FSK83700P USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
ENGLISH • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. • UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Top spray arm Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 TimeBeam TimeBeam displays the following information on the floor below the appliance door: • The programme duration when the programme begins. • 0:00 and CLEAN when the programme is completed. • DELAY and the countdown duration when the delay start begins. • An alarm code when the appliance has a malfunction.
ENGLISH When AirDry is activated during the drying phase, the projection on the floor may not be completely visible. To check the remaining time of the running programme, look at the control panel display. 4. CONTROL PANEL 1 1 2 3 4 5 3 2 On/off button Display Delay touch button Program touch button ExtraHygiene touch button 4 6 7 8 9 5 6 7 8 9 TimeSaver touch button XtraDry touch button RESET touch button Indicators 4.1 Indicators Indicator Description Salt indicator.
www.aeg.
ENGLISH 9 5.1 Consumption values Water (l) Energy (kWh) Duration (min) P1 11 0.857 235 P2 8 - 15 0.7 - 1.7 46 - 170 P5 14 - 16 1.2 - 1.5 160 - 180 P3 12.5 - 14.5 1.4 - 1.7 170 - 190 P6 12 - 14 0.8 - 1.0 82 - 92 P4 10 0.9 30 P8 4 0.1 14 P7 12 - 13 1.1 - 1.3 230 - 250 Programme 1) 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.
www.aeg.com As the appliance stores the saved settings, there is no need to configure it before every cycle. indicators How to set the programme selection mode 6.2 The water softener , , and The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. After activation, the appliance is in programme selection mode by default.
ENGLISH How to set the water softener level Make sure the appliance is in user mode. 1. Press . , • The indicators and , , are off. • The indicator still flashes. • The display shows the current setting: e.g. = level 5. 2. Press repeatedly to change the setting. 3. Press on/off to confirm the setting. When the rinse aid chamber is empty, the rinse aid indicator is turned on notifying to refill rinse aid.
www.aeg.com • The display shows the current setting. – = the acoustic signal is deactivated. – = the acoustic signal is activated. 2. Press to change the setting. 3. Press on/off to confirm the setting. 6.6 How to deactivate the TimeBeam Make sure the appliance is in user mode. 1. Press . • The indicators and , , , are off. still flashes. • The indicator • The display shows the current setting. – = TimeBeam is deactivated. – = TimeBeam is activated. to change the setting. 2. Press 3.
ENGLISH 13 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you select non compatible options, the appliance automatically deactivates one or more of them. Only the indicators of the still active options are on.
www.aeg.com 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets. After starting a programme, it may take up to 5 minutes for the appliance to recharge the resin in the water softener. It seems that the appliance is not working. The washing phase starts only after this procedure is completed. The procedure is repeated periodically. 8.
ENGLISH 15 Fill the rinse aid dispenser when the indicator (A) is clear. 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start a programme suitable for the type of load and the degree of soil. 9.1 Using the detergent A B 9.
www.aeg.com All buttons are inactive except for the on/off button. If the door is opened for more than 30 seconds during the drying phase, the running programme ends. It does not happen if the door is opened by AirDry function. Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again. Press and hold RESET until the appliance is in programme selection mode.
ENGLISH cleaner which is particularly suitable for this purpose. • Detergent tablets do not fully dissolve with short programmes. To prevent detergent residues on the tableware, we recommend that you use the tablets with long programmes. • Do not use more than the correct quantity of detergent. Refer to the instructions on the detergent packaging. 10.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1.
www.aeg.com 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. 3. Remove the flat filter (A). 4. Wash the filters. 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6.
ENGLISH CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 19 4. To install the spray arm back, press the spray arm upwards and simultaneously turn it counterclockwise until it locks into place. 11.2 Cleaning the upper spray arm We recommend to clean the upper spray arm regularly to prevent soil from clogging the holes. Clogged holes can cause unsatisfactory washing results. 1. Pull out the upper basket. 2.
www.aeg.com limescale buildup inside the appliance. Run long-duration programmes at least twice a month to prevent the buildup. 12. TROUBLESHOOTING WARNING! Improper repair of the appliance may pose a danger to the safety of the user. Any repairs must be performed by qualified personnel. to contact an Authorised Service Centre. Refer to the below table for information on possible problems. With some problems, the display shows an alarm code.
ENGLISH 21 Problem and alarm code Possible cause and solution The programme lasts too long. • If the delay start option is set, cancel the delay setting or wait for the end of the countdown. • Activate the TimeSaver option to reduce the programme duration. • Activating options can increase the programme duration. The remaining time in the display increases and skips nearly to the end of the programme duration. • This is not a defect. The appliance is working correctly.
www.aeg.com Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside the closed appliance. • There is no rinse aid or the dosage of rinse aid is not sufficient. Adjust the rinse aid level to a higher level. • Plastic items may need to be towel dried. • For the best drying performance, activate XtraDry and AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets.
ENGLISH 23 Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. • For washing delicate items and glassware, select the dedicated programme. Refer to "Programmes". The level of salt is low.
www.aeg.com The ‘standard programme’ is the standard cleaning cycle to which the information in the label and the fiche relates. This programme is suitable to clean normally soiled tableware and is the most efficient programme in terms of combined energy and water consumption. It is indicated as "Eco" programme. Programme time of standard cleaning cycle (min) 235 Duration of the left-on mode (min) 5 Sound power level (db(A) re 1pW) 42 Built in appliance Y/N Yes 14.
ENGLISH 25
www.aeg.
ENGLISH 27
117883322-A-402018 www.aeg.
