FSK63600P USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. If the appliance has ventilation openings in the base, they must not be covered e.g. by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets.
ENGLISH • Ensure that there are no visible water leaks during and after the first use of the appliance. • The water inlet hose has a safety valve and a sheath with an inner mains cable. • • • • 5 instructions on the detergent packaging. Do not drink and play with the water in the appliance. Do not remove the dishes from the appliance until the programme is complete. Some detergent may remain on the dishes. The appliance can release hot steam if you open the door while a programme operates.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Top spray arm Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 Beam-on-Floor The Beam-on-Floor is a light that is displayed on the floor below the appliance door. • When the programme starts, a red light comes on and stays on for the duration of the programme. • When the programme is completed, a green light comes on. • When the appliance has a malfunction, the red light flashes.
ENGLISH 4. CONTROL PANEL 2 1 1 2 3 4 5 On/off button Display Delay button Program button ExtraHygiene button 3 6 7 8 9 4 5 6 7 8 9 TimeSaver button XtraDry button Reset button Indicators 4.1 Indicators Indicator Description End indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. 5.
www.aeg.
ENGLISH 5.2 Information for test institutes 9 info.test@dishwasher-production.com For all the necessary information for test performance, send an email to: Write down the product number (PNC) that is on the rating plate. 6. SETTINGS 6.1 Programme selection mode and user mode not, set the programme selection mode the following way: Press and hold Reset until the appliance is in programme selection mode.
www.aeg.com German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level. Whether you use a standard detergent or multi-tabs (with or without salt), set the proper water hardness level to keep the salt refill indicator active.
ENGLISH 1. Press 11 . • The indicators are off. , , and continues to • The indicator flash. • The display shows the current = level 4. setting: e.g. – The levels of rinse aid range from 0A to 6A where level 0A means rinse aid is not used. 2. Press repeatedly to change the setting. 3. Press on/off to confirm the setting. 6.5 Acoustic signals Acoustic signals sound when a malfunction of the appliance occurs. It is not possible to deactivate these acoustic signals.
www.aeg.com 3. Press on/off to confirm the setting. 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you select non compatible options, the appliance automatically deactivates one or more of them. Only the indicators of the still active options are on. 7.1 XtraDry Activate this option to boost the drying performance.
ENGLISH 13 8. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets.
www.aeg.com 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) becomes clear. If you use multi-tablets and the drying performance is satisfactory, the rinse aid refill indication can be disabled. We recommend to always use rinse aid for better drying performance, also in combination with multitablets containing rinsing agent. 9. DAILY USE 1.
ENGLISH 15 Starting a programme with delay start Cancelling the delay start while the countdown operates 1. Set a programme. 2. Press Delay repeatedly until the display shows the desired delay time (from 1 to 24 hours). When you cancel the delay start you have to set the programme and options again. The indicator is on. 3. Close the appliance door to start the countdown. While a countdown is running it is possible to increase the delay time but not to change the selection of the programme and options.
www.aeg.com 10.2 Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance. • In areas with hard and very hard water we recommend to use plain dishwasher detergent (powder, gel, tablets containing no additional agents), rinse aid and salt separately for optimal cleaning and drying results. • At least once a month run the appliance with the use of appliance cleaner which is particularly suitable for this purpose.
ENGLISH 17 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. 3. Remove the flat filter (A). 4. Wash the filters. 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6.
www.aeg.com CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the upper spray arm 4. To engage again the spray arm to the basket, press the spray arm upwards in the direction indicated by the lower arrow and simultaneously turn it counterclockwise until it locks into place. We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. Clogged holes can cause unsatisfactory washing results. 1.
ENGLISH • Using short-duration programmes regularly can cause grease and limescale buildup inside the appliance. Run long-duration 19 programmes at least twice a month to prevent the buildup. 12. TROUBLESHOOTING If the appliance does not start or it stops during operation, first check if you can solve the problem by yourself with the help of the information in the table or contact an Authorised Service Centre. WARNING! Repairs not properly done may result in serious risk to the safety of the user.
www.aeg.com Problem and alarm code Possible cause and solution The appliance stops and • It is normal. It provides optimal cleaning results and enstarts more times during opergy savings. eration. The program lasts too long. • Select the TimeSaver option to shorten the program time. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown. The remaining time in the • This is not a defect. The appliance is working correctly.
ENGLISH 21 Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option XtraDry and set AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets.
www.aeg.com Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. The level of salt is low, check the refill indicator. The cap of the salt container is loose. Your tap water is hard.
ENGLISH 23 product to your local recycling facility or contact your municipal office. appliances marked with the symbol with the household waste.
117883281-A-392017 www.aeg.