FSS5360XZ EN DE PL USER MANUAL User Manual Dishwasher Benutzerinformation Geschirrspüler Instrukcja obsługi Zmywarka 2 23 47
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
ENGLISH • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. • UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 9 8 7 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 Beam-on-Floor The Beam-on-Floor is a light that is displayed on the floor below the appliance door. • When the programme starts, a red light comes on and stays on for the duration of the programme. • When the programme is completed, a green light comes on. • When the appliance has a malfunction, the red light flashes.
ENGLISH 4. CONTROL PANEL 1 1 2 3 4 5 2 On/off button Display Delay button Programme button (up) Programme button (down) 3 4 6 7 8 9 5 6 7 8 9 TimeSaver button XtraDry button RESET button Indicators 4.1 Indicators Indicator Description Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. 5.
www.aeg.com Programme Degree of soil Type of load Programme phases Options P5 • Normal or light soil • Delicate crockery and glassware • Wash 45 °C • Rinses • Dry • XtraDry 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets .
ENGLISH 9 To enter user mode, press and hold • Activation or deactivation of the rinse aid empty notification. • Activation or deactivation of AirDry. simultaneously and indicators , , the display is blank. As the appliance stores the saved settings, there is no need to configure it before every cycle. and until the flash and 6.
www.aeg.com How to set the water softener level Make sure the appliance is in user mode. 1. Press = the rinse aid empty notification is deactivated. 3. Press on/off to confirm the setting. 6.4 Acoustic signals . , • The indicators are off. Acoustic signals sound when a malfunction of the appliance occurs. It is not possible to deactivate these acoustic signals. and • The indicator still flashes. • The display shows the current setting: e.g. = level 5. 2. Press repeatedly to change the setting.
ENGLISH During the drying phase, the door opens automatically and remains ajar. CAUTION! Do not try to close the appliance door within 2 minutes after automatic opening. This can cause damage to the appliance. AirDry is automatically activated with all programmes excluding applicable). (if 11 How to deactivate AirDry Make sure the appliance is in user mode. 1. Press . • The indicators are off. , and • The indicator still flashes. • The display shows the current setting: = AirDry activated. 2.
www.aeg.com The display shows the updated programme duration. 7.2 TimeSaver This option increases the pressure and the temperature of the water. The washing and the drying phases are shorter. The washing results are the same as with the normal programme duration. The drying results can decrease. How to activate TimeSaver Press . The related indicator is on. The display shows the updated programme duration. The total programme duration decreases by approximately 50%. 8. BEFORE FIRST USE 1.
ENGLISH 8.2 How to fill the rinse aid dispenser A D B C M AX 4 1. Press the release button (D) to open the lid (C). 2. Pour the rinse aid in the dispenser (A) until the liquid reaches the fill level 'max'. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the release button locks into position. 1 3 2 + CAUTION! Only use rinse aid specifically designed for dishwashers.
www.aeg.com A 30 B Starting a programme with delay start D 1. Set a programme. 20 C 1. Press the release button (B) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (A). 3. If the programme has a prewash phase, put a small quantity of detergent in the compartment (D). 4. Close the lid. Make sure that the release button locks into position. 9.
ENGLISH Cancelling the programme Press and hold RESET until the appliance is in programme selection mode. Make sure that there is detergent in the detergent dispenser before you start a new programme. End of the programme When the programme is completed the display shows 0:00. 15 All buttons are inactive except for the on/off button. 1. Press the on/off button or wait for the Auto Off function to automatically deactivate the appliance.
www.aeg.com 10.4 Loading the baskets • Only use the appliance to wash items that are dishwasher-safe. • Do not put in the appliance items made of wood, horn, aluminium, pewter and copper. • Do not put in the appliance items that can absorb water (sponges, household cloths). • Remove remaining food from the items. • Make soft the remaining burned food on the items. • Put hollow items (cups, glasses and pans) with the opening down. • Make sure that cutlery and dishes do not bond together.
ENGLISH 17 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 4. Wash the filters. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.
www.aeg.com • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance. To prevent this, we recommend to run long duration programmes at least 2 times per month. • To maintain the performance of your appliance at its best, we recommend to use monthly a specific cleaning product for dishwashers. Follow carefully the instructions on the packaging of the product. 12.
ENGLISH Problem and alarm code 19 Possible cause and solution The appliance stops and • It is normal. It provides optimal cleaning results and enstarts more times during opergy savings. eration. The program lasts too long. • Select the TimeSaver option to shorten the program time. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown. The remaining time in the • This is not a defect. The appliance is working correctly.
www.aeg.com Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option XtraDry and set AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets.
ENGLISH 21 Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. The level of salt is low, check the refill indicator. The cap of the salt container is loose. Your tap water is hard.
www.aeg.com product to your local recycling facility or contact your municipal office.
DEUTSCH 23 INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE........................................................................................... 24 2. SICHERHEITSANWEISUNGEN.................................................................................26 3. GERÄTEBESCHREIBUNG......................................................................................... 27 4. BEDIENFELD..............................................................................................................28 5. PROGRAMME..
1. www.aeg.com SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
DEUTSCH Bauernhöfe, Personalküchenbereiche in Geschäften, Büros und anderen Arbeitsumfeldern. – Für Gäste in Hotels, Motels, Pensionen und anderen wohnungsähnlichen Räumlichkeiten. Nehmen Sie keine technischen Änderungen am Gerät vor. Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt.
www.aeg.com 2. SICHERHEITSANWEISUNGEN 2.1 Montage WARNUNG! Die Montage des Geräts darf nur von einer qualifizierten Fachkraft durchgeführt werden. • Entfernen Sie das gesamte Verpackungsmaterial. • Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. • Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann, und benutzen Sie das Gerät nicht, wenn die Temperatur unter 0 °C absinkt. • Halten Sie sich an die mitgelieferte Montageanleitung.
DEUTSCH solche nicht in die Nähe oder auf das Gerät. des Wasserzulaufschlauchs an den autorisierten Kundendienst. 2.4 Gebrauch 2.5 Service • Setzen oder stellen Sie sich niemals auf die geöffnete Gerätetür. • Geschirrspüler-Reinigungsmittel sind gefährlich. Beachten Sie die Sicherheitsanweisungen auf der Reinigungsmittelverpackung. • Trinken Sie nicht das Wasser aus dem Gerät und verwenden Sie es nicht zum Spielen. • Nehmen Sie kein Geschirr aus dem Gerät, bevor das Programm beendet ist.
www.aeg.com 9 Besteckkorb 10 Unterkorb 11 Oberkorb 3.1 Beam-on-Floor Nach dem Abschalten des Gerätes erlischt der Beamon-Floor. Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Boden projiziert wird. Wird AirDry während der Trockenphase eingeschaltet, ist die Projektion auf dem Boden möglicherweise nicht vollständig sichtbar. Sie können dann auf dem Bedienfeld sehen, ob das Programm beendet wurde.
DEUTSCH 29 5.
www.aeg.com Wasserverbrauch (l) Energieverbrauch (kWh) Dauer (min.) P2 7 - 12 0.7 - 1.5 45 - 160 P3 13 - 15 1.4 - 1.6 140 - 160 P4 9 0.8 30 P5 13 - 14 0.9 - 1.1 70 - 85 Programm1) 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Diese Informationen sind nur für unabhängige Prüfinstitute oder akkreditierte Laboratorien vorgesehen. info.test@dishwasher-production.
DEUTSCH , und blinken und das Display nichts anzeigt. 6.2 Wasserenthärter Der Wasserenthärter entfernt Mineralien aus dem Spülwasser, die sich nachteilig auf die Spülergebnisse und das Gerät auswirken könnten. Je höher der Mineralgehalt ist, um so härter ist Ihr Wasser. Die Wasserhärte 31 wird in gleichwertigen Einheiten gemessen. Der Enthärter muss entsprechend der Wasserhärte Ihres Gebietes eingestellt werden. Ihr lokales Wasserwerk kann Sie über die Wasserhärte in Ihrem Gebiet informieren.
www.aeg.com 2. Drücken Sie wiederholt zum Ändern der Einstellung. 3. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. = die Klarspülmittelnachfüllanzeige ist ausgeschaltet. 3. Drücken Sie Ein/Aus zum Bestätigen der Einstellung. 6.3 Klarspülmittelnachfüllanzeige 6.4 Signaltöne Das Klarspülmittel ermöglicht das Trocknen des Geschirrs ohne Streifen und Flecken. Das Klarspülmittel wird automatisch während der heißen Spülphase abgegeben.
DEUTSCH 33 XtraDry-Option oder schalten Sie AirDry ein. VORSICHT! Haben Kinder Zugang zum Gerät, wird empfohlen AirDry auszuschalten, da das Öffnen der Tür eine Gefahr darstellen könnte. So schalten Sie AirDry aus Während der Trockenphase wird die Tür automatisch geöffnet und bleibt einen Spaltbreit offen. VORSICHT! Versuchen Sie nicht, die Gerätetür innerhalb der ersten 2 Minuten nach der automatischen Öffnung zu schließen. Andernfalls kann das Gerät beschädigt werden.
www.aeg.com Ist die Option nicht mit einem Programm kombinierbar, leuchtet die entsprechende Kontrolllampe nicht oder sie blinkt ein paar Sekunden schnell und erlischt dann. Die eingeschalteten Optionen können sich auf den Wasser- und Energieverbrauch sowie die Programmdauer auswirken. 7.1 XtraDry Schalten Sie diese Option ein, um die Trocknungsleistung zu erhöhen.
DEUTSCH 8.1 Salzbehälter VORSICHT! Verwenden Sie ausschließlich speziell für Geschirrspüler bestimmtes grobkörniges Salz. Mit feinem Salz besteht erhöhte Korrosionsgefahr. Das Salz wird für die Regenerierung des Filterharzes im Wasserenthärter und zur Erzielung guter Spülergebnisse im täglichen Gebrauch benötigt. 35 VORSICHT! Beim Befüllen des Salzbehälters können Wasser und Salz austreten. Starten Sie nach dem Füllen des Salzbehälters umgehend ein Programm, um Korrosion zu verhindern. 8.
www.aeg.com 4. Schließen Sie den Deckel. Achten Sie darauf, dass die Entriegelungstaste einrastet. Sie können den Regler der Zugabemenge (B) zwischen Position 1 (geringste Menge) und Position 4 oder 6 (größte Menge) einstellen. 9. TÄGLICHER GEBRAUCH 1. Öffnen Sie den Wasserhahn. 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. • Füllen Sie den Salzbehälter auf, wenn die Kontrolllampe Salz leuchtet.
DEUTSCH 4. Stellen Sie die verfügbaren Optionen ein. 5. Schließen Sie die Gerätetür, um das Programm zu starten. Starten eines Programms mit Zeitvorwahl 1. Wählen Sie ein Programm. 2. Drücken Sie die Taste wiederholt, bis im Display die gewünschte Zeitvorwahl angezeigt wird (zwischen 1 und 24 Stunden). Die Kontrolllampe der Zeitvorwahl leuchtet auf. 3. Schließen Sie die Gerätetür, um den Countdown zu starten.
www.aeg.com • • • • verfügbar) oder wählen Sie ein Programm mit Vorspülgang. Nutzen Sie die Körbe immer ganz aus. Wenn Sie das Gerät beladen, achten Sie darauf, dass das Geschirr komplett von dem Wasser aus den Sprüharmdüsen erreicht und gespült wird. Achten Sie darauf, dass das Geschirr sich weder berührt noch von anderem Geschirr verdeckt wird. Sie können Geschirrspülreiniger, Klarspüler und Salz separat oder Kombi-Reinigungstabletten (z.B. „3in1“, „4in1“, „All-in-1“) verwenden.
DEUTSCH • Vergewissern Sie sich, dass sich der Sprüharm ungehindert bewegen kann, bevor Sie ein Programm starten. 10.5 Vor dem Starten eines Programms Kontrollieren Sie folgende Punkte: • Die Filter sind sauber und ordnungsgemäß eingesetzt. • Der Deckel des Salzbehälters ist fest geschlossen. • Die Sprüharme sind nicht verstopft. • Geschirrspülsalz und Klarspülmittel sind vorhanden (außer Sie verwenden Multi-Reinigungstabletten). • Die Geschirrteile sind richtig in den Körben angeordnet.
www.aeg.com 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet. 4. Reinigen Sie die Filter. VORSICHT! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 5.
DEUTSCH 11.4 Reinigung des Geräteinnenraums • Reinigen Sie das Gerät und die Gummidichtung der Tür sorgfältig mit einem weichen, feuchten Tuch. • Wenn Sie regelmäßig Kurzprogramme verwenden, können diese zu Fett- und Kalkablagerungen im Gerät führen. Um dieses zu vermeiden, wird empfohlen, 41 mindestens zweimal im Monat Programme mit langer Laufzeit zu verwenden.
www.aeg.com Störung und Alarmcode Mögliche Ursache und Abhilfe Es läuft kein Wasser in das Gerät. • Stellen Sie sicher, dass der Wasserzulaufhahn geöffnet ist. • Vergewissern Sie sich, dass der Wasserdruck der Wasserversorgung nicht zu niedrig ist. Diese Informationen erhalten Sie von Ihrem lokalen Wasserversorger. • Stellen Sie sicher, dass der Wasserzulaufhahn nicht verstopft ist. • Vergewissern Sie sich, dass das Sieb im Zulaufschlauch nicht verstopft ist.
DEUTSCH Störung und Alarmcode 43 Mögliche Ursache und Abhilfe Klappernde/schlagende Ge- • Das Geschirr ist nicht richtig in den Körben eingeordnet. räusche aus dem GeräteinSiehe Broschüre zum Beladen der Körbe. neren. • Achten Sie darauf, dass sich die Sprüharme frei drehen können. Das Gerät löst die Sicherung • Die abgesicherte Stromstärke reicht nicht für den gleichaus. zeitigen Betrieb aller eingeschalteten Geräte. Überprüfen Sie, für welche Stromstärke die Steckdose bzw.
www.aeg.com Störung Mögliche Ursache und Abhilfe Wasserflecken und andere Flecken auf Gläsern und Geschirr. • Die zugegebene Klarspülmittelmenge ist zu niedrig. Stellen Sie eine höhere Klarspülmittelmenge ein. • Die Ursache kann in der Qualität des Klarspülmittels liegen. Das Geschirr ist nass. • Schalten Sie die Option XtraDry ein, und stellen Sie AirDry ein, um die beste Trocknungsleistung zu erzielen.
DEUTSCH 45 Störung Mögliche Ursache und Abhilfe Kalkablagerungen auf dem Geschirr, im Innenraum und auf der Türinnenseite. • Es befindet sich zu wenig Salz im Behälter, prüfen Sie die Nachfüllanzeige. • Der Deckel des Salzbehälters ist locker. • Ihr Leitungswasser ist hart. Siehe „Wasserenthärter“. • Verwenden Sie stets Salz, auch wenn Sie Multi-Reinigungstabletten nutzen und stellen Sie die Regenerierung des Wasserenthärters ein. Siehe „Wasserenthärter“.
www.aeg.com 14. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte. Entsorgen Sie Geräte mit diesem Symbol nicht mit dem Hausmüll. Bringen Sie das Gerät zu Ihrer örtlichen Sammelstelle oder wenden Sie sich an Ihr Gemeindeamt.
POLSKI 47 SPIS TREŚCI 1. INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA............................................48 2. WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA.............................................50 3. OPIS URZĄDZENIA............................................................................................51 4. PANEL STEROWANIA....................................................................................... 52 5. PROGRAMY....................................................................................
1. www.aeg.com INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA Przed przystąpieniem do instalacji i rozpoczęciem eksploatacji urządzenia należy uważnie zapoznać się z załączoną instrukcją obsługi. Producent nie odpowiada za obrażenia ciała ani szkody spowodowane nieprawidłową instalacją lub eksploatacją urządzenia. Należy zachować instrukcję obsługi w bezpiecznym i łatwo dostępnym miejscu do wykorzystania w przyszłości. 1.
POLSKI 49 1.2 Ogólne zasady bezpieczeństwa • • • • • • • • • • • Urządzenie jest przeznaczone do użytku w gospodarstwie domowym oraz do podobnych zastosowań w takich miejscach, jak: – gospodarstwa rolne, kuchnie w obiektach sklepowych, biurowych oraz innych placówkach pracowniczych; – do obsługi przez klientów w hotelach, motelach, obiektach noclegowych i innych obiektach mieszkalnych. Nie zmieniać parametrów technicznych urządzenia.
www.aeg.com 2. WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA 2.1 Instalacja OSTRZEŻENIE! Urządzenie może zainstalować wyłącznie wykwalifikowana osoba. • • • • • • Usunąć wszystkie elementy opakowania. Nie instalować ani nie używać uszkodzonego urządzenia. Nie instalować ani nie używać urządzenia w miejscach, w których panuje temperatura poniżej 0°C. Należy postępować zgodnie z instrukcją instalacji dołączoną do urządzenia. Zachować ostrożność podczas przenoszenia urządzenia, ponieważ jest ono ciężkie.
POLSKI • substancji ani przedmiotów nasączonych łatwopalnymi substancjami. W razie uszkodzenia węża dopływowego należy natychmiast zamknąć zawór wody i wyjąć wtyczkę z gniazda elektrycznego. Należy skontaktować się z autoryzowanym centrum serwisowym w celu wymiany węża dopływowego. 2.5 Serwis • 2.4 Eksploatacja • • • • • • Nie siadać ani nie stawać na otworzonych drzwiach urządzenia. Detergenty do zmywarki są niebezpieczne.
www.aeg.com 5 6 7 8 Zbiornik soli Otwór wentylacyjny Dozownik płynu nabłyszczającego Dozownik detergentu 9 Kosz na sztućce 10 Dolny kosz 11 Górny kosz 3.1 Beam-on-Floor Jeśli podczas fazy suszenia włączona jest opcja AirDry, obraz wyświetlany na podłodze może nie być widoczny w całości. Aby upewnić się, że zakończył się cykl, należy sprawdzić wskazanie na panelu sterowania. Wyświetlacz Beam-on-Floor wyświetla wiązkę światła na podłodze przed drzwiami urządzenia.
POLSKI 53 5.
www.aeg.com Zużycie wody (l) Zużycie energii (kWh) Czas trwania (min) P4 9 0.8 30 P5 13 - 14 0.9 - 1.1 70 - 85 Program 1) 1) Parametry eksploatacyjne mogą ulec zmianie w zależności od ciśnienia i temperatury wody, zmian w napięciu zasilania, użytych opcji oraz ilości naczyń. 5.2 Informacje wyłącznie na użytek niezależnych ośrodków przeprowadzających testy i akredytowanych laboratoriów info.test@dishwasher-production.com Należy zapisać numer produktu (PNC) podany na tabliczce znamionowej.
POLSKI Im wyższa zawartość substancji mineralnych, tym twardsza jest woda. Twardość wody jest mierzona w równoważnych skalach. 55 doprowadzonej do urządzenia. W lokalnym zakładzie wodociągowym można uzyskać informację na temat twardości wody. Istotne jest ustawienie właściwego poziomu zmiękczania wody, aby zapewnić dobre rezultaty zmywania.
www.aeg.com konieczności uzupełnienia płynu. Jeśli podczas stosowania wyłącznie tabletek wieloskładnikowych efekty suszenia są zadowalające, można wyłączyć powiadomienie o konieczności uzupełnienia płynu nabłyszczającego. Jednak aby zapewnić najlepsze efekty suszenia, należy zawsze używać płynu nabłyszczającego. Stosując standardowe tabletki wieloskładnikowe bez środka nabłyszczającego, należy włączyć funkcję powiadomienia, aby wskaźnik sygnalizujący konieczność uzupełnienia płynu pozostał aktywny.
POLSKI Funkcja AirDry włącza się automatycznie we wszystkich programach z wyjątkiem (jeśli występuje). Aby poprawić skuteczność suszenia, należy skorzystać z opcji XtraDry lub włączyć opcję AirDry. UWAGA! Jeśli do urządzenia mają dostęp dzieci, zaleca się wyłączenie funkcji AirDry, ponieważ samoczynne otworzenie się drzwi może być dla nich niebezpieczne. 1. Nacisnąć 57 . • Wskaźniki wyłączone. , i • • Wskaźnik nadal miga. Na wyświetlaczu pojawi się aktualne ustawienie: AirDry włączona.
www.aeg.com 7.2 TimeSaver Ta opcja powoduje zwiększenie ciśnienia oraz temperatury wody. Fazy zmywania i suszenia zostają skrócone. Całkowity czas trwania programu skraca się o około 50%. Efekty zmywania są takie same jak dla programu o standardowym czasie trwania. Jedynie skuteczność suszenia może być niższa. Włączanie opcji TimeSaver Nacisnąć . Włączy się odpowiedni wskaźnik. Wyświetlacz wyświetli zaktualizowany czas trwania programu. 8. PRZED PIERWSZYM UŻYCIEM 1.
POLSKI 8.2 Napełnianie dozownika płynu nabłyszczającego A D UWAGA! Należy stosować wyłącznie płyn nabłyszczający przeznaczony do zmywarek. B C B A 1. Nacisnąć przycisk zwalniający (D), aby otworzyć pokrywę (C). 2. Wlać płyn nabłyszczający do dozownika (A), aż osiągnie poziom napełnienia „max”. 3. Rozlany płyn nabłyszczający należy zetrzeć za pomocą chłonnej szmatki, aby zapobiec powstaniu zbyt dużej ilości piany. 4. Zamknąć pokrywę. Upewnić się, że przycisk zwalniający jest odpowiednio zablokowany.
www.aeg.com A 30 B 4. Ustawić odpowiednie opcje. 5. Zamknąć drzwi urządzenia, aby uruchomić program. D Uruchamianie programu z opóźnieniem 20 1. Ustawić program. C 1. Nacisnąć przycisk zwalniający (B), aby otworzyć pokrywę (C). 2. Umieścić detergent, w postaci proszku lub tabletki, w przegródce (A). 3. Jeżeli wybrano program obejmujący zmywanie wstępne, należy umieścić niewielką ilość detergentu w przegródce (D). 4. Zamknąć pokrywę.
POLSKI Anulowanie opóźnienia rozpoczęcia programu w trakcie odliczania Zakończenie programu Po anulowaniu opóźnienia rozpoczęcia programu należy ponownie ustawić program. Wszystkie przyciski są nieaktywne z wyjątkiem przycisku wł./wył. Nacisnąć i przytrzymać przycisk RESET, aż urządzenie znajdzie się w trybie wyboru programów. Anulowanie programu Nacisnąć i przytrzymać przycisk RESET, aż urządzenie znajdzie się w trybie wyboru programów.
www.aeg.com wskazówkami podanymi na opakowaniu detergentu. 10.3 Postępowanie po zaprzestaniu korzystania z tabletek wieloskładnikowych Przed rozpoczęciem stosowania oddzielnie dozowanego detergentu, soli i płynu nabłyszczającego należy wykonać poniższą procedurę. 1. Ustawić najwyższy poziom zmiękczania wody. 2. Upewnić się, że zbiornik soli oraz dozownik płynu nabłyszczającego są pełne. 3. Uruchomić najkrótszy program z fazą płukania. Nie dodawać detergentu ani nie umieszczać naczyń w koszach. 4.
POLSKI 63 11. KONSERWACJA I CZYSZCZENIE OSTRZEŻENIE! Przed przystąpieniem do konserwacji należy wyłączyć urządzenie i wyjąć wtyczkę przewodu zasilającego z gniazda elektrycznego. Brudne filtry i zapchane ramiona spryskujące pogarszają efekt zmywania. Należy je regularnie sprawdzać i w razie potrzeby wyczyścić. 2. Wyjąć filtr (C) z filtra (B). 3. Wyjąć filtr płaski (A). 4. Umyć filtry. 11.1 Czyszczenie filtrów System filtrów składa się z 3 części. C B A 5.
www.aeg.com 11.3 Czyszczenie obudowy • • • Czyścić urządzenie za pomocą wilgotnej szmatki. Używać wyłącznie neutralnych detergentów. Nie używać produktów ściernych, myjek do szorowania ani rozpuszczalników. 11.4 Czyszczenie wnętrza • UWAGA! Nieprawidłowe umiejscowienie filtrów może skutkować niezadowalającymi efektami zmywania i uszkodzeniem urządzenia. 11.2 Czyszczenie ramion spryskujących Nie wolno wyjmować ramion spryskujących.
POLSKI Problem i kod alarmowy Możliwa przyczyna i rozwiązanie Urządzenie nie włącza się. • • Program nie uruchamia się. • • • Urządzenie nie napełnia się wodą. Na wyświetlaczu widoczne jest wskazanie lub • • . Urządzenie nie wypompo‐ wuje wody. Na wyświetlaczu widoczne jest wskazanie . • • • • • • • Włączyło się zabezpieczenie • przed zalaniem. Na wyświetlaczu widoczne jest wskazanie 65 Upewnić się, że wtyczkę przewodu zasilającego włożo‐ no do gniazdka.
www.aeg.com Problem i kod alarmowy Możliwa przyczyna i rozwiązanie Występują problemy z za‐ mknięciem drzwi urządze‐ nia. • Grzechotanie/stukanie do‐ chodzące z wnętrza urzą‐ dzenia. • Urządzenie wyzwala auto‐ matyczny wyłącznik. • Urządzenie nie jest dobrze wypoziomowane. Poluzować lub dokręcić regulowane nóżki (jeśli dotyczy). Naczynia wystają z koszy. • Naczynia nie są prawidłowo rozłożone w koszach. Nale‐ ży zapoznać się z broszurą dotyczącą załadunku koszy.
POLSKI Problem Możliwa przyczyna i rozwiązanie Niezadowalające efekty su‐ szenia. • • • • • Białawe smugi lub niebieska‐ wy nalot na szklankach i na‐ czyniach. • • 67 Naczynia pozostawały za długo w zamkniętym urzą‐ dzeniu. Nie ma płynu nabłyszczającego lub dozowana jest je‐ go niewystarczająca ilość. Ustawić wyższy poziom do‐ zowania płynu nabłyszczającego. Przedmioty z tworzywa sztucznego mogą wymagać wytarcia ściereczką.
www.aeg.com Problem Możliwa przyczyna i rozwiązanie Po zakończeniu programu w • dozowniku znajdują się pozos‐ tałości detergentu. • • Tabletka z detergentem zablokowała się w dozowniku i woda nie wypłukała jej całkowicie. Woda nie wypłukała detergentu z dozownika. Należy sprawdzić, czy ramię spryskujące może się obracać i jest drożne. Sprawdzić, czy przedmioty w koszach nie uniemożli‐ wiają otworzenia pokrywy dozownika detergentu. Nieprzyjemny zapach w urzą‐ dzeniu. • Patrz „Czyszczenie wnętrza”.
POLSKI Ciśnienie doprowadzanej wo‐ Min./maks. bar (MPa) dy 0.5 (0.05) / 8 (0.8) Dopływ wody Zimna lub ciepła woda 2) maks. 60°C Pojemność Liczba kompletów naczyń 13 Pobór mocy Tryb czuwania (W) 5.0 Pobór mocy Tryb wyłączenia (W) 0.50 69 1) Pozostałe wartości znajdują się na tabliczce znamionowej. 2) Jeżeli ciepła woda pochodzi z alternatywnych źródeł energii (np. z kolektorów słonecznych, elektrowni wiatrowych), można użyć jej do zasilania urządzenia, aby zmniejszyć zużycie energii. 14.
www.aeg.
POLSKI 71
156908433-A-072018 www.aeg.