FSE63600P NL EN FR USER MANUAL Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 25 47
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE......................................................................................... 2 2. VEILIGHEIDSVOORSCHRIFTEN.................................................................................4 3. BESCHRIJVING VAN HET PRODUCT........................................................................6 4. BEDIENINGSPANEEL................................................................................................. 7 5. PROGRAMMA....................
NEDERLANDS 3 niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • • • Houd rekening met het maximale aantal 13 plaatsen. Als de voedingskabel beschadigd is, moet de fabrikant, een erkende serviceverlener of een gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Leg het bestek in de besteklade met de scherpe randen naar beneden of leg ze horizontaal in de besteklade met de scherpe randen naar beneden. Laat om ongelukken te voorkomen het apparaat niet onbeheerd achter met open deur.
NEDERLANDS • • • • vervangen, dan moet dit gebeuren door onze Klantenservice. Steek de stekker pas in het stopcontact als de installatie is voltooid. Zorg ervoor dat het netsnoer na installatie bereikbaar is. Trek niet aan het netsnoer om het apparaat los te koppelen. Trek altijd aan de stekker. Dit apparaat voldoet aan de EUrichtlijnen. Alleen het Verenigd Koninkrijk en Ierland. Het apparaat is voorzien van een 13 ampère stekker.
www.aeg.com 3. BESCHRIJVING VAN HET PRODUCT 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Top sproeiarm Bovenste sproeiarm Onderste sproeiarm Filters Typeplaatje Zoutreservoir Luchtopening 3.1 Beam-on-Floor De Beam-on-Floor is een lichtstraal die op de vloer onder de deur van het apparaat verschijnt. • Wanneer het programma start, gaat de rode lichtstraal aan. De lichtstraal blijft gedurende het volledige programma zichtbaar. • Wanneer het programma is voltooid, gaat het groene lampje branden.
NEDERLANDS 7 4. BEDIENINGSPANEEL 2 1 1 2 3 4 5 Aan/uit-toets Weergave Delay-toets Program-toets ExtraHygiene-toets 3 6 7 8 9 4 5 6 7 8 9 TimeSaver-toets XtraDry-toets RESET-toets Indicatielampjes 4.1 Indicatielampjes Aanduiding Beschrijving Zoutindicatielampje. Dit is aan als het zoutreservoir bijgevuld dient te worden. Glansmiddelindicatielampje. Dit is aan als het glansmiddeldoseerbakje bijgevuld dient te worden. Einde-indicatielampje. Dit is aan als het wasprogramma is afgelopen. 5.
www.aeg.
NEDERLANDS Programma 1) Water (l) Energie(kWh) Duur (min.) P5 12 - 14 0.8 - 1.0 82 - 92 P4 10 0.9 30 P6 12 - 13 1.1 - 1.3 230 - 250 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Om de nodige informatie te ontvangen over het uitvoeren van prestatietesten (bijv. volgens EN60436) stuurt u een email naar: info.test@dishwasher-production.
www.aeg.com 6.2 De waterontharder De waterontharder verwijdert mineralen van de watertoevoer die een nadelige invloed hebben op de wasresultaten en het apparaat. Hoe hoger het gehalte van deze mineralen, des te harder is het water. De waterhardheid wordt gemeten in de volgende gelijkwaardige schalen. De waterontharder moet worden afgesteld op de hardheid van het water in uw woonplaats. Uw waterleidingbedrijf kan u informeren over de hardheid van het water in uw woonplaats.
NEDERLANDS Als het glansmiddelreservoir leeg is, gaat de glansmiddelindicator branden om aan te geven dat u glansmiddel moet bijvullen. Als u tevreden bent met de droogresultaten bij het gebruik van alleen multitabletten, kunt u de aanduiding voor het bijvullen van glansmiddel deactiveren. Voor de beste droogprestaties dient u echter altijd glansmiddel te gebruiken. Schakel de aanduiding in om de glansmiddelindicator actief te houden als u standaard wasmiddel of multitabletten zonder glansmiddel bevat.
www.aeg.com 2. Druk op om de instelling te wijzigen. 3. Druk op aan/uit om de instelling te bevestigen. 6.6 AirDry AirDry biedt goede droogresultaten met minder energieverbruik. AirDry wordt automatisch bij alle programma´s geactiveerd, behalve bij (indien van toepassing). Gebruik om de droogresultaten te verbeteren de optie XtraDry of activeer AirDry. LET OP! Als het apparaat toegankelijk is voor kinderen, adviseren wij u om AirDry te deactiveren, omdat het openen van de deur gevaarlijk kan zijn.
NEDERLANDS Als een optie niet van toepassing is op een programma, dan gaat het bijbehorende indicatielampje niet branden of het knippert even en gaat dan uit. Het activeren van opties kan van invloed zijn zowel op het water- en energieverbruik, als op de programmaduur. 7.1 XtraDry Activeer deze optie om de droogprestatie te versterken. XtraDry is een permanente optie voor alle programma´s anders dan . Het wordt in de volgende cycli automatisch geactiveerd.
www.aeg.com 8.1 Het zoutreservoir LET OP! Gebruik uitsluitend grof zout dat voor vaatwassers is gemaakt. Fijn zout verhoogt het risico op corrosie. Het zout wordt gebruikt om de hars in de waterontharder te herladen en voor goede wasresultaten voor dagelijks gebruik. Het zoutreservoir vullen 1. Draai de dop linksom om het zoutreservoir te openen. 2. Doe 1 liter water in het zoutreservoir (alleen de eerste keer). 3. Vul het zoutreservoir met vaatwasserzout (totdat het vol is).
NEDERLANDS Zorg dat het apparaat in de programmakeuzemodus staat. • Vul het zoutreservoir als het zoutindicatielampje brandt. • Vul het glansmiddeldoseerbakje als het indicatielampje van het glansmiddel brandt. 3. Ruim de korven in. 4. Voeg vaatwasmiddel toe. 5. U dient het juiste programma in te stellen en te starten voor het type lading en de mate van vervuiling. 9.1 Vaatwasmiddel gebruiken A B 15 apparaat in de keuzemodus Programma staat. 3.
www.aeg.com De uitgestelde start annuleren tijdens het aftellen Als u de uitgestelde start annuleert, moet u het programma en de opties opnieuw instellen. Houd tegelijkertijd RESET ingedrukt tot het apparaat in de programmakeuzemodus staat. Het programma annuleren Houd tegelijkertijd RESET ingedrukt tot het apparaat in de programmakeuzemodus staat. Controleer of er vaatwasmiddel in het vaatwasmiddelbakje aanwezig is voordat u een nieuw programma start.
NEDERLANDS 10.3 Wat moet u doen als u wilt stoppen met het gebruik van multitabletten Doe het volgende voordat u begint met het gebruiken van apart wasmiddel, zout en glansmiddel. 1. Stel het hoogste niveau van de waterontharder in. 2. Zorg ervoor dat het zout- en het glansmiddeldoseerbakje gevuld zijn. 3. Start het kortste programma met een spoelfase. Voeg geen afwasmiddel toe en ruim de mandjes niet in. 4. Als het programma is voltooid, wijzigt u de waterontharder in de waterhardheid van uw omgeving. 5.
www.aeg.com 11.1 De filters reinigen Het filtersystem bestaat uit 3 delen. C B A 1. Draai de filter (B) linksom en verwijder het. 5. Zorg ervoor dat er geen etensresten of vuil in of rond de rand van de opvangbak zitten. 6. Plaats de platte filter (A) terug. Zorg ervoor dat het goed onder de 2 geleidingen zit. 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. 2. Verwijder de filter (C) uit de filter (B). 3.
NEDERLANDS 11.2 De bovenste sproeiarm schoonmaken We raden u aan om de bovenste sproeiarm regelmatig schoon te maken om te voorkomen dat vuil de gaten verstopt. 19 naar boven en draai hem tegelijkertijd naar links totdat hij op zijn plaats vergrendelt. Verstopte gaten kunnen onbevredigende wasresultaten opleveren. 1. Trek het bovenrek naar buiten. 2. Druk om de sproeiarm van de mand los te maken de sproeiarm naar boven en draai hem tegelijkertijd naar rechts. 11.
www.aeg.com 12. PROBLEMEN OPLOSSEN WAARSCHUWING! Onjuiste reparatie van het apparaat kan een gevaar voor de veiligheid van de gebruiker vormen. Alle reparaties moeten worden uitgevoerd door bevoegd personeel. zonder contact op te nemen met een erkend servicecentrum. Zie de onderstaande tabel voor informatie over mogelijke problemen. Bij sommige problemen wordt er op de display een alarmcode weergegeven.
NEDERLANDS 21 Probleem en alarmcode Mogelijke oorzaak en oplossing Het apparaat stopt en start meerdere keren tijdens de werking. • Dat is normaal. Het voorziet in optimale reinigingsresultaten en energiebesparing. Het programma duurt te lang. • Als de optie uitgestelde start is ingesteld, annuleert u de uitgestelde start of wacht u tot het aftellen voorbij is. • Activeer de optie TimeSaver om de programmaduur te verkorten. • Het activeren van deze optie kan de duur van het programma verlengen.
www.aeg.com 12.1 De was- en droogresultaten zijn niet naar tevredenheid Storing Mogelijke oorzaak en oplossing Slechte wasresultaten. • Raadpleeg "Dagelijks gebruik", "Aanwijzingen en tips" en de folder voor het laden van de korf. • Gebruik intensievere wasprogramma´s. • Maak de inspuiters van de sproeiarm en het filter schoon. Zie "Onderhoud en reiniging". Slechte droogresultaten. • Serviesgoed heeft te lang in het gesloten apparaat gestaan.
NEDERLANDS 23 Storing Mogelijke oorzaak en oplossing Roestresten op bestek. • Er wordt voor het wassen teveel zout in het water gebruikt. Zie 'De waterontharder instellen'. • Zilver en roestvrijstalen bestek zijn samen geplaatst. Zet zilveren en roestvrijstalen voorwerpen niet dicht bij elkaar. Er bevinden zich aan het einde • De vaatwastablet raakte klem in het vaatwasmiddeldovan het programma resten van seerbakje en is daardoor niet volledig weggespoeld vaatwasmiddel in het vaatwasdoor het water.
www.aeg.com Voltage (V) 220 - 240 Frequentie (Hz) 50 bar (minimaal en maximaal) 0.5 - 8 MPa (minimaal en maximaal) 0.05 - 0.8 Watertoevoer Koud water of warm water 2) max. 60 °C Inhoud Couverts 13 Stroomverbruik Modus aan laten (W) 5.0 Uit-modus (W) 0.50 Elektrische aansluiting 1) Watertoevoerdruk 1) Zie het typeplaatje voor andere waarden. 2) Als het hete water door een alternatieve, milieuvriendelijkere energiebron geproduceerd wordt (bijv.
ENGLISH 25 CONTENTS 1. SAFETY INFORMATION........................................................................................... 25 2. SAFETY INSTRUCTIONS...........................................................................................27 3. PRODUCT DESCRIPTION.........................................................................................29 4. CONTROL PANEL..................................................................................................... 30 5. PROGRAMMES..........
www.aeg.com manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
ENGLISH • • • • • • • 27 If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
www.aeg.com • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. • UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses.
ENGLISH 3. PRODUCT DESCRIPTION 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Top spray arm Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 Beam-on-Floor The Beam-on-Floor is a light that is displayed on the floor below the appliance door. • When the programme starts, a red light comes on and stays on for the duration of the programme. • When the programme is completed, a green light comes on. • When the appliance has a malfunction, the red light flashes.
www.aeg.com 4. CONTROL PANEL 2 1 1 2 3 4 5 On/off button Display Delay button Program button ExtraHygiene button 3 6 7 8 9 4 5 6 7 8 9 TimeSaver button XtraDry button RESET button Indicators 4.1 Indicators Indicator Description Salt indicator. It is on when the salt container needs refilling. Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. End indicator. It is on when the programme is completed. 5.
ENGLISH Programme Degree of soil Type of load Programme phases Options P5 • Normal or light soil • Delicate crockery and glassware • Wash 45 °C • Rinses • Dry • XtraDry • Fresh soil • Crockery and cutlery • Wash 60 °C • Rinses • ExtraHygiene • XtraDry • Normal soil • Crockery and cutlery • • • • • XtraDry 4) P4 5) P6 6) Prewash Wash 50 °C Rinses Dry 31 1) This programme offers the most efficient use of water and energy consumption for crockery and cutlery with normal soil.
www.aeg.com Programme 1) Water (l) Energy (kWh) Duration (min) P6 12 - 13 1.1 - 1.3 230 - 250 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes To receive the necessary information for conducting performance tests (e.g. according to EN60436), send an email to: info.test@dishwasher-production.
ENGLISH 33 Water hardness German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
www.aeg.com – = the rinse aid empty notification is activated. 2. Press to change the setting. 3. Press on/off to confirm the setting. 6.4 The rinse aid level It is possible to set the released quantity of rinse aid between level 1 (minimum quantity) and level 6 (maximum quantity). Level 0 deactivates the rinse aid dispenser and no rinse aid is released. Factory setting: level 4. How to set the rinse aid level Make sure the appliance is in user mode. 1. Press • The indicators , , and are off.
ENGLISH CAUTION! If children have access to the appliance, it is advised to deactivate AirDry as opening the door may pose a danger. How to deactivate AirDry Make sure the appliance is in user mode. 1. Press . • The indicators , , 35 and are off. • The indicator still flashes. • The display shows the current setting. – = AirDry is deactivated. – = AirDry is activated. to change the setting. 2. Press 3. Press on/off to confirm the setting. 7.
www.aeg.com 7.3 ExtraHygiene How to activate ExtraHygiene This option provides better hygiene results by keeping the temperature at 70 °C for at least 10 minutes during the last rinsing phase. Press . The related indicator is on. The display shows the updated programme duration. 8. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3.
ENGLISH 8.2 How to fill the rinse aid dispenser A B 37 CAUTION! Only use rinse aid designed specifically for dishwashers. 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent excessive foam formation. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) is clear. C 9. DAILY USE 1. Open the water tap. 2.
www.aeg.com approximately 3 seconds and then shows the programme duration. 4. Set the applicable options. 5. Close the appliance door to start the programme. Press and hold RESET until the appliance is in programme selection mode. Cancelling the programme 1. Set a programme. Press and hold RESET until the appliance is in programme selection mode. Make sure that there is detergent in the detergent dispenser before you start a new programme. 2.
ENGLISH • Always use the whole space of the baskets. • Make sure that items in the baskets do not touch or cover each other. Only then can the water completely reach and wash the dishes. • You can use dishwasher detergent, rinse aid and salt separately or you can use the multi-tablets (e.g. ''All in 1''). Follow the instructions on the packaging. • Select a programme according to the type of load and the degree of soil. offers the most efficient use of water and energy consumption. 10.
www.aeg.com 10.6 Unloading the baskets 1. Let the tableware cool down before you remove it from the appliance. Hot items can be easily damaged. 2. First remove items from the lower basket, then from the upper basket. After the programme is completed, water can still remain on the inside surfaces of the appliance. 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket.
ENGLISH 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 41 3. Wash the spray arm under running water. Use a thin pointed tool, e.g. a toothpick, to remove particles of soil from the holes. 4. To install the spray arm back, press the spray arm upwards and simultaneously turn it counterclockwise until it locks into place. 11.
www.aeg.com 11.4 Internal cleaning • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth. • To maintain the performance of your appliance, use a cleaning product designed specifically for dishwashers at least once a month. Carefully follow the instructions on the packaging of the product. • Do not use abrasive products, abrasive cleaning pads, sharp tools, strong chemicals, scourer or solvents.
ENGLISH Problem and alarm code Possible cause and solution The anti-flood device is on. • Close the water tap and contact an Authorised Service Centre. The display shows . 43 The appliance stops and • It is normal. It provides optimal cleaning results and enstarts more times during opergy savings. eration. The programme lasts too long. • If the delay start option is set, cancel the delay setting or wait for the end of the countdown. • Activate the TimeSaver option to reduce the programme duration.
www.aeg.com 12.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results. • Refer to "Daily use", "Hints and tips" and the basket loading leaflet. • Use more intensive washing programmes. • Clean spray arm jets and the filter. Refer to "Care and Cleaning". Poor drying results. • Tableware has been left for too long inside the closed appliance. • There is no rinse aid or the dosage of rinse aid is not sufficient.
ENGLISH 45 Problem Possible cause and solution There are residues of detergent in the dispenser at the end of the programme. • The detergent tablet got stuck in the dispenser and was not completely washed away by water. • Water cannot wash away the detergent from the dispenser. Make sure that the spray arm is not blocked or clogged. • Make sure that items in the baskets do not impede the lid of the detergent dispenser from opening. Odours inside the appliance. • Refer to "Internal cleaning".
www.aeg.com Power consumption Left-on mode (W) 5.0 Off-mode (W) 0.50 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to decrease energy consumption. 14. ENVIRONMENTAL CONCERNS Recycle materials with the symbol . Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances.
FRANÇAIS 47 TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................47 2. CONSIGNES DE SÉCURITÉ......................................................................................49 3. DESCRIPTION DE L'APPAREIL.................................................................................51 4. BANDEAU DE COMMANDE....................................................................................52 5. PROGRAMMES.......................
www.aeg.com pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.1 Sécurité des enfants et des personnes vulnérables.
FRANÇAIS • • • • • • • • • 49 La pression de l'eau en fonctionnement (minimale et maximale) doit se situer entre 0.5 (0.05) / 8 (0.8) bar (MPa) Respectez le nombre maximal de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger.
www.aeg.com • L'appareil doit être relié à la terre. • Vérifiez que les paramètres figurant sur la plaque signalétique correspondent aux données électriques de votre réseau. • Utilisez toujours une prise de courant de sécurité correctement installée. • N'utilisez pas d'adaptateurs multiprises ni de rallonges. • Veillez à ne pas endommager la fiche secteur ni le câble d'alimentation. Le remplacement du câble d'alimentation de l'appareil doit être effectué par notre service après-vente agréé.
FRANÇAIS 2.6 Mise au rebut 51 • Coupez le câble d'alimentation et mettez-le au rebut. • Retirez le dispositif de verrouillage de la porte pour empêcher les enfants et les animaux de s'enfermer dans l'appareil. AVERTISSEMENT! Risque de blessure ou d'asphyxie. • Débranchez l'appareil de l'alimentation électrique. 3.
www.aeg.com La projection au sol peut être partiellement visible lorsque le mode AirDry est activé durant la phase de séchage. Pour savoir si le cycle est terminé, regardez le bandeau de commande. 4. BANDEAU DE COMMANDE 2 1 1 2 3 4 5 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche ExtraHygiene 3 6 7 8 9 4 5 6 7 8 9 Touche TimeSaver Touche XtraDry Touche RESET Voyants 4.1 Voyants Indicateur Description Voyant du réservoir de sel régénérant.
FRANÇAIS Programme Degré de salissure Type de vaisselle Phases du programme Options P2 • Tous • Vaisselle, couverts, plats et casseroles • Prélavage • Lavage de 45 °C à 70 °C • Rinçages • Séchage • ExtraHygiene • XtraDry • Très sale • Vaisselle, couverts, plats et casseroles • • • • • ExtraHygiene • TimeSaver • XtraDry • Normalement ou légèrement sale • Vaisselle fragile et verres • Lavage à 45 °C • Rinçages • Séchage 2) P3 3) P5 4) P4 5) P6 6) Prélavage Lavage à 70 °C Rinçages Séchage •
www.aeg.com Eau (l) Consommation électrique (kWh) Durée (min) P2 8 - 15 0.7 - 1.7 46 - 170 P3 12.5 - 14.5 1.4 - 1.7 170 - 190 P5 12 - 14 0.8 - 1.0 82 - 92 P4 10 0.9 30 P6 12 - 13 1.1 - 1.3 230 - 250 Programme 1) 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
FRANÇAIS 6.2 Adoucisseur d'eau sélection de programme. Dans le cas contraire, définissez le mode de sélection de programme de la manière suivante : L'adoucisseur d'eau élimine les minéraux de l'arrivée d'eau qui pourraient avoir un impact négatif sur les résultats de lavage et sur l'appareil. Maintenez la touche RESET enfoncée jusqu'à ce que l'appareil passe en mode Programmation. Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence.
www.aeg.com • Les voyants sont éteints. , , et • Le voyant clignote toujours. • L'affichage indique le réglage actuel : Par ex., = niveau 5. plusieurs 2. Appuyez sur la touche fois pour modifier le réglage. 3. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.3 Notification du réservoir de liquide de rinçage vide Le liquide de rinçage permet à la vaisselle de sécher sans traces ni taches. Il est libéré automatiquement au cours de la phase de rinçage chaud.
FRANÇAIS défaut, ce signal sonore est désactivé, mais il est possible de l'activer. Comment activer le signal sonore de fin de programme Assurez-vous que l'appareil est en mode Utilisateur. 1. Appuyez sur • Les voyants sont éteints. . , , et • Le voyant clignote toujours. • L'affichage indique le réglage actuel. – = le signal sonore est désactivé. – = le signal sonore est activé. 2. Appuyez sur pour modifier le réglage. 3. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.
www.aeg.com 7. OPTIONS Les options souhaitées doivent être activées à chaque fois, avant de lancer un programme. Vous ne pouvez pas activer ni désactiver ces options pendant le déroulement d'un programme. Toutes les options ne sont pas compatibles les unes avec les autres. Si vous sélectionnez des options non compatibles, l'appareil désactive automatiquement une ou plusieurs de ces options. Seuls les voyants correspondant aux options toujours activées restent allumés.
FRANÇAIS 59 8. AVANT LA PREMIÈRE UTILISATION 1. Assurez-vous que le réglage actuel de l'adoucisseur d'eau est compatible avec la dureté de l'arrivée d'eau. Si ce n'est pas le cas, réglez le niveau de l'adoucisseur d'eau. 2. Remplissez le réservoir de sel régénérant. 3. Remplissez le distributeur de liquide de rinçage. 4. Ouvrez le robinet d'eau. 5. Lancez un programme pour éliminer tous les résidus qui peuvent toujours se trouver à l'intérieur de l'appareil.
www.aeg.com 8.2 Comment remplir le distributeur de liquide de rinçage A ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. B 1. Ouvrez le couvercle (C). 2. Remplissez le distributeur (B) jusqu'à ce que le liquide de rinçage atteigne le repère « MAX ». 3. Si le liquide de rinçage déborde, épongez-le avec un chiffon absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement.
FRANÇAIS petite quantité de produit de lavage à l'intérieur de la porte de l'appareil. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. 9.2 Réglage et départ d'un programme Départ d'un programme 1. Laissez la porte de l'appareil entrouverte. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. 3. Appuyez à plusieurs reprises sur la jusqu'à ce que le numéro touche du programme sélectionné s'affiche.
www.aeg.com automatiquement l'appareil lorsqu'il ne fonctionne pas. La fonction s'active : • 5 minutes après la fin du programme de lavage. • Au bout de 5 minutes si le programme n'a pas démarré. 10. CONSEILS 10.1 Raccordement Suivez les conseils ci-dessous pour garantir des résultats de lavage et de séchage optimaux au quotidien, et pour vous aider à protéger l'environnement. • Videz les plus gros résidus alimentaires des plats dans une poubelle. • Ne rincez pas vos plats à la main au préalable.
FRANÇAIS 10.4 Chargement des paniers • N'utilisez l'appareil que pour laver des articles adaptés au lave-vaisselle. • Ne lavez pas au lave-vaisselle des articles en bois, en corne, en aluminium, en étain et en cuivre. • Ne placez pas dans l'appareil des objets pouvant absorber l'eau (éponges, chiffons de nettoyage). • Retirez les plus gros résidus alimentaires des plats. • Faites tremper la vaisselle contenant des aliments brûlés avant de la placer dans l'appareil.
www.aeg.com 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 5.
FRANÇAIS 65 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur 3. Nettoyez le bras d'aspersion à l'eau courante. Utilisez un outil pointu comme un cure-dent pour extraire toutes les particules de saleté incrustées dans les orifices. 4.
www.aeg.com 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT AVERTISSEMENT! Une mauvaise réparation de l'appareil peut entraîner un danger pour la sécurité de l'utilisateur. Toute réparation ne doit être effectuée que par un technicien qualifié. Reportez-vous au tableau ci-dessous pour obtenir plus d'informations sur les problèmes possibles. Pour certaines anomalies, l'écran affiche un code d'alarme. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé.
FRANÇAIS 67 Problème et code d'alarme Cause et solution possibles L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps. • Si vous avez sélectionné l'option de départ différé, annulez-le ou attendez la fin du décompte. • Activez l'option TimeSaver pour réduire la durée du programme. • Activer certaines options peut rallonger la durée du programme.
www.aeg.com 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
FRANÇAIS 69 Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage spécialement conçus pour les lave-vaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après-vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ».
www.aeg.com Reportez-vous aux chapitres « Avant la première utilisation », « Utilisation quotidienne » ou « Conseils » pour connaître les autres causes probables. 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 818 - 898 / 550 Branchement électrique1) Tension (V) 220 - 240 Fréquence (Hz) 50 bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude2) max.
FRANÇAIS 71
117885752-A-232018 www.aeg.