FSE62600P DE HU USER MANUAL Benutzerinformation Geschirrspüler Használati útmutató Mosogatógép 2 27
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................4 3. GERÄTEBESCHREIBUNG........................................................................................... 6 4. BEDIENFELD................................................................................................................7 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com • • • • • • • • • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt. Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, seinem autorisierten Kundenservice oder einer gleichermaßen qualifizierten Person ausgetauscht werden, um Gefahrenquellen zu vermeiden.
DEUTSCH • • • • • • • Typenschild den Daten Ihrer Stromversorgung entsprechen. Wenden Sie sich anderenfalls an eine Elektrofachkraft. Schließen Sie das Gerät unbedingt an eine sachgemäß installierte Schutzkontaktsteckdose an. Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen.
www.aeg.com Modell: Produkt-Nummer (PNC): Seriennummer: • Trennen Sie das Gerät von der Stromversorgung. • Schneiden Sie das Netzkabel ab, und entsorgen Sie es. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in dem Gerät einschließen. 2.6 Entsorgung WARNUNG! Verletzungs- und Erstickungsgefahr. 3. GERÄTEBESCHREIBUNG 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Oberster Sprüharm Oberer Sprüharm Unterer Sprüharm Filter Typenschild Salzbehälter Lüftungsschlitze 3.
DEUTSCH Wird AirDry während der Trockenphase eingeschaltet, ist die Projektion auf dem Boden möglicherweise nicht vollständig sichtbar. Sie können dann auf dem Bedienfeld sehen, ob das Programm beendet wurde. 4. BEDIENFELD 1 1 2 3 4 5 2 Taste „Ein/Aus“ Display Taste Delay Taste Program Taste Sanitize 3 6 7 8 9 4 5 6 7 8 9 Taste TimeSaver Taste XtraDry Taste Reset Kontrolllampen 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe Programmende. Kontrolllampe Klarspülmittel.
www.aeg.
DEUTSCH 9 5.1 Verbrauchswerte Wasser (l) Energieverbrauch (kWh) Dauer (Min.) P1 10.5 0.920 233 P2 7 - 14 0.6 - 1.6 40 - 154 P3 12.5 - 14.5 1.4 - 1.7 160 - 170 P5 12 - 14 0.7 - 0.9 84 - 94 P4 10 0.9 30 P6 9 - 10 1.1 - 1.3 219 - 229 Programm 1) 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.
www.aeg.com 6.2 Wasserenthärter Der Wasserenthärter entfernt Mineralien aus dem Spülwasser, die sich nachteilig auf die Spülergebnisse und das Gerät auswirken könnten. Je höher der Mineralgehalt ist, um so härter ist das Wasser. Die Wasserhärte wird in gleichwertigen Einheiten gemessen. Der Enthärter muss entsprechend der Wasserhärte in Ihrem Gebiet eingestellt werden. Ihr lokales Wasserwerk kann Sie über die Wasserhärte in Ihrem Gebiet informieren.
DEUTSCH 11 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. 6.4 Klarspülmittelnachfüllanzeige 6.3 Klarspülmittel-Dosierer Das Klarspülmittel ermöglicht das Trocknen des Geschirrs ohne Streifen und Flecken. Das Klarspülmittel ermöglicht das Trocknen des Geschirrs ohne Streifen und Flecken. Das Klarspülmittel wird automatisch während der heißen Spülphasen abgegeben. Sie können die Zugabemenge für Klarspülmittel zwischen Stufe 1 (Mindestmenge) und Stufe 6 (Höchstmenge) einstellen.
www.aeg.com 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. 6.5 Signaltöne Bei einer Störung des Geräts ertönen akustische Signale. Es ist nicht möglich, diese Signaltöne auszuschalten. Es ertönt auch ein Signalton, wenn das Programm beendet ist. Standardmäßig ist dieser Signalton ausgeschaltet, es ist jedoch möglich, ihn einzuschalten. So schalten Sie den Signalton für das Programmende ein Das Gerät muss sich im Programmwahlmodus befinden. 1.
DEUTSCH 3. Drücken Sie zur Änderung der Einstellung: = AirDry ausgeschaltet. 13 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. 7. OPTIONEN Sie müssen die gewünschten Optionen vor dem Programmstart einschalten. Es ist nicht möglich, Optionen während eines laufenden Programms einoder auszuschalten. Nicht alle Optionen lassen sich miteinander kombinieren.
www.aeg.com Einschalten von Sanitize Drücken Sie , die entsprechende Kontrolllampe leuchtet auf. Ist die Option nicht mit dem Programm kombinierbar, leuchtet die entsprechende Kontrolllampe nicht oder sie blinkt ein paar Sekunden schnell und erlischt dann. Das Display zeigt die aktualisierte Programmdauer an. 8. VOR DER ERSTEN INBETRIEBNAHME 1. Prüfen Sie, ob die Einstellung des Wasserenthärters der Wasserhärte in Ihrem Gebiet entspricht. Wenn nicht, stellen Sie die Wasserenthärterstufe ein. 2.
DEUTSCH 8.2 Füllen des KlarspülmittelDosierers A B Tuch auf, um zu große Schaumbildung zu vermeiden. 4. Schließen Sie den Deckel. Achten Sie darauf, dass der Deckel einrastet. Füllen Sie den Klarspülmittel-Dosierer auf, wenn die Füllstandsanzeige für den Klarspüler (A) durchsichtig wird. Wenn Sie MultiReinigungstabletten verwenden und die Trocknungsleistung zufriedenstellend ist, kann die Klarspülernachfüllanzeige ausgeschaltet werden.
www.aeg.com VORSICHT! Verwenden Sie nur Reinigungsmittel für Geschirrspüler. 1. Drücken Sie die Entriegelungstaste (A), um den Deckel (C) zu öffnen. 2. Füllen Sie das Reinigungsmittel ein oder legen Sie eine Reinigungstablette in den Behälter (B). 3. Wenn das Programm einen Vorspülgang hat, schütten Sie eine kleine Menge Reinigungsmittel auf die Innenseite der Gerätetür. 4. Schließen Sie den Deckel. Achten Sie darauf, dass der Deckel einrastet. 9.
DEUTSCH Abbrechen einer eingestellten Zeitvorwahl während des Countdowns Wenn Sie die eingestellte Zeitvorwahl abbrechen, müssen das Programm und die Optionen erneut eingestellt werden. Halten Sie Reset gedrückt, bis sich das Gerät im Programmwahlmodus befindet. 17 Bevor Sie ein neues Programm starten, stellen Sie sicher, dass der Reinigungsmittelbehälter gefüllt ist. Programmende Wenn das Programm beendet ist und Sie die Tür öffnen, schaltet sich das Gerät automatisch aus. Schließen Sie den Wasserhahn.
www.aeg.com 10.3 Was tun, wenn Sie keine Multi-Reinigungstabletten mehr verwenden möchten Vorgehensweise, um zur separaten Verwendung von Reinigungsmittel, Salz und Klarspülmittel zurückzukehren: 1. Stellen Sie die höchste Wasserenthärterstufe ein. 2. Stellen Sie sicher, dass der Salzbehälter und der KlarspülmittelDosierer gefüllt sind. 3. Starten Sie das kürzeste Programm mit einer Spülphase. Verwenden Sie kein Reinigungsmittel und beladen Sie die Körbe nicht. 4.
DEUTSCH 19 11.1 Reinigen der Filter Das Filtersystem besteht aus 3 Teilen. C B A 1. Drehen Sie den Filter (B) nach links und nehmen Sie ihn heraus. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 4. Reinigen Sie die Filter. 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein.
www.aeg.com VORSICHT! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 11.2 Reinigen des oberen Sprüharms Wir empfehlen den oberen Sprüharm regelmäßig zu reinigen, um zu verhindern, dass Verunreinigungen die Löcher verstopfen. Verstopfte Löcher können die Ursache für nicht zufriedenstellende Spülergebnisse sein. 1. Ziehen Sie den Oberkorb bis zum Anschlag heraus. 2.
DEUTSCH Programme mit langer Laufzeit zu verwenden. • Um die Leistungsfähigkeit des Geräts zu erhalten, wird (empfohlen mindestens einmal im Monat ein) 21 spezielles Reinigungsmittel für Geschirrspüler zu verwenden. Befolgen Sie sorgfältig die Anweisungen auf der Reinigungsmittelverpackung. 12. FEHLERSUCHE Das Gerät startet nicht oder bleibt während des Betriebs stehen.
www.aeg.com Störung und Alarmcode Mögliche Ursache und Abhilfe Das Gerät pumpt das Wasser nicht ab. • Stellen Sie sicher, dass der Siphon nicht verstopft ist. • Vergewissern Sie sich, dass der Filter im Ablaufschlauch nicht verstopft ist. • Vergewissern Sie sich, dass das interne Filtersystem nicht verstopft ist. • Vergewissern Sie sich, dass der Ablaufschlauch nicht geknickt oder zu stark gekrümmt ist. Im Display erscheint . Das Wasserauslauf-Schutzsystem ist eingeschaltet.
DEUTSCH Siehe „Vor der ersten Inbetriebnahme“, „Täglicher Gebrauch“ oder „Tipps und Hinweise“ bezüglich anderer möglicher Ursachen. 23 Problem erneut auf, wenden Sie sich an einen autorisierten Kundendienst. Wenden Sie sich an einen autorisierten Kundendienst, wenn Alarmcodes angezeigt werden, die nicht in der Tabelle angegeben sind. Schalten Sie nach der Überprüfung das Gerät aus und wieder ein. Tritt das 12.1 Die Spül- und Trocknungsergebnisse sind nicht zufriedenstellend.
www.aeg.com Störung Mögliche Ursache und Abhilfe Das Geschirr ist nass. • Schalten Sie die Option XtraDry ein, und stellen Sie AirDry ein, um die beste Trocknungsleistung zu erzielen. • Das Programm enthält keine Trocknungsphase oder eine Trocknungsphase mit niedriger Temperatur. • Der Klarspülmittel-Dosierer ist leer. • Die Ursache kann in der Qualität des Klarspülmittels liegen. • Die Ursache kann in der Qualität der Multi-Reinigungstabletten liegen.
DEUTSCH 25 Störung Mögliche Ursache und Abhilfe Kalkablagerungen auf dem Geschirr, im Innenraum und auf der Türinnenseite. • Es befindet sich zu wenig Salz im Behälter, prüfen Sie die Nachfüllanzeige. • Der Deckel des Salzbehälters ist locker. • Ihr Leitungswasser ist hart. Siehe „Wasserenthärter“. • Verwenden Sie stets Salz, auch wenn Sie Multi-Reinigungstabletten nutzen und stellen Sie die Regenerierung des Wasserenthärters ein. Siehe „Wasserenthärter“.
www.aeg.com 14. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte. Entsorgen Sie Geräte mit diesem Symbol nicht mit dem Hausmüll. Bringen Sie das Gerät zu Ihrer örtlichen Sammelstelle oder wenden Sie sich an Ihr Gemeindeamt.
MAGYAR 27 TARTALOM 1. BIZTONSÁGI INFORMÁCIÓK............................................................................ 28 2. BIZTONSÁGI UTASÍTÁSOK...............................................................................29 3. TERMÉKLEÍRÁS................................................................................................ 31 4. KEZELŐPANEL.................................................................................................. 32 5. PROGRAMOK.....................................
1. www.aeg.com BIZTONSÁGI INFORMÁCIÓK Az üzembe helyezés és használat előtt gondosan olvassa el a mellékelt útmutatót. A gyártó nem vállal felelősséget a helytelen beszerelés vagy használat miatt keletkezett sérülésekért és károkért. Tartsa biztonságos és elérhető helyen az útmutatót, hogy szükség esetén mindig a rendelkezésére álljon. 1.
MAGYAR • • • • • • • • 29 Soha ne lépje túl a megengedett legnagyobb töltetet 13 . Ha a hálózati kábel megsérül, azt a gyártónak vagy a márkaszerviznek vagy más hasonlóan képzett személynek kell kicserélnie, nehogy veszélyhelyzet álljon elő. Lefelé fordítva vagy vízszintes irányba tegye a késeket és a hegyes evőeszközöket az evőeszközkosárba. A beleütközés elkerülésének megelőzésére, ne hagyja nyitva felügyelet nélkül a készülék ajtaját.
www.aeg.com • • • • Amennyiben a készülék hálózati vezetékét ki kell cserélni, a cserét márkaszervizünknél végeztesse el. Csak az üzembe helyezés befejezése után csatlakoztassa a hálózati csatlakozódugót a hálózati csatlakozóaljzatba. Ügyeljen arra, hogy a hálózati dugasz üzembe helyezés után is könnyen elérhető legyen. A készülék csatlakozásának bontására, soha ne a hálózati kábelnél fogva húzza ki a csatlakozódugót. A kábelt mindig a csatlakozódugónál fogva húzza ki.
MAGYAR kedvenc állatok készülékben rekedését. 3. TERMÉKLEÍRÁS 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Legfelső szórókar Felső szórókar Alsó szórókar Szűrők Adattábla Sótartály Szellőzőnyílás 3.1 Beam-on-Floor A Beam-on-Floor fényjelzés a padlón, a készülék ajtaja alatt jelenik meg. • • • Amikor a program elkezdődik, piros fényjelzés jelenik meg, és a program időtartama alatt bekapcsolva marad. Amikor a program befejeződött, zöld fényjelzés jelenik meg.
www.aeg.com 4. KEZELŐPANEL 2 1 1 2 3 4 5 Be/ki gomb Kijelző Delay gomb Program gomb Sanitize gomb 3 6 7 8 9 4 5 6 7 8 9 TimeSaver gomb XtraDry gomb Reset gomb Visszajelzők 4.1 Visszajelzők Visszajelző Megnevezés Program vége visszajelző. Öblítőszer visszajelző. A program működése során ez a visszajelző soha‐ sem világít. Só visszajelző. A program működése során ez a visszajelző sohasem vi‐ lágít. 5.
MAGYAR Program Szennyezettség mértéke Töltet típusa P5 • • P4 • 3) • • P6 4) • Programfázisok 33 Kiegészítő funkciók Normál vagy • enyhe szennye‐ • ződés • Kényes cserépés üvegedények Mosogatás 45 °C Öblítések Szárítás • XtraDry Friss szennye‐ zettség Edények és evőeszközök • • Mosogatás 60 °C Öblítések • • Sanitize XtraDry Normál szeny‐ nyezettség Edények és evőeszközök • • • • Előmosogatás Mosogatás 50 °C Öblítések Szárítás • XtraDry 1) Ezzel a programmal a leghatékonyabb víz- é
www.aeg.com Program1) P6 Víz (l) Energiafogyasztás (kWh) Időtartam (perc) 9 - 10 1.1 - 1.3 219 - 229 1) A víz nyomása és hőmérséklete, a hálózati feszültség ingadozásai, a funkciók és az edények mennyi‐ sége módosíthatja az értékeket. 5.2 Tájékoztatás a bevizsgáló intézetek számára A bevizsgálás elvégzéséhez szükséges összes információ megszerzéséhez küldjön egy e-mailt a következő címre: info.test@dishwasher-production.com Jegyezze fel az adattáblán található termékszámot (PNC). 6.
MAGYAR 35 Vízkeménység Német fok (°dH) Francia fok (°fH) mmol/l Clarke fok Vízlágyító szintje 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
www.aeg.com 1. A felhasználói üzemmódba lépéshez egyszerre nyomja meg és tartsa lenyomva a és a gombokat, amíg a , , , és visszajelzők villogni nem kezdenek, és a kijelző üressé nem válik. 2. Nyomja meg az • • • , , A kialszanak. gombot. és visszajelzők visszajelző továbbra is A villog. A kijelző az aktuális beállítást mutatja: pl. = 4. szint. – Az öblítőszer szintje 0A és 6A között helyezkedhet el. – 0. szint = nincs öblítőszeradagolás. 3.
MAGYAR visszajelzők villogni nem kezdenek, és a kijelző üressé nem válik. 2. Nyomja meg az A , , kialszanak. • A visszajelző továbbra is villog. A kijelző az aktuális beállítást • és visszajelzők = Hangjelzés ki. mutatja: 3. A beállítás módosításához nyomja meg az VIGYÁZAT! Az automatikus ajtónyitást követő 2 percen belül ne próbálja meg az ajtót becsukni. Ez kárt tehet a készülékben. gombot. • gombot. = Hangjelzés be. 4. A beállítás megerősítéséhez nyomja meg a be/ki gombot. 6.
www.aeg.com 7.1 XtraDry Kapcsolja be ezt a kiegészítő funkciót, ha szeretné megnövelni a szárítási teljesítményt. Ezen kiegészítő funkció alkalmazásakor néhány program időtartama, a vízfogyasztás és az utolsó öblítés hőmérséklete módosulhat. Az XtraDry állandó kiegészítő funkció minden nem programnál, és nem kell beállítani minden ciklusnál. Az program elindításakor az XtraDry kiegészítő funkció inaktív, és mindig kézzel kell bekapcsolni.
MAGYAR ahhoz, hogy a vízlágyítóban lévő műgyantát regenerálja. Ekkor úgy tűnhet, hogy a készülék nem működik megfelelően. A mosási fázis csak akkor kezdődik meg, amikor a fenti művelet véget ér. Ez a műveletsor rendszeres időközönként ismétlődik. 8.1 Sótartály VIGYÁZAT! Csak mosogatógéphez készült, speciális sót használjon. 39 VIGYÁZAT! Víz és só juthat ki a töltés során a sótartályból. Miután feltöltötte a sótartályt, azonnal indítsa el a mosogatóprogramot a korrózió megelőzése érdekében. 8.
www.aeg.com Ha kombinált mosogatószertablettákat használ, és a szárítási eredmény megfelelő, az öblítőszer feltöltésére figyelmeztető visszajelzőt ki lehet kapcsolni. Javasoljuk, hogy mindig használjon öblítőszert a jobb szárítási eredmény érdekében akkor is, ha öblítőszert tartalmazó kombinált mosogatószertablettákat használ. 9. NAPI HASZNÁLAT 1. Nyissa ki a vízcsapot. 2. A készülék bekapcsolásához nyomja meg a be/ki gombot. Ügyeljen arra, hogy a készülék programválasztási üzemmódban legyen.
MAGYAR A program indítása Ha a szárítási fázis alatt 30 másodpercnél hosszabb időre kinyitja az ajtót, az éppen futó program kikapcsol. Ez nem történik meg, ha az ajtót az AirDry funkció nyitja ki. 1. Tartsa résnyire nyitva a készülék ajtaját. 2. A készülék bekapcsolásához nyomja meg a be/ki gombot. Győződjön meg arról, hogy a készülék programválasztás üzemmódban van. 3.
www.aeg.com • • • • • Az edényeket ne öblítse le kézzel előzetesen. Ha szükséges, használja az előmosogatási programot (ha van), vagy válasszon előmosogatási fázissal rendelkező mosogatóprogramot. Mindig használja ki a kosarak teljes területét. A készülékbe való bepakoláskor ügyeljen arra, hogy a mosogatókar fúvókáiból kilépő víz teljesen elérhesse és lemoshassa az edényeket. Ügyeljen arra, hogy az edények ne érjenek egymáshoz, illetve ne fedjék le egymást.
MAGYAR • A mosogatóprogram elindítása előtt győződjön meg arról, hogy a szórókarok szabadon mozoghatnak. 10.5 Egy program indítása előtt A következőket ellenőrizze: • • • • • A szűrők tiszták és megfelelően vannak elhelyezve. Szoros a sótartály kupakjának rögzítése. Nem tömődtek el a szórókarok. Van regeneráló só és öblítőszer (ha nem kombinált mosogatószertablettákat használ). Megfelelő az edények elhelyezése a kosarakban.
www.aeg.com 7. Szerelje vissza a szűrőket (B) és (C). 8. Tegye vissza a szűrőt (B) a lapos szűrőbe (A). Az óramutató járásával megegyező irányban forgassa, amíg nem rögzül. 2. Húzza ki a (C) szűrőt a (B) szűrőből. 3. Vegye ki a lapos szűrőt (A). 4. Vízzel tisztítsa meg a szűrőket. VIGYÁZAT! A szűrők helytelen pozíciója nem kielégítő mosogatási eredményt okoz, és a készüléket is károsítja. 11.
MAGYAR például fogvájóval távolítsa el a szennyeződést a furatokból. 45 11.3 Külső tisztítás • • • A készüléket puha, nedves ruhával tisztítsa. Csak semleges tisztítószert használjon. Ne használjon súrolószert, súrolószivacsot vagy oldószereket. 11.4 Belső tisztítás • • 4. A szórókar kosárhoz rögzítéséhez nyomja a szórókart felfelé, az alsó nyíl által jelzett irányba, és közben fordítsa el az óramutató járásával ellentétes irányba, míg a helyére nem rögzül.
www.aeg.com Meghibásodás és riasztási Lehetséges ok és megoldás kód Nem lehet bekapcsolni a ké‐ • szüléket. • Ügyeljen arra, hogy a villásdugó be legyen dugva a há‐ lózati aljzatba. Ellenőrizze, hogy nem oldott-e ki valamelyik biztosíték a biztosítékdobozban. A program nem indul el. Ellenőrizze, hogy a készülék ajtaja be van-e csukva. Ha késleltetett indítás van beállítva, törölje azt, vagy vár‐ ja meg a visszaszámlálás befejeződését. A készülék megkezdte a gyanta regenerálását a vízlá‐ gyítóban.
MAGYAR 47 Meghibásodás és riasztási Lehetséges ok és megoldás kód Nehéz becsukni a készülék ajtaját. • A készülék szintezése nem megfelelő. A vízszintbe állí‐ táshoz lazítsa vagy húzza meg az állítható lábakat (ha vannak). Az edények és evőeszközök egyes részei kiállnak a ko‐ sarakból. • Csörgő/kopogó zaj hallatszik • a készülék belsejéből. Az edények és evőeszközök elhelyezése nem megfelelő a kosarakban. Lásd a kosár megpakolására vonatkozó ismertetőt.
www.aeg.com Jelenség Lehetséges ok és megoldás A szárítás eredménye nem ki‐ elégítő. • • • • • Az elmosogatott tárgyakat túl hosszú ideig hagyta a zárt készülékben. Nincs a készülékben öblítőszer, vagy nem elegendő az adagolt öblítőszer mennyisége. Állítsa az öblítő‐ szer-adagolót magasabb fokozatra. Szükséges lehet a műanyag evőeszközök és edények törülközővel való szárítása. A legjobb szárítási eredmény eléréséhez kapcsolja be az XtraDry kiegészítő funkciót, majd válassza az AirDry lehetőséget.
MAGYAR Jelenség Lehetséges ok és megoldás Mosogatószer marad a prog‐ ram végén a mosogatószeradagolóban. • • • 49 A mosogatószer-tabletta beragadt az adagolóba, és ezért nem teljesen mosta ki a víz. A víz nem tudja kimosni a mosogatószert az adagoló‐ ból. Ellenőrizze, hogy a szórókar nincs-e eltömődve. Ellenőrizze, hogy a kosarakba helyezett eszközök nem akadályozzák-e a mosogatószer-adagoló fedelé‐ nek kinyitását. A készülék belsejében kelle‐ metlen szag észlelhető.
www.aeg.com Vízellátás Hidegvíz vagy melegvíz 2) maximum 60 °C Kapacitás Teríték 13 Energiafogyasztás Bekapcsolva hagyva (W) 5.0 Energiafogyasztás Kikapcsolt állapotban (W) 0.10 1) A további értékeket lásd az adattáblán. 2) Ha a melegvíz alternatív energiaforrásból származik (pl. napelemek, szélenergia), akkor az energiafo‐ gyasztás csökkentése érdekében használja a melegvíz-vezetéket. 14. KÖRNYEZETVÉDELMI TUDNIVALÓK A következő jelzéssel ellátott anyagokat hasznosítsa újra.
MAGYAR 51
117887891-A-222017 www.aeg.