FSK93705P USER MANUAL FR Notice d'utilisation Lave-vaisselle
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ.................................................................................2 2. CONSIGNES DE SÉCURITÉ........................................................................................4 3. DESCRIPTION DE L'APPAREIL...................................................................................6 4. BANDEAU DE COMMANDE......................................................................................7 5. PROGRAMMES.................
FRANÇAIS 3 pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.1 Sécurité des enfants et des personnes vulnérables.
www.aeg.com • • • • • • • • • La pression de l'eau en fonctionnement (minimale et maximale) doit se situer entre 0.5 (0.05) / 8 (0.8) bar (MPa) Respectez le nombre maximal de 15 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger.
FRANÇAIS • L'appareil doit être relié à la terre. • Vérifiez que les paramètres figurant sur la plaque signalétique correspondent aux données électriques de votre réseau. • Utilisez toujours une prise de courant de sécurité correctement installée. • N'utilisez pas d'adaptateurs multiprises ni de rallonges. • Veillez à ne pas endommager la fiche secteur ni le câble d'alimentation. Le remplacement du câble d'alimentation de l'appareil doit être effectué par notre service après-vente agréé.
www.aeg.com appareils domestiques. Ne les utilisez pas pour éclairer votre logement. • Pour remplacer l'éclairage intérieur, contactez le service après-vente agréé. 2.6 Maintenance • Pour réparer l'appareil, contactez un service après-vente agréé. • Utilisez exclusivement des pièces d'origine. • Débranchez l'appareil de l'alimentation électrique. • Coupez le câble d'alimentation et mettez-le au rebut.
FRANÇAIS 3.1 TimeBeam 7 Durant la phase de séchage, lorsque l'option AirDry est activée, il est possible que la projection sur le sol ne soit pas totalement visible. Pour vérifier le temps restant au programme en cours, vous pouvez regarder l'affichage du bandeau de commande. Le faisceau TimeBeam affiche les informations suivantes sous la porte de l'appareil : • La durée du programme, lorsque le programme démarre. • 0:00 et CLEAN lorsque le programme est terminé.
www.aeg.com indique le programme par défaut : ECO 50°. Touche OK • En appuyant brièvement, vous confirmez la sélection du programme, des options et des réglages. • Appuyez longuement (3 secondes) pour lancer le programme MyFavourite. Si aucun programme n'a été mémorisé, le message suivant s'affiche : Régler MyFav.. 5.
FRANÇAIS Programme Degré de salissure Type de vaisselle Phases du programme Prewash 8) • Tous • Prélavage 9 Options 1) Ce programme vous permet d'optimiser votre consommation d'eau et d'énergie pour la vaisselle et les couverts normalement sales. Il s'agit du programme standard pour les instituts de tests. 2) L'appareil détecte le degré de salissure et la quantité de vaisselle dans les paniers. Il règle automatiquement la température et le volume d'eau, ainsi que la durée du lavage.
www.aeg.com Dans votre demande, notez la référence du produit (PNC) située sur la plaque signalétique. au manuel d'utilisation fourni avec votre appareil. Pour toute autre question concernant votre lave-vaisselle, veuillez vous reporter 6. RÉGLAGES 6.1 Liste des réglages Réglages Valeurs Description Régler MyFav. Liste des programmes Sélectionnez votre programme quotidien préféré. Reportez-vous aux informations correspondantes dans ce chapitre. AirDry ACTIVÉ DÉSAC.
FRANÇAIS 11 Réglages Valeurs Description Niveau liquide de rinçage Du niveau 0 au niveau 6 Niveau 0 = aucun liquide de rinçage n'est libéré. Pour régler la quantité de liquide de rinçage libérée en fonction de la dose nécessaire. Réglage d'usine : niveau 4. Langues Liste des langues. Pour sélectionner votre langue préférée. Langue par défaut : anglais. Affichage au sol Liste des couleurs. Aucune Pour sélectionner la couleur du TimeBeam ou désactiver le TimeBeam.
www.aeg.com 4. Sélectionnez un programme et appuyez sur la touche . Deux valeurs s'affichent. • Ajouter : sélectionnez une valeur pour ajouter une option au programme. • Effectué : sélectionnez la valeur pour enregistrer le programme sans option ou pour terminer l'ajout d'options au programme. 5. Appuyez sur . Si le programme est compatible avec l'option TimeSaver, les deux valeurs correspondant aux durées du programme correspondant s'affichent. • Rapide : sélectionnez la valeur pour activer TimeSaver.
FRANÇAIS 13 7.1 Liste des options Options Valeurs Descrizione Retard De 1 à 24 heures DÉSAC. (valeur par défaut) Pour retarder le départ du programme. XtraDry ACTIVÉ DÉSAC. (valeur par défaut) Pour améliorer les performances de séchage. Reportez-vous aux informations correspondantes dans ce chapitre. Extra Hygiene ACTIVÉ DÉSAC. (valeur par défaut) Garantit de meilleurs résultats d'hygiène en maintenant la température à 70 °C pendant au moins 10 minutes au cours de la dernière phase de rinçage.
www.aeg.com Cette option augmente la pression et la température de l'eau. Les phases de lavage et de séchage sont réduites. Les résultats de lavage seront les mêmes qu'avec la durée normale du programme. Les résultats de séchage peuvent être moins satisfaisants. Activez TimeSaver en suivant ces instructions : Sélectionnez un programme et appuyez correspondant aux durées du programme correspondant s'affichent. • Rapide : sélectionnez la valeur pour activer TimeSaver et appuyez sur pour confirmer.
FRANÇAIS 15 Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Réglage du niveau de l'adoucisseur d'eau 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Réglages d'usine. 2) N'utilisez pas de sel à ce niveau.
www.aeg.com 6. Tournez le couvercle du réservoir de sel régénérant vers la droite pour le refermer. ATTENTION! De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Afin d'éviter la corrosion, lancez immédiatement un programme après avoir rempli le réservoir de sel régénérant. Lorsque le réservoir de sel régénérant doit être rempli, le message correspondant s'affiche. ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle.
FRANÇAIS • Remplissez le réservoir de sel régénérant si l'affichage vous indique le message correspondant. • Remplissez le distributeur de liquide de rinçage si le message correspondant s'affiche. 3. Chargez les paniers. 4. Ajoutez du produit de lavage. 5. Réglez et lancez le programme adapté au type de vaisselle et au degré de salissure. 9.1 Utilisation du produit de lavage A B 17 9.2 Réglage et départ d'un programme Comment démarrer un programme 1.
www.aeg.com Le nombre d'heures disponibles pour le départ différé s'affiche (de 1 à 24). 4. Sélectionnez le nombre d'heures souhaité et appuyez sur pour confirmer. La liste des options s'affiche à nouveau. 5. Vous pouvez sélectionner d'autres options compatibles. 6. Appuyez à plusieurs reprises sur la touche jusqu'à ce que le programme sélectionné s'affiche. pour 7. Appuyez sur la touche confirmer la sélection. 8. Fermez la porte de l'appareil pour démarrer le décompte.
FRANÇAIS 19 • Au bout de 5 minutes si le programme n'a pas démarré. 10. CONSEILS 10.1 Raccordement Suivez les conseils ci-dessous pour garantir des résultats de lavage et de séchage optimaux au quotidien, et pour vous aider à protéger l'environnement. • Videz les plus gros résidus alimentaires des plats dans une poubelle. • Ne rincez pas vos plats à la main au préalable. Si nécessaire, sélectionnez un programme avec une phase de prélavage. • Utilisez toujours tout l'espace des paniers.
www.aeg.com • Ne placez pas dans l'appareil des objets pouvant absorber l'eau (éponges, chiffons de nettoyage). • Retirez les plus gros résidus alimentaires des plats. • Faites tremper la vaisselle contenant des aliments brûlés avant de la placer dans l'appareil. • Chargez les articles creux (tasses, verres et casseroles) en les retournant. • Vérifiez que les verres ne se touchent pas pour éviter qu'ils ne se brisent. • Placez les objets légers dans le panier supérieur.
FRANÇAIS 21 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 5.
www.aeg.com 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur 3. Nettoyez le bras d'aspersion à l'eau courante. Utilisez un outil pointu comme un cure-dent pour extraire toutes les particules de saleté incrustées dans les orifices. 4.
FRANÇAIS 23 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT AVERTISSEMENT! Une mauvaise réparation de l'appareil peut entraîner un danger pour la sécurité de l'utilisateur. Toute réparation ne doit être effectuée que par un technicien qualifié. Reportez-vous au tableau ci-dessous pour obtenir plus d'informations sur les problèmes possibles. Pour certains problèmes, un message s'affiche. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé.
www.aeg.com Problème Cause et solution possibles Le système de sécurité anti- • Fermez le robinet d'eau et contactez le service aprèsdébordement s'est déclenvente agréé. ché. Le message suivant s'affiche : L'appareil déborde ou présente un problème au niveau de l'arrivée d'eau. L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps.
FRANÇAIS Reportez-vous aux chapitres « Avant la première utilisation », « Utilisation quotidienne » ou « Conseils » pour connaître les autres causes probables. 25 Pour les autres messages ou problèmes qui ne sont pas décrits dans ce tableau, veuillez contacter un service après-vente agréé. Après avoir vérifié l'appareil, éteignez puis rallumez-le. Si le problème persiste, contactez le service après-vente agréé. 12.
www.aeg.com Problème Cause et solution possibles La vaisselle est mouillée. • Pour de meilleures performances de séchage, activez les options XtraDry et AirDry. • Le programme ne contient pas de phase de séchage ou une phase de séchage à basse température. • Le distributeur de liquide de rinçage est vide. • Il se peut que la qualité du liquide de rinçage soit en cause. • Il se peut que la qualité des pastilles tout en 1 soit en cause.
FRANÇAIS Problème 27 Cause et solution possibles Dépôts calcaires sur la vaissel- • Le niveau de sel régénérant est bas. Après avoir allule, dans la cuve et à l'intérieur mé l'appareil, regardez si la notification de remplissade la porte. ge du sel régénérant s'affiche. • Le bouchon du réservoir de sel régénérant est dévissé. • L'eau de votre arrivée est dure. Reportez-vous au chapitre « Adoucisseur d'eau ».
www.aeg.com Consommation électrique Mode « Veille » (W) 5.0 Mode « Éteint » (W) 0.10 1) Reportez-vous à la plaque signalétique pour d'autres valeurs. 2) Si l'eau chaude est produite à partir de sources d'énergie respectueuses de l'environnement (par exemple panneaux solaires), utilisez une arrivée d'eau chaude afin de réduire la consommation d'énergie. 14. EN MATIÈRE DE PROTECTION DE L'ENVIRONNEMENT Recyclez les matériaux portant le électroniques. Ne jetez pas les appareils symbole .
FRANÇAIS 29
www.aeg.
FRANÇAIS 31
117876731-A-282018 www.aeg.