FSE83600P USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
ENGLISH • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. • UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Top spray arm Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 TimeBeam TimeBeam displays the following information on the floor below the appliance door: • The programme duration when the programme begins. • 0:00 and CLEAN when the programme is completed. • DELAY and the countdown duration when the delay start begins. • An alarm code when the appliance has a malfunction.
ENGLISH When AirDry is activated during the drying phase, the projection on the floor may not be completely visible. To check the remaining time of the running programme, look at the control panel display. 4. CONTROL PANEL 1 1 2 3 4 5 3 2 On/off button Display Delay button Program button ExtraHygiene button 4 6 7 8 9 5 6 7 8 9 TimeSaver button XtraDry button Reset button Indicators 4.1 Indicators Indicator Description Salt indicator. It is on when the salt container needs refilling.
www.aeg.
ENGLISH 9 5.1 Consumption values Water (l) Energy (kWh) Duration (min) P1 10.5 0.832 240 P2 8 - 15 0.7 - 1.7 46 - 170 P5 14 - 16 1.2 - 1.5 160 - 180 P3 12.5 - 14.5 1.4 - 1.7 170 - 190 P6 12 - 14 0.8 - 1.0 82 - 92 P4 10 0.9 30 P8 4 0.1 14 P7 12 - 13 1.1 - 1.3 230 - 250 Programme 1) 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.
www.aeg.com How to set the programme selection mode indicators The appliance is in programme selection mode when the display shows the programme number P1. 6.2 The water softener After activation, the appliance is in programme selection mode by default. If not, set the programme selection mode the following way: Press and hold Reset until the appliance is in programme selection mode. How to enter user mode Make sure the appliance is in programme selection mode.
ENGLISH • The indicator still flashes. • The display shows the current setting: e.g. = level 5. 2. Press repeatedly to change the setting. 3. Press on/off to confirm the setting. 6.3 The rinse aid empty notification When the rinse aid chamber is empty, the rinse aid indicator is turned on notifying to refill rinse aid. If the drying results are satisfactory while using multitablets only, it is possible to deactivate the notification for refilling rinse aid.
www.aeg.com 6.6 How to set the colour of the TimeBeam It is possible to change the colour of the TimeBeam to match the colour of the kitchen floor. There are several colours available. The TimeBeam can also be deactivated. Make sure the appliance is in user mode. 1. Press . • The indicators and , , , are off. • The indicator still flashes. • The display shows a number and letter C. Each number refers to a different colour. – = TimeBeam deactivated. repeatedly to change the 2. Press colour. 3.
ENGLISH 13 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you select non compatible options, the appliance automatically deactivates one or more of them. Only the indicators of the still active options are on.
www.aeg.com 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets. After starting a programme, it may take up to 5 minutes for the appliance to recharge the resin in the water softener. It seems that the appliance is not working. The washing phase starts only after this procedure is completed. The procedure is repeated periodically. 8.
ENGLISH 15 Fill the rinse aid dispenser when the indicator (A) is clear. 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil. 9.1 Using the detergent A B 9.
www.aeg.com If the door is opened for more than 30 seconds during the drying phase, the running programme ends. It does not happen if the door is opened by AirDry function. Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again. Press and hold Reset until the appliance is in programme selection mode. Cancelling the programme Press and hold Reset until the appliance is in programme selection mode.
ENGLISH agents), rinse aid and salt separately for optimal cleaning and drying results. • At least once a month run the appliance with the use of appliance cleaner which is particularly suitable for this purpose. • Detergent tablets do not fully dissolve with short programmes. To prevent detergent residues on the tableware, we recommend that you use the tablets with long programmes. • Do not use more than the correct quantity of detergent. Refer to the instructions on the detergent packaging. 10.
www.aeg.com 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. 3. Remove the flat filter (A). 4. Wash the filters. 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6.
ENGLISH CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the upper spray arm 19 4. To engage again the spray arm to the basket, press the spray arm upwards in the direction indicated by the lower arrow and simultaneously turn it counterclockwise until it locks into place. We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. Clogged holes can cause unsatisfactory washing results. 1.
www.aeg.com • Using short-duration programmes regularly can cause grease and limescale buildup inside the appliance. Run long-duration programmes at least twice a month to prevent the buildup. 12. TROUBLESHOOTING WARNING! Improper repair of the appliance may pose a danger to the safety of the user. Any repairs must be performed by qualified personnel. to contact an Authorised Service Centre. Refer to the below table for information on possible problems.
ENGLISH 21 Problem and alarm code Possible cause and solution The programme lasts too long. • If the delay start option is set, cancel the delay setting or wait for the end of the countdown. • Activate the TimeSaver option to reduce the programme duration. • Activating options can increase the programme duration. The remaining time in the display increases and skips nearly to the end of the programme duration. • This is not a defect. The appliance is working correctly.
www.aeg.com Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option XtraDry and set AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets.
ENGLISH 23 Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. • For washing delicate items and glassware, select the dedicated programme. Refer to "Programmes".
www.aeg.com 14. ENVIRONMENTAL CONCERNS Recycle materials with the symbol . Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose of appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
X X X Hydraulic circuit (including tanks)* Wiring harnesses * Hg Cd Cr6+ Hazardous substances PBBs PBDEs Note: 1. This table is compiled according to SJ/T11364-2014. means that this kind of hazardous substance content in all of the homogenous materials of this part is under the limitations 2. regulated in GB/T26572-2011. 3. X means that this kind of hazardous substance content in at least one homogenous material of this part exceeds the limitations regulated in GB/T26572-2011. 4.
www.aeg.
ENGLISH 27
117876211-A-082018 www.aeg.