FSK52610Z USER MANUAL DE Benutzerinformation Geschirrspüler
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................5 3. PRODUKTBESCHREIBUNG........................................................................................ 6 4. BEDIENFELD................................................................................................................7 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Bedienungsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung zum Nachschlagen an einem sicheren und zugänglichen Ort auf. 1.
www.aeg.com Bauernhöfe, Personalküchenbereiche in Geschäften, Büros und anderen Arbeitsumfeldern. – Für Gäste in Hotels, Motels, Pensionen und anderen wohnungsähnlichen Räumlichkeiten. Nehmen Sie keine technischen Änderungen am Gerät vor. Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt.
DEUTSCH 5 2. SICHERHEITSANWEISUNGEN 2.1 Montage WARNUNG! Die Montage des Geräts darf nur von einer qualifizierten Fachkraft durchgeführt werden. • Entfernen Sie das gesamte Verpackungsmaterial. • Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. • Verwenden Sie das Gerät aus Sicherheitsgründen nicht, bevor es in den Einbauschrank gesetzt wird. • Halten Sie sich an die mitgelieferte Montageanleitung. • Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist.
www.aeg.com • Es kann heißer Dampf aus dem Gerät austreten, wenn Sie die Tür während des Ablaufs eines Programms öffnen. Wasserzulaufschlauch beschädigt ist. Wenden Sie sich für den Austausch des Wasserzulaufschlauchs an den autorisierten Kundendienst. 2.5 Service 2.4 Gebrauch • Wenden Sie sich zur Reparatur des Geräts an den autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile.
DEUTSCH 7 Klarspülmittel-Dosierer 8 Reinigungsmittelfach 9 Besteckkorb 10 Unterkorb 11 Oberkorb 3.1 Beam-on-Floor Nach dem Abschalten des Gerätes erlischt der Beamon-Floor. Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Boden projiziert wird. Wird AirDry während der Trockenphase eingeschaltet, ist die Projektion auf dem Boden möglicherweise nicht vollständig sichtbar. Sie können dann auf dem Bedienfeld sehen, ob das Programm beendet wurde.
www.aeg.
DEUTSCH Wasserverbrauch (l) Energieverbrauch (kWh) Dauer (min.) P2 6 - 12 0.6 - 1.5 44 - 160 P3 14 - 15 1.5 - 1.7 155 - 171 P4 10 0.8 30 P5 13 - 14 1.0 - 1.1 75 - 85 Programm1) 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Informationen für Prüfinstitute Wenn Sie Informationen zur Durchführung von Leistungsprüfungen (z.B.
www.aeg.com , und blinken und das Display nichts anzeigt. 6.2 Wasserenthärter über die Wasserhärte in Ihrem Gebiet informieren. Der Wasserenthärter muss unbedingt auf die richtige Stufe eingestellt werden, um gute Spülergebnisse zu garantieren. Der Wasserenthärter entfernt Mineralien aus dem Spülwasser, die sich nachteilig auf die Spülergebnisse und das Gerät auswirken könnten. Durch die Enthärtung von hartem Wasser erhöht sich der Wasser- und Energieverbrauch und verlängert sich die Programmdauer.
DEUTSCH • Die Kontrolllampe blinkt weiterhin. • Im Display wird die aktuelle = die Klarspülmittelnachfüllanzeige ist eingeschaltet (Werkseinstellung). Einstellung angezeigt: z. B. Stufe 5. = wiederholt zum 2. Drücken Sie Ändern der Einstellung. 3. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. 6.3 Klarspülmittelnachfüllanzeige Das Klarspülmittel ermöglicht das Trocknen des Geschirrs ohne Streifen und Flecken. Das Klarspülmittel wird automatisch während der heißen Spülphase abgegeben.
www.aeg.com XtraDry-Option oder schalten Sie AirDry ein. VORSICHT! Haben Kinder Zugang zum Gerät, wird empfohlen AirDry auszuschalten, da das Öffnen der Tür eine Gefahr darstellen könnte. So schalten Sie AirDry aus Während der Trockenphase wird die Tür automatisch geöffnet und bleibt einen Spaltbreit offen. VORSICHT! Versuchen Sie nicht, die Gerätetür innerhalb der ersten 2 Minuten nach der automatischen Öffnung zu schließen. Andernfalls kann das Gerät beschädigt werden.
DEUTSCH Ist die Option nicht mit einem Programm kombinierbar, leuchtet die entsprechende Kontrolllampe nicht oder sie blinkt ein paar Sekunden schnell und erlischt dann. Die eingeschalteten Optionen können sich auf den Wasser- und Energieverbrauch sowie die Programmdauer auswirken. 7.1 XtraDry Schalten Sie diese Option ein, um die Trocknungsleistung zu erhöhen. Ist XtraDry eingeschaltet, kann sich dies auf die Dauer einiger Programme, den Wasserverbrauch und die Temperatur des letzten Spülgangs auswirken.
www.aeg.com 8.1 Salzbehälter VORSICHT! Verwenden Sie ausschließlich speziell für Geschirrspüler bestimmtes grobkörniges Salz. Mit feinem Salz besteht erhöhte Korrosionsgefahr. Das Salz wird für die Regenerierung des Filterharzes im Wasserenthärter und zur Erzielung guter Spülergebnisse im täglichen Gebrauch benötigt. VORSICHT! Beim Befüllen des Salzbehälters können Wasser und Salz austreten. Starten Sie nach dem Füllen des Salzbehälters umgehend ein Programm, um Korrosion zu verhindern. 8.
DEUTSCH 4. Schließen Sie den Deckel. Achten Sie darauf, dass die Entriegelungstaste einrastet. 15 Sie können den Regler der Zugabemenge (B) zwischen Position 1 (geringste Menge) und Position 4 oder 6 (größte Menge) einstellen. 9. TÄGLICHER GEBRAUCH 1. Öffnen Sie den Wasserhahn. 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. • Füllen Sie den Salzbehälter auf, wenn die Kontrolllampe Salz leuchtet.
www.aeg.com 4. Stellen Sie die verfügbaren Optionen ein. 5. Schließen Sie die Gerätetür, um das Programm zu starten. Starten eines Programms mit Zeitvorwahl 1. Wählen Sie ein Programm. 2. Drücken Sie die Taste wiederholt, bis im Display die gewünschte Zeitvorwahl angezeigt wird (zwischen 1 und 24 Stunden). Die Kontrolllampe der Zeitvorwahl leuchtet auf. 3. Schließen Sie die Gerätetür, um den Countdown zu starten.
DEUTSCH • Spülen Sie das Geschirr nicht von Hand vor. Wählen Sie bei Bedarf ein Programm mit Vorspülphase. • Nutzen Sie die Körbe immer ganz aus. • Achten Sie darauf, dass das Geschirr in den Körben sich weder berührt noch von anderem Geschirr verdeckt wird. Nur so erreicht das Spülwasser das ganze Geschirr. • Sie können Geschirrspülreiniger, Klarspülmittel und Salz separat oder Kombi-Reinigungstabletten (z.B. „Allin-1“) verwenden. Beachten Sie die auf der Verpackung angegebenen Hinweise.
www.aeg.com 10.5 Vor dem Starten eines Programms Stellen Sie vor dem Start des Programms sicher, dass: • Die Siebe sauber und ordnungsgemäß eingesetzt sind. • Der Deckel des Salzbehälters fest geschlossen ist. • Die Sprüharme nicht verstopft sind. • Geschirrspülsalz und Klarspülmittel vorhanden sind (außer Sie verwenden Multi-Reinigungstabletten). • Die Geschirrteile richtig in den Körben angeordnet sind. • Das Programm sich für die Beladung und den Verschmutzungsgrad eignet.
DEUTSCH 19 VORSICHT! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 11.2 Reinigen der Sprüharme Bauen Sie die Sprüharme nicht aus. Falls die Löcher in den Sprüharmen verstopft sind, reinigen Sie sie mit einem dünnen spitzen Gegenstand. 11.3 Reinigen der Außenseiten 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein.
www.aeg.com 12. FEHLERSUCHE Wenn das Gerät nicht startet oder während des Betriebs stehen bleibt, prüfen Sie, ob Sie die Störung anhand der in der Tabelle enthaltenen Hinweise selbst beheben können, oder wenden Sie sich an einen autorisierten Kundendienst. Bei manchen Störungen zeigt das Display einen Alarmcode an. Die meisten Störungen, die auftreten, können behoben werden, ohne dass der autorisierte Kundendienst gerufen werden muss.
DEUTSCH 21 Störung und Alarmcode Mögliche Ursache und Abhilfe Das Wasserauslauf-Schutzsystem ist eingeschaltet. • Drehen Sie den Wasserhahn zu und wenden Sie sich an einen autorisierten Kundendienst. Im Display erscheint . Während des Betriebs • Das ist normal. So werden optimale Reinigungsergebstoppt und startet das Gerät nisse erzielt und Strom gespart. mehrmals. Das Programm dauert zu lang. • Wählen Sie die TimeSaver-Option, um die Programmdauer zu verkürzen.
www.aeg.com 12.1 Die Spül- und Trocknungsergebnisse sind nicht zufriedenstellend Störung Mögliche Ursache und Abhilfe Nicht zufriedenstellende Spülergebnisse. • Siehe „Täglicher Gebrauch“, „Tipps und Hinweise“ sowie die Broschüre zum Beladen der Körbe. • Nutzen Sie intensivere Spülprogramme. • Reinigen Sie die Austrittsdüsen der Sprüharme und das Sieb. Siehe „Reinigung und Pflege“. Nicht zufriedenstellende Trocknungsergebnisse. • Das Geschirr stand zu lange im geschlossenen Gerät.
DEUTSCH 23 Störung Mögliche Ursache und Abhilfe Rostspuren am Besteck. • Das Spülwasser enthält zu viel Salz. Siehe „Wasserenthärter“. • Silber- und Edelstahlbesteck wurden zusammen eingeordnet. Ordnen Sie nicht Silber- und Edelstahlbesteck zusammen ein. Am Ende des Programms befinden sich Reinigungsmittelreste im Behälter. • Das Reinigungsmittel-Tab blieb im Behälter stecken und wurde daher nicht vollständig vom Wasser mitgenommen.
www.aeg.com Modellkennung FSK52610Z 911536351 Nennleistung (Standard-Einstellungen) 13 Energieeffizienzklasse A++ Energieverbrauch in kWh pro Jahr, basierend auf 280 262 Stanard-Reinigungszyklen bei Verwendung von kaltem Wasser und der Modi mit wenig Energiebedarf. Der tatsächliche Verbrauch hängt davon ab, wie das Gerät verwendet wird. Energieverbrauch des Standard-Reinigungs-Zyklus in kWh 0.920 Energieverbrauch im OFF-Modus in W 0.50 Energieverbauch im nicht-ausgeschalteten Zustand in W 5.
DEUTSCH Wasserzufuhr Kalt- oder Warmwasser2) 25 max. 60 °C 1) Weitere Angaben finden Sie auf dem Typenschild. 2) Wenn Sie Heißwasser mit umweltfreundlichen, alternativen Energiequellen (z. B. Solaranlagen) aufbereiten, können Sie durch den Anschluss des Geräts an die Heißwasserversorgung Energie sparen. 15. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern.
www.aeg.
DEUTSCH 27
156918741-A-222019 www.aeg.