FSE63600P NL EN FR USER MANUAL Gebruiksaanwijzing Afwasautomaat User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 25 47
www.aeg.com INHOUDSOPGAVE 1. VEILIGHEIDSINFORMATIE......................................................................................... 3 2. VEILIGHEIDSVOORSCHRIFTEN.................................................................................4 3. BESCHRIJVING VAN HET PRODUCT........................................................................6 4. BEDIENINGSPANEEL................................................................................................. 7 5. PROGRAMMA’S..................
NEDERLANDS 1. 3 VEILIGHEIDSINFORMATIE Lees zorgvuldig de meegeleverde instructies voor installatie en gebruik van het apparaat. De fabrikant is niet verantwoordelijk voor letsel of schade veroorzaakt door een verkeerde installatie of verkeerd gebruik. Bewaar de instructies altijd op een veilige en toegankelijke plaats voor toekomstig gebruik. 1.
www.aeg.com • • • • • • • Als de voedingskabel beschadigd is, moet de fabrikant, een erkende serviceverlener of een gekwalificeerd persoon deze vervangen teneinde gevaarlijke situaties te voorkomen. Doe messen en bestek met scherpe punten in het bestekmandje met de punten omlaag in horizontale positie. Laat de deur van het apparaat niet open staan zonder toezicht om te voorkomen dat er iemand over struikelt.
NEDERLANDS • Trek niet aan het netsnoer om het apparaat los te koppelen. Trek altijd aan de stekker. • Dit apparaat voldoet aan de EEGrichtlijnen. • Alleen voor VK en Ierland. Het apparaat heeft een stekker van 13 ampère. Als de zekering van de stekker verwisseld moet worden, gebruik dan zekering: 13 amp ASTA (BS 1362). 2.3 Aansluiting aan de waterleiding • Beschadig de waterslangen niet.
www.aeg.com 3. BESCHRIJVING VAN HET PRODUCT 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Top sproeiarm Bovenste sproeiarm Onderste sproeiarm Filters Typeplaatje Zoutreservoir Luchtopening 3.1 Beam-on-Floor De Beam-on-Floor is een lichtstraal die op de vloer onder de deur van het apparaat verschijnt. • Wanneer het programma start, gaat de rode lichtstraal aan. De lichtstraal blijft gedurende het volledige programma zichtbaar. • Wanneer het programma is voltooid, gaat het groene lampje branden.
NEDERLANDS 4. BEDIENINGSPANEEL 2 1 1 2 3 4 5 Aan/uit-toets Weergave Delay-toets Program-toets Sanitize-toets 3 6 7 8 9 4 5 6 7 8 9 TimeSaver-toets XtraDry-toets Reset-toets Indicatielampjes 4.1 Indicatielampjes Aanduiding Beschrijving Einde-indicatielampje. Glansmiddelindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. Zoutindicatielampje. Dit indicatielampje is altijd uit als het programma in werking is. 5.
www.aeg.com Programma Mate van vervuiling Type lading Programmafasen Opties P5 • Normaal of licht bevuild • Teer serviesgoed en glaswerk • Wassen 45°C • Spoeling • Drogen • XtraDry • Pas bevuild • Serviesgoed en bestek • Wassen 60°C • Spoeling • Sanitize • XtraDry • Normaal bevuild • Voorspoelen • Serviesgoed en • Wassen 50°C bestek • Spoeling • Drogen • XtraDry P4 3) P6 4) 1) Dit programma biedt het meest efficiënte water- en energieverbruik voor normaal vervuild serviesgoed en bestek.
NEDERLANDS Programma 1) Water (l) Energie (kWh) Bereidingsduur (min) P6 9 - 10 1.1 - 1.3 219 - 229 9 1) De druk en temperatuur van het water, de variaties in stroomtoevoer, de opties en de hoeveelheid vaat kan de verbruikswaarden veranderen. 5.2 Aanwijzingen voor testinstituten Stuur voor alle benodigde informatie over testprestaties een e-mail naar: info.test@dishwasher-production.com Schrijf het productnummer (PNC) op dat u op het typeplaatje vindt. 6. INSTELLINGEN 6.
www.aeg.com Waterhardheid Duitse graden (°dH) Franse graden (°fH) mmol/l Clarke-graden Wateronthardingsniveau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
NEDERLANDS 1. Houd om de gebruikersmodus in te 1. Houd om de gebruikersmodus in te voeren tegelijkertijd voeren tegelijkertijd en ingedrukt tot de indicatielampjes , , , en gaan knipperen en het display blanco is. 2. Druk op en , , gaan uit. • Het indicatielampje blijft knipperen. • Het display toont de huidige instelling: bijv. = niveau 4. – De glansmiddelniveaus lopen van 0A tot 6A. – Niveau 0 = er wordt geen glansmiddel gebruikt. 3. Druk herhaaldelijk op om de instelling te wijzigen. 4.
www.aeg.com • Het indicatielampje blijft knipperen. • Het display toont de huidige instelling: uit. 3. Druk op wijzigen. = Geluidssignaal om de instelling te = Geluidssignaal aan. 4. Druk op de knop aan/uit om de instelling te bevestigen. 6.6 AirDry AirDry biedt goede droogresultaten met minder energieverbruik. Gebruik om de droogresultaten te verbeteren de optie XtraDry of activeer AirDry. Het deactiveren van AirDry Het apparaat moet in de programmakeuzemodus staan. 1.
NEDERLANDS Niet alle opties kunnen met elkaar worden gecombineerd. Als u opties hebt geselecteerd die niet met elkaar te combineren zijn, dan schakelt het apparaat automatisch één of meerdere opties uit. Alleen de indicatielampjes van de actieve opties blijven aan. 7.1 XtraDry Activeer deze optie als u het droogresultaat een boost wilt geven. Bij het gebruik van deze optie kunnen de duur van sommige programma's, het waterverbruik en de temperatuur van de laatste spoeling worden beïnvloed.
www.aeg.com 3. Vul het glansmiddeldoseerbakje. 4. Draai de waterkraan open. 5. Start een programma om resten te verwijderen die misschien nog in het apparaat zijn achtergebleven. Gebruik geen afwasmiddel en gebruik de mandjes niet. Als u een programma start, doet het apparaat er ongeveer 5 minuten over om de hars in de waterontharder te herladen. Het lijkt alsof het apparaat niet werkt. De wasfase start pas nadat deze procedure voltooid is. De procedure wordt periodiek herhaald. 8.
NEDERLANDS Vul het glansmiddeldoseerbakje bij wanneer de indicatie (A) helder wordt. 15 Als u multitabletten gebruikt en het droogresultaat is naar tevredenheid, kan de indicatie voor het glansmiddel worden uitgeschakeld. We raden u aan altijd glansmiddel te gebruiken voor een betere droogprestatie, zelfs in combinatie met wastabletten die glansmiddel bevatten. 9. DAGELIJKS GEBRUIK 1. Draai de waterkraan open. 2. Druk op de aan-/uittoets om het apparaat te activeren.
www.aeg.com programma worden op het display 3 seconden weergegeven. 4. Stel de bruikbare opties in. 5. Sluit de deur van de afwasmachine om het programma te starten. Een programma starten met een uitgestelde start 1. Stel een programma in. 2. Blijf op drukken tot het display de uitgestelde tijd toont die u wilt instellen (van 1 tot 24 uur). Het controlelampje startuitstel gaat branden. 3. Sluit de deur van het apparaat om het aftellen te starten.
NEDERLANDS multitabletten (bijv. ''3in1'', ''4in1'', ''All in 1''). Volg de aanwijzing op de verpakking. • U dient het juiste programma in te stellen voor het type lading en de mate van vervuiling. Het programma ECO biedt het meest efficiënte wateren energieverbruik voor normaal vervuild serviesgoed en bestek. 10.2 Gebruik van zout, glansmiddel en vaatwasmiddel • Gebruik enkel zout, glansmiddel en vaatwasmiddel voor afwasautomaten. Overige producten kunnen het apparaat beschadigen.
www.aeg.com 10.6 De rekken uitruimen Aan het einde van het programma kan er water aan de zijkanten en de deur van het apparaat achterblijven. 1. Laat de borden afkoelen voordat u deze uit het apparaat neemt. Hete borden zijn gevoelig voor beschadigingen. 2. Ruim eerst het onderrek en dan het bovenrek uit. 11. ONDERHOUD EN REINIGING WAARSCHUWING! Schakel het apparaat uit en trek de stekker uit het stopcontact voordat u onderhoudshandelingen verricht.
NEDERLANDS 7. Plaats de filters (B) en (C) terug. 8. Plaats de filter (B) terug in de platte filter (A). Rechtsom draaien tot het vastzit. LET OP! Een onjuiste plaatsing van de filters kan leiden tot slechte wasresultaten en het apparaat beschadigen. 11.2 De bovenste sproeiarm schoonmaken 3. Reinig de sproeiarm onder stromend water. Gebruik een smal en puntig gereedschap, bijv. een tandenstoker, om de vuildeeltjes uit de gaten te verwijderen. 4.
www.aeg.com • Gebruik geen schuurmiddelen, schuursponsjes of oplosmiddelen. 11.4 De binnenkant van de machine reinigen • Reinig het apparaat zorgvuldig, inclusief de rubberen afdichting van de deur, met een zachte, vochtige doek. • Als u regelmatig korte programma's gebruikt dan kunnen er vetresten en kalkaanslag achterblijven in het apparaat. Om dit te voorkomen raden wij aan om minstens twee keer per maand langdurige programma´s te gebruiken.
NEDERLANDS Probleem en alarmcode Mogelijke oorzaak en oplossing Het apparaat pompt geen water weg. Op het display verschijnt • • • • . 21 Controleer of de gootsteenafvoer niet verstopt is. Controleer of het filter in de afvoerslang niet verstopt is. Controleer of het binnenfiltersysteem niet verstopt is. Controleer of er geen knikken of bochten in de waterafvoerslang aanwezig zijn. De anti-overstromingsbevei- • Draai de waterkraan dicht en neem contact op met de liging is aan. service-afdeling.
www.aeg.com Voor alarmcodes die niet in de tabel vermeld zijn, neemt u contact op met de service-afdeling. 12.1 De was- en droogresultaten zijn niet naar tevredenheid Probleem Mogelijke oorzaak en oplossing Slechte wasresultaten. • Raadpleeg "Dagelijks gebruik", "Aanwijzingen en tips" en de folder voor het laden van de korf. • Gebruik intensievere wasprogramma´s. • Maak de inspuiters van de sproeiarm en het filter schoon. Zie "Onderhoud en reiniging". Slechte droogresultaten.
NEDERLANDS 23 Probleem Mogelijke oorzaak en oplossing Roestresten op bestek. • Er wordt voor het wassen teveel zout in het water gebruikt. Zie 'De waterontharder instellen'. • Zilver en roestvrijstalen bestek zijn samen geplaatst. Zet zilveren en roestvrijstalen voorwerpen niet dicht bij elkaar. Er bevinden zich aan het einde • De vaatwastablet raakte klem in het vaatwasmiddeldovan het programma resten van seerbakje en is daardoor niet volledig weggespoeld vaatwasmiddel in het vaatwasdoor het water.
www.aeg.com Watertoevoerdruk bar (minimaal en maximaal) 0.5 - 8 MPa (minimaal en maximaal) 0.05 - 0.8 Watertoevoer Koud water of warm water 2) max. 60 °C Vermogen Couverts 13 Energieverbruik Modus aan laten (W) 5.0 Energieverbruik Uit-modus (W) 0.10 1) Zie het typeplaatje voor andere waarden. 2) Als het hete water door een alternatieve, milieuvriendelijkere energiebron geproduceerd wordt (bijv.
ENGLISH 25 CONTENTS 1. SAFETY INFORMATION........................................................................................... 26 2. SAFETY INSTRUCTIONS...........................................................................................27 3. PRODUCT DESCRIPTION.........................................................................................29 4. CONTROL PANEL..................................................................................................... 30 5. PROGRAMMES..........
1. www.aeg.com SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
ENGLISH • • • • • • 27 Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
www.aeg.com • Ensure that there are no visible water leaks during and after the first use of the appliance. • The water inlet hose has a safety valve and a sheath with an inner mains cable. completed. There can be detergent on the dishes. • The appliance can release hot steam if you open the door while a programme operates. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. 2.5 Service WARNING! Dangerous voltage.
ENGLISH 3. PRODUCT DESCRIPTION 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Top spray arm Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 Beam-on-Floor The Beam-on-Floor is a light that is displayed on the floor below the appliance door. • When the programme starts, a red light comes on and stays on for the duration of the programme. • When the programme is completed, a green light comes on. • When the appliance has a malfunction, the red light flashes.
www.aeg.com 4. CONTROL PANEL 2 1 1 2 3 4 5 On/off button Display Delay button Program button Sanitize button 3 6 7 8 9 4 5 6 7 8 9 TimeSaver button XtraDry button Reset button Indicators 4.1 Indicators Indicator Description End indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. 5.
ENGLISH Programme Degree of soil Type of load Programme phases Options P5 • Normal or light soil • Delicate crockery and glassware • Wash 45 °C • Rinse • Dry • XtraDry • Fresh soil • Crockery and cutlery • Wash 60 °C • Rinse • Sanitize • XtraDry • Normal soil • Crockery and cutlery • • • • • XtraDry P4 3) P6 4) Prewash Wash 50 °C Rinse Dry 31 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil.
www.aeg.com 5.2 Information for test institutes info.test@dishwasher-production.com For all the necessary information for test performance, send an email to: Write down the product number (PNC) that is on the rating plate. 6. SETTINGS 6.1 Programme selection mode and user mode When the appliance is in programme selection mode it is possible to set a programme and to enter the user mode.
ENGLISH 33 German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level. Whether you use a standard detergent or multi-tabs (with or without salt), set the proper water hardness level to keep the salt refill indicator active. Multi-tabs containing salt are not effective enough to soften hard water.
www.aeg.com When rinse aid chamber is empty, the rinse aid indicator is turned on notifying to refill rinse aid. If you are using multitabs containing rinse aid and you are satisfied with the drying result, you can deactivate the notification for refilling rinse aid. However, we recommend that you always use rinse aid for best drying performance. If you use standard detergent or multitablets without rinse aid, activate the notification to keep the rinse aid refill indicator active.
ENGLISH the indicators CAUTION! Do not try to close the appliance door within 2 minutes after automatic open. This can cause damage to the appliance. 2. Press , and . • The indicators How to deactivate AirDry The appliance must be in programme selection mode. 1. To enter the user mode, press and and , start to flash and the display is blank. To improve the drying performance refer to the XtraDry option or activate AirDry. hold simultaneously , 35 until , , and go off.
www.aeg.com How to activate TimeSaver Press , the related indicator comes on. If the option is not applicable to the programme, the related indicator does not come on or it flashes quickly for a few seconds and then goes off. The display shows the updated programme duration. 7.3 Sanitize This option provides better hygiene results by keeping the temperature at 70 °C for at least 10 minutes during the last rinsing phase.
ENGLISH 8.2 How to fill the rinse aid dispenser A B 37 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) becomes clear. If you use multi-tablets and the drying performance is satisfactory, the rinse aid refill indication can be disabled.
www.aeg.com detergent on the inner part of the appliance door. 4. Close the lid. Make sure that the lid locks into position. 9.2 Setting and starting a programme The Auto Off function This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation: • 5 minutes after the completion of the programme. • After 5 minutes if the programme has not started. Starting a programme 1. Keep the appliance door ajar. 2.
ENGLISH 39 10. HINTS AND TIPS 10.1 General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase. • Always use the whole space of the baskets.
www.aeg.com • Make sure that the spray arms can move freely before you start a programme. 10.5 Before starting a programme Make sure that: • The filters are clean and correctly installed. • The cap of the salt container is tight. • The spray arms are not clogged. • There is dishwasher salt and rinse aid (unless you use multi- tablets). • The position of the items in the baskets is correct. • The programme is applicable for the type of load and for the degree of soil.
ENGLISH 41 11.2 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. Clogged holes can cause unsatisfactory washing results. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 1. Pull out the upper basket. 2.
www.aeg.com 11.4 Internal cleaning 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth. • If you use short duration programmes regularly, these can leave deposits of grease and limescale inside the appliance.
ENGLISH 43 Problem and alarm code Possible cause and solution The appliance does not fill with water. • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the filter in the inlet hose is not clogged. • Make sure that the inlet hose has no kinks or bends. The display shows . The appliance does not drain the water.
www.aeg.com Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes. Once you have checked the appliance, deactivate and activate the appliance. If the problem occurs again, contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre. 12.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results.
ENGLISH 45 Problem Possible cause and solution Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener". • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together. There are residues of detergent in the dispenser at the end of the programme. • The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
www.aeg.com Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 5.0 Power consumption Off-mode (W) 0.10 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption. 14. ENVIRONMENTAL CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it.
FRANÇAIS 47 TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................48 2. CONSIGNES DE SÉCURITÉ......................................................................................49 3. DESCRIPTION DE L'APPAREIL.................................................................................51 4. BANDEAU DE COMMANDE....................................................................................52 5. PROGRAMMES.......................
1. www.aeg.com INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
FRANÇAIS • • • • • • • • 49 Respectez le nombre maximal de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
www.aeg.com changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant d'installer des tuyaux neufs, des tuyaux n'ayant pas servi depuis longtemps, lorsqu'une réparation a été effectuée ou qu'un nouveau dispositif a été installé (compteurs d'eau, etc.), laissez l'eau s'écouler jusqu'à ce qu'elle soit parfaitement propre et claire.
FRANÇAIS 3. DESCRIPTION DE L'APPAREIL 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Bras d'aspersion supérieur Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 3.1 Beam-on-Floor Le faisceau Beam-on-Floor est une lumière projetée sur le sol, sous la porte de l'appareil. • Lorsque le programme démarre, le faisceau rouge s'allume et reste allumé pendant toute la durée du programme.
www.aeg.com 4. BANDEAU DE COMMANDE 2 1 1 2 3 4 5 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche Sanitize 3 6 7 8 9 4 5 6 7 8 9 Touche TimeSaver Touche XtraDry Touche Reset Voyants 4.1 Voyants Indicateur Description Voyant de fin. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. 5.
FRANÇAIS Programme Degré de salissure Phases du programType de vaisselle me Options P5 • Normalement ou légèrement sale • Vaisselle fragile et verres • Lavage à 45 °C • Rinçage • Séchage • XtraDry • Vaisselle fraîche- • Lavage à 60 °C ment salie • Rinçage • Vaisselle et couverts • Sanitize • XtraDry • Normalement sale • Vaisselle et couverts • XtraDry P4 3) P6 4) • • • • Prélavage Lavage à 50 °C Rinçage Séchage 53 1) Ce programme vous permet d'optimiser votre consommation d'eau et d'énergie
www.aeg.com Programme 1) P6 Eau (l) Consommation électrique (kWh) Durée (min) 9 - 10 1.1 - 1.3 219 - 229 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.2 Informations pour les instituts de test Pour toute information relative aux performances de test, envoyez un courrier électronique à l'adresse : info.
FRANÇAIS 55 Dureté eau Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Niveau de l'adoucisseur d'eau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
www.aeg.com Comment régler le niveau de liquide de rinçage le voyant Remplissage du liquide de rinçage reste actif. L'appareil doit être en mode Programmation. Comment désactiver la notification du distributeur de liquide de rinçage vide 1. Pour entrer en mode utilisateur, maintenez les touches et enfoncées simultanément jusqu'à ce , que les voyants , , et se mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants s'éteignent. .
FRANÇAIS que les voyants , , , et commencent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants s'éteignent. , , et • Le voyant continue à clignoter. • L'affichage indique le réglage actuel : désactivé. 3. Appuyez sur réglage. = Signal sonore pour modifier le = Signal sonore activé. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.6 AirDry L'option AirDry améliore les résultats de séchage en utilisant moins d'énergie.
www.aeg.com 7.1 XtraDry Activez cette option lorsque vous voulez améliorer les performances de séchage. En utilisant cette option, la durée de certains programmes, la consommation d'eau et la température du dernier rinçage peuvent être affectés. L'option XtraDry est une option permanente pour tous les programmes, à l'exception du programme pour lequel elle doit être sélectionnée à chaque cycle.
FRANÇAIS se trouver à l'intérieur de l'appareil. N'utilisez pas de produit de lavage et ne chargez pas les paniers. Lorsque vous démarrez un programme, l'appareil peut prendre 5 minutes pour recharger la résine dans l'adoucisseur d'eau. Pendant ce temps, l'appareil semble ne pas fonctionner. La phase de lavage ne démarre qu'une fois cette procédure achevée. La procédure sera répétée régulièrement. 8.
www.aeg.com 2. Remplissez le distributeur (B) jusqu'à ce que le liquide de rinçage atteigne le repère « MAX ». 3. Si le liquide de rinçage déborde, épongez-le avec un chiffon absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. Si vous utilisez des pastilles de détergent multifonctions et que les performances du séchage sont satisfaisantes, l'indication de remplissage du liquide de rinçage peut être désactivée.
FRANÇAIS Départ d'un programme 1. Laissez la porte de l'appareil entrouverte. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. 3. Appuyez à plusieurs reprises sur la touche jusqu'à ce que l'affichage indique le numéro du programme que vous souhaitez lancer. Le numéro du programme s'affiche pendant environ 3 secondes, puis la durée du programme s'affiche. 4. Sélectionnez les options compatibles. 5.
www.aeg.com 10. CONSEILS 10.1 Raccordement Les conseils suivants vous garantissent des résultats de lavage et de séchage optimaux au quotidien, et vous aideront à protéger l'environnement. • Videz les plus gros résidus alimentaires des plats dans une poubelle. • Ne rincez pas vos plats à la main au préalable. En cas de besoin, utilisez le programme de prélavage (si disponible) ou sélectionnez un programme avec une phase de prélavage. • Utilisez toujours tout l'espace des paniers.
FRANÇAIS • Ne mettez pas dans le lave-vaisselle des articles en bois, en corne, en aluminium, en étain et en cuivre. • Ne placez pas dans l'appareil des objets pouvant absorber l'eau (éponges, chiffons de nettoyage). • Retirez les gros résidus alimentaires des plats et jetez-les à la poubelle. • Laissez tremper les casseroles contenant des restes d'aliments brûlés. • Chargez les articles creux (tasses, verres et casseroles) en les retournant.
www.aeg.com 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 5.
FRANÇAIS 65 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur 3. Nettoyez le bras d'aspersion à l'eau courante. Utilisez un outil pointu comme un cure-dent pour extraire toutes les particules de saleté incrustées dans les orifices.
www.aeg.com problème par vous-même à l'aide des informations du tableau. AVERTISSEMENT! Des réparations mal entreprises peuvent entraîner un grave danger pour l'utilisateur. Toute réparation ne doit être effectuée que par un technicien qualifié. Pour certaines anomalies, l'écran affiche un code d'alarme. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé. Problème et code d'alarme Cause et solution possibles L'appareil ne s'allume pas.
FRANÇAIS 67 Problème et code d'alarme Cause et solution possibles Le programme dure trop longtemps. • Sélectionnez l'option TimeSaver pour raccourcir la durée du programme. • Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte. Le temps restant sur l'affi• Ceci est normal. L'appareil fonctionne correctement. chage augmente et passe presque instantanément à la fin du programme. Petite fuite au niveau de la porte de l'appareil. • L'appareil n'est pas de niveau.
www.aeg.com 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
FRANÇAIS 69 Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage pour lavevaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble.
www.aeg.com 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 818-898 / 550 Branchement électrique1) Tension (V) 200 - 240 Fréquence (Hz) 50 / 60 bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 13 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.
FRANÇAIS 71
117885750-A-402016 www.aeg.