FSE83600P USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. If the appliance has ventilation openings in the base, they must not be covered e.g. by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets.
ENGLISH 5 2.5 Internal light WARNING! Risk of injury. WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Top spray arm Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 TimeBeam The TimeBeam is a display that is shown on the floor below the appliance door. • When the programme starts, the programme duration comes on. • When the programme is completed, 0:00 and CLEAN come on. • When the delay start starts, the countdown duration and DELAY come on.
ENGLISH When AirDry is activated during the drying phase, the projection on the floor may not be completely visible. To check the remaining time of the running programme, look at the control panel display. 4. CONTROL PANEL 1 1 2 3 4 5 2 On/off button Display Delay button Program button ExtraHygiene button 3 4 6 7 8 9 5 6 7 8 9 TimeSaver button XtraDry button Reset button Indicators 4.1 Indicators Indicator Description End indicator. Rinse aid indicator.
www.aeg.
ENGLISH 9 5.1 Consumption values Water (l) Energy (kWh) Duration (min) P1 10.5 0.832 232 P2 7 - 14 0.6 - 1.6 40 - 170 P5 14 - 16 1.2 - 1.5 160 - 180 P3 12.5-14.5 1.4-1.7 170-190 P6 12 - 14 0.7 - 0.9 82-92 P4 10 0.9 30 P8 4 0.1 14 P7 9 - 10 1.1 - 1.3 230 - 250 Programme 1) 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.
www.aeg.com How to set the programme selection mode a detrimental effect on the washing results and on the appliance. The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. The appliance is in programme selection mode when the display shows the programme number P1. The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area.
ENGLISH and start to flash and the display is blank. 2. Press . • The indicators and , , , go off. • The indicator continues to flash. • The display shows the current setting: e.g. = level 5. again and again to change 3. Press the setting. 4. Press the on/off button to confirm the setting. 6.3 The rinse aid dispenser The rinse aid helps to dry the dishes without streaks and stains. The rinse aid is automatically released during the hot rinse phase.
www.aeg.com 6.5 Acoustic signals Acoustic signals sound when a malfunction of the appliance occurs. It is not possible to deactivate these acoustic signals. There is also an acoustic signal that sounds when the programme is completed. By default this acoustic signal is deactivated but it is possible to activate it. How to activate the acoustic signal for the end of programme The appliance must be in programme selection mode. 1.
ENGLISH the indicators CAUTION! In case of presence of children, the AirDry system can be deactivated if you want to keep the door closed in the end of the cycle. , , , 13 , and start to flash and the display is blank. 2. Press . • The indicators and AirDry is automatically activated with all programmes excluding To improve the drying performance refer to the XtraDry option or activate AirDry. How to deactivate AirDry The appliance must be in programme selection mode. , , , go off.
www.aeg.com This option increases the pressure and the temperature of the water. The washing and the drying phases are shorter. By default, TimeSaver is off, but it is possible to activate it manually. This option cannot be combined with XtraDry at the same time. How to activate TimeSaver Press , the related indicator comes on. If the option is not applicable to the programme, the related indicator does not come on or it flashes quickly for a few seconds and then goes off.
ENGLISH CAUTION! Water and salt can come out of the salt container when you fill it. After you fill the salt container, immediately start a programme to prevent corrosion. 8.2 How to fill the rinse aid dispenser A B CAUTION! Only use rinse aid specifically designed for dishwashers. 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid.
www.aeg.com 1. Press the release button (A) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (B). 3. If the programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance door. 4. Close the lid. Make sure that the lid locks into position. 9.2 Setting and starting a programme The Auto Off function This function decreases energy consumption by deactivating automatically the appliance when it is not operating.
ENGLISH End of programme 17 Close the water tap. When the programme is completed and you open the door, the appliance is automatically deactivated. 10. HINTS AND TIPS 10.1 General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase.
www.aeg.com • Put hollow items (cups, glasses and pans) with the opening down. • Make sure that glasses do not touch other glasses. • Put cutlery and small items in the cutlery basket. • Put light items in the upper basket. Make sure that the items do not move. • Make sure that the spray arms can move freely before you start a programme. 10.5 Before starting a programme Make sure that: • There is dishwasher salt and rinse aid (unless you use multi- tablets).
ENGLISH 19 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 4. Wash the filters. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. Clogged holes can cause unsatisfactory washing results. 5.
www.aeg.com 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 11.4 Internal cleaning 4. To engage again the spray arm to the basket, press the spray arm upwards in the direction indicated by the lower arrow and simultaneously turn it counterclockwise until it locks into place. • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth.
ENGLISH 21 Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The program does not start. • Make sure that the appliance door is closed. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to recharge the resin inside the water softener.
www.aeg.com Problem and alarm code Possible cause and solution Rattling/knocking sounds from inside the appliance. • The tableware is not properly arranged in the baskets. Refer to basket loading leaflet. • Make sure that the spray arms can rotate freely. The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use.
ENGLISH 23 Problem Possible cause and solution The dishes are wet. • For the best drying performance activate the option XtraDry and set AirDry . • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together.
www.aeg.com Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. 13. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818-898 / 550 Electrical connection 1) Voltage (V) 220 - 240 Frequency (Hz) 50 bar (minimum and maximum) 0.5 - 8 MPa (minimum and maximum) 0.05 - 0.8 Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 5.0 Power consumption Off-mode (W) 0.
X X X Hydraulic circuit (including tanks)* Wiring harnesses Hg Cd Cr6+ Hazardous substances PBBs PBDEs Note: 1. This table is compiled according to SJ/T11364-2014. 2. means that this kind of hazardous substance content in all of the homogenous materials of this part is under the limitations regulated in GB/T26572-2011. 3. X means that this kind of hazardous substance content in at least one homogenous material of this part exceeds the limitations regulated in GB/T26572-2011. 4.
www.aeg.
ENGLISH 27
117876210-A-492017 www.aeg.
