FSE73600P DE IT USER MANUAL Benutzerinformation Geschirrspüler Istruzioni per l’uso Lavastoviglie 2 27
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................5 3. GERÄTEBESCHREIBUNG........................................................................................... 6 4. BEDIENFELD................................................................................................................7 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com Bauernhöfe, Personalküchenbereiche in Geschäften, Büros und anderen Arbeitsumfeldern. – Für Gäste in Hotels, Motels, Pensionen und anderen wohnungsähnlichen Räumlichkeiten. Nehmen Sie keine technischen Änderungen am Gerät vor. Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt.
DEUTSCH 5 2. SICHERHEITSANWEISUNGEN 2.1 Montage WARNUNG! Die Montage des Geräts darf nur von einer qualifizierten Fachkraft durchgeführt werden. • Entfernen Sie das gesamte Verpackungsmaterial. • Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. • Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann, und benutzen Sie das Gerät nicht, wenn die Temperatur unter 0 °C absinkt. • Halten Sie sich an die mitgelieferte Montageanleitung.
www.aeg.com solche nicht in die Nähe oder auf das Gerät. des Wasserzulaufschlauchs an den autorisierten Kundendienst. 2.4 Gebrauch 2.5 Service • Setzen oder stellen Sie sich niemals auf die geöffnete Gerätetür. • Geschirrspüler-Reinigungsmittel sind gefährlich. Beachten Sie die Sicherheitsanweisungen auf der Reinigungsmittelverpackung. • Trinken Sie nicht das Wasser aus dem Gerät und verwenden Sie es nicht zum Spielen. • Nehmen Sie kein Geschirr aus dem Gerät, bevor das Programm beendet ist.
DEUTSCH 9 Reinigungsmittelbehälter 10 Besteckkorb 11 Unterkorb 12 Oberkorb 3.1 Beam-on-Floor Nach dem Abschalten des Gerätes erlischt der Beamon-Floor. Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Boden projiziert wird. Wird AirDry während der Trockenphase eingeschaltet, ist die Projektion auf dem Boden möglicherweise nicht vollständig sichtbar. Sie können dann auf dem Bedienfeld sehen, ob das Programm beendet wurde.
www.aeg.com 5.
DEUTSCH Programm P7 7) Verschmutzungsgrad Beladung Programmphasen Optionen • Normaler Verschmutzungsgrad • Geschirr und Besteck • • • • • XtraDry Vorspülen Hauptspülgang 50 °C Spülen Trocknen 1) Dieses Programm gewährleistet den wirtschaftlichsten Wasser- und Energieverbrauch für normal verschmutztes Geschirr und Besteck. Dies ist das Standardprogramm für Prüfinstitute. 2) Das Gerät erkennt den Verschmutzungsgrad und die Anzahl der Geschirrteile in den Körben.
www.aeg.com Programm1) Wasserverbrauch (l) Energieverbrauch (kWh) Dauer (Min.) 12 - 13 1.1 - 1.3 230 - 250 P7 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Informationen für Prüfinstitute Wenn Sie Informationen zur Durchführung von Leistungsprüfungen (z.B.
DEUTSCH über die Wasserhärte in Ihrem Gebiet informieren. Der Wasserenthärter muss unbedingt auf die richtige Stufe 11 eingestellt werden, um gute Spülergebnisse zu garantieren. Wasserhärte Deutsche Wasserhärtegrade (°dH) Französische Wasserhärtegrade (°fH) mmol/l Clarke Was- Einstellung für den serhärtegra- Wasserenthärter de 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.
www.aeg.com Klarspülmittelnachfüllanzeige ausschalten. Für eine bessere Trocknungsleistung empfehlen wir jedoch stets Klarspülmittel zu verwenden. Verwenden Sie die üblichen Reinigungsmittel oder MultiReinigungstabletten ohne Klarspülmittel, schalten Sie die Klarspülmittelnachfüllanzeige ein. Ausschalten der Klarspülmittelnachfüllanzeige Stellen Sie sicher, dass sich das Gerät im Benutzermodus befindet. 1. Drücken Sie . • Die Kontrolllampen und , , erlöschen.
DEUTSCH 6.6 AirDry AirDry wird bei allen Programmen mit AirDry verbessert die Trockenergebnisse bei einem geringeren Energieverbrauch. Ausnahme von (falls vorhanden) automatisch eingeschaltet. 13 Zur Verbesserung der Trocknungsleistung beachten Sie die XtraDry-Option oder schalten Sie AirDry ein. VORSICHT! Haben Kinder Zugang zum Gerät, wird empfohlen AirDry auszuschalten, da das Öffnen der Tür eine Gefahr darstellen könnte.
www.aeg.com Ist die Option nicht mit einem Programm kombinierbar, leuchtet die entsprechende Kontrolllampe nicht oder sie blinkt ein paar Sekunden schnell und erlischt dann. Die eingeschalteten Optionen können sich auf den Wasser- und Energieverbrauch sowie die Programmdauer auswirken. 7.1 XtraDry Schalten Sie diese Option ein, um die Trocknungsleistung zu erhöhen. 7.2 TimeSaver Mit dem TimeSaver können Sie die Dauer des gewählten Programms um etwa 50 % verkürzen.
DEUTSCH 15 Wenn Sie ein Programm starten, kann es bis zu 5 Minuten dauern das Filterharz des Wasserenthärters zu regenerieren. Das Gerät scheint nicht zu arbeiten. Die Spülphase startet erst nach Abschluss dieses Vorgangs. Dieser Vorgang wird regelmäßig wiederholt. 8.1 Salzbehälter VORSICHT! Verwenden Sie ausschließlich speziell für Geschirrspüler bestimmtes grobkörniges Salz. Mit feinem Salz besteht erhöhte Korrosionsgefahr.
www.aeg.com Füllen Sie den Klarspülmittel-Dosierer, wenn das Schauglas (A) klar ist. 9. TÄGLICHER GEBRAUCH 1. Öffnen Sie den Wasserhahn. 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. • Füllen Sie den Salzbehälter auf, wenn die Kontrolllampe Salz leuchtet. • Leuchtet die Kontrolllampe Klarspülmittel, füllen Sie den Klarspülmittel-Dosierer. 3. Beladen Sie die Körbe. 4. Füllen Sie Reinigungsmittel ein. 5.
DEUTSCH Öffnen der Tür während eines laufenden Programms Wenn Sie die Tür während eines laufenden Programms öffnen, stoppt das Gerät. Dies kann sich auf den Energieverbrauch und die Programmdauer auswirken. Wenn Sie die Tür wieder schließen, setzt das Gerät den Betrieb ab dem Zeitpunkt der Unterbrechung fort. Wird die Tür länger als 30 Sekunden während der Trockenphase geöffnet, wird das laufende Programm beendet. Dies geschieht nicht, wenn die Tür durch die Funktion AirDry geöffnet wird.
www.aeg.com Wasserverbrauch für Geschirr und Besteck mit normaler Verschmutzung. 10.2 Gebrauch von Salz, Klarspül- und Reinigungsmittel • Verwenden Sie nur Salz, Klarspülmittel und Reinigungsmittel für Geschirrspüler. Andere Produkte können das Gerät beschädigen. • Wir empfehlen in Bereichen mit hartem und sehr hartem Wasser Reinigungsmittel ohne Zusätze (Pulver, Gel oder Tabs ohne Zusätze), Klarspülmittel und Salz getrennt zu verwenden, um optimale Reinigungsund Trocknungsergebnisse zu erzielen.
DEUTSCH 10.6 Entladen der Körbe 1. Lassen Sie das Geschirr abkühlen, bevor Sie es aus dem Gerät nehmen. Heißes Geschirr ist stoßempfindlich. 2. Entladen Sie zuerst den Unter- und dann den Oberkorb. 19 Am Programmende kann sich noch Wasser an den Seitenwänden und der Gerätetür befinden. 11. REINIGUNG UND PFLEGE WARNUNG! Schalten Sie das Gerät immer aus und ziehen Sie den Netzstecker aus der Steckdose, bevor Reinigungsarbeiten durchgeführt werden.
www.aeg.com 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein. Stellen Sie sicher, dass er korrekt unter den beiden Führungen eingesetzt wurde. 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet.
DEUTSCH 11.3 Reinigen der Außenseiten • Reinigen Sie das Gerät mit einem weichen, feuchten Tuch. • Verwenden Sie ausschließlich Neutralreiniger. • Benutzen Sie keine Scheuermittel, scheuernde Reinigungsschwämmchen oder Lösungsmittel. 21 • Verwenden Sie einmal im Monat ein spezielles Reinigungsmittel für Geschirrspüler, um die Leistungsfähigkeit des Geräts zu erhalten. Befolgen Sie sorgfältig die Anweisungen auf der Reinigungsmittelverpackung.
www.aeg.com Störung und Alarmcode Mögliche Ursache und Abhilfe Das Programm startet nicht. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie diese ab, oder warten Sie, bis sie abgelaufen ist. • Das Gerät regeneriert das Harz im Wasserenthärter. Dieser Vorgang dauert ca. 5 Minuten. Es läuft kein Wasser in das Gerät. • Stellen Sie sicher, dass der Wasserzulaufhahn geöffnet ist.
DEUTSCH 23 Störung und Alarmcode Mögliche Ursache und Abhilfe Die Gerätetür ist schwer zu schließen. • Das Gerät ist nicht ausgerichtet. Schrauben Sie die Schraubfüße weiter hinein oder weiter heraus (falls vorhanden). • Teile des Geschirrs ragen aus den Körben heraus. Klappernde oder schlagende Geräusche aus dem Geräteinneren. • Das Geschirr ist nicht richtig in den Körben eingeordnet. Siehe Broschüre zum Beladen der Körbe. • Achten Sie darauf, dass sich die Sprüharme frei drehen können.
www.aeg.com Störung Mögliche Ursache und Abhilfe Nicht zufriedenstellende Trocknungsergebnisse. • Das Geschirr stand zu lange im geschlossenen Gerät. • Es ist kein Klarspülmittel vorhanden oder die Klarspülmittelmenge ist nicht ausreichend. Stellen Sie den Klarspülmittel-Dosierer auf eine höhere Einstellung. • Kunststoffteile müssen eventuell mit einem Tuch abgetrocknet werden. • Schalten Sie die Option XtraDry ein, und stellen Sie AirDry ein, um die beste Trocknungsleistung zu erzielen.
DEUTSCH 25 Störung Mögliche Ursache und Abhilfe Am Ende des Programms befinden sich Reinigungsmittelreste im Behälter. • Das Reinigungsmittel-Tab blieb im Behälter stecken und wurde daher nicht vollständig vom Wasser mitgenommen. • Das Wasser kann das Reinigungsmittel nicht aus dem Behälter ausspülen. Achten Sie darauf, dass der Sprüharm nicht blockiert oder verstopft ist. • Stellen Sie sicher, dass die im Korb eingeordneten Gegenstände ein Öffnen des Reinigungsmittelbehälters nicht verhindern.
www.aeg.com Wasserdruck bar (Mindest- und Höchstwert) 0.5 - 8 MPa (Mindest- und Höchstwert) 0.05 - 0.8 Wasserzufuhr Kalt- oder Warmwasser 2) max. 60 °C Fassungsvermögen Maßgedecke 13 Leistungsaufnahme Im eingeschalteten Zustand (W) 5.0 Im ausgeschalteten Zustand (W) 0.10 1) Weitere Angaben finden Sie auf dem Typenschild. 2) Wenn Sie Heißwasser mit umweltfreundlichen, alternativen Energiequellen (z. B.
ITALIANO 27 INDICE 1. INFORMAZIONI DI SICUREZZA...............................................................................28 2. ISTRUZIONI DI SICUREZZA...................................................................................... 30 3. DESCRIZIONE DEL PRODOTTO............................................................................. 31 4. PANNELLO COMANDI.............................................................................................32 5. PROGRAMMI..............................
1. www.aeg.com INFORMAZIONI DI SICUREZZA Leggere attentamente le istruzioni fornite prima di installare e utilizzare l'apparecchiatura. I produttori non sono responsabili di eventuali lesioni o danni derivanti da un'installazione o un uso scorretti. Conservare sempre le istruzioni in un luogo sicuro e accessibile per poterle consultare in futuro. 1.
ITALIANO clienti di hotel, motel, bed and breakfast e altri ambienti residenziali. Non modificare le specifiche tecniche dell'apparecchiatura. La pressione di esercizio dell'acqua (minima e massima) deve essere compresa tra 0.5 (0.05) / 8 (0.8) bar (MPa) Rispettare il numero massimo di 13 coperti. Se il cavo di alimentazione è danneggiato, deve essere sostituito dal produttore, dal Centro di Assistenza Autorizzato o da una persona qualificata per evitare situazioni di pericolo.
www.aeg.com 2. ISTRUZIONI DI SICUREZZA 2.1 Installazione AVVERTENZA! L’installazione dell'apparecchiatura deve essere eseguita da personale qualificato. • Rimuovere tutti i materiali di imballaggio. • Non installare o utilizzare l'apparecchiatura se è danneggiata. • Non collocare o usare l’apparecchiatura in un luogo in cui la temperatura possa scendere al di sotto di 0°C. • Attenersi alle istruzioni fornite insieme all'apparecchiatura.
ITALIANO • I detersivi per la lavastoviglie sono pericolosi. Osservare le istruzioni di sicurezza riportate sulla confezione del detersivo. • Non bere o giocare con l’acqua all’interno dell’apparecchiatura. • Non rimuovere i piatti dall'apparecchiatura fino al completamento del programma. Potrebbe rimanere del detergente sui piatti. • L'apparecchiatura può rilasciare vapore caldo se si apre la porta durante lo svolgimento del programma.
www.aeg.com 7 8 9 10 Apertura di ventilazione Contenitore del brillantante Erogatore del detersivo Cestello per le posate 11 Cestello inferiore 12 Cestello superiore 3.1 Beam-on-Floor Quando viene attivato AirDry durante la fase di asciugatura, la proiezione sul pavimento potrebbe non essere completamente visibile. Per vedere se il ciclo si è concluso, controllare il pannello di controllo. Il Beam-on-Floor è un fascio di luce mostrato sul pavimento al di sotto della porta dell'apparecchiatura.
ITALIANO 5.
www.aeg.com Programma Grado di sporco Tipo di carico Fasi del programma Opzioni P7 • Grado di sporco normale • Stoviglie e posate • • • • • XtraDry 7) Pre-lavaggio Lavaggio a 50 °C Risciacqui Asciugatura 1) Questo programma offre l'utilizzo più efficiente di acqua ed elettricità per lavare stoviglie e posate con grado di sporco normale. Questo è il programma standard per gli istituti di prova. 2) L'apparecchiatura rileva il grado di sporco e la quantità di stoviglie presenti nei cestelli.
ITALIANO 5.2 Informazioni per gli istituti di prova Per ricevere le informazioni necessarie per eseguire i test prestazionali (ad esempio conformemente a EN60436), inviare un'e-mail a: info.test@dishwasher-production.com 35 Nella vostra richiesta inserire il codice numero prodotto (PNC) indicato sulla targhetta. Per altre domande relativamente alla lavastoviglie invitiamo a consultare il manuale fornito in dotazione con l'apparecchiatura. 6. IMPOSTAZIONI 6.
www.aeg.com Gradi tedeschi (°dH) Gradi francesi (°fH) mmol/l Gradi Clarke Livello del decalcificatore dell’acqua 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Impostazioni di fabbrica.
ITALIANO • Le spie spente. , , e sono • La spia lampeggia ancora. • Il display mostra l'impostazione attuale. – = la notifica contenitore del brillantante vuoto è disattivata. – = la notifica contenitore del brillantante vuoto è attivata. per cambiare 2. Premere l'impostazione. 3. Premere On/Off per confermare l'impostazione. 6.4 Livello di brillantante Sarà possibile impostare la quantità di brillantante rilasciata tra il livello 1 (quantità minima) e il livello 6 (quantità massima).
www.aeg.com Durante la fase di asciugatura l'oblò si apre automaticamente e rimane socchiuso. ATTENZIONE! Non cercare di chiudere l'apparecchiatura 2 minuti dopo l'apertura automatica. Ciò potrebbe danneggiare l'apparecchio. Qualora successivamente la porta venga chiusa per altri 3 minuti, si conclude la modalità in funzione. AirDry viene attivata automaticamente con tutti i programmi, escluso applicabile). (se Come disattivare l'opzione AirDry Verificare che l'apparecchiatura sia in modalità utente.
ITALIANO successivi. Questa configurazione può essere modificata in qualsiasi momento. Ogni volta che viene attivato , XtraDry l'opzione è spenta e deve essere scelta manualmente. L'attivazione dell'opzione XtraDry disattiva TimeSaver e viceversa. Come attivare XtraDry Premere . La spia relativa è accesa. Il display indica la durata aggiornata del programma. 7.2 TimeSaver TimeSaver consente di ridurre la durata di un programma selezionato indicativamente del 50%.
www.aeg.com 1. Ruotare il tappo del contenitore del sale in senso antiorario e aprirlo. 2. Versare 1 litro d’acqua nel contenitore del sale (solo la prima volta). 3. Riempire il contenitore di sale con sale per lavastoviglie (fino a che non sarà pieno). 8.2 Come riempire il contenitore del brillantante A B C 4. Scuotere con delicatezza l'imbuto per la maniglia per far scendere anche gli ultimi granuli. 5. Togliere l'eventuale sale rimasto attorno all'apertura del contenitore. 6.
ITALIANO 5. Impostare ed avviare il programma corretto per il tipo di carico ed il grado di sporco. 9.1 Utilizzo del detersivo A B 41 5. Chiudere la porta dell'apparecchiatura per avviare il programma. Avvio del programma con partenza ritardata 1. Impostare un programma. 2. Premere ripetutamente finché il display indica l'intervallo desiderato per la partenza ritardata (da 1 a 24 ore). C ATTENZIONE! Utilizzare solo detersivo specifico per lavastoviglie. 1.
www.aeg.com Annullamento del programma Tenere premuto Reset finché l’apparecchiatura entra in modalità di selezione programma. Verificare che vi sia del detersivo nell'apposito contenitore prima di avviare un nuovo programma. Termine del programma Una volta terminato il programma, il display mostra 0:00 e si accende la spia . Tutti i tasti sono inattivi ad eccezione del tasto On/Off. Se si apre la porta prima di attivare il tasto Auto Off, l'apparecchiatura si spegne automaticamente. 2.
ITALIANO 10.3 Cosa fare se non si desidera utilizzare più il detersivo in pastiglie multifunzione Prima di iniziare ad usare separatamente detersivo, sale e brillantante attenersi alla procedura seguente: 1. Impostare il livello più alto del decalcificatore dell'acqua. 2. Assicurarsi che i contenitori del sale e del brillantante siano pieni. 3. Avviare il programma più breve con una fase di risciacquo. Non aggiungere il detersivo e non caricare i cestelli. 4.
www.aeg.com 11.1 Pulizia dei filtri Il sistema del filtro si compone di 3 parti. C B A 1. Ruotare il filtro (B) in senso antiorario e rimuoverlo. 2. Estrarre il filtro (C) dal filtro (B). 3. Rimuovere il filtro piatto (A). 4. Lavare i filtri. 5. Assicurarsi che non vi siano residui di cibo o di sporco all'interno o attorno al bordo della vasca di raccolta. 6. Posizionare nuovamente il filtro piatto (A). Assicurarsi che sia posizionato correttamente al di sotto delle due guide. 7.
ITALIANO ATTENZIONE! Un’errata posizione dei filtri può comportare scadenti risultati di lavaggio e danni all’apparecchiatura. 45 4. Per riagganciare il mulinello al cestello, premerlo nella direzione indicata dalla freccia inferiore e contemporaneamente ruotarlo in senso antiorario finché non si blocca in posizione. 11.2 Pulizia del mulinello superiore Si consiglia di pulire regolarmente il mulinello superiore per evitare che lo sporco ostruisca i fori.
www.aeg.com 12. RISOLUZIONE DEI PROBLEMI AVVERTENZA! Una riparazione scorretta dell'apparecchiatura potrebbe presentare dei pericoli per la sicurezza dell'utente. Qualsiasi tipo di riparazione deve essere eseguita da personale qualificato. La maggior parte dei possibili problemi possono essere risolti senza il bisogno di contattare il Centro di Assistenza Autorizzato. Rimandiamo alla tabella qui di seguito per informazioni sui possibili problemi. In alcuni casi il display visualizza un codice allarme.
ITALIANO 47 Problema e codice allarme Possibile causa e soluzione Il programma dura troppo. • Se è stata impostata l'opzione di Partenza ritardata, annullare l'impostazione o attendere il termine del conto alla rovescia. • Attivare l'opzione TimeSaver per ridurre la durata del programma. • L'attivazione delle opzioni può aumentare la durata del programma. Il tempo residuo sul display aumenta e raggiunge quasi il termine della durata del programma. • Non si tratta di un'anomalia.
www.aeg.com 12.1 I risultati di lavaggio e di asciugatura non sono soddisfacenti Problema Possibile causa e soluzione Risultati di lavaggio insoddisfacenti. • Fare riferimento a "Utilizzo quotidiano", "Consigli e suggerimenti" e al libretto contenente le indicazioni per caricare il cestello. • Usare programmi di lavaggio più intensi. • Pulire i mulinelli ed il filtro. Vedere il capitolo "Pulizia e cura". Risultati di asciugatura insoddisfacenti.
ITALIANO Problema 49 Possibile causa e soluzione Tracce di ruggine sulle posate. • È presente troppo sale nell'acqua utilizzata per il lavaggio. Fare riferimento a "Decalcificatore dell'acqua". • Sono state sistemate insieme posate d'argento e acciaio inossidabile. Evitare di sistemare oggetti d'argento e acciaio inossidabile uno accanto all'altro.
www.aeg.com 13. DATI TECNICI Dimensioni Larghezza / altezza / profondità (mm) 596 / 818 - 898 / 550 Collegamento elettrico 1) Tensione (V) 200 - 240 Frequenza (Hz) 50 / 60 Pressione dell’acqua di alimentazione bar (minima e massima) 0.5 - 8 MPa (minimo e massimo) 0.05 - 0.8 Collegamento dell'acqua Acqua fredda o calda 2) max. 60°C Capacità Coperti 13 Consumo di energia Modalità Acceso (W) 5.0 Modalità Off (W) 0.10 1) Fare riferimento alla targhetta dei dati per gli altri valori.
ITALIANO 51
117886142-A-092018 www.aeg.