FSK93705P EN FR USER MANUAL User Manual Dishwasher Notice d'utilisation Lave-vaisselle 2 26
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
ENGLISH • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. • UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Top spray arm Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 TimeBeam TimeBeam displays the following information on the floor below the appliance door: • The programme duration when the programme begins. • 0:00 and CLEAN when the programme is completed. • DELAY and the countdown duration when the delay start begins. • An alarm code when the appliance has a malfunction.
ENGLISH 7 When AirDry is activated during the drying phase, the projection on the floor may not be completely visible. To check the remaining time of the running programme, look at the control panel display. 4. CONTROL PANEL 1 2 3 6 1 2 3 4 4 5 5 OK button 6 Navigation button (down) On/off button Navigation button (up) Display Option button 4.1 Button behaviour Navigation buttons (up and down) • Use these buttons to scroll the lists and information texts on the display.
www.aeg.
ENGLISH 9 5.1 Consumption values Water (l) Energy (kWh) Duration (min) 11 0.857 235 AutoSense 45°-70° 8 - 15 0.7 - 1.7 46 - 170 ProZone 50°-65° 14 - 16 1.2 - 1.5 160 - 180 12.5 - 14.5 1.4 - 1.7 170 - 190 10 0.9 30 Glass 45° 12 - 14 0.8 - 1.0 82 - 92 Extra Silent 12 - 13 1.1 - 1.3 230 - 250 4 0.
www.aeg.com Settings Values Description Key tones Click Beep Off Set the sound of the buttons when pressed. Volume From level 1 to level 10 Adjust the sound volume. Brightness From level 0 to level 9 Adjust the brightness of the display. Contrast From level 0 to level 9 Adjust the contrast of the display. Water hardness From level 1 to level 10 Adjust the level of the water softener according to the water hardness in your area. Factory setting: level 5.
ENGLISH 11 6.4 How to save the MyFavourite programme You can save your favourite programme along with applicable options. It is not possible to save the MyFavourite programme with the Delay option. You can save one programme at a time. A new setting cancels the previous one. 1. Press . The display shows the option list. . 2. Select Settings and press The display shows the setting list. 3. Select Set MyFavourite and press . The display shows the programme list. . 4.
www.aeg.com 7.1 Option list Options Values Description Delay From 1 to 24 hours OFF (default value) Delays the start of a programme. XtraDry ON OFF (default value) Boosts the drying performance. Refer to specific information provided in this chapter. Extra Hygiene ON OFF (default value) Ensures better hygiene results by keeping the temperature at 70 °C for at least 10 minutes during the last rinsing phase. Settings Shows the appliance settings 7.2 How to set an option 7.
ENGLISH If TimeSaver is applicable to the selected programme, the display shows two values with corresponding programme durations. • Fast: select the value to activate TimeSaver and press confirm. to 13 • Normal: select the value to deactivate TimeSaver and press to confirm. Activating TimeSaver deactivates XtraDry and vice versa. 8. BEFORE FIRST USE When you activate the appliance for the first time, you need to set the language. The default language is English. 1. Set the language.
www.aeg.com German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level. Regardless of the type of detergent used, set the proper water hardness level to keep the salt refill notification active. Multi-tabs containing salt are not effective enough to soften hard water. 8.2 The salt container CAUTION! Use rough salt designed for dishwashers only. Fine salt increases the risk of corrosion.
ENGLISH How to fill the rinse aid dispenser A B 15 3. Remove the spilled rinse aid with an absorbent cloth to prevent excessive foam formation. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) is clear. When the rinse aid dispenser needs refilling, the display shows the related message.
www.aeg.com 3. If the programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance door. 4. Close the lid. Make sure that the lid locks into position. The display shows the number of hours available for the delay start (from 1 to 24). 4. Select the desired number of hours 9.2 Setting and starting a programme 6. Press repeatedly until the display shows the selected programme. How to start a programme 1. Press the on/off button to activate the appliance.
ENGLISH Opening the door while the appliance operates Opening the door while a programme is running stops the appliance. It may affect the energy consumption and the programme duration. After closing the door, the appliance continues from the point of interruption. If the door is opened for more than 30 seconds during the drying phase, the running programme ends. It does not happen if the door is opened by AirDry function.
www.aeg.com 10.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid, complete the following steps: 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5.
ENGLISH 19 C B A 1. Turn the filter (B) counterclockwise and remove it. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 4. Wash the filters.
www.aeg.com 11.2 Cleaning the upper spray arm We recommend to clean the upper spray arm regularly to prevent soil from clogging the holes. simultaneously turn it counterclockwise until it locks into place. Clogged holes can cause unsatisfactory washing results. 1. Pull out the upper basket. 2. To detach the spray arm from the basket, press the spray arm upwards and simultaneously turn it clockwise. 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents.
ENGLISH 21 12. TROUBLESHOOTING WARNING! Improper repair of the appliance may pose a danger to the safety of the user. Any repairs must be performed by qualified personnel. to contact an Authorised Service Centre. Refer to the below table for information on possible problems. With some problems, the display shows a message. The majority of problems that may occur can be solved without the need Problem Possible cause and solution You cannot activate the appliance.
www.aeg.com Problem Possible cause and solution The programme lasts to long. • If the delay start is set, cancel the delay setting or wait for the end of the countdown. • Activate the TimeSaver option to reduce the programme duration. • Activating options can increase the programme duration. The remaining time in the display increases and skips nearly to the end of the programme duration. • This is not a defect. The appliance is working correctly. Small leak from the appliance door.
ENGLISH 23 Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside the closed appliance. • There is no rinse aid or the dosage of rinse aid is not sufficient. Adjust the rinse aid level to a higher level. • Plastic items may need to be towel dried. • For the best drying performance, activate XtraDry and AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets. There are whitish streaks or bluish layers on glasses and dishes.
www.aeg.com Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • The level of salt is low. After you activate the appliance, check the display for the salt refill notification. • The cap of the salt container is loose. • Your tap water is hard. Refer to "The water softener". • Use salt and set regeneration of the water softener even when multi-functional tablets are used. Refer to "The water softener".
ENGLISH Drying efficiency class on a scale from G (least efficient) to A (most efficient) A The ‘standard programme’ is the standard cleaning cycle to which the information in the label and the fiche relates. This programme is suitable to clean normally soiled tableware and is the most efficient programme in terms of combined energy and water consumption. It is indicated as "Eco" programme.
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................27 2. CONSIGNES DE SÉCURITÉ......................................................................................28 3. DESCRIPTION DE L'APPAREIL.................................................................................30 4. BANDEAU DE COMMANDE....................................................................................31 5. PROGRAMMES....................
FRANÇAIS 1. 27 INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.1 Sécurité des enfants et des personnes vulnérables.
www.aeg.com pour une utilisation privée, par les clients, dans des hôtels et autres lieux de séjour. Ne modifiez pas les caractéristiques de cet appareil. La pression de l'eau en fonctionnement (minimale et maximale) doit se situer entre 0.5 (0.05) / 8 (0.8) bar (MPa) Respectez le nombre maximal de 15 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger.
FRANÇAIS • Installez l'appareil dans un lieu sûr et adapté répondant aux exigences d'installation. 2.2 Branchement électrique AVERTISSEMENT! Risque d'incendie ou d'électrocution. • L'appareil doit être relié à la terre. • Vérifiez que les paramètres figurant sur la plaque signalétique correspondent aux données électriques de votre réseau. • Utilisez toujours une prise de courant de sécurité correctement installée. • N'utilisez pas d'adaptateurs multiprises ni de rallonges.
www.aeg.com • Cet appareil dispose d'un éclairage intérieur qui s'allume lors de l'ouverture de la porte et s'éteint lors de sa fermeture. • Le type d'ampoule utilisé pour cet appareil est uniquement destiné aux appareils domestiques. Ne les utilisez pas pour éclairer votre logement. • Pour remplacer l'éclairage intérieur, contactez le service après-vente agréé. 2.6 Maintenance • Pour réparer l'appareil, contactez un service après-vente agréé. • Utilisez exclusivement des pièces d'origine. 2.
FRANÇAIS 3.1 TimeBeam 31 Durant la phase de séchage, lorsque l'option AirDry est activée, il est possible que la projection sur le sol ne soit pas totalement visible. Pour vérifier le temps restant au programme en cours, vous pouvez regarder l'affichage du bandeau de commande. Le faisceau TimeBeam affiche les informations suivantes sous la porte de l'appareil : • La durée du programme, lorsque le programme démarre. • 0:00 et CLEAN lorsque le programme est terminé.
www.aeg.com indique le programme par défaut : ECO 50°. Touche OK • En appuyant brièvement, vous confirmez la sélection du programme, des options et des réglages. • Appuyez longuement (3 secondes) pour lancer le programme MyFavourite. Si aucun programme n'a été mémorisé, le message suivant s'affiche : Régler MyFav.. 5.
FRANÇAIS Programme Degré de salissure Type de vaisselle Phases du programme Prewash 8) • Tous • Prélavage 33 Options 1) Ce programme vous permet d'optimiser votre consommation d'eau et d'énergie pour la vaisselle et les couverts normalement sales. Il s'agit du programme standard pour les instituts de tests. 2) L'appareil détecte le degré de salissure et la quantité de vaisselle dans les paniers. Il règle automatiquement la température et le volume d'eau, ainsi que la durée du lavage.
www.aeg.com Dans votre demande, notez la référence du produit (PNC) située sur la plaque signalétique. au manuel d'utilisation fourni avec votre appareil. Pour toute autre question concernant votre lave-vaisselle, veuillez vous reporter 6. RÉGLAGES 6.1 Liste des réglages Réglages Valeurs Description Régler MyFav. Liste des programmes Sélectionne votre programme quotidien préféré. Reportez-vous aux informations correspondantes dans ce chapitre. AirDry ACTIVÉ DÉSAC.
FRANÇAIS 35 Réglages Valeurs Description Niveau liquide de rinçage Du niveau 0 au niveau 6 Niveau 0 = aucun liquide de rinçage n'est libéré. Pour régler la quantité de liquide de rinçage libérée en fonction de la dose nécessaire. Réglage d'usine : niveau 4. Langues Liste des langues. Pour sélectionner votre langue préférée. Langue par défaut : anglais. Affichage au sol Blanc Aucune Activer ou désactiver le TimeBeam. Réglage d'usine : Blanc.
www.aeg.com 4. Sélectionnez un programme et appuyez sur la touche . Deux valeurs s'affichent. • Ajouter : sélectionnez une valeur pour ajouter une option au programme. • Effectué : sélectionnez la valeur pour enregistrer le programme sans option ou pour terminer l'ajout d'options au programme. 5. Appuyez sur . Si le programme est compatible avec l'option TimeSaver, les deux valeurs correspondant aux durées du programme correspondant s'affichent. • Rapide : sélectionnez la valeur pour activer TimeSaver.
FRANÇAIS 37 7.1 Liste des options Options Valeurs Description Retard De 1 à 24 heures DÉSAC. (valeur par défaut) Pour retarder le départ du programme. XtraDry ACTIVÉ DÉSAC. (valeur par défaut) Pour améliorer les performances de séchage. Reportez-vous aux informations correspondantes dans ce chapitre. Extra Hygiene ACTIVÉ DÉSAC. (valeur par défaut) Garantit de meilleurs résultats d'hygiène en maintenant la température à 70 °C pendant au moins 10 minutes au cours de la dernière phase de rinçage.
www.aeg.com Cette option augmente la pression et la température de l'eau. Les phases de lavage et de séchage sont réduites. Les résultats de lavage seront les mêmes qu'avec la durée normale du programme. Les résultats de séchage peuvent être moins satisfaisants. Activez TimeSaver en suivant ces instructions : Sélectionnez un programme et appuyez correspondant aux durées du programme correspondant s'affichent. • Rapide : sélectionnez la valeur pour activer TimeSaver et appuyez sur pour confirmer.
FRANÇAIS 39 Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Réglage du niveau de l'adoucisseur d'eau 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Réglages d'usine. 2) N'utilisez pas de sel à ce niveau.
www.aeg.com 6. Tournez le couvercle du réservoir de sel régénérant vers la droite pour le refermer. ATTENTION! De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Afin d'éviter la corrosion, lancez immédiatement un programme après avoir rempli le réservoir de sel régénérant. Lorsque le réservoir de sel régénérant doit être rempli, le message correspondant s'affiche. ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle.
FRANÇAIS • Remplissez le réservoir de sel régénérant si l'affichage vous indique le message correspondant. • Remplissez le distributeur de liquide de rinçage si le message correspondant s'affiche. 3. Chargez les paniers. 4. Ajoutez du produit de lavage. 5. Réglez et lancez le programme adapté au type de vaisselle et au degré de salissure. 9.1 Utilisation du produit de lavage A B 41 9.2 Réglage et départ d'un programme Comment démarrer un programme 1.
www.aeg.com Le nombre d'heures disponibles pour le départ différé s'affiche (de 1 à 24). 4. Sélectionnez le nombre d'heures souhaité et appuyez sur pour confirmer. La liste des options s'affiche à nouveau. 5. Vous pouvez sélectionner d'autres options compatibles. 6. Appuyez à plusieurs reprises sur la touche jusqu'à ce que le programme sélectionné s'affiche. pour 7. Appuyez sur la touche confirmer la sélection. 8. Fermez la porte de l'appareil pour démarrer le décompte.
FRANÇAIS 43 • Au bout de 5 minutes si le programme n'a pas démarré. 10. CONSEILS 10.1 Raccordement Suivez les conseils ci-dessous pour garantir des résultats de lavage et de séchage optimaux au quotidien, et pour vous aider à protéger l'environnement. • Videz les plus gros résidus alimentaires des plats dans une poubelle. • Ne rincez pas vos plats à la main au préalable. Si nécessaire, sélectionnez un programme avec une phase de prélavage. • Utilisez toujours tout l'espace des paniers.
www.aeg.com • Ne placez pas dans l'appareil des objets pouvant absorber l'eau (éponges, chiffons de nettoyage). • Retirez les plus gros résidus alimentaires des plats. • Faites tremper la vaisselle contenant des aliments brûlés avant de la placer dans l'appareil. • Chargez les articles creux (tasses, verres et casseroles) en les retournant. • Vérifiez que les verres ne se touchent pas pour éviter qu'ils ne se brisent. • Placez les objets légers dans le panier supérieur.
FRANÇAIS 45 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 5.
www.aeg.com 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur 3. Nettoyez le bras d'aspersion à l'eau courante. Utilisez un outil pointu comme un cure-dent pour extraire toutes les particules de saleté incrustées dans les orifices. 4.
FRANÇAIS 47 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT AVERTISSEMENT! Une mauvaise réparation de l'appareil peut entraîner un danger pour la sécurité de l'utilisateur. Toute réparation ne doit être effectuée que par un technicien qualifié. Reportez-vous au tableau ci-dessous pour obtenir plus d'informations sur les problèmes possibles. Pour certains problèmes, un message s'affiche. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé.
www.aeg.com Problème Cause et solution possibles Le système de sécurité anti- • Fermez le robinet d'eau et contactez le service aprèsdébordement s'est déclenvente agréé. ché. Le message suivant s'affiche : L'appareil déborde ou présente un problème au niveau de l'arrivée d'eau. L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps.
FRANÇAIS Reportez-vous aux chapitres « Avant la première utilisation », « Utilisation quotidienne » ou « Conseils » pour connaître les autres causes probables. 49 Pour les autres messages ou problèmes qui ne sont pas décrits dans ce tableau, veuillez contacter un service après-vente agréé. Après avoir vérifié l'appareil, éteignez puis rallumez-le. Si le problème persiste, contactez le service après-vente agréé. 12.
www.aeg.com Problème Cause et solution possibles La vaisselle est mouillée. • Pour de meilleures performances de séchage, activez les options XtraDry et AirDry. • Le programme ne contient pas de phase de séchage ou une phase de séchage à basse température. • Le distributeur de liquide de rinçage est vide. • Il se peut que la qualité du liquide de rinçage soit en cause. • Il se peut que la qualité des pastilles tout en 1 soit en cause.
FRANÇAIS Problème 51 Cause et solution possibles Dépôts calcaires sur la vaissel- • Le niveau de sel régénérant est bas. Après avoir allule, dans la cuve et à l'intérieur mé l'appareil, regardez si la notification de remplissade la porte. ge du sel régénérant s'affiche. • Le bouchon du réservoir de sel régénérant est dévissé. • L'eau de votre arrivée est dure. Reportez-vous au chapitre « Adoucisseur d'eau ».
www.aeg.com consommation d’électricité en mode laissé sur marche (W) 5.0 Consommation d’eau en litres par an, sur la base de 280 cycles de lavage standard. La consommation réelle d’eau dépend des conditions d’utilisation l’appareil 3080 classe d’efficacité de séchage sur une échelle de G (appareils les moins efficaces) à A (appareils les plus efficaces) A le «programme standard» est le cycle de lavage standard auquel se rapportent les informations qui figurent sur l’étiquette et sur la fiche.
FRANÇAIS 53
www.aeg.
FRANÇAIS 55
117877172-A-422018 www.aeg.