre está apagado mientras el programa está en funcionamiento. 5.
ESPAÑOL Programa Grado de suciedad Fases del programa Tipo de carga P4 • Suciedad recien- • Lavado a 60 °C o 65 °C • XtraDry te • Aclarados • Vajilla y cubiertos 3) P5 • Suciedad normal • Lavado a 45 ºC o ligera • Aclarados • Vajilla y cristale- • Secado ría finas 55 Opciones • XtraDry 1) Este programa ofrece el uso más eficaz del agua y consumo de energía para vajillas y cubiertos con suciedad normal. Este es el programa estándar para institutos de pruebas.
www.aeg.com 6. AJUSTES 6.1 Modo de selección de programa y modo de usuario Cómo acceder al modo de usuario Cuando el aparato está en el modo de selección de programa, es posible ajustar un programa y pasar al modo de usuario. Asegúrese de que el aparato se encuentra en modo de selección de programa. Ajustes disponibles en el modo de usuario: • El nivel del descalcificador de agua según la dureza de la misma. • La activación o desactivación de la señal acústica de fin de programa.
ESPAÑOL 57 Grados alemanes (°dH) Grados franceses (°fH) mmol/l Grados Clarke Nivel del descalcificador del agua 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Ajuste de fábrica. 2) No utilice sal en este nivel.
www.aeg.com 6.4 Señales acústicas Las señales acústicas suenan cuando se produce un fallo del aparato. No es posible desactivar estas señales acústicas. Al finalizar el programa también suena una señal acústica. Por defecto, esta señal acústica está desactivada pero es posible activarla. Cómo activar la señal acústica que indica el final del programa Asegúrese de que el aparato se encuentra en modo de usuario. 1. Pulse . • Los indicadores están apagados. , y sigue • El indicador parpadeando.
ESPAÑOL 59 7. OPCIONES Cada vez que inicie un programa debe activar las opciones que desee. No es posible activar ni desactivar opciones con el programa en marcha. No todas las opciones son compatibles entre sí. Si selecciona opciones no compatibles, el aparato desactiva automáticamente una o más de ellas. Solo permanecen encendidos los indicadores de las opciones aún activas.
www.aeg.com Después de iniciar un programa, el aparato puede tardar hasta 5 minutos en recargar la resina del descalcificador. Parece que el aparato no funciona. La fase de lavado empieza solo después de que termine este proceso. El proceso se repite periódicamente. 8.1 El depósito de sal PRECAUCIÓN! Utilice solo sal gruesa diseñada para lavavajillas. La sal fina aumenta el riesgo de corrosión.
ESPAÑOL absorbente para evitar que se forme demasiada espuma. 4. Cierre la tapa. Asegúrese de que la tecla de apertura se encaja en su sitio. 61 Puede girar el selector de la cantidad (B) entre la posición 1 (menor cantidad) y la posición 4 o 6 (mayor cantidad). 9. USO DIARIO 1. Abra la llave de paso. 2. Pulse la tecla de encendido/apagado para encender el aparato. Asegúrese de que el aparato se encuentra en modo de selección de programa. • Si el indicador de sal está encendido, llene el depósito.
www.aeg.com Inicio de un programa con inicio diferido 1. Ajuste un programa. 2. Pulse repetidamente hasta que la pantalla muestre el tiempo de retardo que desee ajustar (entre 1 y 24 horas). Se enciende el indicador de inicio diferido. 3. Cierre la puerta del aparato para iniciar la cuenta atrás. Mientras se realiza la cuenta atrás se puede aumentar el tiempo de retardo, pero no es posible cambiar la selección del programa. El programa se pone en marcha cuando termina la cuenta atrás.
ESPAÑOL • No enjuague los platos a mano. Cuando sea necesario, seleccione un programa con fase de prelavado. • Aproveche siempre todo el espacio de los cestos. • Asegúrese de que los objetos de los cestos no se tocan entre sí ni se cubren unos a otros. Solo entonces el agua puede llegar a todos los platos y lavarlos completamente. • Puede utilizar detergente para lavavajillas, abrillantador y sal por separado o pastillas múltiples (p. ej. "Todo en 1"). Siga las instrucciones que aparecen en el paquete.
www.aeg.com • Hay abrillantador y sal suficientes (a menos que utilice pastillas múltiples). • La disposición de los objetos en los cestos es correcta. • El programa es adecuado para el tipo de carga y el grado de suciedad. • Se utiliza la cantidad correcta de detergente. artículos calientes son sensibles a los golpes. 2. Vacíe primero el cesto inferior y a continuación el superior. Después de terminar el programa, todavía puede quedar agua en las superficies interiores del aparato. 10.
ESPAÑOL 65 PRECAUCIÓN! Una posición incorrecta de los filtros puede dañar el aparato y provocar resultados de lavado no satisfactorios. 11.2 Limpieza de los brazos aspersores No retire los brazos aspersores. Si los orificios de los brazos aspersores se taponan, retire la suciedad restante con un objeto afilado. 5. Asegúrese de que no haya restos de comida ni suciedad alrededor del borde del sumidero. 6. Vuelva a colocar el filtro plano (A). Asegúrese de que esté bien colocado bajo las 2 guías. 11.
www.aeg.com 12. SOLUCIÓN DE PROBLEMAS Si el aparato no se pone en marcha o se detiene durante el funcionamiento, compruebe si puede resolver el problema con ayuda de la información de la tabla antes de ponerse en contacto con el servicio técnico. ADVERTENCIA! Las reparaciones incorrectas pueden acarrar riesgos graves para la seguridad del usuario. Todas las reparaciones debe llevarlas a cabo personal cualificado. Algunos fallos de funcionamiento se indican en la pantalla con un código de alarma.
ESPAÑOL 67 Problema y código de alar- Causa y soluciones posibles ma El aparato se detiene y se pone en marcha más veces durante el funcionamiento. • Esto es correcto. Proporciona resultados de limpieza óptimos y ahorra energía. El programa dura demasiado. • Seleccione la opción TimeSaver para acortar la duración del programa. • Si se ha ajustado la opción de inicio diferido, cancele el retardo o espere hasta el final de la cuenta atrás.
www.aeg.com 12.1 Los resultados del lavado y el secado no son satisfactorios Problema Causa y soluciones posibles Mal resultado de lavado. • Consulte "Uso diario", "Consejos" y el folleto sobre cómo cargar el cesto. • Utilice programas de lavado más intensos. • Limpie las boquillas del brazo aspersor y el filtro. Consulte "Mantenimiento y limpieza". Malos resultados de secado. • Se ha dejado la vajilla demasiado tiempo dentro del aparato cerrado.
ESPAÑOL 69 Problema Causa y soluciones posibles Quedan restos de detergente en el dosificador al final del programa. • La pastilla de detergente se ha quedado pegada en el dosificador y no se ha disuelto totalmente en el agua. • El agua no puede disolver el detergente que hay en el dosificador. Compruebe que el brazo aspersor superior no esté bloqueado o atascado. • Asegúrese de que los objetos de los cestos no impiden que se abra la tapa del dosificador de detergente.
www.aeg.com Consumo de energía en kWh al año, basado en 280 ciclos de lavado normal, utilizando agua fría y el consumo de los modos de bajo consumo. El consumo de energía real depende de las condiciones de utilización del aparato. 262 Consumo de energía del ciclo de lavado normal (kWh) 0.921 Consumo de electricidad en el modo apagado (W) 0.50 Consumo de electricidad en el modo sin apagar (W) 5.0 Consumo de agua en litros al año, basado en 280 ciclos de lavado 2775 normal.
ESPAÑOL su centro de reciclaje local o póngase en contacto con su oficina municipal.
156911153-A-442018 www.aeg.